自旋阀多层膜的电化学制备及其巨磁电阻效应

采用双槽控电位电沉积法在n-Si(111)基体上以NiFe 薄膜为缓冲层制备了[Ni80Fe20/Cu/Co/Cu]n自旋阀多层膜, 并确定了电沉积的工艺条件. 利用X射线衍射(XRD)表征了自旋阀多层膜的超晶格结构, 研究了NiFe缓冲层对自旋阀生长取向的影响. 采用四探针法研究了各子层厚度对自旋阀巨磁电阻效应的影响, 通过振动样品磁强计(VSM)测试了自旋阀的磁滞回线. 自旋阀的巨磁电阻(GMR)值最初随着铜层厚度的变化并发生周期性振荡, Cu 层厚度为3.6 nm时, GMR 达到最大值,随后逐渐减小. 随着Co层和NiFe 层厚度的增大, GMR 值的变化趋势均为先增大后减小. 当自旋阀的结构为NiFe(25 nm)/[Cu(3.6 nm)/Co(1.2 nm)/Cu(3.6 nm)/NiFe(2.8 nm)]30时, GMR 值可达5.4%, 对应的磁电阻灵敏度(SV)为0.2%·Oe-1, 饱和磁场仅为350 Oe.     

超晶格多层膜的电化学制备、表征及其GMR特性的研究

以半导体Si为衬底,电化学沉积Cu/Co超晶格多层膜,用SEM表征多层膜的断面形貌.XRD研究表明,多层膜的调制波长为20～160 nm时,膜层间发生外延生长.随着调制波长的减小,外延生长对膜层结构的影响越来越明显.当调制波长小于20 nm时,在XRD强衍射峰的两侧出现卫星峰,表明多层膜形成超晶格结构.根据卫星峰位置计算的调制波长与由法拉第定律估算的结果非常接近.多层膜的巨磁电阻(GMR)性能随多层膜周期数的增加而增大;当周期数大于300时,GMR性能基本上不再随周期数变化,说明基体的导电性质对GMR的影响可以忽略.     

[NiFe/Cu/Co/Cu]n纳米多层线的电化学制备及表征

采用电沉积法,在阳极氧化铝(AAO)模板中制备了[NiFe/Cu/Co/Cu]_n多层纳米线.利用扫描电子显微镜(SEM)及透射电子显微镜(TEM)对纳米多层线的表面形貌及结构进行了表征,纳米线阵列高度有序、直径均一、层状结构清晰,NiFe层厚度约40 nm,Cu层厚度约60 nm,Co层厚度约15 nm,各子层厚度可控.利用X射线能谱分析仪(EDS)对纳米多层线NiFe层的成分进行了测试,Ni,Fe的原子比为4:1.利用X射线衍射仪(XRD)对[NiFe/Cu/Co/Cu]_n纳米多层膜和多层线结构进行了测试,多层膜为面心立方(fcc)结构,多层线NiFe层为面心立方(fcc)结构,Cu层为六方密排hcp(100),Co层为面心立方(fcc)结构.与组成、结构完全相同的多层膜相比,[NiFe/Cu/Co/Cu]_n多层纳米线具有更优越的巨磁电阻性能.     

热处理对[NiFe/Cu/Co/Cu]_n多层纳米线磁性能的影响

采用双槽控电位法在阳极氧化铝(AAO)模板中制备了有序均一的[NiFe/Cu/Co/Cu]n多层纳米线阵列,并在不同温度下进行了热处理.利用X射线衍射(XRD)对热处理前后多层线的晶体结构进行了测试.考察了不同退火温度对多层线矫顽力、剩磁比、巨磁电阻(GMR)效应、磁灵敏度的影响.随热处理温度升高,多层纳米线中磁性微晶晶型取向越来越明显,晶体结构更均匀;多层纳米线的矫顽力和剩磁比先增大后减小.300°C下多层纳米线矫顽力达到最大值,GMR最大值可达59%,对应的磁电阻灵敏度(SV)为0.233%Oe-1.     

Co/Cu多层纳米线阵列的制备与磁性能

利用双槽直流电沉积技术在阳极氧化铝(AAO)模板的纳米孔中获得调制波长为50 和200 nm 的Co/Cu多层纳米线, 多层纳米线的调制波长由电沉积时间控制. 运用扫描电子显微镜(SEM)和透射电子显微镜(TEM)表征纳米线的形貌, Co/Cu多层纳米线的长度约20 μm, 直径约80 nm; 用X射线衍射(XRD)研究多层线的结构; 用振动样品磁强计(VSM)测试纳米线阵列的磁性能; 利用可变磁场结合高灵敏度恒流装置研究巨磁电阻(GMR)特性. 结果表明, Co/Cu多层纳米线具有磁各向异性. 当磁场与纳米线平行和垂直时, 调制波长为50 nm的多层线的矫顽力分别为87500 和34200 A·m-1, 而调制波长为200 nm的多层线阵列的矫顽力分别为28600 和8000 A·m-1. 调制波长为50 nm的多层纳米线的磁电阻变化率高达-%, 而调制波长为200 nm的多层线未产生明显的GMR效应.     

纳米金属多层膜与多层纳米线的电化学制备及其表征

分别采用单槽法和双槽法电沉积Cu/Co多层膜.研究了两种电沉积方法制备多层膜的工艺条件,利用电化学方法、XRD和SEM对多层膜进行表征,并对Cu/Co多层膜的巨磁阻性能进行了测试. 采用电沉积多层膜的方法，以多孔铝阳极氧化膜（AAO）为模板,在纳米孔内沉积Cu/Co多层线,采用TEM对多层纳米线进行了表征.     

丁二酸二异辛酯磺酸钠在长链醇/N,N-二甲基甲酰胺体系中临界胶束浓度和热力学函数的微量量热法研究

用微量量热法研究了丁二酸二异辛酯磺酸钠(AOT)在N,N-二甲基甲酰胺(DMF)/长链醇(正戊醇、正己醇、正庚醇、正辛醇)体系中的临界胶束浓度(CMC)和热力学函数( , 和 ). 并分析讨论了醇的浓度、醇中的碳原子数及温度与CMC及热力学参数之间的关系. 结果表明, 在AOT/长链醇/DMF体系中, 当醇中的碳原子数相同且醇的浓度相同时, CMC, , 随温度的升高而增大, 而 随温度的升高而降低|当温度相同且醇中的碳原子数相同时, CMC, , 和 随醇浓度的增加都降低|而当温度相同且醇的浓度相同时, CMC, , 和 随醇中碳原子数的增加都降低.     

PEBAX®2533/PSf中空纤维复合膜制备及阻力性能

采用浸渍涂层法制备了聚醚共聚酰胺(PEBAX®2533)/聚砜(PSf)中空纤维复合膜. 考察了涂层液浓度、 温度和基膜预处理对复合膜结构、 阻力及渗透性能的影响, 并考察了操作压力对膜渗透性能的影响. 实验结果表明, 随着涂层液浓度的增加, 复合膜致密层厚度及阻力增大, 复合膜总阻力及支撑层阻力先增大后减小, CO2渗透速率先减小后增大, 分离系数增大. 随着涂层温度升高, 复合膜致密层厚度及阻力减小, 支撑层阻力增大, 复合膜总阻力先减小后增大, 分离系数和渗透速率先增大后减小. 经过预处理, 复合膜致密层厚度减小、 阻力大幅度减小, CO2渗透速率增大58%, 分离系数略有下降. 复合膜支撑层阻力过大, 尤其是支撑层的致密结构影响复合膜的塑化行为.     

电结晶制Co/Pt多层膜的结构及磁性研究

以单晶Si(111)为基底, 在以P盐[主要成分Pt(NO₂)₂(NH₃)₂]和CoSO₄为主盐的硼酸体系中电结晶Co/Pt多层膜. SEM观察多层膜的断面形貌, 证实多层膜具有周期结构. 经XRD测试, 首次证实了Co-Pt界面上有CoPt₃化合物的存在. 用PPMS测试了多层膜的磁滞回线, 平行于外磁场时膜的矫顽力约为165 Oe, 垂直于外磁场时的矫顽力随Co含量的增加而增加, 最大达到396 Oe. 首次用电结晶方法制得了易磁化轴垂直于膜面的Co/Pt多层膜.     

聚乙二醇负载的二茂铁噁唑啉配体的合成及其应用

报道了聚乙二醇(MeO-PEG)负载的二茂铁噁唑啉衍生的手性N,P和N,S配体的合成. 所得负载N,P配体可以成功应用于银催化的[3+2]环加成反应, 最高取得了97%的对映选择性. 另外聚乙二醇负载二茂铁N,S配体可以成功应用于钯催化的烯丙基取代反应, 取得了90%的ee值. 值得注意是, 聚乙二醇负载形成的催化剂循环使用4次后其催化活性和选择性仍可基本保持.     

电沉积Co-Cu颗粒膜的巨磁电阻效应

从１９８８年Ｂａｉｂｉｃｈ首先在磁性Ｆｅ／Ｃｒ多层膜中发现巨磁电阻效应（ＧＭＲ）以来 ［１］,由于ＧＭＲ本身的科研价值和在磁记录、磁性传感器等方面的广泛应用前景 ,引起了人们的极大关注．继多层膜之后 ,人们在金属颗粒膜如Ｃｏ Ａｇ［２］,Ｃｏ Ｃｕ［３,４］等中也相继发现了巨磁电阻效应．颗粒膜是微颗粒镶嵌于薄膜中所构成的复合材料体系．原则上 ,颗粒的组成与薄膜的组成在制备条件上应互不固溶 ,因此颗粒膜区别于合金、化合物 ,属于非均匀相组成的材料．磁性颗粒膜是磁性粒子分布在非磁性金属材料薄膜中．在磁性颗粒与非…     

半导体Si上电沉积Cu-Co颗粒膜及其巨磁电阻效应

采用电化学沉积方法在半导体Si上制备Cu-Co金属颗粒膜. XRD测试结果表明制备态的薄膜形成了单相亚稳态面心合金结构, 薄膜经退火后, XRD谱图中出现了析出的纯金属Co的衍射峰, 这表明薄膜在退火过程中发生了相分离. TEM测试结果也进一步证实了磁性的Co颗粒从非磁性的铜基体中析出. 随着退火温度的增加, 颗粒膜巨磁电阻(GMR)效应不断增大, 当退火温度为450 ℃时, Co0.20Cu0.80薄膜的巨磁电阻效应达到最大, 磁阻率为8.21％. 之后, 磁阻率又随退火温度的升高而降低. 退火前后样品磁滞回线的变化表明薄膜中发生了从超顺磁性到铁磁性的转变, 矫顽力、剩余磁化强度和饱和磁化强度均随退火温度的增高而逐渐增大. 超顺磁性颗粒的作用导致了GMR－H与M－H曲线的不同.     

Adsorption of myoglobin to Cu(II)-IDA and Ni(II)-IDA functionalized langmuir monolayers: study of the protein layer structure during the adsorption process by neutron and X-ray reflectivity

The structure and orientation of adsorbed myoglobin as directed by metal-histidine complexation at the liquid-film interface was studied as a function of time using neutron and X-ray reflectivity (NR and XR, respectively). In this system, adsorption is due to the interaction between iminodiacetate (IDA)-chelated divalent metal ions Ni(II) and Cu(II) and histidine moieties at the outer surface of the protein. Adsorption was examined under conditions of constant area per lipid molecule at an initial pressure of 40 mN/m. Adsorption occurred over a time period of about 15 h, allowing detailed characterization of the layer structure throughout the process. The layer thickness and the in-plane averaged segment volume fraction were obtained at roughly 40 min intervals by NR. The binding constant of histidine with Cu(II)-IDA is known to be about four times greater than that of histidine with Ni(II)-IDA. The difference in interaction energy led to significant differences in the structure of the adsorbed layer. For Cu(II)-IDA, the thickness of the adsorbed layer at low protein coverage was < or = 20 A and the thickness increased almost linearly with increasing coverage to 42 A. For Ni(II)-IDA, the thickness at low coverage was approximately 38 A and increased gradually with coverage to 47 A. The in-plane averaged segment volume fraction of the adsorbed layer independently confirmed a thinner layer at low coverage for Cu(II)-IDA. These structural differences at the early stages are discussed in terms of either different preferred orientations for isolated chains in the two cases or more extensive conformational changes upon adsorption in the case of Cu(II)-IDA. Subphase dilution experiments provided additional insight, indicating that the adsorbed layer was not in equilibrium with the bulk solution even at low coverages for both IDA-chelated metal ions. We conclude that the weight of the evidence favors the interpretation based on more extensive conformational changes upon adsorption to Cu(II)-IDA.     

The effect of Cu substitution on microstructure and thermoelectric properties of LaCoO(3) ceramics

La(Co, Cu)O(3-δ) ceramics were prepared by pressureless sintering of citrate precursor powders, and their thermoelectric properties were investigated with an emphasis on the influence of Cu doping and phase structure as well as microstructure. It was found that a secondary phase first appeared in the form of a network along the grain boundaries and then changed to dispersion with increasing Cu content, which effectively reduced the lattice thermal conductivity of the materials. The thermal conductivity was only 1.21 W m(-1) K(-1) for the sample LaCo(0.75)Cu(0.25)O(3-δ), being much lower as for the thermoelectric oxide materials. In addition, a small amount of Cu substitution for Co increased the electrical conductivity greatly and the absolute Seebeck coefficient, whose sign was also reversed from negative to positive. The dimensionless figure of merit, ZT, of LaCoO(3-δ) oxides at low and middle temperatures can be remarkably enhanced by substituting Co with Cu.