Spectroscopic properties of Er-doped xGeO2-(80 − x)TeO2-10ZnO-10BaO glasses

Erbium-doped glasses with composition xGeO₂-(80 − x)TeO₂-10ZnO-10BaO were prepared by melt-quenching technique. The phonon sideband spectra and the optical absorption band edges for the host matrix were confirmed by means of the spectral measurements. Standard Judd-Ofelt calculations have been completed to these glasses. The dependence of up-conversion and infrared emission under 980 nm excitation on the glass composition was studied. The quantum efficiencies for the ⁴I_13/2 → ⁴I_15/2 transition of trivalent erbium in the glasses were estimated.     

Three-dimensional structure of fast ion conducting 0.5Li2S + 0.5[(1 − x)GeS2 + xGeO2] glasses from high-energy X-ray diffraction and reverse Monte Carlo simulations

A high-energy X-ray diffraction study has been carried out on a series of 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses with x = 0.0, 0.1, 0.2, 0.4, 0.6 and 0.8. Structure factors were measured to wave vectors as high as 30 Å⁻¹ resulting in atomic pair distribution functions with high real space resolution. The three dimensional atomic-scale structure of the glasses was modeled by reverse Monte Carlo simulations based on the diffraction data. Results from the simulations show that at the atomic-scale 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses may be viewed as an assembly of independent chains of (Li^+-S)₂GeS_2/2 and (Li^+-O)₂GeO_2/2 tetrahedra as repeat units, where the Li ions occupy the open space between the chains. The new structure data may help understand the reasons for the sharp maximum in the Li⁺ ion conductivity at x ∼ 0.2.     

Formation, mechanical properties and corrosion resistance of Ti-Pd base glassy alloys

No biocompatible Ti-based glassy alloys without a harmful element have been reported. We have examined the mechanical and chemical properties of Ti-Pd-Zr-Si glassy alloy in comparison with pure Ti metal and Ti-6Al-4V alloy which have been used so far for biomaterials. The present Ti-Pd base glassy alloys do not contain Al and Ni elements which are considered to be rather toxic. Melt-spun Ti₄₅Zr_50−xPd_xSi₅ glassy alloy ribbons (x = 35, 40, 45) exhibited good bend ductility and had higher Vickers’s hardness and lower Young’s modulus as compared to pure titanium and Ti-6Al-4V alloy. In addition, the Ti₄₅Zr_50−xPd_xSi₅ glassy alloys had higher corrosion resistance and were passivated over a wide range and at the lower passive current density of approximately 10⁻² Am⁻² than at of pure titanium and Ti-6Al-4V alloy in 1 mass% lactic acid and PBS(−) solutions at 310 K.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

Far-infrared transmission and bonding arrangement in Ge10Se90−xTex semiconducting glassy alloys

The far-infrared spectra of Ge₁₀Se_90−xTe_x where x = 0, 10, 20, 30, 40, 50 glassy alloys were measured in the wavenumber region 50-650 cm⁻¹ at room temperature. The results were explained in terms of the vibrations of the isolated molecular units. The addition of Te in Ge₁₀Se₉₀ has shown the appearance of GeTe₂ and GeTe₄ molecular units and vibrations of Se-Te bond as Se_8−xTe_x mixed rings. The assignment of various absorption bands has been made on the basis of absorption spectra of pure Se, binary Ge-Se, Ge-Te, Se-Te and ternary Ge-Se-Te glassy alloys. The far-infrared transmission spectrum has been found to shift a little towards lower wavenumber side with the addition of Te content to Ge₁₀Se₉₀. The addition of Te to Ge-Se system replacing Se has found to reduce the Se-Se bonds and Ge-Se bonds and leads to the formation of Se-Te, Ge-Te and Te-Te bonds.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Crystal growth and characterization of two-leg spin ladder compounds: Sr14Cu24O41 and Sr2Ca12Cu24O41

Single crystals of Sr_14−xCa_xCu₂₄O₄₁ (x=0 and 12) are grown by the travelling solvent floating zone technique using an image furnace. The grown crystals are characterized for their single crystallinity by the X-ray and Neutron Laue method. The magnetic susceptibility measurements in Sr₁₄Cu₂₄O₄₁ show considerable anisotropy along the main crystallographic axes. Low-temperature specific heat measurement and DC susceptibility measurement in Ca-doped crystal showed antiferromagnetic ordering at 2.8 K at ambient pressure. High-pressure AC susceptibility measurement on Ca-doped crystal showed a sharp superconducting transition at 2 K under 40 kbars. T_c onset reached a maximum value of 9.9 K at 54 kbars. The bulk superconductivity of the sample is confirmed by the high-pressure AC calorimetry with T_c max=9.4 K and T_N=5 K at 56 kbars.     

Devitrification behavior and structure of Li2O-B2O3-Al2O3 composite gels from metal alkoxides

(30 − x/2)Li₂O·(70 − x/2)B₂O₃·xAl₂O₃(x = 0, 5 and 10) composite gels have been fabricated by the sol-gel method. LiOCH₃, B(OC₄H₉)₃, and Al(OC₄H₉)₃ were used as precursor for Li₂O, B₂O₃, and Al₂O₃, respectively. B(OC₄H₉)₃ and Al(OC₄H₉)₃ were hydrolyzed separately and then mixed. The crystallization behavior and structure of the gels upon thermal treatment temperatures between 150 and 550 °C are characterized on the basis of SEM, XRD and IR analyses. Xerogel with x = 0 exhibits non-crystal features, whereas crystalline phases are found in the xerogels with x = 5 and 10. The crystalline phases are not found with increasing heat treatment temperatures from 150 to 450 °C, but crystalline phases appear present at 550 °C. The xerogel with x = 0, subject to thermal treatment below 450 °C, is found to be still amorphous, and a 550 °C heat treatment leads its structure changing from glassy to crystalline.     

The effect of PbF2 content on the microstructure and upconversion luminescence of Er-doped SiO2-PbF2-PbO glass ceramics

The Er³⁺ doped transparent oxyfluoride glass ceramics were obtained by appropriate heat treatment of the precursor glasses with composition (mol%) 50SiO₂-xPbF₂-(50 − x)PbO-0.5ErF₃. The microstructure and optical properties of the glasses and glass ceramics were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), absorption spectra and luminescence spectra. The intensity of upconversion luminescence significantly increased in glass ceramics compared to that in precursor glass. The emission bands centered around 660 nm (⁴F_9/2 → ⁴I_15/2) and 410 nm (²H_9/2 → ⁴I_15/2) were simultaneously observed in glass ceramics but cannot be seen in the corresponding precursor glass. The influence of different PbF₂ content on the microstructure and upconversion luminescence of the samples was analyzed in detail. The results indicated that with the increase of PbF₂ content, the Ω₂ was almost the same and the ratios of red to green upconversion luminescence decreased in glass ceramics.     

Electrical conductivity studies in single and mixed alkali doped cobalt-borate glasses

The glasses of the type (Li₂O)_x-(CoO)_0.2-(B₂O₃)_0.8−x and (Li₂O)_0.2-(K₂O)_x-(CoO)_0.2-(B₂O₃)_0.6−x were prepared by melt quench technique and their non-crystallinity has been established by XRD studies. The glasses were investigated for room temperature density and dc electrical conductivity in the temperature range 300-550 K. Molar volumes were estimated from density data. Composition dependence of density and molar volume in both the sets of glasses has been discussed. Conductivity data has been analyzed in the light of Mott’s Small Polaron Hopping (SPH) Model and activation energies were determined. Variation of conductivity and activation energy with Li₂O content in single alkali glasses indicated change over conduction mechanism from predominantly electronic to ionic, at 0.4 mole fraction of Li₂O. In mixed alkali glasses, the conductivity has passed through minimum and activation energy has passed through maximum at x = 0.2. This has been attributed to the mixed alkali effect. It is for the first time that a change over of predominant conduction mechanism in lithium-cobalt-borate glasses and mixed alkali effect in lithium-potassium-cobalt-borate glasses has been observed. Various physical and polaron hopping parameters such as polaron hopping distance, polaron radius, polaron binding energy, polaron band width, polaron coupling constant, effective dielectric constant, density of states at Fermi level have been determined and discussed.     

The effect of composition on UV-vis-NIR spectra of iron doped glasses in the systems Na2O/MgO/SiO2 and Na2O/MgO/Al2O3/SiO2

Glasses with the compositions xNa₂O · 10MgO · (90 − x)SiO₂, 10Na₂O · xMgO · (90 − x)SiO₂, 5Na₂O · 15MgO · xAl₂O₃ · (80 − x)SiO₂, xNa₂O · 10MgO · 10Al₂O₃ · (80 − x)SiO₂, 10Na₂O · 10MgO · xAl₂O₃ · (80 − x)SiO₂, 10Na₂O · 5MgO · 10Al₂O₃ · (80 − x)SiO₂ were melted and studied using UV-vis-NIR spectroscopy in the wavenumber range from 5000 to 30 000 cm⁻¹. At [Al₂O₃] > [Na₂O], the UV-cut off is strongly shifted to smaller wavenumbers and the NIR peak at around 10 000 cm⁻¹ attributed to Fe²⁺ in sixfold coordination gets narrower. Furthermore, the intensity of the NIR peak at 5500 cm⁻¹ increases. This is explained by the incorporation of iron in the respective glass structures.     

Structure and electrical conductivity of new Li2O-CeO2-B2O3 glasses

Fourier transformation infrared spectra, density and DC electrical conductivity of 30Li₂O · xCeO₂⋅(70 − x)B₂O₃ glasses, where x ranged between 0 and 15 mol%, have been investigated. The results suggested that CeO₂ plays the role of network modifier up to 7.5 mol%. At higher concentrations it plays a dual role; where most of ceria plays the role of network former. The density was observed to increase with increasing CeO₂ content. The effect on density of the oxides in the glasses investigated is in the succession: B₂O₃ < Li₂O < CeO₂. Most of CeO₂ content was found to be associated with B₂O₃ network to convert BO₃ into B O₄⁻ units. The contribution of Li⁺ ions in the conduction process is much more than that due to small polarons. The conductivity of the glasses is mostly controlled by the Li⁺ ions concentration rather than the activation energy for CeO₂ > 5 mol%. Lower than 5 mol% CeO₂ the conductivity is controlled by both factors. The dependence of W on BO₄⁻ content supports the idea of ionic conduction in these glasses.     

Thermal diffusivity measurements on As-Te-Ga glasses by photo-thermal deflection technique: Composition dependence and topological thresholds

The thermal diffusivity (α) of As₂₀Te_80−xGa_x glasses (7.5 ? x ? 18.5) has been measured using photo-thermal deflection (PTD) technique. It is found that the thermal diffusivity is comparatively lower for As₂₀Te_80−xGa_x glasses, which is consistent with the memory type of electrical switching exhibited by these samples. Further, the thermal diffusivity of As₂₀Te_80−xGa_x glasses is found to increase with the incorporation of gallium initially (for x ? 9), which is consistent with the metallicity of the additive. This increase in α results in a maximum at the composition x = 9; beyond x = 9, a decrease is seen in α leading to a minimum at the composition x = 15. The observed composition dependence of thermal diffusivity of As₂₀Te_80−xGa_x glasses has been found to be similar to that of Al₂₀As_xTe_100−x glasses, based on which it is proposed that As₂₀Te_80−xGa_x glasses exhibit an extended stiffness transition with compositions x = 9 and x = 15 being its onset and completion, respectively. Also, the composition x = 17.5 at which a second maximum is seen in the thermal diffusivity has been identified to be the chemical threshold (CT) of the As₂₀Te_80−xGa_x glassy system, as at CT, the glass is configurationally closest to the crystalline state and the scattering of the diffusing thermal waves is minimal for the chemically ordered phase.     

Elasticity, thermal expansion and compressive behavior of Mg65Cu25Tb10 bulk metallic glass

The existence of special covalently bonded short-range ordering structures in a Mg₆₅Cu₂₅Tb₁₀ bulk metallic glass (BMG) is confirmed by thermal expansion and compression behavior. Under ambient conditions the linear thermal expansion coefficient obtained is almost constant in the glassy state with a value of 4.0 × 10⁻⁵ K⁻¹. By fitting the static equation of state at room temperature under ambient conditions we find the value for bulk modulus B of 48.7 GPa, which is in excellent agreement with the experimental study by pulse-echo techniques of 44.7 GPa. Unlike many bulk metallic glasses, such as Zr- and Pd-based, which bulk modulus is much larger than 100 GPa, the value B of Mg₆₅Cu₂₅Tb₁₀ BMG falls into the range of SiO₂ and fluorozirconate glass ZBLAN. Moreover, the elastic constant of the Mg₆₅Cu₂₅Tb₁₀ BMG is almost the same as those of ZBLAN. No evidence for the high-pressure phase transitions of the Mg₆₅Cu₂₅Tb₁₀ BMG has been found up to 31.19 GPa at room temperature.     

Effects of Nb on the formation of icosahedral quasicrystalline phase in Ti-rich Ti-Zr-Ni-Cu-Be glassy forming alloys

As-cast (Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈)_100−xNb_x (0 ? x ? 5) (Ф3) glassy forming alloys were investigated in order to clarify the role of Nb on the formation of icosahedral quasicrystalline phase (I-phase) in Ti-rich Ti-Zr-Ni-Cu-Be glassy system. It is found that an I-phase is formed in Ti-Zr-Ni-Cu-Be glassy alloy by addition of Nb element; however, the nucleation rate of I-phase increases, whereas the grain growth rate decreases with increasing Nb content. Moreover, with increasing Nb content, the thermal stability against crystallization increases, while the temperature range of stability of the I-phase decreases.     

Photoluminescence and optical absorption in glassy AsxSe1−x

The photoluminescence and optical absorption spectra in glassy As_xSe_1−x with 0.08 ? x ? 0.40 are essentially independent of x. The PL spectra peak at approximately half the optical gap and the exponential slopes of the optical absorption edges are all approximately 75 meV. For x > 0.4, the PL peaks shift to higher energies, the widths of the PL spectra increase, and there is a strong component to the optical absorption well below the optical gap. Comparisons with ESR experiments in the As_xS_1−x system suggest the possibility of two PL peaks. The second PL peak and the optical absorption below the optical band gap for x > 0.4 are attributed to the presence of As-As bonds.     

Nano- and micro-indentation studies on lithium borate-barium bismuth niobate glasses

The structure and mechanical properties of multifunctional lithium tetra-borate based glasses and glass-ceramics of the system (100 − x) Li₂B₄O₇₋x(BaO-Bi₂O₃-Nb₂O₅) with x = 10, 20 and 30 in molar ratio, have been characterized. Nano- and micro-indentation techniques were employed to evaluate the elastic modulus, hardness and toughness of the as-cast and annealed glasses. These were complemented with detailed structural investigations using X-ray diffraction, microscopy (optical, scanning electron and high resolution transmission electron microscopies) and nuclear magnetic resonance spectroscopy. These investigations reveal a smooth variation of the mechanical properties with composition except for the composition corresponding to x = 20. This deviation has been attributed to subtle changes in the glass-structure due to amorphous phase-separation and heat-treatment-assisted nano-crystallization.     

Calculation of phase diagrams in AlxIn1−xAs/InP,AsxSb1−xAl/InP and AlxIn1−xSb/InSb nano-film systems

The models for calculation of phase diagrams of semiconductor thin films with different substrates were proposed by considering the contributions of strain energy, the self-energy of misfit dislocations and surface energy to Gibbs free energy. The phase diagrams of the Al_xIn_1−xAs and As_xSb_1−xAl thin films grown on the InP (1 0 0) substrate, and the Al_xIn_1−xSb thin films grown on the InSb (1 0 0) substrate at various thicknesses were calculated. The calculated results indicate that when the thickness of film is less than 1 μm, the strain-induced zinc-blende phase appears, the region of this phase extends with decreasing of the layer thickness, and there is small effect of surface energies of liquid and solid phases on the phase diagrams.     

Glass formation ability and mechanical properties of Ti40Cu40Zr10Ni10 alloy

Melt-spun ribbon and bulk samples in cylindrical rod form with diameter ranging from 2 mm to 4 mm of Ti₄₀Cu₄₀Zr₁₀Ni₁₀ alloy were prepared by melt-spinning technique and copper mould casting method, respectively. The microstructure, thermal stability and mechanical properties of the bulk samples were investigated. A completely glassy single phase is formed in the 2 mm rod sample. Increasing the diameter of the rod samples resulted in the formation of CuTi crystalline phase in the 3 mm and 4 mm rod samples. The 2 mm single glassy rod sample exhibited a large supercooled liquid region ΔT_x = 58 K and γ = T_x/(T_g + T_l) is 0.390, which indicated that the alloy possessed a good glass-forming ability. The bulk samples also exhibited good mechanical properties. The 2 mm rod sample showed the highest yield strength of about 2086 MPa. The 3 mm rod sample not only showed high yield strength of about 2000 MPa, but also enhanced plastic strain of about 0.71%.     

Growth of InxGa1−xN quantum dots by nitridation of nano-alloyed droplet method using MOCVD

In_xGa_1−xN quantum dots (QDs) were grown on GaN/sapphire (0 0 0 1) substrates by employing nitridation of nano-alloyed droplet (NNAD) method using metal-organic chemical vapor deposition (MOCVD). In+Ga alloy droplets were initially formed by flowing the precursors TMIn and TMGa. Density of the In+Ga alloy droplets was increased with increasing precursors flow rate; however, the droplet size was scarcely changed in the range of about 100–200 nm. Two cases of In_xGa_1−xN QDs growth were investigated by varying the nitridation time and the growth temperature. It was observed that the In_xGa_1−xN QDs size can be easily changed by controlling the nitridation process at the temperature between 680 and 700 °C for the time of 5–30 min. Self-assembled In_xGa_1−xN QDs were successfully grown by employing NNAD method.