L—天冬氨酸微生物电极的研制

本文以大肠杆菌为天冬氨酸脱氨反应的酶源，采用氨气酶电极为基础电极研制成Ｌ－天冬氨酸微生物电极。对细菌培养条件，固定方法及电极工作条件等进行了研究，测定Ｌ－天冬的氨酸Ｅ－１ｇＣ曲线斜率为５５ｍＶ，线性范围为６．０％×１０＾－４～８．０×１０＾－３ｍｏｌ／Ｌ，寿命可达１０天。     

铕与醛糖及铕与D─核糖、L─氨基酸络合作用的伏安法研究

Ｅｕ（３＋）在ＨＡｃ－ＮａＡｃ（ｐＨ４．６）溶液中与五碳醛糖有弱的络合作用，用循环伏安法和微分脉冲极谱可以观察到Ｄ－核糖，Ｄ－阿拉伯糖，Ｄ－木糖对Ｅｕ（３＋）还原波形的络合影响，使还原和氧化过程变得较为可逆，其中Ｄ－核糖最为明显，而来苏糖无影响．Ｅｕ（３＋）与氨基酸在相同实验条件下有络合作用，且在汞电极上有吸附现象，因此分别加入Ｌ－苯丙氨酸、Ｌ－组氨酸和Ｌ－蛋氨酸等，进一步改善了Ｅｕ（３＋）的波形而接近于可逆氧化－还原过程，其中以Ｅｕ（３＋）－Ｄ－核糖－Ｌ－苯丙氨酸最明确。绘出了在电极表面形成三元络合物的示意图。     

α—胰凝乳蛋白酶的固定化及其对DL—苯丙氨酸的光学拆分

以氨丙基多孔球为载体，戊二醛为交联剂制得固定化α－胰凝乳蛋白酶。其含酶量为３．６ｍｇ／ｇ，米氏常数Ｋｍ＝１．２×１０＾－３ｍｏｌ／Ｌ，最适宜温度为３５℃，ｐＨ值为７．０，对热、酸碱、甲醇以及尿素的稳定性有较大提高，Ｃａ＾２＋激活效应明显。用该固定化酶连续拆分ＤＬ－苯丙氨酸制备Ｌ－苯丙氨酸时，拆分产率高于９０％，产品纯度超过９６％；连续使用２个月后仍能保持较高酶活力。     

铂单晶电极表面不可逆反应动力学──Ⅱ铂单晶(100)晶面电极上甲酸氧化反应动力学参数解析

运用程序电位阶跃方法，避免甲酸解离吸附的干扰，成功地研究了Pt（100）单晶电极上甲酸经活性中间体直接氧化至CO2的反应动力学．提出对电化学暂态实验数据进行积分变换求解动力学参数的方法，编制了相关的计算机软件，首次获得甲酸在Pt（100）单晶电极上直接氧化的反应动力学参数。结果给出在0．02V至0．15V电位区间，速率常数kf的对数随电极电位线性增长，kf从9．51×10－4上升到1．38×10－2cm·s－1．获得传递系数β＝0．309，5×10－3mol·L－1HCOOH＋0．5mol·L－1H2SO4溶液中甲酸的扩散系数D＝1．80×10－5cm2．s－1．     

毛细管区带电泳电化学检测法测定药物及果汁中芦丁和L— …

用毛细管区带电泳－电化学检支同时测定复方芦丁片及果汁中芦丁和Ｌ－抗坏血酸的含量。研究了电极电位、电解液浓度和酸度、电泳电压及进样时间等对电泳的影响,得到了较为优化的测定条件。以直径为３００ｕｍ的碳圆盘电极为检测电极,电极电位为１．０Ｖ（υｓ．ＳＣＥ）,在２５０ｍｍｏｌ／Ｌ硼砂－５０ｍｍｏｌ／Ｌ ＮａＨ２ＰＯ４（ｐＨ ８．０）运行缓冲液中,上述两组分在１２ｍｉｎ内完全分离。芦丁和Ｌ－抗坏血酸浓度分别     

微分简易示波伏安法测定分子筛中微量钴的研究

微分简易示波伏安法是一种新的示波分析方法．与经典示波计时电位法相比，具有灵敏度高、去极剂峰高易于测定等优点．本文研究了CO－4（2一毗院偶氮）间苯二酚钠（PAR）体系的示波特性并探讨了应用微分简易示波伏安法测定微量钻的可能性．试验发现，在O．2mol／LHAc－0·2mol／LNaAc－2·5X10－’mol／LPAR底液中，钻离子在iFE曲线的阴极支上电位为一1．68V处产生一尖锐峰，其峰高与钻离子浓度在1．5X10’～1·2X10－‘mol／L范围内呈线性关系，检测灵敏度为5．OXIO－’mol／L‘以此拟定了测定微量钻的新方法．与光度法相比，该…     

由肉桂酸生物合成L-苯丙氨酸

本文评述了Ｌ－苯丙氮酸的各种合成路线、国内外的研究现状及工业化情况，重点讨论了由肉桂酸和氨生物合成Ｌ－苯丙氨酸的路线，提出了在国内进一步工作的建议。     

钼(Ⅵ)-向红菲啰啉络合物的吸附伏安行为

在 PH=4．0的 0．3 mol/L的 HAc－NaAc介质中，钼（Ⅵ）-向红菲啰啉体系在悬汞电极上，于-0．58 V（vs．SCE）电位处得到钼（Ⅵ）-向红菲啰啉络合物的吸附还原波，其1.5次微分伏安图的峰峰值epp与Mo（Ⅵ）在3．0X10-10”～1．2X10-7mol／L浓度范围内呈良好的线性关系，检测限可达8×10-11mol／LMo（Ⅵ）．方法用于豆类样品中微量钼的测定，结果较好。     

一种新的硫酸根离子敏感电极

探索新的材料制备离子敏感电极,研究这些电极的响应特性和响应机理,是离子电极研究的一个新方向［'－"．硫酸根离子敏感电极一直是离子电极研究中的一个难点·本文采用电沉积方法,在铜、钻、玻璃碳和低碳钢体表面沉积了Ni－P系非晶合金硫酸根离子敏感电极,电极对硫酸根离子在卫X10－'～IX10－'mol／L浓度范围内呈Nernst响应,检测下限可达4X10'mol／L,具有良好的重现性和稳定性．该硫酸根离子电极对常见阴离子具有良好的选择性,与迄今所报道的SO广离子敏感电极比较显示了较优异的特性．1实验部分将金属铜（99％,4-5mm）、金属钻…     

Nafion-聚[N′,N″-(1,3-丙二亚甲基)双(1,2-苯二氨基)-N,N′,N″,N]合镍修饰微电极用于测定一氧化氮的研究

详细报道了Ｎａｆｉｏｎ－聚［Ｎ′，Ｎ″－（１，３－丙二亚甲基）双（１，２－苯二氨基）－Ｎ，Ｎ′，Ｎ″，Ｎ］合镍［ＰｏｌｙＮｉ（Ⅱ）Ｌ］修饰微铂电极的制备及性质．实验表明，该修饰电极对ＮＯ有较高的灵敏度和选择性．当ＮＯ的浓度在２．０×１０－７～１．６×１０－５ｍｏｌ／Ｌ范围内峰电流与ＮＯ的浓度呈线性关系，相关系数ｒ＝０．９９４．用于血液中ＮＯ的检测，效果良好．     

Multilayer assembly of Prussian blue nanoclusters and enzyme-immobilized poly(toluidine blue) films and its application in glucose biosensor construction

A multilayered glucose biosensor via sequential deposition of Prussian blue (PB) nanoclusters and enzyme-immobilized poly(toluidine blue) films was constructed on a bare Au electrode using electrochemical methods. The whole configuration of the present biosensor can be considered as an integration of several independent hydrogen peroxide sensing elements. In each sensing element, the poly(toluidine blue) film functioned as both the supporting matrix for the glucose oxidase immobilization and the inhibitor for the diffusion of interferences, such as ascorbic acid and uric acid. Meanwhile, the deposited Prussian blue nanocluster layers acts as a catalyst for the electrochemical reduction of hydrogen peroxide formed from enzymatic reaction. Performance of the whole multilayer configuration can be tailored by artificially arranging the sensing elements assembled on the electrode. Under optimal conditions, the biosensors exhibit a linear relationship in the range of 1 x 10(-4) to 1 x 10(-2) mol/L with the detection limit down to 10(-5) mol/L. A rapid response for glucose could be achieved in less than 3 s. For 1 mM glucose, 0.5 mM acetaminophen, 0.2 mM uric acid, and 0.1 mM ascorbic acid have no obvious interferences (<5%) for glucose detection at an optimized detection potential. The present multilayered glucose biosensor with a high selectivity and sensitivity is promising for practical applications.     

Diffusion coefficient measurements in microfluidic devices

A glassy carbon electrode (GCE) modified with Pd/IrO(2) provides excellent electrocatalytic oxidation of hydrogen peroxide. Glucose oxidase (GOD) and xanthine oxidase (XOD) were co-immobilized on the modified electrode with a thin film Nafion coated on the enzyme layer to form a glucose (Glu)/hypoxanthine (Hx) sensor, without interference from electroactive species such as ascorbic acid (AA) and uric acid (UA). Its response was evaluated with respect to the enzyme amount on the electrode, pH and temperature of the electrolyte. The prepared bienzymic biosensor, used as the detector of HPLC gave a detection limit of 1.0x10(-6) mol l(-1) Glu and 2.0x10(-7) mol l(-1) Hx (Hx) with a linear concentration range of 5.0x10(-6)-2.5x10(-3) mol l(-1) and 1.0x10(-6)-5.0x10(-4) mol l(-1), respectively. Coupled with microdialysis, it was used to monitor the concentrations of Glu and Hx in rat brain.     

溶胶-凝胶法固定胆固醇氧化酶偶联普鲁士蓝化学修饰电极的研究

用溶胶-凝胶法将胆固醇氧化酶固定在普鲁士蓝修饰的玻碳电极表面,制成了一种新型胆固醇传感器,实现了低电位下对胆固醇的间接测定,胆固醇的测定范围伏安法为5×10^-7～8×10^-5mol/L,安培法为5×10^-6～5×10^-4mol/L.伏安法检出限为1.2×10^-7mol/L,是目前所见灵敏度最高的胆固醇传感器之一,该传感器对胆固醇的测定可避免常规电化学传感器测定中由于样品中大量存在的易氧化物质所带来的干扰,该传感器的寿命长,使用次数在300次以上.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized on L-glutathione self-assembled monolayers

A novel hydrogen peroxide biosensor has been fabricated based on covalently linked horseradish peroxidase （HRP） onto L- glutathione self-assembled monolayers （SAMs）. The SAMs-based electrode was characterized by electrochemical methods, and direct electrochemistry of HRP can be achieved with formal potential of-0.242 V （vs. saturated Ag/AgCl） in pH 7 phosphate buffer solution （PBS）, the redox peak current is linear to scan rate and rate constant can be calculated to be 0.042 s^-1. The HRP-SAMs- based biosensors show its better electrocatalysis to hydrogen peroxide in the concentration range of 1 × 10^-6 mol/L to 1.2 × 10^-3 mol/L with a detection limit of 4 × 10^-7 mol/L. The apparent Michealis-Menten constant is 3.12 mmol/L. The biosensor can effectively eliminate the interferences of dopamine, ascorbic acid, uric acid, catechol and p-acetaminophen.     

An Unmediated Hydrogen Peroxide Sensor Based on a Hemoglobin-sds Film Modified Electrode

ABSTRACT

An unmediated hydrogen peroxide sensor is designed in this paper by employing a hemoglobin-SDS film modified electrode. Hemoglobin exhibits direct (unmediated) electrochemistry at the modified electrode. The protein also shows elegant catalytic activity towards the electrochemical reduction of hydrogen peroxide. Consequently, a prototype hydrogen peroxide sensor is prepared. Under optimum conditions, this sensor provides a linear response over the hydrogen peroxide concentrations in the range of 1×10^-5～1×10^-4 mol/L. The detection limit was 2×10^-6 mol/L The relative standard deviation was 4.2% for 6 successive determinations of the hydrogen peroxide at 1×10^-5 mol/L. This configuration is shown to be sensitive, stable and easily fabricated. It might be useful in the biological and industrial fields.     

A stable glucose biosensor prepared by co-immobilizing glucose oxidase into poly(p-chlorophenol) at a platinum electrode

An amperometric glucose biosensor was successfully developed by electrochemical polymerization of p-chlorophenol (4-CP) at a Pt electrode in the presence of glucose oxidase. The amperometric response of this biosensor to hydrogen peroxide, formed as the product of enzymatic reaction, was measured at a potential of 0.6 V (vs. SCE) in phosphate buffer solution. The performances of sensors, prepared at different monomer concentrations and polymerization potentials, were investigated in detail. The biosensor prepared under optimal conditions had a linear response to glucose ranging from 2.5 x 10(-4) to 1.5 x 10(-2) mol L(-1) with a correlation coefficient of 0.997 and a response time of less than 2 s. Substrate selectivity of the polymer-based enzyme electrode was tested for coexisting interferents such as uric acid and ascorbic acid, and no discernible response was observed. After 90 days, the response of the biosensor remained almost unchanged, indicating very good stability.     

Amperometric enzyme electrodes for the determination of l-glutamate

Electrodes for amperometric measurement of l-glutamate were prepared by immobilization of l-glutamate oxidase on an Immobilon-AV Affinity membrane and attachment to an oxygen/hydrogen peroxide sensor. The response of the hydrogen peroxide sensor was linear over the concentration range 5.0 x 10(-8)-5.0 x 10(-4)Ml-glutamate, with a limit of detection of 35nM. Attachment of a size-exclusion membrane (cut-off for molecular weight > 100) or of a hydrophobic oxygen membrane eliminated electro-oxidizable interferences, but the response was attenuated by a factor of 2-3. The response may be amplified 10-fold by co-immobilizing l-glutamate dehydrogenase with the l-glutamate oxidase. The electrode initially lost 25% of its activity but was then stable for more than 320 days and at least 200 assays. The electrode was successfully used to assay glutamate in a protein tablet and in several food products. A flow-injection system was assembled for the continuous assay of l-glutamate.     

An electrochemiluminescent sensor for glucose employing a modified carbon nanotube paste electrode

A carbon nanotube paste (CNTP) electrode and a carbon nanotube paste/glucose oxidase (CNTP/GOx) electrode were prepared, and the electrochemiluminescent (ECL) behavior of luminol in the presence of glucose was investigated in detail at each of these electrodes. Compared to the classical carbon paste (CP) electrode, the CNTP electrode incorporating glucose oxidase greatly enhanced the response of the ECL sensor to glucose due to the electrocatalytic activity of the carbon nanotubes, the specificity of the enzymatic reaction, and the sensitivity of the luminol ECL reaction. Under optimal conditions, the electrode was found to respond linearly to glucose in the concentration range 1.0x10(-6) approximately 2.0x10(-3) mol/L, and the detection limit (defined as the concentration that can be detected at a signal-to-noise ratio of 3) was found to be a glucose concentration of 5.0x10(-7) mol/L. The method used to prepare the CNTP/GOx electrode was very convenient, and the electrode surface could be renewed in the case of fouling by simply polishing or cutting it to expose a new and fully active surface. The relative standard deviations (RSD) were found to be 6.8% and 8.9% for the CNTP electrode and the CNTP/GOx electrode (n=6). The electrode retained 95% of its initial response after two weeks.     

A Cholesterol Biosensor Based on Entrapment of Cholesterol Oxidase in a Silicic Sol‐Gel Matrix at a Prussian Blue Modified Electrode

A cholesterol biosensors fabricated by immobilization of cholesterol oxidase (ChOx) in a layer of silicic sol‐gel matrix on the top of a Prussian Blue‐modified glassy carbon electrode was prepared. It is based on the detection of hydrogen peroxide produced by ChOx at ?0.05 V. The half‐lifetime of the biosensor is about 35 days. Cholesterol can be determined in the concentration range of 1×10^?6?8×10^?5 mol/L with a detection limit of 1.2×10^?7 mol/L. Normal interfering compounds, such as ascorbic acid and uric acid do not affect the determination. The high sensitivity and outstanding selectivity are attributed to the Prussian Blue film modified on the sensor.     

基于单壁碳纳米管-DNA酶复合结构的电化学生物传感器

结合DNA酶优异的氧化还原催化特性和碳纳米管的电化学特性, 制备了单壁碳纳米管-DNA酶复合材料, 并通过壳聚糖将其固定到玻碳电极表面构建了电化学生物传感界面. 研究了单壁碳纳米管-DNA酶复合结构的氧化还原反应催化特性, 并以此为传感平台构建了葡萄糖氧化酶电化学生物传感器. 结果表明, 单壁碳纳米管-DNA酶复合材料修饰的电极对过氧化氢的响应具有较宽的线性范围(5×10^-6~1×10^-2 mol/L)和良好的检测灵敏度(检出限为1×10^-6 mol/L). 采用制备的葡萄糖氧化酶传感器实现了对葡萄糖的快速灵敏检测.