Studies of Er doped germanate-oxyfluoride and tellurium-germanate-oxyfluoride transparent glass-ceramics

An erbium doped germanate-oxyfluoride glass 60GeO₂ · 20PbO · 10PbF₂ · 10CdF₂ (GPOF) and a tellurium-germanate-oxyfluoride glass 30TeO₂ · 30GeO₂ · 20PbO · 10PbF₂ · 10CdF₂ (TGPOF) were prepared in the bulk form. By appropriate heat treatment of the as-prepared glasses above, transparent glass-ceramics were obtained with the formation of β-PbF₂ nanocrystals in the glass matrix confirmed by X-ray diffraction. Optical absorption and photoluminescence measurements were performed on as-prepared glass and glass-ceramics. The luminescence of Er³⁺ ions in transparent glass-ceramics revealed sub-band splitting generally seen in a crystal host. The intensity of red and near infrared luminescence significantly increased in transparent glass-ceramic compared to that in as-prepared glass. Two luminescence bands at 758 nm from ⁴F_7/2 → ⁴I_13/2 and at 817 nm from ²H_11/2 → ⁴I_13/2 transitions were observed from transparent glass-ceramic but cannot be seen from the corresponding as-prepared glass. These results are attributed to the change of ligand field of Er³⁺ ions and the decrease of effective phonon energy when Er³⁺ ions were incorporated into the precipitated β-PbF₂ nanocrystals.     

Thermomagnetic study of the amorphous cobalt-erbium borides Co80ErxB20−x (0 ? x ? 4)

Calorimetric, magnetic and X-ray diffraction measurements have been used to study the magnetic susceptibility and thermal stability of Co₈₀Er_xB_20−x with (0 ? x ? 4) amorphous ribbons. The compounds are found to crystallize in Co₂B and β-Co, after precipitation of the tetragonal Co₃B phase. The addition of erbium shifts up the crystallization temperature leading to the increase in the stability of the amorphous state. Magnetic susceptibility measurements show that the addition of erbium increases the Curie temperature and induces noncollinear magnetic behavior. This latter fact is explained on the basis of random local magnetic anisotropy related to the rare earth atoms in amorphous materials.     

Spectroscopic properties of Er-doped Na2O-Sb2O3-B2O3-SiO2 glasses

Spectroscopic properties of Er³⁺-doped Na₂O-Sb₂O₃-B₂O₃-SiO₂ glasses have been investigated for developing 1.5-μm broadband fiber amplifiers. An intense 1.5-μm near infrared emission with a broad full width at half maximum (FWHM) of 88 nm has been obtained for Er³⁺-doped 5Na₂O-20Sb₂O₃-35B₂O₃-40SiO₂ glass upon excitation with a 980 nm laser diode. The obtained emission cross-section of the ⁴I_13/2 → ⁴I_15/2 transition and the lifetime of the ⁴I_13/2 level of Er³⁺ ions are 6.8 × 10⁻²¹ cm² and 0.36 ms, respectively. It is noted that the product of the emission cross-section and the FWHM of the glass, σ_e × FWHM, is as great as 598.4 × 10⁻²¹ cm² nm, which is comparable or higher than that of Er³⁺-doped bismuth-based and tellurite-based glasses. These special optical properties encourage in identifying them as important materials for potential applications in high performance optics and optical communication networks.     

Energy transfer between Tm and Er ions in a TeO2-based glass pumped at diode laser wavelength

In this paper we investigate the energy transfer processes in Tm³⁺/Er³⁺ doped telluride glass pumped at the commercial diode laser pump wavelength ∼800 nm. Tailoring the rare-earths content in the glass matrix, seven main energy transfer channels within the doping range considered were identified. A 6-fold enhancement of the Er³⁺ visible frequency upconversion fluorescence at ∼660 nm is observed due to the inclusion of Tm³⁺ ions. This is evidence of the relevant contribution of the route Er₁(⁴I_11/2) + Er₂(⁴I_13/2) → Er₁(⁴I_15/2) + Er₂(⁴F_9/2) to the process. Energy migration among pumped ⁴I_9/2 level reducing the efficiency of the upconversion emission rate (³H_11/2, ⁴S_3/2, and ⁴F_9/2) is observed for Er³⁺ above 1.5 wt%. The rate equations regarding the observed energy transfer routes are determined and a qualitative analysis of the observed processes is reported.     

Optical properties of and concentration quenching in Bi2O3-B2O3-Ga2O3 glasses

Er₂O₃-doped Bi₂O₃-B₂O₃-Ga₂O₃ glasses were prepared by the conventional melt-quenching method, and the Er³⁺:⁴I_13/2 → ⁴I_15/2 fluorescence properties are studied for different Er³⁺ concentrations. when the Er₂O₃ concentration increases from 0.03 to 3.0 mol%, the measured lifetime of Er³⁺:⁴I_13/2 level decrease from 2.24 to 0.9 m s, and from 0.25 to 0.20 m s for the Er³⁺:⁴I_11/2 level. The fast energy migration among Er³⁺ ions cause the reduction of lifetime of the ⁴I_13/2 level, whereas the change in the ⁴I_11/2 level is mainly due to a cooperative upconversion process (⁴I_11/2, ⁴I_11/2) → (⁴F_7/2, ⁴I_15/2). Based on the dipole-dipole interaction theory, the interaction parameter, C_Er,Er, for the migration rate of Er³⁺:⁴I_13/2 ↔ ⁴I_13/2 was calculated to be 32 × 10⁻⁴⁰ cm⁶ s⁻¹.     

Transport property and structural characterization studies on (1 − x)[0.75AgI:0.25AgCl]:xTiO2 conducting composite electrolyte system

Transport property and structural investigation have been carried out on newly synthesized Ag⁺ ion conducting composite electrolyte system. The composite electrolyte system (1 − x)[0.75AgI:0.25AgCl]:xTiO₂, where 0 ? x ? 0.5 (in molar weight fraction) has been synthesized by melt quenching and annealing methods. The chemical compound TiO₂ (second phase dispersoid) dispersed in different compositions in a quenched (0.75AgI:0.25AgCl) mixed system/solid solution; this solid solution was used as a first phase host salt in place of AgI. The different preparation routes were adopted for the composite electrolyte system. Composition x = 0.1 exhibited highest conductivity at room temperature. The composite system 0.9[0.75AgI:0.25AgCl]:0.1TiO₂ was synthesized at different soaking times by melt quenching method. The system exhibited optimum conductivity at 20 min soaking time (σ_rt ≈ 1.4 × 10⁻³ S/cm). The ac conductivity has been measured from Z′-Z″ (Cole-Cole) complex impedance plots using impedance spectroscopic (IS) technique. The electrical conductivity as a function of temperature and frequency has been studied, and activation energy E_a, was calculated from Arrhenius plots for all compositions (0 ? x ? 0.5). The dc conductivity value has been evaluated from Log σ vs. log f plots. Structural characterization studies were carried out by X-ray diffraction (XRD) and differential thermal analysis (DSC) techniques.     

Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

Laser-induced crystallization of β′-RE2(MoO4)3 ferroelectrics (RE: Sm, Gd, Dy) in glasses and their surface morphologies

The glasses with the compositions of 21.25RE₂O₃-63.75MoO₃-15B₂O₃ (RE: Sm, Gd, Dy) were prepared and the formation of β′-RE₂(MoO₄)₃ ferroelectrics was confirmed in the crystallized glasses obtained through a conventional crystallization in an electric furnace. The features of the glass structure and crystallization behavior were clarified from measurements of Raman scattering spectra. Continuous-wave Nd:YAG laser with a wavelength of 1064 nm (laser power: 0.6-0.9 W, laser scanning speed: S = 1-16 μm/s) was irradiated to 10.625Sm₂O₃-10.625Gd₂O₃ (or Dy₂O₃)-63.75MoO₃-15B₂O₃ glasses, and the structural modification was induced at the glass surface. At the scanning speed of S = 10 μm/s, crystal lines consisting of β′-Gd_2−xSm_x(MoO₄)₃ or β′-Dy_2−xSm_x(MoO₄)₃ crystals were patterned on the glass surface. It was found that those crystal lines have the surface morphology with periodic bumps. At S = 1 μm/s, it was found that crystal lines consist of the mixture of paraelectric α-Gd_2−xSm_x(MoO₄)₃ and ferroelectric β′-Gd_2−xSm_x(MoO₄)₃ crystals, indicating the phase transformation from the β′ phase to the α phase during laser irradiation. Homogeneous crystal lines with β′-RE₂(MoO₄)₃ ferroelectrics have not been written in this study, but further research is continuing.     

Synthesis and Judd-Ofelt analysis of a sol-gel material doped with a Ln2(Benzoate)6(Phen)2 (Ln = Er/Yb) complex

In this work, we have prepared a sol-gel derived hybrid material directly doped with Er_1.4Yb_0.6(Benzoate)₆(Phen)₂ (Phen = 1,10-phenanthroline) complex, which was reported with intramolecular Yb-Er energy-transfer process in our previous work. The infrared (IR) spectra of the pure complex and hybrid gel material were investigated. The NIR photoluminescence (PL) spectrum of hybrid gel material shows strong characteristic emission of Er³⁺ with broad full width at half-maximum (FWHM) of 70 nm. Judd-Ofelt theory was used in order to analyze the optical properties of Er³⁺ ions in the hybrid gel material.     

Crystal growth and spectroscopic properties of erbium doped Lu2SiO5

A high optical quality erbium doped Lu₂SiO₅ single crystal has been grown by the Czochralski method. The distribution coefficient of Er³⁺ was measured to be ∼0.926. The absorption and emission spectra as well as the fluorescence decay curve of the excited state ⁴I_13/2 were measured at room temperature. The spectroscopic parameters were calculated using the Judd–Ofelt theory, and the J–O parameters Ω₂, Ω₄ and Ω₆ were found to be 4.451×10^-20, 1.614×10^-20 and 1.158×10^-20 cm², respectively. The room-temperature fluorescence lifetime of the Er³⁺⁴I_13/2→⁴I_15/2 transition was measured to be 7.74 ms. The absorption and emission cross-section as well as the gain cross-section in the eye-safe regime of 1400–1700 nm were also determined and discussed.     

Influence of heat treatment on spectroscopic properties of Er in multicomponent ZrF4-ZnF2-AlF3-YF3-MF2 (M = Ca, Sr, Ba) based glass

Er³⁺ doped multicomponent fluoride based glass was prepared. These precursor fluoride glass samples were then heated using different schedules. Crystalline phase particles were successfully precipitated in the multicomponent fluoride glass samples after heat treatment. The influence of heat treatment on the spectroscopic properties of Er³⁺ in multicomponent fluoride based glass samples were discussed. Small changes of the Judd-Ofelt parameters Ω_i (i = 2, 4, 6) were found in multicomponent fluoride glass samples before and after heat treatment compared to oxyfluoride telluride glass. Preparation conditions used to produce transparent multicomponent fluoride glass ceramics doped with rare-earth ions are discussed.     

Growth and spectroscopic characteristics of Er:YbVO4 crystal

A laser crystal Er³⁺:YbVO₄ has been grown by the Czochralski method with excellent quality. The rocking curve from the (0 0 4) diffraction plane of the as-grown Er³⁺:YbVO₄ crystal was measured and the full-width at half-maximum value was found to be 19.80 in. for the (0 0 4) face. The effective segregation coefficient of Er³⁺ was studied by X-ray fluorescence and the crystal structure was determined by means of X-ray diffraction analysis. The polarized absorption spectra and the fluorescence spectra of Er³⁺:YbVO₄ were measured at room temperature. The spectral parameters were calculated based on the Judd–Ofelt theory, and the intensity parameters Ω₂, Ω₄ and Ω₆ are found to be 5.50×10⁻²⁰, 1.96×10⁻²⁰ and 2.34×10⁻²⁰ cm², respectively. The emission cross-section has been calculated by the Fuechtbauer–Ladenbury method. The spectroscopic parameters of Er³⁺:YbVO₄ are compared with other typical laser hosts.     

Low-temperature RPCVD of Si,SiGe alloy,and Si1−yCy films on Si substrates using trisilane (Silcore)

Si homo-epitaxial growth by low-temperature reduced pressure chemical vapor deposition (RPCVD) using trisilane (Si₃H₈) has been investigated. The CVD growth of Si films from trisilane and silane on Si substrates are compared at temperatures between 500 and 950 °C. It is demonstrated that trisilane efficiency increases versus silane's one as the surface temperature decreases. Si epilayers from trisilane, with low surface roughness, are achieved at 600 and 550 °C with a growth rate equal to 12.4 and 4.3 nm min⁻¹, respectively. It is also shown that Si_1−xGe_x layers can be deposited using trisilane chemistry.     

Optical,structural investigations and band-gap bowing parameter of GaInN alloys

We have performed a detailed investigation of the photoluminescence features taken at 2 K on a series of Ga_xIn_1−xN alloys grown by metal-organic vapour-phase epitaxy through the whole composition range. The evolution of the photoluminescence lineshape of GaInN alloys in the indium-rich region is dominated by doping effects rather than by band-gap tailing effects correlated to existence of random chemical crystal inhomogeneities. The lineshape of the photoluminescence indicates a residual electron concentration of about 10¹⁸–10¹⁹ cm⁻³ in the bulk part of the epilayers. The value we get for the bowing parameter is b=2.8 eV.     

Crystal growth and characterization of two-leg spin ladder compounds: Sr14Cu24O41 and Sr2Ca12Cu24O41

Single crystals of Sr_14−xCa_xCu₂₄O₄₁ (x=0 and 12) are grown by the travelling solvent floating zone technique using an image furnace. The grown crystals are characterized for their single crystallinity by the X-ray and Neutron Laue method. The magnetic susceptibility measurements in Sr₁₄Cu₂₄O₄₁ show considerable anisotropy along the main crystallographic axes. Low-temperature specific heat measurement and DC susceptibility measurement in Ca-doped crystal showed antiferromagnetic ordering at 2.8 K at ambient pressure. High-pressure AC susceptibility measurement on Ca-doped crystal showed a sharp superconducting transition at 2 K under 40 kbars. T_c onset reached a maximum value of 9.9 K at 54 kbars. The bulk superconductivity of the sample is confirmed by the high-pressure AC calorimetry with T_c max=9.4 K and T_N=5 K at 56 kbars.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Development and characterizations of BaO-CaO-Al2O3-SiO2 glass-ceramic sealants for intermediate temperature solid oxide fuel cell application

Several compositions based on BaO-CaO-Al₂O₃-SiO₂ (BCAS) glass system have been studied in this investigation to see their applicability as sealant for solid oxide fuel cell (SOFC). The glasses as well as the corresponding glass-ceramics have been systematically characterized by differential thermal analysis, dilatometry, X-ray diffractometry, electron microscopy and impedance analysis to examine their suitability as sealant. While the glass transition temperature (T_g) determined from DTA are within 600-665 °C, the coefficient of thermal expansion (CTE) can be tailored between 9.5 and 13.0 × 10⁻⁶ K⁻¹. These glasses are found to be well adhered with metallic interconnects, such as commercial ferritic steel (Crofer22APU), at an optimum sealing temperature of 850 °C. The shrinkage behavior of the developed glasses in their pellet form has also been investigated. The resistivities of the glass-ceramics, as obtained from impedance analysis, are found to be within 10⁴-10⁶ Ω cm at 800 °C. Under sandwiched condition between two metals, some of the developed compositions are found to maintain this high resistivity even after 100 h of operation. One of the glass compositions has shown a low leak-rate of the order of ∼10⁻⁷ Pa m² s⁻¹.     

Deposition of mechanically hard amorphous carbon nitride films from decomposition of BrCN. Effects of substrate cooling and pulsed rf-bias voltage

Mechanically hard amorphous carbon nitride films were formed by applying a combination of radio frequency (RF) bias voltage to the substrate and the chemical vapor deposition process using the decomposition reaction of BrCN with the microwave discharge flow of Ar. Cooling water was circulated inside the substrate stage. The maximum hardness was (17 ± 1) GPa for the film prepared under the negative RF bias voltage, −V_RF, of 30 V. This hardness was nearly twice that of the film prepared without cooling, suggesting that substrate cooling was effective for suppressing the relaxation of the internal stress of the film due to the temperature rise during the application of the RF bias voltage. Under the continuous operation of the RF bias voltage, films cannot be formed for −V_RF > 40 V because of the sputtering by the bombardment of energetic Ar⁺. Then, the RF bias voltage was applied with a pulsed operation. By using this operation films were prepared in the range of −V_RF = 40-100 V. The hardness, (36 ± 10) GPa, was obtained for the film obtained under the conditions of −V_RF = 100 V, the pulse period of 1000 s, and the pulse-on time of 800 s. The observed hardness scattered largely for the different observation points within this film; a single observation point in that film showed the maximum hardness of 46 GPa. According to the IR spectra of the films, the three-dimensional C-N network structure was developed.     

Low-temperature/high-temperature AlN superlattice buffer layers for high-quality AlxGa1−xN on Si (1 1 1)

We present MOVPE-grown, high-quality Al_xGa_1−x N layers with Al content up to x=0.65 on Si (1 1 1) substrates. Crack-free layers with smooth surface and low defect density are obtained with optimized AlN-based seeding and buffer layers. High-temperature AlN seeding layers and (low temperature (LT)/high temperature (HT)) AlN-based superlattices (SLs) as buffer layers are efficient in reducing the dislocation density and in-plane residual strain. The crystalline quality of Al_xGa_1−xN was characterized by high-resolution X-ray diffraction (XRD). With optimized AlN-based seeding and SL buffer layers, best ω-FWHMs of the (0 0 0 2) reflection of 540 and 1400 arcsec for the (1 0 1¯ 0) reflection were achieved for a ∼1-μm-thick Al_0.1Ga_0.9N layer and 1010 and 1560 arcsec for the (0 0 0 2) and (1 0 1¯ 0) reflection of a ∼500-nm-thick Al_0.65Ga_0.35N layer. AFM and FE-SEM measurements were used to study the surface morphology and TEM cross-section measurements to determine the dislocation behaviour. With a high crystalline quality and good optical properties, Al_xGa_1−x N layers can be applied to grow electronic and optoelectronic device structures on silicon substrates in further investigations.     

Preparation and characterization of new fluorotellurite glasses for photonics application

Glasses based on (85 − x)TeO₂-xZnF₂-12PbO-3Nb₂O₅ (x = 0-40) system have been studied for the first time for fabricating mid-infrared optical fiber lasers. The thermal and optical properties including UV-Vis, Raman as well as FTIR spectra are reported. It is demonstrated that increasing the ZnF₂ concentration to 30 mol% significantly increased the thermal stability of the glass. Adding ZnF₂ also reduced the hydroxyl (OH) content of the glass resulting in lower optical absorption in the mid-infrared region, which is crucial for infrared laser applications. The glass absorption cut-off edge near 400 nm blue-shifts with increasing ZnF₂ addition. Raman spectra show a depolymerization of the glass network with increasing transformation of TeO₃₊₁ to TeO₃ structures.