TiO2纳米管阵列光电催化氧化处理氨氮废水

用电化学阳极氧化法制备了高度有序的钛基二氧化钛纳米管阵列薄膜。用场发射扫描电镜(FE-SEM)、X射线衍射(XRD)表征样品的形貌与晶型特征。以二氧化钛纳米管阵列为光阳极,石墨为对电极,测试了不同pH值和外加偏压条件下的光电流响应和光电催化氧化降解NH4Cl水溶液(以N计,100 mg·L-1)的效率。结果表明:所制备的TiO2纳米管阵列具有锐钛矿和金红石的混晶结构,且主要晶型为锐钛矿。光电流响应的强弱与光电催化氧化效率的高低相对应,降解氨氮废水的最佳条件为pH=11,偏压为1.0 V。     

钛基TiO2纳米管阵列电极的光电催化性能

应用电化学阳极氧化法在纯Ti基底上制备高度有序的TiO2纳米管阵列,考察了Ti/TiO2光阳极的光电化学响应.以苯酚溶液为目标污染物,研究Ti/TiO2电极的光电催化性能,并与光催化性能进行比较.结果表明,该电极光电催化性能优于光催化性能.施加0.6 V电压时,光电催化性能最好.电化学阻抗谱分析显示,光电催化和光催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

掺杂纳米金粒子的火焰氧化TiO2膜的光电化学性质的研究

A nano-Au modified TiO2 electrode was prepared via the oxidation of Ti sheet in flame and subsequent modification with gold nanoparticles. The results of SEM and TEM measurements show that the Au nanoparticles are well dispersed on TiO2 surface. A near 2-fold enhancement in photocurrent was achieved upon the modification with Au nanoparticles. From the results of photocurrent and electrochemical impedance experiments it was found that the flatband potential of nano-Au/TiO2 electrode negatively shifted about 100 mV in 0.5 mol/L Na2SO4 solutions compared with that of bare TiO2 electrode. The improvement of photoelectrochemical performance was explained by the inhibition for charge recombination of photo-induced electrons and holes, and the promotion for interracial charge-transfer kinetics at nano-Au/TiO2 composite film. Such nanometal-semiconductor composite films have the potential application in improving the performance of photoelectrochemical solar cells.     

Photoelectrochemical oxidation of hydrazine on TiO2 modified titanium electrode: its application for detection of hydrazine

Despite extensive investigations on the photoelectrochemical properties of TiO₂-based electrodes, it is surprising that no photoelectrochemical investigation has been done for the case of hydrazine oxidation. In this paper, TiO₂ modified titanium (Ti/TiO₂) electrode was fabricated by anodization process under a constant applied potential. The morphological and microstructural characterization of the Ti/TiO₂ electrode was performed by scanning electron microscopy (SEM). The electrochemical and photoelectrochemical behavior of Ti/TiO₂ electrode in the absence and presence of hydrazine was examined by cyclic voltammetry and linear sweep voltammetry. Experimental results indicated that the photocurrent response of photoelectrode was highly increased in the presence of hydrazine especially at lower potentials. It can be due to hole scavenging effect of hydrazine which decreases the recombination of photogenerated electrons and holes. Based on these perceptions, a simple photoelectrochemical sensor for detection of hydrazine was obtained. The sensor showed high reproducibility, stability, and selectivity properties. This photoelectrode was successfully applied for direct determination of hydrazine in tap water.     

The photoactivity of porous Tio2 anodized at a high voltage

The photoactivity of TiO₂ produced by high-voltage anodization as described by Marchenoir et al. was compared to single-crystal TiO₂. The anodic oxide film was found to be highly porous. The photocurrent and quantum yield of the anodic sample is markedly larger on the long-wavelength side of the action spectrum as compared to sinle-crystal rutile. We ascribe this behavior either to the formation of anatase “pockets” in the film or to the incomplete oxidation of Ti during the anodization process.     

Photoelectrocatalytic degradation of 3-nitrophenol at surface of Ti/TiO2 electrode

The widely utilization of phenol and its derivatives such as 3-nitrophenol (3-NP) has led to the worldwide pollution in the environment. In this study, Ti/TiO₂ photoelectrode was prepared with anodic oxidation of Ti foil electrode and then the photoelectrocatalytic (PEC) degradation of 3-NP was performed via this electrode, comparing with photocatalytic (PC), electrooxidation and direct photolysis by ultraviolet light. A significant photoelectrochemical synergetic effect in 3-NP degradation was observed on the Ti/TiO₂ electrode and rate constant for the PEC process of Ti/TiO₂ electrode was about three times as high as its PC degradation process. 3-NP concentration monitoring was carried out with differential pulse voltammetry. Results showed that PEC degradation has highest effect on concentration decreasing of 3-NP at solution and degraded it about 38 %, while other processes degradation efficiencies were about 4, 7, and 12 % for electrooxidation, direct photolysis and photocatalytic degradation, respectively. Finally, effects of solution pH and applied potential on degradation efficiency were studied and results showed that optimum pH for degradation is equal 4.00 and optimum potential is 1.2 V vs. Ag|AgCl|KCl (3M) reference electrode.     

Fabrication of TiO2/Ti nanotube electrode and the photoelectrochemical behaviors in NaCl solutions

Titanium oxide nanotube electrodes were successfully prepared by anodic oxidation on pure Ti sheets in 0.5 wt.% NH₄F + 1 wt.% (NH₄)₂SO₄ + 90 wt.% glycerol mixed solutions. Nanotubes with diameter 40–60 nm and length 7.4 μm were observed by field emission scanning electron microscope. The electrochemical and photoelectrochemical characteristics of TiO₂ nanotube electrode were investigated using linear polarization and electrochemical impedance spectroscopy techniques. The open-circuit potential dropped markedly under irradiation and with the increase of Cl⁻ concentrations. A saturated photocurrent of approximately 1.3 mA cm⁻² was observed under 10-W low-mercury lamp irradiation in 0.1 M NaCl solution, which was much higher than film electrode. Meanwhile, the highest photocurrent in NaCl solution implied that the photogenerated holes preferred to combine with Cl⁻. Thus, a significant synergetic effect on active chlorine production was observed in photoelectrocatalytic processes. Furthermore, the generation efficiency for active chlorine was about two times that using TiO₂/Ti film electrode by sol–gel method. Finally, the effects of initial pH and Cl⁻ concentration were also discussed.     

Light energy accumulation using Ti/RuO2 electrode as capacitor

In the present study, the possibility to use Ti/RuO₂ electrode as capacitor for storage of photoelectrons generated under UV irradiation in Ti/TiO₂ photoelectrode has been investigated. A light-sensitive TiO₂ layer has been formed by means of anodizing Ti electrode in the solution of 0.5 M H₂SO₄. A layer of RuO₂, exhibiting the properties of electrochemical capacitor, has been formed by means of thermal decomposition of RuOHCl₃ also on Ti substrate. The photocharging capability of RuO₂ has been studied by means of short-circuiting Ti/RuO₂ electrode with Ti/TiO₂ photoelectrode in deaerated solution of 0.1 M KOH. It has been shown that the intensity of photocurrent flowing from Ti/TiO₂ to Ti/RuO₂ electrode depends mainly on the potential of the latter. Maximum value of photocurrent density was ∼180 μA cm⁻², which corresponded to maximum value of photon-to-electron conversion efficiency (IPCE) of about 60%. The amount of photogenerated charge Q _ph, which can be stored, depends on the capacitance of RuO₂ coating. Under the conditions of the experiment, Q _ph ranged from ∼35 to ∼50 mC, which corresponded to a specific charge of RuO₂ coating ranging between ∼20 and ∼30 mAh g⁻¹.     

Comparison of photocatalytic degradation kinetic characteristics of different organic compounds at anatase TiO2 nanoporous film electrodes

Photoelectrochemical method was adopted to investigate the photocatalytic oxidation of different organic compounds. It was found that at the anatase TiO₂ nanoporous electrode, the potential bias changes the rate-determining step from electron migration in the film at low potentials to photohole capture at relatively high potentials. When the applied potential bias is sufficient, the steady state photocurrent obtained reflects exclusively the rate of photohole capture at TiO₂ surface. Under such conditions, the photocatalytic degradation of various organic compounds with different chemical structures was studied.At very low concentrations, the linear increase of steady state photocurrent with the concentration was observed for all compounds investigated, due to the mass transfer limitation, although the number of electron needed for complete mineralization of these compounds differs markedly. It was demonstrated that the substrate molecules that reaches the electrode surface have been exhaustively mineralized under mass transfer-controlled conditions regardless of their chemical nature.At high concentration, substrate molecules (or intermediates) are accumulated on the surface (or in the reaction zone). As a result, the steady state photocurrent deviated from the linear relationship. Under such conditions, the interaction of substrate molecules and/or partially degraded intermediates with TiO₂ determines the overall photohole capture rate. The differences in photohole capture rate among different organic compounds were observed. The kinetic characteristics of different organic compounds at high concentrations were also explained based on the structural differences.     

低温吸附制备Au-TiO2复合薄膜及其光电化学性质

在低温条件下将预先合成的Au溶胶吸附到TiO₂薄膜上以制备纳米Au-TiO₂复合薄膜,以超高分辨率场发射扫描电镜(FESEM)、X射线衍射(XRD)及X射线光电子能谱(XPS)表征Au-TiO₂膜,并在UV辐照下测定了Au-TiO₂薄膜电极的光电化学性质。纳米Au呈金属态,平均粒径为(4.3±1.2) nm,负载量高,均匀地沉积于TiO₂薄膜表面。光电化学测试表明,沉积纳米Au后,TiO₂电极的光生电流提高近5倍,光生电压明显向负值增大,说明纳米Au可增强光生载流子的分离效率,促进电荷在电极与溶液界面间的转移。Au-TiO₂电极的电荷传递法拉第阻抗(R_ct)是TiO₂电极的一半,说明负载的纳米Au粒抑制了光生电子-空穴的复合,提高了电极中载流子浓度。     

偏压控制Cu2O和Cu在TiO2表面的生长及其光电化学性质

基于TiO₂/Ti 电极在含Cu²⁺溶液中的循环伏安图,调节电沉积的沉积电压,我们在TiO₂平整表面制备出Cu₂O和/或Cu颗粒. 通过扫描电镜（SEM）、X射线衍射（XRD）和X射线光电子能谱（XPS）表征,发现Cu₂O和Cu有不同的生长机制：Cu₂O颗粒在TiO₂表面分散结晶,而Cu颗粒是在已生长的颗粒上成核,从而形成堆积颗粒结构. 这是由于在Cu₂O/TiO₂界面和Cu/TiO₂界面形成不同的能带结构,使得电子的转移方式不同. 与纯TiO₂光阳极比较,可以观察到Cu₂O/TiO₂和Cu/TiO₂异质结构的光电流均有显著增强. 特别地,存在一个电压区间使得Cu₂O和Cu同时生长在TiO₂表面,此时对应的光电流比较稳定并且能达到最大. 紫外-可见（UV-Vis）漫反射光谱、电化学阻抗谱（EIS）和光电流-电压特性曲线均显示,Cu₂O和Cu明显有助于光的可见光吸收,同时Cu/TiO₂在光电转换过程中显示更宽波段的可见光利用率. 此外,开路电压的增加、有效的电荷分离和电极/电解质界面上载流子的快速迁移也增强了材料的光电化学性质.     

TiO2纳米薄膜电极中光生载流子传输特性研究

采用sol-gel法制备了均匀透明的锐钛矿相纳米TiO₂薄膜电极. 通过瞬态光电流谱研究了液相电解液中所制备电极内光生载流子的传输特性. 结果表明: 在TiO₂/电解液界面处, TiO₂颗粒表面存在两种能够捕获光生电子的表面态. 一种是O₂吸附所形成的浅能级表面态(S_o), 能级位于导带下0.5 eV以内, 其捕获光生电子的起始电位约为－0.4 V; 另一种是晶格氧离子形成的深能级表面态(S_c), 能级位于带隙中部, 起电子-空穴对复合中心的作用. 二者对光生电子的捕获效率与电解液pH值及电极电位(U)有关. 高于0.4 V的电位能够显著增大光生载流子的传输速率, 降低TiO₂薄膜费米能级(E_Fn), 有效抑制表面态对光生电子的捕获, 进而提高阳极光电流的大小和稳定性.     

Synthesis of N-doped TiO2 particles from aquaethylenediaminetitanium(IV) hydroxide complex and their optical properties on dye-sensitized solar cells

To promote the photoelectric conversion efficiency of solar cell, N-doped TiO₂ particles are introduced as working electrodes in dye-sensitized solar cells. The N-doped TiO₂ particles (N–en–TiO₂) are easily synthesized from [Ti(NH₂CH₂CH₂NH₂) _x (H₂O) _y ]zOH (aquaethylenediaminetitanium(IV) hydroxide) complex using a modified sol–gel process. The produced N–en–TiO₂ particles show rice-shapes of 25–50 nm and their band-gaps become to be shorter than that of TiO₂. The N–en–TiO₂ particles are applied to working electrode layers in dye-sensitized solar cells, and on comparing the performances of pure TiO₂ and N–en₂–TiO₂–DSCs, the latter shows good performance with a solar energy conversion efficiency of ~5.54 % versus the former of 4.21 % respectively with a notable photocurrent enhancement. Particularly, the N–en₂–TiO₂–DSCs exhibit relatively low charge transfer resistance at counter electrode and electron transfer resistance from dye/TiO₂/photoanode, slower recombination times, faster electron transport times, and higher electron diffusion coefficients than non-doped TiO₂–DSCs.     

Gold particles supported on self-organized nanotubular TiO2 matrix as highly active catalysts for electrochemical oxidation of glucose

Au/TiO₂/Ti electrode was prepared by a two-step process of anodic oxidation of titanium followed by cathodic electrodeposition of gold on resulted TiO₂. The morphology and surface analysis of Au/TiO₂/Ti electrodes was investigated using scanning electron microscopy and EDAX, respectively. The results indicated that gold particles were homogeneously deposited on the surface of TiO₂ nanotubes. The nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm in diameter, and the electrode surface was covered by gold particles with a diameter of about 100–200 nm which are distributed evenly on the titanium dioxide nanotubes. This nanotubular TiO₂ support provides a high surface area and therefore enhances the electrocatalytic activity of Au/TiO₂/Ti electrode. The electrocatalytic behavior of Au/TiO₂/Ti electrodes in the glucose electro-oxidation was studied by cyclic voltammetry. The results showed that Au/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the glucose oxidation than that of gold electrode.     

Photoelectro‐Synergistic Catalysis at Ti/TiO2/PbO2 Electrode and Its Application on Determination of Chemical Oxygen Demand

In this paper, photoelectro‐synergistic catalysis oxidation of organics in water on Ti/TiO₂/PbO₂ electrode was investigated by the method of electrochemistry. Furthermore, the results were compared with those obtained from photocatalysis and electrocatalysis. The method proposed was applied to determine the chemical oxygen demand (COD) value, Ti/TiO₂/PbO₂ electrode functioning as the work electrode during the process. It was shown that the method of photoelectro‐synergistic catalysis had lower detection limit and wider linear range than the methods of electroassisted photocatalysis and electrocatalysis. The results obtained by the proposed method and conventional one were compared by carrying out the experiment on 8 wastewater samples. The correlation of the results using different methods was satisfactory and the relative bias was below ±6.0%.     

Photoelectrochemistry of TiO2 particles: efficient electron transfer from the TiO2 particles to a redox enzyme

Electron transfer from photoexcited TiO₂ particles to dissolve oxygen (O₂), and then to an active center of superoxide dismutase (SOD), was investigated by a slurry electrode technique. As a result of electron transfer, the superoxide anion (O₂⁻) was formed initially, and was then further converted effectively into H₂O₂ by SOD catalysis. At a constant applied potential of 0.6 V (vs. SCE), an increase in photocurrent resulting from oxidation of O₂⁻ and H₂O₂ on a SnO₂ working electrode was observed. However, such an increase in photocurrent decreased rapidly on the addition of catalase, which is a scavenger of H₂O₂.     

The Primary Origin of Excellent Dielectric Properties of (Co,Nb) Co-Doped TiO2 Ceramics: Electron-Pinned Defect Dipoles vs. Internal Barrier Layer Capacitor Effect

(Co, Nb) co-doped rutile TiO₂ (CoNTO) nanoparticles with low dopant concentrations were prepared using a wet chemistry method. A pure rutile TiO₂ phase with a dense microstructure and homogeneous dispersion of the dopants was obtained. By co-doping rutile TiO₂ with 0.5 at.% (Co, Nb), a very high dielectric permittivity of ε′ ≈ 36,105 and a low loss tangent of tanδ ≈ 0.04 were achieved. The sample–electrode contact and resistive outer-surface layer (surface barrier layer capacitor) have a significant impact on the dielectric response in the CoNTO ceramics. The density functional theory calculation shows that the 2Co atoms are located near the oxygen vacancy, creating a triangle-shaped 2CoV_oTi complex defect. On the other hand, the substitution of TiO₂ with Nb atoms can form a diamond-shaped 2Nb2Ti complex defect. These two types of complex defects are far away from each other. Therefore, the electron-pinned defect dipoles cannot be considered the primary origins of the dielectric response in the CoNTO ceramics. Impedance spectroscopy shows that the CoNTO ceramics are electrically heterogeneous, comprised of insulating and semiconducting regions. Thus, the dielectric properties of the CoNTO ceramics are attributed to the interfacial polarization at the internal insulating layers with very high resistivity, giving rise to a low loss tangent.     

Nitrogen-doped TiO2 from TiN and its visible light photoelectrochemical properties

Homogeneous titanium nitride (TiN) thin film was produced by simple electrophoreic deposition process on Ti substrate in an aqueous suspension of nanosized TiN powder. Nitrogen-doped titanium dioxide (TiO_2−xN_x) was synthesized by oxidative annealing the resulted TiN thin film in air. Photoelectrochemical measurements demonstrated visible light photoresponse for the electrode of annealed electrophoreic deposited TiN samples. It is found that the synthesized TiO_2−xN_x electrode showed higher photo potential under white and visible light illumination than the pure TiO₂ electrode. The photocurrent under visible light illumination was also observed, which increased with the increase of deposition time of TiN thin films.     

光诱导约束刻蚀体系中羟基自由基生成的影响因素

采用荧光分析,暂态光电流响应分析,电化学交流阻抗谱(EIS)和Mott-Schottky响应分析考察了外加电位,光照时间,溶液pH等几个关键因素对光诱导约束刻蚀体系中TiO2纳米管阵列表面游离OH生成的影响.结果表明:当外加电位为1.0 V时,光电协同产生游离OH效率最高;OH的光催化生成与消耗能很快达到稳态,形成稳定的约束刻蚀剂层,有利于保持刻蚀过程中的精度;当pH为10时,TiO2纳米管光催化产生游离OH效率最高.研究结果对于调控和优化光诱导约束刻蚀平坦化铜的溶液体系,提高铜的刻蚀速度或平坦化精度有重要的指导意义.     

Artificial photosynthesis by using chloroplasts from spinach adsorbed on a nanocrystalline TiO2 electrode for photovoltaic conversion

Photovoltaic conversion has been achieved by use of chloroplasts (photosynthetic organs) from spinach adsorbed on a nanocrystalline TiO₂ film on an indium tin oxide (ITO) glass electrode (chloroplast/TiO₂ electrode). The shape of the absorption spectrum of the chloroplast/TiO₂ electrode is almost the same that of a dispersion of the chloroplasts. Absorption maxima of the chloroplast/TiO₂ electrode observed at 430, 475, and 670 nm were attributed to carotenoid and chlorophyll molecules, suggesting that chloroplasts have been adsorbed by the nanocrystalline TiO₂ film on the ITO electrode. The photocurrent responses of chloroplast/TiO₂ electrodes were measured by using a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water and 100 mW cm^?2 irradiation. The photocurrent of the chloroplast/TiO₂ electrode was increased by adding water to the redox electrolyte. The photocurrent responses of chloroplast/TiO₂ electrodes irradiated with monochromatic light (680 nm, the absorption band of photosystem II complexed with evolved oxygen) were measured by use of a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water. A chloroplast/TiO₂ electrode photocurrent was observed only when the redox electrolyte containing water was used, indicating that the oxygen evolved from water by photosystem II in chloroplasts adsorbed by a nanocrystalline TiO₂ film on an ITO electrode irradiated at 680 nm is reduced to water by the catalytic activity of the platinum electrode. The maximum incident photon-to-current conversion efficiency (IPCE) was 0.8 % on irradiation at 670 nm.