Role of annealing environment and partial pressure on structure and optical performance of TiO2 thin films fabricated by rf sputter method

Influences of the different annealing ambient (in air, 1 bar, 2 bar, 3 bar and 4 bar oxygen partial pressure) on the titanium dioxide (TiO₂) thin films deposited on soda lime glass by standard radio frequency (rf) magnetron reactive sputtering method at 100 watt were investigated by means of X–ray diffractometer (XRD), ultra violet spectrometer (UV–vis), and Scanning Electron Microscopy (SEM). It was found that either optical properties or energy band gaps of the films enhanced with increase in the oxygen partial pressure up to 3 bar. The energy band gaps of the films (except for the film annealed in 4 bar oxygen partial pressure) became larger than the film annealed in atmospheric pressure. The best transmission was observed for the thin film annealed in 3 bar oxygen partial pressure. Moreover, not only was grain–like structure found to be more dominant than dot–like structure but also growth of anatase phase was observed instead of that of the rutile phase with increasing oxygen partial pressure up to 3 bar. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of calcination on the crystallinity of sputtered TiO2 thin films as studied by Raman scattering

Titanium dioxide films have been deposited using DC magnetron sputtering technique onto silicon substrates at an ambient temperature and at an oxygen partial pressure of 7 × 10 ^–5 mbar and sputtering pressure (Ar + O₂) of 1 × 10 ^–3 mbar. The deposited films were calcinated at 673 and 773 K. The composition of the films as analyzed using Auger Electron Spectroscopy (AES) revealed the stoichiometry with an O and Ti ratio of 2.08. The influence of post‐deposition calcination on the Raman scattering of the films was studied. The existence of Raman active modes A_1g, B_1g and E_g corresponding to the Raman shifts are reported in this paper. The improvement of crystallinity of the TiO₂ films as shown by the Raman scattering studies has also been reported. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Substrate temperature effect on the optical properties of amorphous Sb2S3 thin films

Sb₂S₃ amorphous thin films were prepared by thermal evaporation of corresponding powder on thoroughly cleaned glass substrates held at temperature in the range 300‐473 K. X‐ray diffraction and atomic force microscopy have been used to order to identify the structure and morphology of surface thin films. The optical constants of the deposition films were obtained from the analysis of the experimental recorded transmission data over the wavelength range 400‐1400 nm. An analysis of the absorption coefficient values revealed an optical indirect transition with the estimation of the corresponding band gap values. It was found that the optical band gap energy decrease with substrate temperature from 1.67 eV at 300 K to 1.48 eV at 473K. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of annealing on the structural,electrical and optical properties of nanostructured TiO2 thin films

Nanostructured titanium dioxide thin films were prepared using reactive pulsed laser ablation technique. Effects of annealing on the structural, morphological, electrical and optical properties are discussed. The structural, electrical and optical properties of TiO₂ films are found to be sensitive to annealing temperature and are described with GIXRD, SEM, AFM, UV‐Visible spectroscopy and electrical studies. X‐ray diffraction studies showed that the as‐deposited films were amorphous and at first changed to anatase and then to rutile phase with increase of annealing temperature. Optical constants of these films were derived from the transmission spectra and the refractive index dispersion of the films, subjected to annealing at different temperatures, is discussed in terms of the single oscillator‐Wemple and Didomenico model. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optical properties of Mg‐doped ZnO thin films prepared by a modified Pechini method

ZnO thin films with different Mg doping contents (0%, 3%, 5%, 8%, 10%, respectively) were prepared on quartz glass substrates by a modified Pechini method. XRD patterns reveal that all the thin films possess a polycrystalline hexagonal wurtzite structure. The peak position of (002) plane for Mg‐doped ZnO thin films shifts toward higher angle due to the Mg doping. The crystallite size calculated by Debey‐Scherrer formula is in the range of 32.95–48.92 nm. The SEM images show that Mg‐doped ZnO thin films are composed of dense nanoparticles, and the thickness of Mg‐doped ZnO thin films with Mg doped at 8% is around 140 nm. The transmittance spectra indicate that Mg doping can increase the optical bandgap of ZnO thin films. The band gap is tailored from 3.36 eV to 3.66 eV by changing Mg doping concentration between 3% and 10%. The photoluminescence spectra show that the ultraviolet emission peak of Mg‐doped ZnO thin films shifts toward lower wavelength as Mg doping content increases from 3% to 8%. The green emission peak of Mg‐doped ZnO thin films with Mg doping contents were 3%, 8%, and 10% is attributed to the oxygen vacancies or donor‐acceptor pair. These results prove that Mg‐doped ZnO thin films based on a modified Pechini method have the potential applications in the optoelectronic devices.     

Influence of thermoannealing on crystallinity and optical properties of Sb2S3 thin films

Sb₂S₃ thin films are obtained by evaporating of Sb₂S₃ powder onto glass substrates maintained at room temperature under pressure of 2×10^‐5 torr. The composition of the thin films was determined by energy dispersive analysis of X‐ray (EDAX). The effect of thermal annealing in vacuum on the structural properties was studied using X‐ray diffraction (XRD) technique and scanning electron microscopy (SEM). The as‐deposition films were amorphous, while the annealed films have an orthorhombic polycrystalline structure. The optical constants of as‐deposited and annealed Sb₂S₃ thin films were obtained from the analysis of the experimental recorded transmission spectral data over the wavelength range 400‐1400 nm. The transmittance analysis allowed the determination of refractive index as function of wavelength. It was found that the refractive dispersion data obeyed the single oscillator model, from which the dispersion parameters (oscillator energy, E₀, dispersion energy, E_d) were determined. The static refractive index n(0), static dielectric constant, ε_∞, and optical band gap energy, E_g, were also calculated using the values of dispersion parameters. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical constants of DC magnetron sputtered titanium dioxide thin films measured by spectroscopic ellipsometry

Optical constants of DC magnetron sputtered TiO₂ thin film have been determined by Spectroscopic Ellipsometry in the photon energy range 1.2 to 5.5 eV at room temperature. The measured dielectric‐function spectra reveal distinct structures at energies of the E1, E1 + Δ1 and E2 critical points are due to interband transitions. The root mean square roughness of the magnetron sputtered TiO₂ thin films evaluated by ex‐situ atomic force microscopy is 5.8 nm. The Dielectric constant values were found to be substantially lower than those for the bulk TiO₂. The dielectric related Optical constants, such as the refractive index, extinction coefficient, absorption coefficient and normal incidence of reflectivity determined from the spectroscopic ellipsometry data are presented and analyzed. The optical constants of the films were also determined using the optical transmittance measurements and the results were discussed. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth,structure and optical characterization of Al‐doped ZnO nanoparticle thin films

Al‐doped ZnO nanoparticle thin films were prepared on glass substrate at the optimum temperature of (410±10) °C by spray pyrolysis technique using zinc nitrate as a precursor solution and aluminium chloride as a dopant. The dopant concentration (Al/Zn at%) was varied from 0 to 2 at%. Structural analysis of the films shows that all the films are of polycrystalline zinc oxide in nature, possessing hexagonal wurtzite structure. The films exhibit variation in peak intensities corresponding to (100), (002) and (101) reflection planes on Al‐doping. The crystallite size calculated by Scherrer formula has been found to be in the range of 35‐65 nm. The optical absorption study shows that the optical band gap in the Al‐doped films varies in the range of 3.11 – 3.22 eV. The width of localized states in the band gap estimated by the Urbach tail analysis has been found to be minimum in case of the 1 at% Al‐doped zinc oxide thin film. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of substrate temperature on structural and materials properties of zirconium nitride films on D9 steel substrates

Thin zirconium nitride (ZrN) films were prepared by using reactive direct current (DC) magnetron sputtering onto D9 steel substrates. XRD technique was employed to study the coatings, observing variations of crystallite size, crystallite texture and lattice constant, as a function of substrate temperature. Chemical states of the ZrN thin films were determined by X‐ray photoelectron microscopy (XPS). AFM picture showed the presence of spherical shaped grains on the top of homogeneous granular surface. The hardness and elastic modulus values were measured by nanoindendation and their values are 18.5 and 343 GPa respectively. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Epitaxial Sn1‐xPbxS nanorods on iso‐compositional thin films

Based on SnS (Herzenbergite) – SnPbS₂ (Teallite) mixed crystals with orthorhombic layer structures, thin films and lawns of Sn_1‐xPb_xS nanorods were produced using hot wall vacuum deposition method (HWVD). The lawn was formed onto the surface of an underlying thin Sn_1‐xPb_xS film which is build by differently oriented blocks. The density of rods arranged like a lawn depends on the metal ratio and substrate temperature. X‐ray and TEM analysis of the epitaxial material showed preferential (001) orientation perpendicular to the surface of the glass substrate. The roughness of the films measured by atomic force microscopy was in the range of R_q = 49.5–86.3 nm depending on lead concentration The rods were about 500 nm high and 300 nm in diameter. As revealed by TEM‐EDX experiments the droplet at the tip of rods consists of tin. Therefore it is assumed the rods grew via a self‐consuming vapor–liquid–solid (VLS) mechanism. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural,optical and electrical properties of GeO2 thin films prepared by sol‐gel method

GeO₂ thin films were prepared by sol‐gel method on ITO/Glass substrate. The electrical and optical properties and the microstructures of these films were investigated with special emphasis on the effects of an annealing treatment in ambient air. The films were annealed at various temperatures from 500 °C to 700 °C. Structural analysis through X‐ray diffraction (XRD) and atomic force microscope (AFM) showed that surface structure and morphological characteristics were sensitive to the treatment conditions. The optical transmittance spectra of the GeO₂/ITO/Glass were measured using a UV‐visible spectrophotometer. All films exhibited GeO₂ (101) orientation perpendicular to the substrate surface where the grain size increased with increasing annealing temperature. The optical transmittance spectroscopy further revealed high transparency (over 70 %) in the wave range 400 – 800 nm of the visible region. At an annealing temperature level of 700 °C, the GeO₂ films were found to possess a leakage current density of 1.31×10^‐6A/cm² at an electrical field of 20 kV/cm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

UV,violet and blue‐green luminescence from RF sputter deposited ZnO:Al thin films

The mechanism of ultraviolet (UV), violet and blue green emission from ZnO:Al (AZO) thin films deposited at different radio frequency (r.f.) powers on glass substrates was investigated. The structure and surface morphology of AZO films have also been observed. The optical transmittance spectra shows more than 80% transmittance in the visible region and the band gap is found to be directly allowed. From the photoluminescence measurement, intense UV and blue green luminescence is obtained for the samples deposited at higher sputtering powers. The mechanism of luminescence suggests that UV luminescence of AZO thin film is related to the transition from near band edge to the valence band and the concentration of antisite oxide (O_zn) increases with increase in r.f. power which in turn increases the intensity of green band emission while the violet PL is due to the defect level transition in the grain boundaries of AZO films. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and optical properties of CuInS2 thin films prepared by sulfurization of electrodeposited Cu‐In layers

The chalcopyrite CuInS₂ thin film was fabricated at 500 °C for 2 h by sulfurization of Cu‐In layers (as precursors) that were sulfurized in a glass tube with pure sulfur powder. The structural, morphological, and optical properties of CuInS₂ thin films are characterized using X‐ray diffraction (XRD), field‐emission scanning electron microscope (FE‐SEM), and UV/Visible/NIR spectrophotometer. The study of UV/Visible/NIR absorption shows the band gap energy value of CuInS₂ thin films is 1.5 eV. The XRD pattern shows the film is pure CuInS₂; no other peaks, such as CuS or CuIn₅S₈ were observed. Furthermore, the surface of the CuInS₂ film is compact characterized by FE‐SEM, which also shows the disappearance of CuS on the surface at 500 °C.     

Sputter power and sputter pressure influenced structural and optical behaviour of RF sputtered nanocrystalline ZnO films

Zinc oxide thin films were deposited on p‐type (100) silicon and Corning glass substrate by using RF magnetron sputtering at different sputter powers range 100–200 W and sputter pressures range 2–8 Pa. The deposited films were characterized by X‐ray diffraction, atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscope and UV‐Vis‐NIR spectrophotometer. The films formed at sputter power of 100 W consists of weak (100) reflection and then sputter power increased to 150 W additional (110) reflection was present with enhancement in the intensity of (100) peak. Further increase of sputtering power to 200 W the intensity of (100) phase decreased with the presence of additional peaks of (002) and (101) of ZnO. The FTIR analysis confirms the Zn‐O absorption band was located at 414 cm^‐1. The optical band gap of zinc oxide films decreased from 3.28 to 3.07 eV with increase of sputter power from 100 to 200 W. The maximum crystallite size of 21 nm, the root mean square roughness of 7.2 nm was found at films formed at working pressure of 5 Pa. The optical transmittance of the films increased from 88 to 96% and then decreased to 84% with increase of sputter pressure from 2 to 8 Pa.     

Optical and electrical studies on spray deposited ZnO thin films

ZnO thin films were prepared by spray pyrolytic decomposition of zinc acetate onto a glass substrate. These films were analyzed for the optical and electrical properties. Optical studies show that in these films the electronic transition is of the direct transition type. The optical energy gap for the films of different thicknesses is estimated to be in the range 2.98 – 3.09 eV. Electrical studies indicate that the films exhibit thermally activated electronic conduction and the activation energies are found to be dependent on the film thickness. The complex impedance measurements were carried out over a wide range of frequencies at room temperature (300 K). All the impedance spectra contain only a single arc, but the arc has a non‐zero intersection with the real axis in the high frequency region. Also, the arc has its centre lying below with the real axis which indicates the multirelaxation behavior of the films. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural,optical, and electrical properties of electron beam evaporated CdSe thin films

CdSe films have been deposited on glass substrates at different substrate temperatures between room temperature and 300 °C. The films exhibited hexagonal structure with preferential orientation in the (002) direction. The crystallinity improved and the grain size increased with temperature. Band gap values are found decreasing from about 1.92 eV to 1.77 eV with increase of the substrate temperature. It is observed that the resistivity decreases continuously with temperature. Laser Raman studies show the presence of 2 LO and 3 LO peaks at 416 cm^‐1 and 625 cm^‐1respectively. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Studies on optical properties of polycrystalline SnO2:Sb thin films prepared using SnCl2 precursor

Optical properties of spray deposited antimony (Sb) doped tin oxide (SnO₂) thin films, prepared from SnCl₂ precursor, have been studied as a function of antimony doping concentration. The doping concentration was varied from 0‐4 wt.% of Sb. All the films were deposited on microscope glass slides at the optimized substrate temperature of 400 °C. The films are polycrystalline in nature with tetragonal crystal structure. The doped films are degenerate and n‐type conducting. The sheet resistance of tin oxide films was found to decrease from 38.22 Ω/□ for undoped films to 2.17 Ω/□ for antimony doped films. The lowest sheet resistance was achieved for 2 wt.% of Sb doping. To the best of our knowledge, this sheet resistance value is the lowest reported so far, for Sb doped films prepared from SnCl₂ precursor. The transmittance and reflectance spectra for the as‐deposited films were recorded in the wavelength range of 300 to 2500 nm. The transmittance of the films was observed to increase from 42 % to 55 % (at 800 nm) on initial addition of Sb and then it is decreased for higher level of antimony doping. This paper investigates the variation of optical and electrical properties of the as‐deposited films with Sb doping. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical and opto‐electronic properties of polycrystalline Cd0.96Zn0.04Te thin films

Cd_0.96Zn_0.04Te thin films are deposited onto thoroughly cleaned glass substrates (Corning 7059) kept at room temperature by vacuum evaporation. The films are found to have good stoichiometry as analyzed by Rutherford Backscattering Spectrometry. The films exhibited zinc blende structure with predominant (111) orientation. The surface morphology of the films is studied by Atomic Force Microscopy. The rms roughness of the films evaluated by AFM is 3.7 nm. The pseudodielectric‐function spectra, ε(E) = ε₁(E) + i ε₂(E) at room temperature are measured by spectroscopic ellipsometry. The measured dielectric function spectra reveal distinct structures at energies of the E₁, E₁+ Δ₁ and E₂ critical points. The band gap energy of the films measured by optical transmittance measurement is 1.523 eV. The PL spectrum of the films shows intense emission due to free and bound exciton recombination and no emission associated with crystal imperfection and deeper impurity levels. The PL line shapes give indications of the high quality of the layers.     

Properties of Sm‐doped CaNb2O6 thin films deposited by radio‐frequency magnetron sputtering

Sm‐doped CaNb₂O₆ (CaNb₂O₆:Sm) phosphor thin films were prepared by radio‐frequency magnetron sputtering on sapphire substrates. The thin films were grown at several growth temperatures and subsequently annealed at 800 °C in air. The crystallinity, surface morphology, optical transmittance, and photoluminescence of the thin films were investigated by X‐ray diffraction, scanning electron microscopy, ultraviolet‐visible spectrophotometry, and fluorescence spectrophotometry, respectively. All of the thin films showed a main red emission radiated by the transition from the ⁴G_5/2 excited state to the ⁶H_9/2 ground state of the Sm³⁺ ions and several weak bands under ultraviolet excitation with a 279 nm wavelength. The optimum growth temperature for depositing the high‐quality CaNb₂O₆:Sm thin films, which was determined from the luminescence intensity, was found to be 400 °C, where the thin film exhibited an orthorhombic structure with a thickness of 370 nm, an average grain size of 220 nm, a band gap energy of 3.99 eV, and an average optical transmittance of 85.9%. These results indicate that the growth temperature plays an important role in controlling the emission intensity and optical band gap energy of CaNb₂O₆:Sm thin films.     

Influence of thermal annealing on the composition and structural parameters of DC magnetron sputtered titanium dioxide thin films

Titanium dioxide films have been deposited using DC magnetron sputtering technique. Films were deposited onto RCA cleaned p‐silicon substrates at the ambient temperature at an oxygen partial pressure of 7 × 10^–5 mbar and sputtering pressure of 1 × 10 ^–3 mbar. The deposited films were annealed in the temperature range 673–873 K. The structure and composition of the films were confirmed using X‐ray diffraction and Auger electron spectroscopy. The structure of the films deposited at the ambient was found to be amorphous and the films annealed at 673 K and above were crystalline with anatase structure. The lattice constants, grain size, microstrain and the dislocation density of the film are calculated and correlated with annealing temperature.