Structural and optical properties of 6CaO·6SrO·7Al2O3 thin films derived by sol-gel dip coating process

The nanostructured 6CaO·6SrO·7Al₂O₃ (C6S6A7) thin films with cubic structure using calcium, strontium metals, aluminium isopropoxide and ethylene glycol monomethyl ether as stating materials has been fabricated via sol-gel route. Based on hydrolysis of Ca²⁺, Sr²⁺ and Al³⁺ in the sol-gel processing using ethylene glycol monomethyl ether as solvent have been employed as the precursor material. The films were coated on soda lime float glass by the dip coating technique and annealed at 450 °C in air atmosphere. The structure, morphology and composition of the films were investigated by Fourier transformed infrared spectroscopy, X-ray powder diffraction, scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy indicating that the films were composed of C6S6A7 nanoparticles with cubic structure. The spectral transmittance of the films was measured in the wavelength range of 200-1100 nm using an UV-visible spectrometer. It has been found that the optical properties of the films significantly affected by precursor chemistry and annealing temperature due to the improvement of the crystallinity of the films with increasing annealing temperature and became stable when the annealing temperature is higher than 450 °C. The C6S6A7 films annealed at 450 °C had high transparency about 80% in wide visible range.     

Influence of annealing on the physical properties of filtered vacuum arc deposited tin oxide thin films

Tin oxide (SnO₂) thin films were deposited on UV fused silica (UVFS) substrates using filtered vacuum arc deposition (FVAD). During deposition, the substrates were at room temperature (RT). As-deposited films were annealed at 400 and 600 °C in Ar for 30 min. The film structure, composition, and surface morphology were determined as function of the annealing temperature using X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The XRD patterns of the SnO₂ thin films deposited on substrates at RT indicated that the films were amorphous, however, after the annealing the film structure became polycrystalline. The grain size of the annealed films, obtained from the XRD analysis, increased with the annealing temperature, and it was in the range 8-34 nm. The AFM analysis of the surface revealed an increase in the film surface average grain size from 15 nm to 46 nm, and the surface roughness from 0.2 to 1.8 nm, as function of the annealing temperature. The average optical transmission of the films in the visible spectrum was >80%, and increased by the annealing ∼10%. The films’ optical constants in the 250-989 nm wavelength range were determined by variable angle spectroscopic ellipsometry (VASE). The refractive indexes of as-deposited and annealed films were in the range 1.83-2.23 and 1.85-2.3, respectively. The extinction coefficients, k(λ), of as-deposited and annealed films were in the range same range ∼0-0.5. The optical energy band gap (E_g), as determined by the dependence of the absorption coefficient on the photon energy at short wavelengths, increased with the annealing temperature from 3.90 to 4.35 eV. The lowest electrical resistivity of the as-deposited tin oxide films was 7.8 × 10⁻³ Ω cm, however, film annealing resulted in highly resistive films.     

Influence of hydrogen on structural and optical properties of low temperature polycrystalline Ge films deposited by RF magnetron sputtering

To improve the properties of polycrystalline Ge thin films, which are a candidate material for the bottom cells of low cost monolithic tandem solar cells, ∼300 nm in situ hydrogenated Ge (Ge:H) thin films were deposited on silicon nitride coated glass by radio-frequency magnetron sputtering. The films were sputtered in a mixture of 15 sccm argon and 10 sccm hydrogen at a variety of low substrate temperatures (T_s)≤450 °C. Structural and optical properties of the Ge:H thin films were measured and compared to those of non-hydrogenated Ge thin films deduced in our previous work. Raman and X-ray diffraction spectra revealed a structural evolution from amorphous to crystalline phase with increase in T_s. It is found that the introduction of hydrogen gas benefits the structural properties of the polycrystalline Ge film, sputtered at 450 °C, although the onset crystallization temperature is ∼90 °C higher than in those sputtered without hydrogen. Compared with non-hydrogenated Ge thin films, hydrogen incorporated in the films leads to broadened band gaps of the films sputtered at different T_s.     

Preparation and characterization of ZnO-TiO2 films obtained by sol-gel method

The sol-gel route has been applied to obtain ZnO-TiO₂ thin films. For comparison, pure TiO₂ and ZnO films are also prepared from the corresponding solutions. The films are deposited by a spin-coated method on silicon and glass substrates. Their structural and vibrational properties have been studied as a function of the annealing temperatures (400-750 °C). Pure ZnO films crystallize in a wurtzite modification at a relatively low temperature of 400 °C, whereas the mixed oxide films show predominantly amorphous structure at this temperature. XRD analysis shows that by increasing the annealing temperatures, the sol-gel Zn/Ti oxide films reveal a certain degree of crystallization and their structures are found to be mixtures of wurtzite ZnO, Zn₂TiO₄, anatase TiO₂ and amorphous fraction. The XRD analysis presumes that Zn₂TiO₄ becomes a favored phase at the highest annealing temperature of 750 °C. The obtained thin films are uniform with no visual defects. The optical properties of ZnO-TiO₂ films have been compared with those of single component films (ZnO and TiO₂). The mixed oxide films present a high transparency with a slight decrease by increasing the annealing temperature.     

The effects of annealing temperature on photoluminescence of silicon nanoparticles embedded in SiNx matrix

The effects of the annealing temperature on photoluminescence (PL) of non-stoichiometric silicon nitride (SiN_x) thin films deposited by plasma enhanced chemical vapor deposition (PECVD) using ammonia and silane mixtures at 200 °C were investigated. The optical property and the chemical composition of the films annealed at different temperatures were investigated by PL spectroscopy and Fourier transform infrared absorption spectroscopy (FTIR), respectively. Based on the PL results and the analyses of the bonding configurations of the films, the light emission is attributed to the quantum confinement effect of the carriers inside silicon nanoparticles and radiative defect-related states. These results provide a better understanding of optical properties of silicon nanoparticles embedded in silicon nitride films and are useful for the application of nanosize silicon semiconductor material.     

Electrical, structural and optical properties of SnO2 thin films prepared by spray pyrolysis

This study investigated the effect of the substrate temperature on the structural, optical, morphological, and electrical properties of undoped SnO₂ films prepared by a spray deposition method. The films were deposited at various substrate temperatures ranging from 300-500 °C in steps of 50 °C and characterized by different optical and structural techniques. X-ray diffraction studies showed that the crystallite size and preferential growth directions of the films were dependent on the substrate temperature. These studies also indicated that the films were amorphous at 300 °C and polycrystalline at the other substrate temperatures used. Infrared and visible spectroscopic studies revealed that a strong vibration band, characteristic of the SnO₂ stretching mode, was present around 630 cm⁻¹ and that the optical transmittance in the visible region varied over the range 75-95% with substrate temperature, respectively. The films deposited at 400 °C exhibited the highest electrical conductivity property.     

Growth of epitaxial TmFeCuO4 thin films by pulsed laser deposition

Epitaxial thin films of TmFeCuO₄ with a two-dimensional triangular lattice structure were successfully grown on yttria-stabilized-zirconia substrates by pulsed laser deposition and ex situ annealing in air. The films as-deposited below 500 °C showed no TmFeCuO₄ phase and the subsequent annealing resulted in the decomposition of film components. On the other hand, as-grown films deposited at 800 °C showed an amorphous nature. Thermal annealing converted the amorphous films into highly (0 0 1)-oriented epitaxial films. The results of scanning electron microscopic analysis suggest that the crystal growth process during thermal annealing is dominated by the regrowth of non-uniformly shaped islands to the distinct uniform islands of hexagonal base.     

Metal organic vapour phase epitaxy of MgO films grown on c-plane Sapphire

Metal organic vapour phase epitaxy (MOVPE) has been used to epitaxially grow MgO films on c-plane sapphire substrates. Bismethylcyclopentadienyl magnesium (MCP₂Mg) and nitrous oxide (N₂O) were used as the magnesium and the oxygen source, respectively, with nitrogen (N₂) as the carrier gas. The dependence of the growth rate on the partial pressure of magnesium and on the growth temperature was investigated. The growth rate increases with the magnesium partial pressure. The morphological and structural properties of MgO films were investigated using atomic force microscopy and X-ray diffraction. The structural properties are strongly dependent on the growth temperature in the range 400–800 °C. (1 1 1)-oriented MgO layers are observed at growth temperatures above 600 °C whereas no diffraction peak is found at lower growth temperatures. The atomic force microscopy (AFM) images reveal a smooth surface morphology.     

Growth and microstructural features of laser ablated LiCoO2 thin films

Thin films of LiCoO₂ were prepared by pulsed laser deposition technique and the properties were studied in relation to the deposition parameters. The films deposited from a sintered composite target (LiCoO₂+Li₂O) in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 300 °C exhibited preferred c-axis (0 0 3) orientation perpendicular to the substrate surface. The AFM data demonstrated that the films are composed of uniform distribution of fine grains with an average grain size of 80 nm. The grain size increased with an increase in substrate temperature. The (0 0 3) orientation decreased with increase in (1 0 4) orientation for the films deposited at higher substrate temperatures (>500 °C) indicating that the films’ growth is parallel to the substrate surface. The composition of the experimental films was analyzed using X-ray photoelectron spectroscopy (XPS). The binding energy peaks of Co(2p_3/2) and Co(2p_1/2) are, respectively, observed at 779.3 and 794.4 eV, which can be attributed to the Co³⁺ bonding state of LiCoO₂. The electrochemical measurements were carried out on Li//LiCoO₂ cells with a lithium metal foil as anode and LiCoO₂ film as cathode of 1.5 cm² active area using a Teflon home-made cell hardware. The Li//LiCoO₂ cells were tested in the potential range 2.6-4.2 V. Specific capacity as high as 205 mC/cm² μm was measured for the film grown at 700 °C. The growth of LiCoO₂ films were studied in relation to the deposition parameters for their effective utilization as cathode materials in solid-state microbattery application.     

In-situ cyclic pulse annealing of InN on AlN/Si during IR-lamp-heated MBE growth

To improve crystal quality of InN, an in-situ cyclic rapid pulse annealing during growth was carried out using infrared-lamp-heated molecular beam epitaxy. A cycle of 4 min growth of InN at 400 °C and 3 s pulse annealing at a higher temperature was repeated 15 times on AlN on Si substrate. Annealing temperatures were 550, 590, 620, and 660 °C. The back of Si was directly heated by lamp irradiation through a quartz rod. A total InN film thickness was about 200 nm. With increasing annealing temperature up to 620 °C, crystal grain size by scanning electron microscope showed a tendency to increase, while widths of X-ray diffraction rocking curve of (0 0 0 2) reflection and E₂ (high) mode peak of Raman scattering spectra decreased. A peak of In (1 0 1) appeared in X-ray diffraction by annealing higher than 590 °C, and In droplets were found on the surface by annealing at 660 °C.     

1H-1,2,3-triazole,a promising precursor for chemical vapor deposition of hydrogenated carbon nitride

Well-crystallized hydrogenated carbon nitride thin films have been prepared by microwave plasma enhanced chemical vapor deposition (MWPECVD). 1H-1,2,3-triazole+N₂ and Si (1 0 0) were used as precursor and substrate, respectively. Substrate temperature during the deposition was recorded to be 850 °C. The synthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photo-electron spectroscopy (XPS) analyses. The plasma compositions were checked by optical emission spectroscopy (OES). XRD observation strongly suggests that the films contain polycrystalline carbon nitride with graphitic structure of (1 0 0), (0 0 2), (2 0 0) and (0 0 4). XPS peak quantification reveals that the atomic ratio of the materials C:N:O:Si is 32:41:18:9. X-ray photo-electron peak deconvolution shows that the most dominant peak of C (1s) and N (1s) narrow scans correspond to sp² hybrid structure of C₃N₄. These observations indicate that 1H-1,2,3-triazole favors the formation of hydrogenated carbon nitride with graphitic phase by CVD method and thus is in good agreement with XRD results. SEM of surface and OES of plasma also support the formation of polycrystalline carbon nitride films from 1H-1,2,3-triazole+N₂ by CVD.     

Fluorinated nanoporous SiO2 films with ultra-low dielectric constant

Fluorinated nanoporous silica (denoted as SiO₂:F) thin films with low dielectric constant were prepared by a sol-gel method and spin coating technique. The leakage current densities of the SiO₂:F thin films were 10⁻⁸ and 3 × 10⁻⁶ A/cm² respectively for the as-deposited films and for those subjected to annealing at a temperature of 450 °C. These currents are more than one order of magnitude lower than those of the common SiO₂ films. Photoluminescent results showed strong blue-light emission and a small blue shift in the SiO₂:F films that were related to the increment of the porosity. The dielectric properties were also characterized and the k value of the annealed SiO₂:F film was found to be about 1.67. The hole size in the films is small and the size distribution is uniform for the annealed SiO₂:F samples due to the effects of fluorination. The underlying mechanism for fluorination is discussed in this paper.     

Influence of annealing condition on the properties of sputtered hafnium oxide

Hafnium oxide thin films were deposited on p-type (1 0 0) silicon wafers by reactive dc magnetron sputtering. Prior to the deposition of HfO₂ films, a thin Hf film was deposited. Sputtered HfO₂ thin films deposited at room temperature remain amorphous at T<650°C and orthorhombic phases were observed above 650 °C. The monoclinic phase which is a stable HfO₂ polymorphic form appeared after annealing above 800 °C. Capacitance equivalent thickness values decreased and leakage characteristics are improved by the Hf interlayer and O₂ settlement process. The decrease of accumulation capacitance values upon annealing is due to the growth of an interfacial layer upon post-annealing. The flat band voltage (V_FB) shifts negatively due to positive charge generated during post-annealing.     

Growth of GaN films on PLD-deposited TaC substrates

GaN films were grown by metal organic chemical vapor deposition on TaC substrates that were created by pulsed laser deposition of TaC onto (0 0 0 1) SiC substrates at ∼1000 °C. This was done to determine if good quality TaC films could be grown, and if good quality GaN films could be grown on this closely lattice matched to GaN, conductive material. This was done by depositing the TaC on on-axis and 3° or 8° off-axis (0 0 0 1) SiC at temperatures ranging from 950 to 1200 °C, and examining them using X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. The GaN films were grown on as-deposited TaC films, and films annealed at 1200, 1400, or 1600 °C, and examined using the same techniques. The TaC films were polycrystalline with a slight (1 1 1) texture, and the grains were ∼200 nm in diameter. Films grown on-axis were found to be of higher quality than those grown on off-axis substrates, but the latter could be improved to a comparable quality by annealing them at 1200–1600 °C for 30 min. TaC films deposited at temperatures above 1000 °C were found to react with the SiC. GaN films could be deposited onto the TaC when the surface was nitrided with NH₃ for 3 min at 1100 °C and the low temperature buffer layer was AlN. However, the GaN did not nucleate easily on the TaC film, and the crystallites did not have the desired (0 0 0 1) preferred orientation. They were ∼10 times larger than those typically seen in films grown on SiC or sapphire. Also the etch pit concentration in the GaN films grown on the TaC was more than 2 orders of magnitude less than it was for growth on the SiC.     

Epitaxial growth of InN films on lattice-matched EuN buffer layers

Indium nitride (InN) films have been grown on lattice matched europium nitride (EuN) buffer layers by pulsed laser deposition (PLD) and their structural properties have been investigated. It has been revealed that the growth of EuN films on Al₂O₃ (0 0 0 1) substrates leads to the formation of polycrystalline EuN films, whereas epitaxial EuN (1 1 1) films grow on MgO (1 1 1) substrates at 860 °C. By using the EuN (1 1 1) films as buffer layers for InN growth, we have succeeded in the epitaxial growth of InN (0 0 0 1) films at 490 °C with an in-plane epitaxial relationship of [1 1 2¯ 0]_InN∥[1 1¯ 0]_EuN∥[1 1¯ 0]_MgO, which minimized the lattice mismatch between InN and EuN.     

Effect of N2/CH4 flow ratio on microstructure and composition of hydrogenated carbon nitride films prepared by a dual DC-RF plasma system

Hydrogenated carbon nitride (a-CN:H) films were deposited on n-type (1 0 0) silicon substrates making use of direct current radio frequency plasma enhanced chemical vapor deposition (DC-RF-PECVD), using a gas mixture of CH₄ and N₂ as the source gas in range of N₂/CH₄ flow ratio from 1/3 to 3/1 (sccm). The deposition rate, composition and bonding structure of the a-CN:H films were characterized by means of X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectrometry (FTIR). The mechanical properties of the deposited films were evaluated using nano-indentation test. It was found that the parameter for the DC-RF-PECVD process had significant effects on the growth rate, structure and properties of the deposited films. The deposition rate of the films decreased clearly, while the N/C ratio in the films increased with increasing N₂/CH₄ flow ratio. CN radicals were remarkably formed in the deposited films at different N₂/CH₄ flow ratio, and their contents are related to the nitrogen concentrations in the deposited films. Moreover, the hardness and Young’s modulus of the a-CN:H films sharply increased at first with increasing N₂/CH₄ flow ratio, then dramatically decreased with further increase of the N₂/CH₄ flow ratio, and the a-CN:H film deposited at 1/1 had the maximum hardness and Young’s modulus. In addition, the structural transformation from sp³-like to sp²-like carbon-nitrogen network in the deposited films also was revealed.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Microstructure and dielectric properties of La2O3 films prepared by ion beam assistant electron-beam evaporation

Ultrathin La₂O₃ gate dielectric films were prepared on Si substrate by ion assistant electron-beam evaporation. The growth processing, interfacial structure and electrical properties were investigated by various techniques. From XRD results, we found that the La₂O₃ films maintained the amorphous state up to a high annealing temperature of 900 °C for 5 min. From XPS results, we also discovered that the La atoms of the La₂O₃ films did not react with silicon substrate to form any La-compound at the interfacial layer. However, a SiO₂ interfacial layer was formed by the diffusion of O atoms of the La₂O₃ films to the silicon substrate. From the atomic force microscopy image, we disclosed that the surface of the amorphous La₂O₃ film was very flat. Moreover, the La₂O₃ film showed a dielectric constant of 15.5 at 1 MHz, and the leakage current density of the La₂O₃ film was 7.56 × 10⁻⁶ A/cm² at a gate bias voltage of 1 V.     

MOVPE growth of InN films using 1,1-dimethylhydrazine as a nitrogen precursor

InN films have been successfully grown on sapphire substrates by MOVPE using trimethylindium (TMIn) and 1,1-dimethylhydrazine (DMHy) with N₂ carrier. DMHy is an advantageous precursor of N as it decomposes efficiently at relatively low temperature (T₅₀=420 °C) compatible with the InN growth. The reactor is specially designed so as to avoid parasitic reaction between TMIn and DMHy occurring at room temperature. The growth feature was studied by varying growth temperature, V/III ratio, TMIn flow and reactor pressure. The InN films were obtained at 500–570 °C and 60–200 Torr with a V/III ratio optimized to 100–200. The In droplets are seen on the grown surfaces, indicating an excess supply of TMIn. It is demonstrated that the InN films grows on the sapphire substrate in a single domain with an epitaxial relationship, [1 01¯ 0]_InN//[1 1 2¯ 0]_sapphire.