Synthesis of sodium silicate-based hydrophilic silica aerogel beads with superior properties: Effect of heat-treatment

This work demonstrates the synthesis of hydrophilic and hydrophobic high surface area silica aerogel beads with a large pore volume. Wet gel silica beads were modified and heat-treated under atmospheric pressure after modification of the surface by trimethychlorosilane (TMCS). The effects of heat treatment on the physical (hydrophobicity) and textural properties (specific surface area, pore volume, and pore size) of silica aerogel beads were investigated. The results indicated that hydrophobicity of the silica aerogel beads can be maintained up to 400 °C. The hydrophobicity of the silica aerogel beads decreased with increasing temperature in the range of 200-500 °C, and the beads became completely hydrophilic after heat treatment at 500 °C. The specific surface area, cumulative pore volume, and pore size of the silica aerogel beads increased with increasing temperature. Heating the TMCS modified bead gel at 400 °C for 1 h resulted in silica aerogel beads with high surface area (769 m²/g), and large cumulative pore volume (3.10 cm³/g). The effects of heat treatment on the physical and textural properties of silica aerogel beads were investigated by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), thermogravimetric and differential analysis (TG-DTA), Fourier-transform infrared spectroscopy (FT-IR), and Brunauer, Emmett and Teller (BET) and BJH nitrogen gas adsorption and desorption methods.     

Synthesis and characterization of Bi3.15Nd0.85Ti3O12 nanotube arrays

Nd-substituted bismuth titanate (Bi_3.15Nd_0.85Ti₃O₁₂, BNT) nanotube arrays are fabricated by means of a sol–gel method utilizing porous anodic aluminum oxide (AAO) template. The morphologies and structures have been determined by scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The diameter and length of these nanotubes are about 200 nm and 60 μm, respectively, and their wall thickness is about 30 nm. The average grain size is around 40 nm. XRD data show that the BNT nanotubes possess bismuth-layered perovskite structure. High-resolution electron microscopy (HRTEM) image demonstrates that the BNT nanotubes are polycrystalline. Polarization–electric field (P–E) response curves of BNT nanotube arrays were measured, and a size induced polarization reduction phenomenon is observed.     

Phase separation, crystallization and leaching of microporous glass ceramics in the CaO-TiO2-P2O5 system

Microporous glass ceramics belonging to the CaO-TiO₂-P₂O₅ system were prepared with the assumption of a 2:1 mole ratio for β-Ca₃(PO₄)₂:CaTi₄(PO₄)₆, the anticipated crystalline phases in the end product. The glasses formulated according to the above composition were melted and cast onto a steel mold and were crystallized to glass ceramics containing the above phases. Dilatometric/differential thermal analysis (DTA) techniques were utilized to determine the appropriate phase separation-nucleation and crystallization temperatures. The crystalline products and resulting microstructures in various stages of process were determined and observed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). By leaching the resulting glass ceramics in HCl, β-Ca₃(PO₄)₂ was dissolved out leaving a porous skeleton of CaTi₄(PO₄)₆. It was found that the volume porosity, specific surface area and mean pore diameter of microporous glass ceramics can be managed through the proper selection of heat treatment conditions. In the optimized conditions for fabricating glass ceramics of minimum mean pore size the values of 41 ± 4%, 26 ± 3 m²/g and 14.3 ± 2 nm were obtained for porosity, surface area and pore diameter respectively.     

Synthesis and Judd-Ofelt analysis of a sol-gel material doped with a Ln2(Benzoate)6(Phen)2 (Ln = Er/Yb) complex

In this work, we have prepared a sol-gel derived hybrid material directly doped with Er_1.4Yb_0.6(Benzoate)₆(Phen)₂ (Phen = 1,10-phenanthroline) complex, which was reported with intramolecular Yb-Er energy-transfer process in our previous work. The infrared (IR) spectra of the pure complex and hybrid gel material were investigated. The NIR photoluminescence (PL) spectrum of hybrid gel material shows strong characteristic emission of Er³⁺ with broad full width at half-maximum (FWHM) of 70 nm. Judd-Ofelt theory was used in order to analyze the optical properties of Er³⁺ ions in the hybrid gel material.     

One-step fabrication of Fe2O3/Ag core-shell composite nanoparticles at low temperature

The Fe₂O₃/Ag core-shell composite nanoparticles were successfully prepared via a simple method at low temperature. X-ray diffraction data revealed the formation of core-shell composite nanoparticles, with Fe₂O₃ as the core and silver as the shell. The results from the transmission electron microscopy and scan electron microscopy further indicated that the composite nanoparticles were spherical with a core diameter and shell thickness of 26.0 nm and 13.5 nm, respectively. Magnetic measurements showed that the composite nanoparticles exhibited a typical ferromagnetic behavior, a specific saturation magnetization of 0.95 emu/g and an intrinsic coercivity of 104.0 Oe at room temperature. For a standard two-probe analysis at room temperature, the composite nanoparticles showed a typical conductive behavior and its conductivity was about 3.41 S/m. Moreover, this present synthesis method of Fe₂O₃/Ag core-shell composite nanoparticles shows an easy processing and does not need high-temperature calcining to attain the final product, which can be applied in a variety of areas, including catalysis, medicine, photonics, and new functional device assemblies.     

Ultralow density silica aerogels prepared with PEDS

This paper deals with the synthesis of ultralow density silica aerogels using polyethoxydisiloxanes (PEDS) as the precursor via sol-gel process followed by supercritical drying using ethanol solvent extraction. Ultralow density silica aerogels with 5 mg/cc of density were made for the molar ratio by this method. A remarkable reduction in the gelation time was observed by the effect of the catalyst NH₄OH at room temperature. The microstructure and morphology of the ultralow density silica aerogels were characterized by the specific surface area, S_BET, SEM, TEM and the pore size distribution techniques. The results show that the diameter of the silica particles is about 13 nm and the pore size of the silica aerogels is about several nm. The specific surface area of the silica aerogel is 339 m²/g and the specific surface area, pore volume and average pore diameter decrease with increasing density of the silica aerogel.     

Preparation of Sb2S3 nanomaterials with different morphologies via a refluxing approach

Single-crystalline antimony trisulfide (Sb₂S₃) nanomaterials with flower-like and rod-like morphologies were successfully synthesized under refluxing conditions by the reaction of antimony trichloride (SbCl₃) and thiourea with PEG400 and OP-10 as the surfactants. X-ray diffraction (XRD) indicates that the obtained sample is orthorhombic-phase Sb₂S₃ with calculated lattice parameters a=1.124 nm, b=1.134 nm and c=0.382 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images show that the flower-like Sb₂S₃ is 9–10 μm in size, which is composed of thin leaves with thickness of 0.05–0.2 μm, width of 0.8–2.2 μm and length of 2.5–3 μm, and the rod-like Sb₂S₃ is 45–360 nm in diameter and 0.7–4 μm in length, respectively. UV–Vis analysis indicates that the band gap of Sb₂S₃ nanorods is 1.52 eV, suitable for photovoltaic conversion. A possible mechanism of formation was proposed. The effects of reaction time and surfactants on the growth of nanomaterials with different morphologies were also investigated.     

Synthesis and characterization of single-crystalline PrCO3OH dodecahedral microrods and its thermal conversion to Pr6O11

Single-crystalline PrCO₃OH dodecahedral microrods with an orthorhombic structure have been successfully synthesized by the hydrothermal method used urea as the precipitator. Pr₆O₁₁ dodecahedral microrods have been obtained by thermal conversion of PrCO₃OH dodecahedral microrods at 600 °C in air for 6 h. The as-synthesized products were characterized by X-ray powder diffraction, field-emission scanning electron microscope, transmission electron microscopy, high-resolution transmission electron microscopy, selected-area electron diffraction, X-ray photoelectron spectra, fourier transform infrared spectroscopy and thermogravimetry–differential thermal analysis. The effect of the reaction parameters on the morphology of the product has been investigated. The dodecahedral microrods with larger size and better crystallinity can be obtained under the higher reaction temperature. The possible formation mechanism of PrCO₃OH microrods was discussed.     

Synthesis of Nb2O5·nH2O nanoparticles by water-in-oil microemulsion

Hydrous niobium oxide (Nb₂O₅·nH₂O) nanoparticles had been successfully prepared by water-in-oil microemulsion. They were characterized by X-ray diffraction (XRD), thermal analysis (TG/DTG), Fourier transform infrared spectroscopy (FTIR), BET surface area measurement, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the nanoparticle was exactly Nb₂O₅·nH₂O with spherical shape. Their BET surface area was 60 m² g⁻¹. XRD results showed that Nb₂O₅·nH₂O nanoparticles with crystallite size in nanometer scale were formed. The crystallinity and crystallity size increased with increasing annealing temperature. TT-phase of Nb₂O₅ was obtained when the sample is annealed at 550 °C.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Optical properties of and concentration quenching in Bi2O3-B2O3-Ga2O3 glasses

Er₂O₃-doped Bi₂O₃-B₂O₃-Ga₂O₃ glasses were prepared by the conventional melt-quenching method, and the Er³⁺:⁴I_13/2 → ⁴I_15/2 fluorescence properties are studied for different Er³⁺ concentrations. when the Er₂O₃ concentration increases from 0.03 to 3.0 mol%, the measured lifetime of Er³⁺:⁴I_13/2 level decrease from 2.24 to 0.9 m s, and from 0.25 to 0.20 m s for the Er³⁺:⁴I_11/2 level. The fast energy migration among Er³⁺ ions cause the reduction of lifetime of the ⁴I_13/2 level, whereas the change in the ⁴I_11/2 level is mainly due to a cooperative upconversion process (⁴I_11/2, ⁴I_11/2) → (⁴F_7/2, ⁴I_15/2). Based on the dipole-dipole interaction theory, the interaction parameter, C_Er,Er, for the migration rate of Er³⁺:⁴I_13/2 ↔ ⁴I_13/2 was calculated to be 32 × 10⁻⁴⁰ cm⁶ s⁻¹.     

Hydrothermal synthesis of Bi2Te3 nanowires through the solid-state interdiffusion of Bi and Te atoms on the surface of Te nanowires

Polycrystalline Bi₂Te₃ nanowires were prepared by a hydrothermal method that involved inducing the nucleation of Bi atoms reduced from BiCl₃ on the surface of Te nanowires, which served as sacrificial templates. A Bi–Te alloy is formed by the interdiffusion of Bi and Te atoms at the boundary between the two metals. The Bi₂Te₃ nanowires synthesized in this study had a length of 3–5 μm, which is the same length as that of the Te nanowires, and a diameter of 300–500 nm, which is greater than that of the Te nanowires. The experimental results indicated that volume expansion of the Bi₂Te₃ nanowires was a result of the interdiffusion of Bi and Te atoms when Bi was alloyed on the surface of the Te nanowires. The morphologies of Bi₂Te₃ are strongly dependent on the reaction conditions such as the temperature and the type and concentration of the reducing agent. The morphologies, crystalline structure and physical properties of the product were analyzed by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray photoelectron spectroscopy (XPS).     

Energetics of CdSxSe1−x quantum dots in borosilicate glasses

The thermodynamics of CdSe quantum dots embedded in a glass matrix is of great interest because of the numerous applications as optical materials. In this study, the energetics and stability of CdSe quantum dots in a borosilicate glass matrix is investigated as a function of size using high-temperature oxide melt solution calorimetry. CdS_0.1Se_0.9 nanoparticles (1-40 nm) embedded in glass were analyzed by photoluminescence spectroscopy, electron microprobe, X-ray fluorescence, high-energy synchrotron X-ray diffraction, and (scanning) transmission electron microscopy using both electron energy loss and energy dispersive X-ray spectroscopy. As CdSe particles coarsen, their heat of formation becomes more exothermic. The interfacial energy of CdSe QDs embedded in a borosilicate glass, determined from the slope of enthalpy of drop solution versus calculated surface area, is 0.56 ± 0.01 J/m².     

Microstructure and dielectric properties of La2O3 films prepared by ion beam assistant electron-beam evaporation

Ultrathin La₂O₃ gate dielectric films were prepared on Si substrate by ion assistant electron-beam evaporation. The growth processing, interfacial structure and electrical properties were investigated by various techniques. From XRD results, we found that the La₂O₃ films maintained the amorphous state up to a high annealing temperature of 900 °C for 5 min. From XPS results, we also discovered that the La atoms of the La₂O₃ films did not react with silicon substrate to form any La-compound at the interfacial layer. However, a SiO₂ interfacial layer was formed by the diffusion of O atoms of the La₂O₃ films to the silicon substrate. From the atomic force microscopy image, we disclosed that the surface of the amorphous La₂O₃ film was very flat. Moreover, the La₂O₃ film showed a dielectric constant of 15.5 at 1 MHz, and the leakage current density of the La₂O₃ film was 7.56 × 10⁻⁶ A/cm² at a gate bias voltage of 1 V.     

Preparation and optical properties of nanoscale MgAl2O4 powders doped with Co ions

Co²⁺-doped MgAl₂O₄ nanocrystalline powders were prepared by co-precipitation method. The gels and/or calcined samples were characterized by means of thermogravimetry and differential scanning calorimetry (TG/DSC), X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared (FTIR) spectrum and near-infrared absorption spectrum. MgAl₂O₄ nanocrystals were produced by calcining the gel above 800 °C, with the crystallite size of 10-30 nm in the temperature range of 800-1100 °C. The influence of pH value of precipitant solution on the dispersing of powders was studied and the result showed that Co:MgAl₂O₄ nanocrystalline powders exhibited good dispersion when pH = 11. The absorption spectrum of Co²⁺-doped MgAl₂O₄ exhibited a broad absorption band in the wavelength range of 1200-1600 nm, which indicated that Co²⁺ ions substituted for the tetrahedrally coordinated Mg²⁺ ions in the MgAl₂O₄ lattice.     

Investigation of infrared emission and lifetime in Tm-doped 75TeO2:20ZnO:5Na2O (mol%) glasses: Effect of Ho and Yb co-doping

In this paper we describe fabrication and characterization of rare-earth-doped active tellurite glasses to be used as active laser media for fiber lasers emitting in the 2 μm region. The base composition is (mol%): 75TeO₂-20ZnO-5Na₂O with different concentrations of Tm³⁺, Yb³⁺ and Ho³⁺ as dopants or co-dopants. Optical properties of doped glasses were studied and pumping at 800 nm and at 980 nm were tested in order to compare the efficiency of two pumping mechanisms. Optical characterization carried out on glasses containing only Tm³⁺ ions indicated the optimum concentration of Tm₂O₃ in terms of emission efficiency as 1 wt%. The addition of 5 wt% of Yb₂O₃ to Tm³⁺-doped glasses led to the best results in terms of intensity of fluorescence emission and of lifetime values. Yb and Ho co-doped Tm-tellurite glass was measured in emission.     

Structure of Ni/SiO2 films prepared by sol-gel dip coating

The sol-gel dip coating technique has been used to deposit composite oxide films (NiO)_x(SiO₂)_1−x with x = 0.1 on silicon wafers. Single and multilayer coatings allowed a variation of the film thickness from 70 to 400 nm. Film morphology, atomic structure and atomic composition have been investigated by transmission electron microscopy (TEM) and Rutherford backscattering spectrometry (RBS). The local environment of the Ni atoms was characterized by extended X-ray absorption fine structure (EXAFS). The samples were studied in the as-prepared state and after annealing in H₂ at 600 °C for 1 h. The structural and chemical state evolution of clusters present inside the silica matrix is discussed in terms of out-of-equilibrium reaction processes specific to low-dimensional objects and superficial effects.     

High surface area carbon aerogel monoliths with hierarchical porosity

This letter describes the synthesis and structural characterization of monolithic carbon aerogel (CA) materials that possess both high surface areas and hierarchical porosity. Thermal activation of a macroporous CA structure, one that was derived from an acetic acid-catalyzed sol-gel polymerization reaction, yields monolithic materials with large pore volumes and surface areas exceeding 3000 m²/g. Given the flexibility of CA synthesis, this approach offers viability to engineer new materials for use as catalyst supports, electrodes, capacitors and sorbent systems.     

Preparation and characterization of carbon aerogel microspheres by an inverse emulsion polymerization

Carbon aerogel (CA) microspheres have been successfully synthesized by an inverse emulsion polymerization and characterized by scanning electron microscopy (SEM), N₂ sorption isotherm and X-ray diffraction (XRD). The results show that the size and pore characteristics of carbon microsphere obviously depend on stirring speed and concentration of surfactant in the emulsion polymerization process. The resultant CA microspheres are amorphous carbon structure with the size ranging from about 2 to 50 μm by changing the stirring speed. CA microspheres with S_BET of 414-603 m² g^− 1 and V_meso of 0.028-0.432 cm³ g^− 1 are synthesized using different SPAN80 concentrations. The results of cyclic voltammetry indicate that the CA microspheres prepared at a stirring speed of 480 rpm and at V_s/V_h = 0.01 have ideal supercapacitive behavior in 6 M KOH electrolyte, the maximum specific capacitance of the electrode reaches 180 F g^− 1.     

Nano-scale structural inhomogeneities of CuI-Cu2MoO4 superionic conducting glass observed by high resolution transmission electron microscopy

Nano-meter sized structural inhomogeneities of (CuI)_0.52-(Cu₂MoO₄)_0.48 superionic conducting glass were investigated by high resolution transmission electron microscopy. The as-quenched sample of CuI-Cu₂MoO₄ is a homogeneous glass, in which the CuI component is finely and uniformly dispersed among the oxyanions of Cu₂MoO₄ glassy matrix. A two-step crystallization, starting at 440 and 495 K, was observed in the glass. After the first step crystallization, precipitating nano-crystalline cubic CuI 2-3 nm in diameter, the electrical conductivity increases by about 50%. On the other hand, the electrical conductivity decreases with the second crystallization event forming crystalline phases of CuI, Cu₂O and others 20-30 nm in diameter.