Spectroscopic properties of Er-doped Na2O-Sb2O3-B2O3-SiO2 glasses

Spectroscopic properties of Er³⁺-doped Na₂O-Sb₂O₃-B₂O₃-SiO₂ glasses have been investigated for developing 1.5-μm broadband fiber amplifiers. An intense 1.5-μm near infrared emission with a broad full width at half maximum (FWHM) of 88 nm has been obtained for Er³⁺-doped 5Na₂O-20Sb₂O₃-35B₂O₃-40SiO₂ glass upon excitation with a 980 nm laser diode. The obtained emission cross-section of the ⁴I_13/2 → ⁴I_15/2 transition and the lifetime of the ⁴I_13/2 level of Er³⁺ ions are 6.8 × 10⁻²¹ cm² and 0.36 ms, respectively. It is noted that the product of the emission cross-section and the FWHM of the glass, σ_e × FWHM, is as great as 598.4 × 10⁻²¹ cm² nm, which is comparable or higher than that of Er³⁺-doped bismuth-based and tellurite-based glasses. These special optical properties encourage in identifying them as important materials for potential applications in high performance optics and optical communication networks.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Effect of BaO content on the sintering and physical properties of BaO-B2O3-SiO2 glasses

A BaO-B₂O₃-SiO₂ glass system was chosen as a candidate composition for the application to Pb-free low temperature sinterable glass. The effect of BaO content on the crystallization, sintering behavior, and properties of the glasses was examined. Both the glass transition temperature and crystallization temperature decreased as the BaO content increased. Crystallization easily occurred during sintering with a BaO content of more than 50 mol%, which effectively inhibited the over-firing phenomenon. The dielectric characteristics and thermal expansion coefficient of the glasses were examined and the results were explained on the basis of the crystallization and densification of the specimens.     

Crystallization processes of Li2O-Ga2O3-SiO2-NiO system glasses

Crystallization processes of Li₂O-Ga₂O₃-SiO₂-NiO system glasses have been studied by X-ray diffraction, differential calorimetry and optical absorption. Transparent glass-ceramic containing LiGa₅O₈:Ni²⁺ as the sole crystalline phase has been obtained from glass with the composition of 13Li₂O-23Ga₂O₃-64SiO₂-0.1NiO (in mol%) by the heat treatment in the temperature range from 923 to 953 K. It was revealed that the specific surface area of samples enhances crystallization of LiGaSi₂O₆ but obstructed that of LiGa₅O₈. LiGa₅O₈ grew to nano-sized crystallites dispersed in the glass matrices and did not affect the transparency seriously. In contrast, LiGaSi₂O₆ grew to crystallites with diameters more than 100 nm on the surface and made the glasses opaque. Optical absorption measurements revealed that doped Ni²⁺ occupied five-folded trigonal bipyramidal sites in the as-quenched glass matrices but six-folded octahedral sites of precipitated LiGa₅O₈ in the glass-ceramics. It was confirmed that transparent glass-ceramic containing Ni²⁺:LiGa₅O₈ was effectively obtained by the heat treatment at a temperature of 953 K for 10 h.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.     

Crystallization of monoclinic WO3 in tungstate fluorophosphate glasses

Tungstate fluorophosphate glass compositions with high WO₃ concentration were prepared in the ternary system (80−0.8x)NaPO₃-(20−0.2x)BaF₂-xWO₃ with x = 40,50 and 60 mol%. Transparency decreases as WO₃ concentration increases but can be improved by addition of oxidizing systems such as CeO₂ or Sb₂O₃/NaNO₃. Characterizations by thermal analysis (DSC) point out that an increase in the amount of WO₃ results in a higher glass transition temperature. In addition, such compositions are very stable against devitrification since samples containing 40% and 50% of WO₃ donot even exhibit the expected crystallization event. In these samples, the stability against crystallization decreases with the WO₃ content and vitreous sample containing 60% of WO₃ exhibits an endothermic event around 620 °C due to crystallization of monoclinic WO₃ phase. In these glasses, it was shown that the nucleation stage can be induced by thermal-treatment when external nucleating agents such as Ti or Sb are used. Finally, gold-doped samples exhibit a higher crystallization tendency and monoclinic WO₃ phase can be grown in such glasses.     

A study of nonlinear optical properties in Bi2O3-WO3-TeO2 glasses

A series of bismuth tungsten tellurite glasses were prepared and their densities, linear refractive indices and transmission spectra were measured. The optical bandgaps E_opt and Urbach energies E_e of glasses were obtained from ultraviolet absorption edges. Both the optical gap (E_opt) and the band tail (E_e) are behaving oppositely. As the value of E_opt decreases with increasing WO₃ content, the degree of disorder increases which causes more defects or localized states resulting in deep localized in the bandgap with the tailing increased. Z-scan technique was carried out to investigate the third-order nonlinear optical properties of Bi₂O₃-WO₃-TeO₂ glasses. The third-order optical nonlinearity increases with decreasing the optical bandgap E_opt, since a increase of WO₃ content can provide the non-bridging oxygen ion content.     

Polyvinylidene fluoride-hexafluoropropylene (PVdF-HFP)-based composite polymer electrolyte containing LiPF3(CF3CF2)3

This paper describes the preparation and characterization of lithium fluoroalkylphosphate-containing composite polymer electrolyte based on a polyvinylidene fluoride-hexafluoropropylene (PVdF-HFP) matrix. A mixture of ethylene carbonate and diethyl carbonate was used as a plasticizing agent and nanoscopic Al₂O₃ as a filler. The membranes were characterized by ac impedance, SEM, DSC, FTIR and fluorescence. An electrolyte with 2.5 wt% Al₂O₃ exhibited a conductivity of 9.8 × 10⁻⁴ S cm⁻¹ at ambient temperature. It was found that filler contents above 2.5 wt% rendered the membranes less conducting.     

Effect of P2O5 on the early stage crystallization of K-fluorrichterite glass-ceramics

The addition of 2 mol% P₂O₅ to stoichiometric K-fluorrichterite (KNaCaMg₅Si₈O₂₂F₂, KFR) has been reported to enhance the mechanical properties and improve the in vitro biocompatibility of this glass-ceramic by promoting the formation of enstatite and fluorapatite (FA). Here, the effect of further increasing the P₂O₅ concentration on phase evolution of KFR has been investigated. XRD data showed that mica crystallized in samples with 4 and 5 mol% P₂O₅ (GP4 and GP5, respectively) at 650 °C, but no diopside was detected at higher temperatures, in contrast with the general phase evolution in KFR based glass-ceramics. More importantly, however, the addition of ?4 mol% P₂O₅ induced phase separation of the glass into a silica glass matrix and phosphate rich droplets prior to crystallization. EDS traces taken from samples heat-treated at 600 °C, revealed that the silica glass matrix was deficient in Mg and unlikely to be the host for crystallization of mica. Conversely, the P₂O₅ rich regions contained excess Mg and were considered to be the host for the formation of mica and FA.     

Studies of Er doped germanate-oxyfluoride and tellurium-germanate-oxyfluoride transparent glass-ceramics

An erbium doped germanate-oxyfluoride glass 60GeO₂ · 20PbO · 10PbF₂ · 10CdF₂ (GPOF) and a tellurium-germanate-oxyfluoride glass 30TeO₂ · 30GeO₂ · 20PbO · 10PbF₂ · 10CdF₂ (TGPOF) were prepared in the bulk form. By appropriate heat treatment of the as-prepared glasses above, transparent glass-ceramics were obtained with the formation of β-PbF₂ nanocrystals in the glass matrix confirmed by X-ray diffraction. Optical absorption and photoluminescence measurements were performed on as-prepared glass and glass-ceramics. The luminescence of Er³⁺ ions in transparent glass-ceramics revealed sub-band splitting generally seen in a crystal host. The intensity of red and near infrared luminescence significantly increased in transparent glass-ceramic compared to that in as-prepared glass. Two luminescence bands at 758 nm from ⁴F_7/2 → ⁴I_13/2 and at 817 nm from ²H_11/2 → ⁴I_13/2 transitions were observed from transparent glass-ceramic but cannot be seen from the corresponding as-prepared glass. These results are attributed to the change of ligand field of Er³⁺ ions and the decrease of effective phonon energy when Er³⁺ ions were incorporated into the precipitated β-PbF₂ nanocrystals.     

Effect of P2O5 content in two series of soda lime phosphosilicate glasses on structure and properties - Part II: Physical properties

The effect of the variation in phosphate (P₂O₅) content on the properties of two series of bioactive glasses in the quaternary system SiO₂-Na₂O-CaO-P₂O₅ was studied. The first series (I) was a simple substitution of P₂O₅ for SiO₂ keeping the Na₂O:CaO ratio fixed (1:0.87). The second series (II) was designed to ensure charge neutrality in the orthophosphate (), therefore as P₂O₅ was added the Na₂O and CaO content was varied to provide sufficient Na⁺ and Ca²⁺ cations to charge balance the orthophosphate present. Network connectivity’s of the glasses were calculated, and densities and thermal expansion coefficients predicted using the Appen and Doweidar models, respectively. Theoretical densities were measured using the Archimedes principle. Characteristic temperatures, namely the glass transition temperature, T_g, and crystallization temperatures, T_x, were obtained using differential analysis (DTA). Two crystallization exotherms were observed for both glass series (T_xi and T_xii). Both T_g and T_x decreased with P₂O₅ addition for both series. The working range of the glasses, T_x-T_g was shown to increase to a maximum at around 4 mol% P₂O₅ then decrease at higher P₂O₅ contents for both series. Thermal expansion coefficients were measured using dilatometry increasing with P₂O₅ addition and showed good agreement with the Appen values. Dilatometric softening points, T_s, were also measured, which increased with P₂O₅ addition. X-ray diffraction (XRD) was performed on the glasses to confirm their amorphous nature. The glass containing 9.25 mol% P₂O₅ from series I exhibited well-defined peaks on the XRD trace, indicating the presence of a crystalline phase.     

Coordination and optical attenuation of TiO2-SiO2 glass by electron energy loss spectroscopy

Electron energy loss spectroscopy (EELS) techniques have been applied to investigate both the coordination and optical attenuation of TiO₂-SiO₂ glass. The coordination was determined from the electron energy loss near edge fine structure (ELNES) of Ti L_2,3-edges, and the results show that Ti ions substitute for Si ions in the tetrahedral coordinated sites. The optical attenuation of the glass was obtained from low energy loss of EELS data through Kramers-Kronig analysis, and the results show that Ti-doped silica has an absorption edge near 4.0 eV.     

Effects of Li replacement on the nucleation, crystallization and microstructure of Li2O-Al2O3-SiO2 glass

The Li replacement including the Li₂O replaced by other oxides and the expensive Li₂CO₃ replaced by low-cost spodumene mineral was studied to lower the product cost of (Li₂O-Al₂O₃-SiO₂, LAS) glass ceramic, and the effects of Li replacement on the nucleation, crystallization and microstructure of LAS glass were investigated by the differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Li₂O replacement increases the crystallization activation energy, lowers the crystal growth, and increases the nucleation and crystallization temperature by restraining the formation of crystalline phases. The Li₂CO₃ replacement decreases the crystallization activation energy, promotes the crystal growth, without affecting the nucleation, and lowers the crystallization temperature by adding some beneficial compositions with mixed alkali effect.     

Plasma etching of As2S3 films for optical waveguides

Chalcogenide glasses are good candidate materials for ultra-fast non-linear optic devices. In this work, we present the photolithographic process and the plasma etching of arsenic tri-sulphide (As₂S₃) film. The films were deposited on thermally oxidized silicon substrates by ultra-fast pulsed laser deposition. To protect As₂S₃ film from photo-resist developer, thin resist layer ∼100-200 nm was remained on the UV exposed area by controlling resist development time. After removing the protective layer in oxygen plasma, As₂S₃ waveguides were patterned in inductively coupled plasma reactive ion etching (ICP-RIE) system using CF₄-O₂ gas mixture. We investigated the etch rate and the etch selectivity to photo-resist of As₂S₃ as a function of bias power, induction power, operating pressure, and gas flow rate ratio of CF₄ and O₂. The film is mainly etched by the chemical reaction with fluorine radicals. The content of oxygen in the plasma determines the etched sidewall profiles and nearly vertical profile was obtained at high oxygen content plasma.     

Optical properties of the optical fiber containing Co doped ZnO-Al2O3-SiO2 glass-ceramics

Optical characteristics of silica glass optical fibers containing Co²⁺ doped ZnO-Al₂O₃-SiO₂ (ZAS) glass-ceramics prepared by slurry-doping method were investigated. The absorption and emission bands of the fibers were found to be originated from the tetrahedral Co²⁺ in ZnAl₂O₄ crystals in ZAS glass-ceramics particles embedded in the core of the fibers. The crystal field strength of the Co²⁺ ions in the optical fiber was found to be smaller than that of the Co²⁺ ions in the bulk ZAS glass-ceramics.     

Development and characterizations of BaO-CaO-Al2O3-SiO2 glass-ceramic sealants for intermediate temperature solid oxide fuel cell application

Several compositions based on BaO-CaO-Al₂O₃-SiO₂ (BCAS) glass system have been studied in this investigation to see their applicability as sealant for solid oxide fuel cell (SOFC). The glasses as well as the corresponding glass-ceramics have been systematically characterized by differential thermal analysis, dilatometry, X-ray diffractometry, electron microscopy and impedance analysis to examine their suitability as sealant. While the glass transition temperature (T_g) determined from DTA are within 600-665 °C, the coefficient of thermal expansion (CTE) can be tailored between 9.5 and 13.0 × 10⁻⁶ K⁻¹. These glasses are found to be well adhered with metallic interconnects, such as commercial ferritic steel (Crofer22APU), at an optimum sealing temperature of 850 °C. The shrinkage behavior of the developed glasses in their pellet form has also been investigated. The resistivities of the glass-ceramics, as obtained from impedance analysis, are found to be within 10⁴-10⁶ Ω cm at 800 °C. Under sandwiched condition between two metals, some of the developed compositions are found to maintain this high resistivity even after 100 h of operation. One of the glass compositions has shown a low leak-rate of the order of ∼10⁻⁷ Pa m² s⁻¹.     

Optical properties of and concentration quenching in Bi2O3-B2O3-Ga2O3 glasses

Er₂O₃-doped Bi₂O₃-B₂O₃-Ga₂O₃ glasses were prepared by the conventional melt-quenching method, and the Er³⁺:⁴I_13/2 → ⁴I_15/2 fluorescence properties are studied for different Er³⁺ concentrations. when the Er₂O₃ concentration increases from 0.03 to 3.0 mol%, the measured lifetime of Er³⁺:⁴I_13/2 level decrease from 2.24 to 0.9 m s, and from 0.25 to 0.20 m s for the Er³⁺:⁴I_11/2 level. The fast energy migration among Er³⁺ ions cause the reduction of lifetime of the ⁴I_13/2 level, whereas the change in the ⁴I_11/2 level is mainly due to a cooperative upconversion process (⁴I_11/2, ⁴I_11/2) → (⁴F_7/2, ⁴I_15/2). Based on the dipole-dipole interaction theory, the interaction parameter, C_Er,Er, for the migration rate of Er³⁺:⁴I_13/2 ↔ ⁴I_13/2 was calculated to be 32 × 10⁻⁴⁰ cm⁶ s⁻¹.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Remark on the optical gap in ZnO-Bi2O3-TeO2 glasses

Four ZnO-Bi₂O₃-TeO₂ glasses were prepared from high purity (4N5) oxides. From measurements of the optical transmission on very thin bulk samples the optical gap was determined at around 3.55 eV for the glasses studied. The temperature dependence of the optical gap was also determined from the room temperature close up to 500 K. Preliminary Raman scattering measurements indicate that with a decrease in TeO₂ content, TeO₄ trigonal bipyramid transformation proceeds into TeO₃ trigonal pyramids.     

Properties characterization of the Cu68.5Ni12P19.5 alloy at elevated temperatures

The Cu_68.5Ni₁₂P_19.5 alloy was cast into the ribbons using melt spinning (23 m/s). The amorphous ribbon in the as-cast state was investigated by differential thermal analysis (DTA), dynamic mechanical analysis (DMA), resistivity measurements and X-ray diffraction ‘in situ’ at different temperatures. The work presents attempts to find correlation between the changes of the mechanical properties presented by DMA cycles and during the other tests. The measurements of the relative resistivity R/R₀ versus temperature for repeated heating and cooling cycles to different temperatures show changes of the temperature coefficient of resistivity (TCR) indicating reversible and irreversible transformations in the studied alloy.