Hydroxypropyl methylcellulose based cephalexin extended release tablets: influence of tablet formulation,hardness and storage on in vitro release kinetics

The object of this study was to develop hydroxypropyl methylcellulose (HPMC) based cephalexin extended release tablet, which can release the drug for six hours in predetermined rate. Twenty-one batches of cephalexin tablets were prepared by changing various physical and chemical parameters, in order to get required theoretical release profile. The influences of HPMC, microcrystalline cellulose powder (MCCP), granulation technique, wetting agent and tablet hardness on cephalexin release from HPMC based extended release tablets were studied. The formulated tablets were also characterized by physical and chemical parameters. The dissolution results showed that a higher amount of HPMC in tablet composition resulted in reduced drug release. Addition of MCCP resulted in faster drug release. Tablets prepared by dry granulation was released the drug slowly than the same prepared with a wet granulation technique. Addition of wetting agent in the tablets prepared with dry granulation technique showed slower release. An increase in tablet hardness resulted in faster drug release. Tablets prepared with a wet granulation technique and having a composition of 9.3% w/w HPMC with a hardness of 10-12 kg/cm(2) gave predicted release for 6 h. The in vitro release data was well fit in to Higuchi and Korsmeyer-Peppas model. Physical and chemical parameters of all formulated tablets were within acceptable limits. One batch among formulated twenty-one batches was successful and showed required theoretical release. The effect of storage on in vitro release and physicochemical parameters of successful batch was studied and was found to be in acceptable limits.     

Properties of gastroretentive sustained release tablets prepared by combination of melt/sublimation actions of L-menthol and penetration of molten polymers into tablets

A novel floating sustained release tablet having a cavity in the center was developed by utilizing the physicochemical properties of L-menthol and the penetration of molten hydrophobic polymer into tablets. A dry-coated tablet containing famotidine as a model drug in outer layer was prepared with a L-menthol core by direct compression. The tablet was placed in an oven at 80°C to remove the L-menthol core from tablet. The resulting tablet was then immersed in the molten hydrophobic polymers at 90°C. The buoyancy and drug release properties of tablets were investigated using United States Pharmacopeia (USP) 32 Apparatus 2 (paddle 100 rpm) and 900 ml of 0.01 N HCl. The L-menthol core in tablets disappeared completely through pathways in the outer layer with no drug outflows when placed in an oven for 90 min, resulting in a formation of a hollow tablet. The hollow tablets floated on the dissolution media for a short time and the drug release was rapid due to the disintegration of tablet. When the hollow tablets were immersed in molten hydrophobic polymers for 1 min, the rapid drug release was drastically retarded due to a formation of wax matrices within the shell of tablets and the tablets floated on the media for at least 6 h. When Lubri wax? was used as a polymer, the tablets showed the slowest sustained release. On the other hand, faster sustained release properties were obtained by using glyceryl monostearate (GMS) due to its low hydrophobic nature. The results obtained in this study suggested that the drug release rate from floating tablets could be controlled by both the choice of hydrophobic polymer and the combined use of hydrophobic polymers.     

Bilayer tablets of atorvastatin calcium and nicotinic acid: formulation and evaluation

The objective of the study is to formulate bilayer tablets consisting of atorvastatin calcium (AT) as an immediate release layer and nicotinic acid (NA) as an extended release layer. The immediate release layer was prepared using super disintegrant croscarmellose sodium and extended release layer using hydroxypropylmethyl cellulose (HPMC K100M). Both the matrix and bilayer tablets were evaluated for hardness, friability, weight variation, thickness, and drug content uniformity and subjected to in vitro drug release studies. The amount of AT and NA released at different time intervals were estimated by HPLC method. The bilayer tablets showed no significant change either in physical appearance, drug content or in dissolution pattern after storing at 40 degrees C/75% relative humiding (RH) for 3 months. The release of the drug from the tablet was influenced by the polymer content and it was much evident from thermogravimetry/differential thermal analysis (TG/DTA) analysis. The results indicated that the bilayer tablets could be a potential dosage form for delivering AT and NA.     

Formulation approach for nicorandil pulsatile release tablet

The purpose of this study was to obtain a nicorandil pulsatile release tablet that has a well-regulated release lag time. When nicorandil is used as an antiangina drug, administration time control is important. A pulsatile release tablet is one of the effective approaches to modified release to reduce daily administration frequency. In this study, a pulsatile release tablet of nicorandil was formulated by fumaric acid dry coating around the core tablet including nicorandil. The model tablets, which had different content ratios of excipients in the dry-coating layer, were characterized by a dissolution test. The results showed that the release lag time was generated with fast release profiles. Various lag time controls of tablets were achieved, from 60 to 310 min on average, by variation of outer layer composition. From an analysis of the relation between lag times and outer layer composition, the key ingredient for prolongation of lag time was found to be fumaric acid. To analyze the lag time generation mechanism, water penetration for tablet was measured. The results indicated that the penetration depth was proportionate to the square root of time and the lag time formation mechanism was simple water penetration through the matrix of fumaric acid to the tablet core. The results also showed that the Washburn equation could be used to design the lag time of the pulsatile release tablet in this study. In conclusion, novel release control technology using fumaric acid was appropriate to obtain a nicorandil pulsatile release tablet that has well regulated lag time.     

Formulation and optimization of orally disintegrating tablets of sumatriptan succinate

The aims of the present research were to mask the intensely bitter taste of sumatriptan succinate and to formulate orally disintegrating tablets (ODTs) of the taste masked drug. Taste masking was performed by coating sumatriptan succinate with Eudragit EPO using spray drying technique. The resultant microspheres were evaluated for thermal analysis, yield, particle size, entrapment efficiency and in vitro taste masking. The tablets were formulated by mixing the taste masked microspheres with different types and concentrations of superdisintegrants and compressed using direct compression method followed by sublimation technique. The prepared tablets were evaluated for weight variation, thickness, hardness, friability, drug content, water content, in vitro disintegration time and in vitro drug release. All the tablet formulations disintegrated in vitro within 37-410 s. The optimized formulation containing 5% Kollidon CL-SF released more than 90% of the drug within 15 min and the release was comparable to that of commercial product (Suminat?). In human volunteers, the optimized formulation was found to have a pleasant taste and mouth feel and disintegrated in the oral cavity within 41 s. The optimized formulation was found to be stable and bioequivalent with Suminat?.     

In vitro evaluation of mucoadhesive vaginal tablets of antifungal drugs prepared with thiolated polymer and development of a new dissolution technique for vaginal formulations

The main objective of this work was to develop antifungal matrix tablet for vaginal applications using mucoadhesive thiolated polymer. Econazole nitrate (EN) and miconazole nitrate (MN) were used as antifungal drugs to prepare the vaginal tablet formulations. Thiolated poly(acrylic acid)-cysteine (PAA-Cys) conjugate was synthesized by the covalent attachment of L-cysteine to PAA with the formation of amide bonds between the primary amino group of L-cysteine and the carboxylic acid group of the polymer. Vaginal mucoadhesive matrix tablets were prepared by direct compression technique. The investigation focused on the influence of modified polymer on water uptake behavior, mucoadhesive property and release rate of drug. Thiolated polymer increased the water uptake ratio and mucoadhesive property of the formulations. A new simple dissolution technique was developed to simulate the vaginal environment for the evaluation of release behavior of vaginal tablets. In this technique, daily production amount and rate of the vaginal fluid was used without any rotational movement. The drug release was found to be slower from PAA-Cys compared to that from PAA formulations. The similarity study results confirmed that the difference in particle size of EN and MN did not affect their release profile. The release process was described by plotting the fraction released drug versus time and n fitting data to the simple exponential model: M(t)/M(∞)=kt(n). The release kinetics were determined as Super Case II for all the formulations prepared with PAA or PAA-Cys. According to these results the mucoadhesive vaginal tablet formulations prepared with PAA-Cys represent good example for delivery systems which prolong the residence time of drugs at the vaginal mucosal surface.     

Design and preparation of pulsatile release tablet as a new oral drug delivery system.

To achieve time-controlled or site specific delivery of a drug in the gastrointestinal tract, an orally applicable pulsatile drug release system with the dry-coated tablet form was developed. The system consisted of a less water permeable outer shell and a swellable core tablet; from such a system, the drug was expected to be rapidly released after a certain period of time on the basis of time-controlled disintegration mechanism. Various model disks of outer shell, consisting of hydrogenated castor oil and polyethyleneglycol 6000, were tested for their water penetration rate. The experimental results showed that water penetration proceeded obeying the boundary retreating mechanism, so that the lag time of the system could be controlled by changing either the thickness or the composition of the outer shell. The swelling force of various commercially available disintegrants was quantitatively compared, and it was found that carboxymethylcellulose calcium was the preferable disintegrant to be used for the core tablet. On the basis of the results of a series of fundamental studies, various pulsatile release tablets of isoniazide with different lag times were designed. In the in vitro dissolution test, typical pulsatile release was achieved for all the tablets prepared, and a good correlation was found between the observed lag time and the estimated lag time calculated from an empirical equation deduced from the thickness and polyethyleneglycol 6000 content of the outer shell.     

Design and in vitro evaluation of zidovudine oral controlled release tablets prepared using hydroxypropyl methylcellulose

Oral controlled release matrix tablets of zidovudine were prepared using different proportions and different viscosity grades of hydroxypropyl methylcellulose. The effect of various formulation factors like polymer proportion, polymer viscosity and compression force on the in vitro release of drug were studied. In vitro release studies were carried out using United States Pharmacopeia (USP) type 1 apparatus (basket method) in 900 ml of pH 6.8 phosphate buffer at 100 rpm. The release kinetics were analyzed using Zero-order model equation, Higuchi's square-root equation and Ritger-Peppas' empirical equation. Compatibility of drug with various formulations excipients used was studied. In vitro release studies revealed that the release rate decreased with increase in polymer proportion and viscosity grade. Increase in compression force was found to decrease the rate of drug release. Matrix tablets containing 10% hydroxypropyl methylcellulose (HPMC) 4000 cps were found to show a good initial drug release of 21% in the first hour and extended the release upto 16 h. Matrix tablets containing 20% HPMC 4000 cps and 10% HPMC 15000 cps showed a first hour release of 18% and extended the release upto 20 h. Mathematical analysis of the release kinetics indicated that the nature of drug release from the matrix tablets followed non-Fickian or anomalous release. No incompatibility was observed between the drug and excipients used in the formulation of matrix tablets. The developed controlled release matrix tablets of zidovudine, with good initial release (17-25% in first hour) and which extend the release upto 16-20 h, can overcome the disadvantages of conventional tablets of zidovudine.     

hGH release from directly compressed hGH-PLGA biodegradable implantable tablets: Influence of physicomechanical factors

The incidence of compression conditions, porosity and polymer degradation on human growth hormone (hGH) release from PLGA implantable tablets was evaluated with the aim of gaining insight in the mechanism involved in drug delivery from biodegradable matrices. Tablets elaborated by direct compression of hGH with PLGA, applying various compression forces for different times, kept the integrity and the stability of the hormone. Tablet dimensions, viscoelastic properties, glass to rubber transition temperature (T_g), PLGA degradation rate and water uptake were analyzed in the freshly prepared implantable tablets as well as at several times during release test in phosphate buffer pH 7.4. Placebo tablets were also prepared to evaluate the incidence of hGH on the physicomechanical properties of the device and PLGA degradation rate. Porosity remarkably determined the amount of hGH released, through an effect on the easiness of water penetration in the tablet and on the beginning of PLGA degradation. The decrease in PLGA molecular weight during the first days in the release medium, despite of being minor, significantly conditioned hGH release rate. The more dramatic changes in PLGA molecular weight observed after 20 days in the release medium notably reduced the T_g and the viscous and elastic moduli of the tablets. The overall analysis of the events underwent by the tablets in contact with the aqueous medium was used to explain the drug release profile and may help to optimize the design of the PLGA-based implantable tablets as peptidic drug delivery systems.     

Influence of internal structure on kinetics of drug release from wax matrix tablets

To examine the influence of the internal structure of a wax matrix tablet on in vitro drug release, the release rates of several tablets consisting of various proportions of drug and wax were compared with the water penetration rates from the compressed and lateral surfaces of the tablets. The penetration rates from the lateral surface were found to be much faster than those from the compressed surface in all cases. A theoretical equation involving a two-dissolving-direction was derived on the basis of the boundary retreating concept. The retreating rate constants deduced from the dissolution results were well coincident with the values directly determined by the needle penetration method, suggesting good applicability of the proposed equation. The results suggest that the tortuosity of the water channels created in a tablet during dissolution is generally smaller in the horizontal direction than that in the vertical direction. This would be caused by the drug particles or granules being elongated in the horizontal direction by compression.     

Absorption of diltiazem in beagle dog from pulsatile release tablet.

An orally applicable pulsatile drug delivery system in dry-coated tablet form was prepared using diltiazem hydrochloride as the model drug, and a polyvinyl chloride-hydrogenated castor oil-polyethyleneglycol mixture as the outer shell of the tablet. In vitro drug release from the prepared tablet exhibited a typical pulsatile pattern with a 7 h lag phase (non-drug release period). This dosage form was orally administered to three beagle dogs under non-fasting and fasting conditions, and the plasma concentration level of diltiazem was determined according to time after administration. The result of the in vivo study in non-fasting dogs suggested that the drug could be released in the gastrointestinal tract as in the in vitro test. However, under the fasting condition, a large difference in the plasma concentration profile was found, suggesting that the disintegration time of the tablet tended to be influenced by the feeding condition of subject.     

Relationship between diffusivity of water molecules inside hydrating tablets and their drug release behavior elucidated by magnetic resonance imaging

We reported previously that sustained release matrix tablets showed zero-order drug release without being affected by pH change. To understand drug release mechanisms more fully, we monitored the swelling and erosion of hydrating tablets using magnetic resonance imaging (MRI). Three different types of tablets comprised of polyion complex-forming materials and a hydroxypropyl methylcellulose (HPMC) were used. Proton density- and diffusion-weighted images of the hydrating tablets were acquired at intervals. Furthermore, apparent self-diffusion coefficient maps were generated from diffusion-weighted imaging to evaluate the state of hydrating tablets. Our findings indicated that water penetration into polyion complex tablets was faster than that into HPMC matrix tablets. In polyion complex tablets, water molecules were dispersed homogeneously and their diffusivity was relatively high, whereas in HPMC matrix tablets, water molecule movement was tightly restricted within the gel. An optimal tablet formulation determined in a previous study had water molecule penetration and diffusivity properties that appeared intermediate to those of polyion complex and HPMC matrix tablets; water molecules were capable of penetrating throughout the tablets and relatively high diffusivity was similar to that in the polyion complex tablet, whereas like the HPMC matrix tablet, it was well swollen. This study succeeded in characterizing the tablet hydration process. MRI provides profound insight into the state of water molecules in hydrating tablets; thus, it is a useful tool for understanding drug release mechanisms at a molecular level.     

Formulation of Risperidone as Self-Nanoemulsifying Drug Delivery System in Form of Effervescent Tablets

Risperidone is an atypical antipsychotic drug used to treat schizophrenia. This study aims to formulate risperidone as effervescent tablets to improve patient compliance. Different nanoemulsion combinations were loaded with risperidone to improve its poor water solubility then adsorbed on Aeroperl. The formula showing highest drug dissolution was formulated as effervescent tablets. Factorial design was applied for different tablet formulation variables and the prepared formulae were tested for different criteria in comparison with their corresponding formulae containing drug without nanoemulsion formulation. Statistical analysis was used to determine the most desirable tablet formula considering its Carr index, effervescence time, and drug release.     

Controlled release from directly compressible theophylline buccal tablets

The aim of the current study was the development of theophylline buccal adhesive tablets using direct compression. Buccal adhesive formulations were developed using a water soluble resin with various combinations of mucoadhesive polymers. The prepared theophylline tablets were evaluated for tensile strength, swelling capacity and ex vivo mucoadhesion performance. Ex vivo mucoadhesion was assessed using porcine gingival tissue and the peak detachment forces were found to be suitable for a buccal adhesive tablet with a maximum of 1.5 N approximately. The effect of formulation composition on the release pattern was also investigated. Most formulations showed theophylline controlled release profiles depended on the grade and polymer ratio. The release mechanisms were found to fit Peppas’ kinetic model over a period of 5 h. In general the majority of the developed formulations presented suitable adhesion and controlled drug release.     

Zero-order release formulations using a novel cellulose ester

New carboxymethylcellulose esters were developed with useful properties for oral dosage forms in drug delivery. Normally, commercial cellulose esters are used as the major excipients in oral dosage forms as a coating or a membrane. In applications involving compression tablets, cellulose esters are usually mixed with other more hydrophilic matrix components to facilitate dissolution of the active. In the present study, novel cellulose esters were single component matrix resins. Pharmaceutical actives were cryogenically ground as a physical blend or an amorphous blend with the polymer. Subsequently, tablets were made by direct compression using a single tablet press, or capsules were made by filling them with the ground material. Dissolution tests were completed on the solid dosage forms at pH 1.2, 4.5, 6.8 or 7.4 in a United States Pharmacopeia (USP) II device to determine the release profiles for up to 24 h. Carboxymethylcellulose esters provide an excellent matrix for controlling both the rate of release and the pH at which pharmaceutical actives release into the aqueous environment. When used in suitable quantities, dictated by the active of interest, carboxymethylcellulose acetate butyrate provided zero-order release over sustained time up to 24 h.     

Development, characterization and performance evaluation of oro-dispersible tablet containing aceclofenac hydroxypropyl-β-cyclodextrin binary system

The purpose of this research was to mask the intensely bitter taste of aceclofenac (ACF) and to formulate oro dispersible tablet (ODT) of the taste-masked drug. Taste masking was done by complexing aceclofenac with Hydroxypropyl-β-Cyclodextrin (HPβCD) by different methods. Phase solubility studies indicated complex with possible stoichiometry of 1:1 and a stability constant of 221.11 M^?1. The complexes were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, and differential scanning calorimetry studies. The characterization studies confirmed inclusion of the ACF within the nonpolar cavity of HPβCD in the neutralization method (NM). Remarkable improvement in the in vitro drug release profiles in pH 6.8 phosphate buffer was observed with all complexes, especially the neutralization. The complexes of ACF–HPβCD (1:1) was compressed into tablet and properties of tablets such as tensile strength, wetting time, in vitro disintegration time, and disintegration in the oral cavity were investigated to elucidate the wetting and disintegration characteristics of tablets. Polyplasdone XL-10 7% wt/wt gave the minimum disintegration time. Tablets of batch F4 containing Avicel 200 and 7% wt/wt Polyplasdone XL-10 showed faster disintegration, within 12 s, than the marketed tablet (128 s). Good correlation between in vitro disintegration with in-house developed method and in the oral cavity was recognized. Taste evaluation of ODT in human volunteers revealed considerable taste masking with the degree of bitterness below threshold value. Thus, results conclusively demonstrated successful masking of taste and rapid disintegration of the formulated tablets in the oral cavity.     

Eudragit as controlled release system for anti-inflammatory drugs: A comparison between DSC and dialysis experiments

A comparative study between the release of Ibuprofen (IBU) from Eudragit RS100^® (RS) and RL100^® (RL) nanosuspensions as well as the free drug to a biological model membrane, consisting of dimyristoylphosphatidylcholine (DMPC) multilamellar vesicles (MLV), was carried out by DSC technique. The aim was to assess the suitability of such calorimetric technique to determine the kinetics of drug release from a polymer system, compared with a classical release test by dialysis method. Nanosuspensions were prepared by a modification of the quasi-emulsion solvent diffusion technique (QESD), a particular approach to the general solvent-change method. This kind of system was planned for the ophthalmic release of non-steroidal anti-inflammatory drugs in ocular diseases associated with inflammatory processes (i.e. post-cataract surgery or uveitis). The drug release was monitored by differential scanning calorimetry (DSC), following the effects exerted by IBU on the thermotropic behaviour of DMPC multilamellar vesicles. IBU affects the main transition temperature (T_m) of phospholipid vesicles, causing a shift towards lower values, driven by the drug fraction entering the lipid bilayer. The obtained values have been used as a calibration curve. DSC was performed on suspensions of blank liposomes added to fixed amounts of unloaded and IBU-loaded Eudragit RS100^® and RL100^® nanosuspensions as well as to powdered free drug. The T_m shifts caused by the drug released from the polymer system or by the free drug, during incubation cycles at 37 °C, were compared to the calibration curve in order to obtain the fraction of drug released. The results were also compared with in vitro dialysis release experiments. The suitability of the two different techniques to follow the drug release as well as the differences between the RL and RS polymer systems was compared, confirming the efficacy of DSC for studying the release from polymer nanoparticulate systems. Explanation of the different rate of kinetic release could be due to void liposomes, which represent a better up-taking system than the aqueous solution phase in the dialysis experiments.     

Preparation of Losartan Potassium Controlled Release Matrices and In-Vitro Investigation Using Rate Controlling Agents

Controlled release matrices have predictable drug release kinetics, provide drugs for an extended period of time, and reduce dosing frequency with improved patient compliance as compared with conventional tablet dosage forms. In the current research work, losartan potassium controlled release matrix tablets were fabricated and prepared with rate altering agents; that is, Ethocel grade 100 combined with Carbopol 934PNF. Various drug to polymer ratios were used. HPMC, CMC, and starch were incorporated in some of the matrices by replacing some amount of filler (5%). The direct compression method was adopted for the preparation of matrices. In phosphate buffer (pH 6.8), the dissolution study was conducted by adopting the USP method-I as the specified method. Drug release kinetics was determined and dissolution profiles were also compared with the reference standard. Prolonged release was observed for all matrices, but those with Ethocel 100FP Premium showed more extended release. The co-excipient (HPMC, CMC, and starch) exhibited enhancement in the drug release rates, while all controlled release matrices released the drug by anamolous non-Fickian diffusion mechanism. This combination of polymers (Ethocel grade 100 with Carbopol 934PNF) efficiently extended the drug release rates up to 24 h. It is suggested that these matrix tablets can be given in once a day dosage, which might improve patient compliance, and the polymeric blend of Ethocel grade 100 with Carbopol 934PNF might be used in the development of prolonged release matrices of other water-soluble drugs.     

Molecularly imprinted hydrogels for sustained release of sunitinib in breast cancer therapy

The present work reports on the synthesis of a molecularly imprinted polymer (MIP) based on methacrylic acid and ethylene glycol dimethacrylate for sunitinib delivery. Sunitinib (SUT) is a tyrosine kinase inhibitor used in many cancer diseases. Like the majority of the anticancer drugs, SUT suffers of a low bioavailability, and at the same time, it is characterized by a narrow therapeutic window. In order to reduce drug systemic toxicity, we synthesized a MIP‐based drug delivery system for SUT‐controlled release. MIP was obtained by bulk polymerization through the so‐called noncovalent approach. Rebinding experiments were performed to evaluate the success of the imprinting process and the ability of MIP to bind in a specific and selective fashion the template molecule. Resulting data showed that sunitinib rebinding percentage was 70%, while nonimprinted polymer (NIP) rebinding percentage was 46%. A not significant difference was observed between MIP and NIP in semaxanib binding experiments. Moreover, the drug release profiles were studied for both MIP and NIP. A sustained release was observed from sunitinib‐loaded MIP during 24 hours, reaching 58% after 6 hours and 76% at the end‐point. NIP, on the contrary, released almost 90% of the loaded drug within 6 hours. Furthermore, the drug carrier was tested in vitro against MCF‐7 cells, in which the cytotoxic effect of sunitinib released from MIP reached the maximum after 72 hours, while NIP completed its effect within 48 hours. These results demonstrated that molecularly imprinted polymers are suitable systems for SUT release.     

Controlled release of 5-fluorouracil or mitomycin-c from polymer matrix: Preparation by radiation polymerization and in vivo evaluation of the anticancer drug/polymer composites

Polymer tablets containing anticancer drugs such as 5-fluorouracil (5-FU) and mitomycin-C (MMC) have been prepared to evaluate the drug-release characteristics in vitro and the effect on local control of mouse solid tumors in vivo. Radiation-induced polymerization of hydrophilic monomers (2-hydroxyethyl methacrylate and related monomers) at low temperature (-80°C) was performed to immobilize 5-FU or MMC in the polymer matrix. The drug was dispersed as microcrystallines within the polymer matrix. The rate of drug release in vitro in buffer solution (pH7.0, 37°C) increased with increase in hydrophilicity of polymer matrix. Appropriate amount of crosslinks within the polymer matrix, as formed by ethylene glycol dimethacrylate (2G) added in the polymerization system, was effective to control the rate of drug release. The drug release became faster upon the addition of increasing amount of water in the radiation-induced polymerization. The tablet consisting of drug/polymer was buried surgically near solid tumors of striate muscle sarcoma (S180) transplanted to Kunming mice and the therapeutic effect of slow releasing drugs was evaluated in vivo by reference to intraperitoneal (i.p.) injection of the corresponding drugs. The slow releasing drugs led to high chemotherapeutic gain for local control of solid tumors with remarkable reduction of toxic side effect of the drugs.