Multi-walled carbon nanotubes as solid-phase extraction adsorbent for the ultra-fast determination of chloramphenicol in egg, honey, and milk by fused-core C18-based high-performance liquid chromatography–tandem mass spectrometry

In the present work, a high-performance liquid chromatography–tandem mass spectrometry method has been developed for the residue analysis of chloramphenicol (CAP) in several food matrices. Following the addition of D₅-CAP as internal standard, egg, honey, and milk were extracted and cleaned by means of solid-phase extraction, utilizing multi-walled carbon nanotubes as sorbent. The extracts were separated on a Halo fused-core C18 column (50 mm × 2.1 mm, 2.7 μm) and quantified by a 4000 Q-trap mass spectrometer equipped with a TurboIonSpray™ interface using electrospray ionization and multiple-reaction monitoring mode. The method validation was performed according to the criteria of Commission Decision 2002/657/EC. The decision limit (CCα) and detection capability (CCβ) of CAP in milk were calculated for m/z 320.8 > 151.9. Due to the existence of slight signal suppression, quantification was performed by matrix-matched calibration curves, ranging from 0.1 to 100 ng mL⁻¹, with regression coefficients of 0.9993, 0.9998, and 0.9997 for egg, honey, and milk, respectively. Mean recoveries of the CAP ranged from 95.8% to 102.3%, with the corresponding intra- and inter-day variation (relative standard deviation) less than 7.13% and 8.89%, respectively. The limit of detection and limit of quantification of the method were also reported. This method successfully applied to several food matrixes (egg, honey, and milk) and can serve as a monitoring tool to avoid unacceptable levels of residues of CAP entering the food chain.     

Flow cytometric immunoassay for sulfonamides in raw milk

Sulfonamide antibiotics are applied in veterinary medicine for the treatment of microbial infections. For the detection of residues of sulfonamides in milk, a multi-sulfonamide flow cytometric immunoassay (FCI) was developed using the Luminex MultiAnalyte Profiling (xMAP) technology. In this automated FCI, a previously developed biotinylated multi-sulfonamide mutant antibody (M.3.4) was applied in combination with fluorescent beads, directly coated with a sulfathiazole derivative, and streptavidin–phycoerythrin (SAPE) for the detection. With this FCI, at least 11 different sulfonamides could be detected (more than 50% inhibition at the 100 ng mL⁻¹ level) and, after an incubation of 1 h, measurements were rapid (10 s per sample). For the application with raw milk, a 96-well microplate-based filtration step was included into the protocol to remove disturbing milk fat particles. Because of differences in sensitivity towards different sulfonamides, the FCI was considered and validated as a qualitative screening assay. For sulfadoxine, the most applied sulfonamide in Dutch dairy cattle, the detection capability (CCβ) was <50 μg L⁻¹ and this level seems feasible for five other sulfonamides. For sulfadiazine, the CCβ was <200 μg L⁻¹ and this level seems feasible for four other sulfonamides. A major advantage of the applied xMAP-technology, with its 100 different color-coded bead sets, is the possibility to develop multiplex immunoassays for the simultaneous detection of several antibiotics.     

Residue analysis of glucocorticoids in bovine milk by liquid chromatography–tandem mass spectrometry

A sensitive liquid chromatography–tandem mass spectrometry (LC-MS/MS) method for the simultaneous determination of 13 steroidal anti-inflammatory drugs in bovine milk is presented. Due to their weakly acid nature, analytes were separated by ion suppression reversed phase chromatography and detected in positive-ion mode by a high flow electrospray source. Dexamethasone-d4 was used as internal standard. The sample preparation was simple and reliable; it included acidic deproteinization of milk followed by sample enrichment and clean-up, utilizing a C18 solid phase extraction cartridge. Recoveries exceeded 70% with an intra-day precision not larger than 12%. The efficiency of the sample clean-up and internal standardization rendered negligible the matrix effect, estimated by comparing standard and matrix-matched calibration curves. A small-scale reconnaissance was carried out on several raw and whole fresh milk samples. A large number of analyzed samples showed a chromatographic peak, in the retention time window of cortisol, at levels included between its decision limit (CCα) and detection capability (CCβ). As a result of a heat-induced transformation, an isomeric product of triamcinolone was observed during the extract evaporation. Since this rearrangement might occur during the milk pasteurization process, LC-MS/MS and ¹H-NMR investigations were performed out to conclusively differentiate the two isomers. One- and two-dimensional proton NMR spectra were able to identify the transformation product as 9a-fluoro-11b,16a-trihydroxy-17b-hydroxymethyl-D-homoandrosta-1,4-diene-3,17a-dione.     

Optimization of analytical conditions and validation of a fluorescence method for the determination of sulfadiazine in milk

This paper describes optimization and validation of a method for sulfadiazine determination in milk samples based on sulfadiazine derivatization with fluorescamine followed by excitation–emission (fluorescence) measurement. For both the optimization and the validation, a comparison between zero-order and first-order signals has been made, showing the advantages of using first-order signals. In the optimization the effects of the temperature of the derivatization reaction, the amount of fluorescamine and the derivatization time on the instrumental signal (maximum intensity or the net analyte signal) are studied by a factorial experimental design, with the optimal values of these factors which give the highest signal being 22 °C for the reaction temperature, 50 μl fluorescamine and 20 min of derivatization time. The validation of the method under the optimal experimental conditions shows that the analytical method is fit-for-purpose, with values of the capability of detection (CCβ) of 4.3 μg l⁻¹ at a sulfadiazine concentration of zero and with probabilities of a false positive and a false negative of 5%. Around the permitted limit (established for the sulfonamides at 100 μg l⁻¹), CCβ is 112 μg l⁻¹. The precision, as the intermediate reproducibility, was established as 1.2 and 3.3 μg l⁻¹ around 0 and 100 μg l⁻¹, respectively. In the application to milk samples spiked with sulfadiazine a mean recovery of around 90% was obtained with a standard deviation of about 8% (14 samples of different concentrations).     

Determination of antibacterials in animal feed by pressurized liquid extraction followed by online purification and liquid chromatography-electrospray tandem mass spectrometry

A fully automated method has been developed for analysis of eighteen antibacterial compounds, including penicillins, cephalosporins and sulfonamides, in animal feed with limits of quantification in the range 0.25–5.79 μg kg⁻¹. The method is based on pressurized liquid extraction of 3 g homogenized feed with water and online clean-up of 500 μL of the extract with C₁₈HD cartridges. The purified sample was directly analysed by liquid chromatography–electrospray tandem mass spectrometry (SPE–LC–ESI-MS–MS). Chromatographic separation was achieved within 10 min by use of a C₁₂ Phenomenex Hydro-RP reversed-phase analytical column and a mobile phase gradient (water + 0.1% formic acid–methanol + 0.1% formic acid). The method was validated, revealing capability for detection of concentrations as low as 0.09 μg kg⁻¹, decision limits (CCα) and detection capabilities (CCβ) in the range 10–174 μg kg⁻¹ and 22–182 μg kg⁻¹, respectively, and inter-day precision ranging from 0.7 to 8.3%. Recovery, with internal standard correction, was in the range 93–134% for all analytes. The method was then applied to analysis of fifteen feed samples, nine of which contained at least one antimicrobial at concentrations between 0.006 and 1.526 mg kg⁻¹. The performance data and results from the method were compared with those from a previous method developed by our group, using offline SPE, by analyzing the same set of samples by both methods. The online SPE approach resulted in slightly improved sensitivity, with LODs of 0.09–2.12 μg kg⁻¹ compared with 0.12–3.94 μg kg⁻¹ by the offline approach. In general, better recovery was achieved by use of online purification (for 72% of the analytes) and the correlation between the two methods was good. The main advantages of the new online method are rapid and automated sample pre-treatment, and reduction of sample manipulation, enabling high-throughput analysis and highly accurate results. Because of all these characteristics, the proposed method is applicable and could be deemed necessary within the field of food control and safety.     

Open‐tubular capillary electrochromatographic determination of ten sulfonamides in tap water and milk by a metal‐organic framework‐coated capillary column

In this study, a metal‐organic framework (MOF), [Mn(cam)(bpy)], was synthesized and characterized by thermogravimetric analysis, scanning electron microscopy, and Fourier transform infrared spectrometry. An open‐tubular capillary column was fabricated from [Mn(cam)(bpy)] via the amide coupling method. Ten types of sulfonamides were separated through the fabricated capillary column, which showed a good limits of detection (<0.07 μg/mL) and linear ranges (1–100 or 5–100 μg/mL) with a high correlation coefficients (R² > 0.9987). The intra‐day, inter‐day and column‐to‐column relative standard deviations (RSDs) in the migration times ranged from 0.44 to 4.87%, and the peak area RSDs ranged from 0.80 to 7.28%. The developed capillary electrochromatography method can be successfully utilized for the determination of sulfonamides in tap water and milk samples.     

Development and in-house validation of an LC-MS/MS method for the determination of stilbenes and resorcylic acid lactones in bovine urine

Stilbenes and zeranol are nonsteroidal estrogenic growth promoters which are banned in the European Union (EU) for use in food-producing animals by Council Directive 96/22/EC. A liquid chromatography–tandem mass spectrometry (LC-MS/MS) method was developed for the screening and confirmation of stilbenes (diethylstilbestrol, dienestrol, hexestrol) and resorcylic acid lactones (zeranol and its metabolites taleranol and zearalanone as well as the mycotoxins α-zearalenol, β-zearalenol and zearalenone) in bovine urine. The method permits the confirmation and quantification of stilbenes and resorcylic acid lactones at levels below 1 μg L⁻¹ and 1.5 μg L⁻¹, respectively. The validation was carried out according to Commission Decision 2002/657/EC, Chap. 3.1.3 “alternative validation” by a matrix-comprehensive in-house validation concept. Decision limit CCα, detection capability CCβ, recovery, repeatabiliy, within-laboratory reproducibility and the uncertainty of measurement were calculated. Furthermore, a factorial effect analysis was carried out to identify factors that have a significant influence on the method. Factors considered to be relevant for the method in routine analysis (e.g. operator, matrix condition, storage duration of the extracts before measurement, different cartridge lots, hydrolysis conditions) were systematically varied on two levels. The factorial analysis showed that different cartridge lots, storage durations and matrix conditions can exert a relevant influence on the method.     

Quantitative Analysis of Sulfonamide Residues in Natural Animal Casings by HPLC

A multiresidue method has been developed for the simultaneous determination of sulfadiazine, sulfathiazole, sulfapyridine, sulfamerazine, sulfamethoxydiazine, sulfamethylthiazole, sulfamethazine, sulfamonomethoxine, sulfamethoxypyridazine, sulfisoxazole, sulfamethoxazole, sulfadimethoxine and sulfaquinoxaline in natural animal casings by HPLC after solid-phase extraction. The sulfonamides were extracted with acetonitrile and the extract cleaned up with an Oasis MCX SPE cartridge prior to analysis. Separation was on a ZOBAX Eclipse XDB-C₈ column using gradient elution with acetonitrile/methanol/0.1% acetic acid. The effect of separation conditions on chromatographic behavior and recovery has been studied. Calibration graphs were linear with very good correlation coefficients (r = 0.9983−0.9996) in the concentration range from 0.02 to 1 μg mL⁻¹. The limits of quantitation (LOQ) for the 13 sulfonamides were in the range of 1.5–2.2 μg kg⁻¹. Decision limits (CCα) and detection capabilities (CCβ) were in the range of 105.2–111.0 and 113.0–120.2 μg kg⁻¹, respectively. The recovery for casings spiked with 1.5–100 μg kg⁻¹ ranged from 65.2 to 85.9%. The relative standard deviations (RSDs) of the sulfonamides for six measurements at 100 μg kg⁻¹ were from 2.2 to 7.7%. The applicability of the method to the analysis of salted swine casings, salted sheep casings and dry casing samples was demonstrated.     

Development of a novel strategy for preconcentration of antibiotic residues in milk and their quantitation by capillary electrophoresis

A novel analytical method based on capillary zone electrophoresis coupled with diode array detection is developed and validated for the identification and simultaneous quantitation of four antibiotics in bovine raw milk. The studied antibiotics belong to different groups: β-lactams, tetracyclines, quinolones, amphenicols and sulfonamides. An experimental design including both a factorial and a central composite design allowed a reduction in the number of optimization experiments. The multiple response criterion was successfully used to optimize the separation between chloramphenicol, ciprofloxacin, ampicillin, tetracycline and sulfamethoxazol, allowing the reduction of the analysis time with excellent peak resolutions and low capillary current. Different strategies for preconcentration and extraction of the studied antibiotics were applied, in order to remove potential interferences from the sample and to increase the sensitivity. Milk samples were prepared by a clean-up/extraction procedure based on protein precipitation with trichloroacetic acid followed by liquid-liquid extraction with dichloromethane combined with solid-phase extraction, and injection into the electrophoretic system hydrodynamically. The limits of detection and quantification (below 30 and 100 μg L⁻¹, respectively) were in all cases lower than the maximum residue limits tolerated for these compounds in milk. Accuracy was evaluated by computing recoveries for the target antibiotics which were between 93.08% and 102.89%.     

Determination of sulfonamides in food samples by membrane-protected micro-solid phase extraction coupled with high performance liquid chromatography

In the present study, a simple and sensitive extraction method based on polypropylene membrane-protected micro-solid phase extraction (MP-μ-SPE) has been developed for analysis of sulfonamides in food samples. Poly (methacrylic acid-ethylene glycol dimethacrylate) (p-MAA-EDMA) was synthesized using orthogonal array experimental design, optimized with three factors at four levels and evaluated on yield, hydrophobic and cation-exchange properties. The optimized p-MAA-EDMA was then employed as the sorbent in the MP-μ-SPE for extraction of sulfonamides from milk and chicken muscle samples, followed by high performance liquid chromatographic analysis with ultraviolet detection. Under optimized extraction conditions, good linearities (0.010–1.0 μg mL^?1 with r² > 0.9900), low limits of detection (0.38–0.62 ng mL^?1), and acceptable intra-day (2.7–13.7%) and inter-day (6.7–15.2%) relative standard deviations were obtained. It was demonstrated to be an effective approach to handle semi-solid/solid samples with good resistance to interference from “dirty” samples.     

Enzyme-linked immunosorbent assay and colloidal gold immunoassay for sulphamethazine residues in edible animal foods: investigation of the effects of the analytical conditions and the sample matrix on assay performance

To determine sulphamethazine (SMZ) residues in edible animal foods (pig muscle, chicken muscle, egg, fish, milk and liver), a competitive direct enzyme-linked immunosorbent assay (ELISA) and a colloidal gold immunoassay were established. The limits of detection of the ELISA and the colloidal gold immunoassay were 0.02 and 0.5 μg kg⁻¹, respectively. The specificity of the ELISA developed to the SMZ was high according to the results of cross-reactivity testing with 14 kinds of sulphonamides. To obtain a more sensitive immunoassay, buffer solution (30 mmol L⁻¹ phosphate-buffered saline with 0.05% Tween 20, pH 8.5) was optimized through the whole test procedure. A simple and efficient extraction method for the rapid detection of SMZ residues in foods was developed, with recoveries between 74 and 117.5%. Matrix effects can be avoided by 1:10 dilution of pig muscle, chicken muscle, egg, fish, milk and liver with optimal buffer. The detection limit of SMZ was 5 μg kg⁻¹ in liver and 2 μg kg⁻¹ in the other five samples. For the validation of the ELISA tests, sample extracts were analysed by ELISA and high-performance liquid chromatography. The results obtained by these two methods showed a good correlation (r ²) which was greater than 0.9. The colloidal gold immunoassay presented in this assay was successfully applied to determine SMZ in pig muscle, milk and fish below or equal to the maximum residue level (20 μg kg⁻¹).     

Preparation of magnetic molecularly imprinted polymer for rapid determination of bisphenol A in environmental water and milk samples

A magnetic molecularly imprinted polymer (M-MIP) of bisphenol A (BPA) was prepared by miniemulsion polymerization. The morphological and magnetic characteristics of the M-MIP were characterized by Fourier-transform infrared spectroscopy, transmission electron microscopy, and vibrating sample magnetometry. The adsorption capacities of the M-MIP and the nonimprinted polymer were investigated using static adsorption tests, and were found to be 390 and 270 mg g⁻¹, respectively. Competitive recognition studies of the M-MIP were performed with BPA and the structurally similar compound DES, and the M-MIP displayed high selectivity for BPA. A method based on molecularly imprinted solid-phase extraction assisted by magnetic separation was developed to extract BPA from environmental water and milk samples. Various parameters such as the mass of sorbent, the pH of the sample, the extraction time, and desorption conditions were optimized. Under selected conditions, extraction was completed in 15 min. High-performance liquid chromatography with UV detection was employed to determine BPA after the extraction. For water samples, the developed method exhibited a limit of detection (LOD) of 14 ng L⁻¹, a relative standard deviation of 2.7% (intraday), and spiked recoveries ranging from 89% to 106%. For milk samples, the LOD was 0.16 μg L⁻¹, recoveries ranged from 95% to 101%, and BPA was found in four samples at levels of 0.45–0.94 μg L⁻¹. The proposed method not only provides a rapid and reliable analysis but it also overcomes problems with conventional solid-phase extraction (SPE), such as the packing of the SPE column and the time-consuming nature of the process of loading large-volume samples.     

HPLC determination of cefotaxime and cephalexine residues in milk and cephalexine in veterinary formulation

An HPLC method was developed and validated for the determination of the cephalosporins cefotaxime and cephalexine in skimmed bovine milk. The analytical column, Kromasil C₁₈ (250 mm × 4.0 mm, 5 μm) was operated at ambient temperature. Mobile phase consisted of CH₃OH-acetate buffer (pH = 4.0) and it was delivered isocratically at a flow rate of 1.0 mL · min⁻¹. Total analysis time was less than 5 min. Caffeine was used as internal standard (5 ng · μL⁻¹). UV detection was performed at 265 nm. Method validation was performed by means of intra-day (n = 5) and inter-day accuracy and precision (n = 8), sensitivity and linearity. Limits of detection (LOD) and limits of quantification (LOQ) were 0.1 and 0.3 ng · μL⁻¹, respectively. The method was applied to the analysis of a veterinary drug (CEPOREX) containing cephalexine. The results were quite accurate with the relative error varying from −8.0 to −3.5%. Solid-phase extraction was applied to remove all matrix interference from milk samples. High extraction recoveries (average 84–121%) were achieved by using Abselut NEXUS cartridges with acetonitrile as eluent and a rinsing step with water and n-butanol. A pre-concentration step was necessary in a 1/10 level to reach the EU MRL concentration level (100 μg · kg⁻¹). RSD values were less than 7% for both cephalosporins. Correspondence: Ioannis N. Papadoyannis, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University of Thessaloniki, GR-54124 Thessaloniki, Greece     

Fast Determination of Residual Sulfonamides in Milk by In-Tube Solid-Phase Microextraction Coupled with Capillary Electrophoresis-Laser Induced Fluorescence

A fast, feasible, eco-friendly method for determination of sulfonamides using in-tube solid-phase microextraction (IT-SPME) coupled with capillary electrophoresis-laser induced fluorescence was developed. The graphene-embedded porous polymer monolithic column prepared via in-situ UV polymerization was proposed as the IT-SPME column. The method was applied to determine residual sulfonamides in a real milk sample, and an amount of 3.7 ng mL^?1 sulfamethazine was detected, which was much lower than the maximum residue limit.     

Room temperature fabrication of magnetic covalent organic frameworks for analyzing sulfonamide residues in animal-derived foods

A magnetic solid phase extraction method based on magnetic covalent organic frameworks (TpBD@Fe₃O₄; 2,4,6-triformylphloroglucinol (Tp) and benzidine (BD)) combined with high performance liquid chromatography has been developed to detect the sulfonamides including sulfadiazine, sulfamerazine, sulfamethazine, and sulfamethoxazole in milk and meat. TpBD@Fe₃O₄ were synthesized at room temperature under mild reaction conditions with a simple and rapid operation. The TpBD@Fe₃O₄ exhibited higher extraction efficiency because of the π–π and electrostatic interactions between the benzene ring structure of the TpBD and the sulfonamide molecules. The extraction conditions including the dosage of adsorbents, the type and dosage of eluent, the elution time, and the pH of the sample solution were fully optimized. The detection results showed good linearity over a wide range (50–5 × 10⁴ ng/mL) and low detection limits (3.39–5.77 ng/mL) for the sulfonamide targets. The practicability of this magnetic solidphase extraction-high-performance liquid chromatography method was further evaluated by analyzing milk and meat samples, with recoveries of the targets of 71.6–110.8% in milk and 71.9–109.7% in pork. The successful detection of sulfonamides residues has demonstrated the TpBD@Fe₃O₄ excellent practical potential for analyzing pharmaceutical residues in animal-derived foods.     

甲氧苄啶分子印迹涂层搅拌棒在复杂样品痕量甲氧苄啶和磺胺药物分析中的应用(英文)

研制了甲氧苄啶分子印迹吸附萃取搅拌棒涂层,并应用于复杂样品中痕量甲氧苄啶和磺胺药物的分析。分子印迹涂层的厚度约为21.5μm,相对标准偏差为5.9%(n=10),涂层均匀、致密,具有良好的热稳定性和化学稳定性。分子印迹涂层的萃取容量是非印迹涂层萃取容量的1.7倍,分子印迹涂层对抗菌增效剂、磺胺药物、三嗪化合物和甲氨蝶呤都表现出良好的选择性吸附萃取能力。建立了分子印迹吸附萃取搅拌棒联用高效液相色谱的分析方法,成功应用于加标尿样和血浆中痕量甲氧苄啶的分析,线性范围为5～200μg/L,检出限为1.6μg/L,在尿样和血浆中的回收率范围分别为84.5%～91.7%和71.9%～85.1%,标准偏差分别为2.9%～4.4%和3.0%～7.3%。该方法还应用于加标牛奶中痕量磺胺药物的分析,线性范围为10～200μg/L,检出限在4.5～6.1μg/L之间,回收率为83.2%～110.2%,标准偏差为4.1%～8.0%.     

Selective Determination of Sulfonamide Residues in Honey by SPE-RP-LC with UV Detection

Solid-phase extraction was used to isolate sulfacetamide, sulfathiazole, sulfapyridine, sulfamerazine, sulfamethoxypyridazine and sulfamethoxazole from honey. The optimized procedure used polymeric Abselut Nexus cartridges and the sulfonamides were separated, in the isocratic mode, on an Inertsil ODS-3 (250 × 4 mm I.D., 5 μm) column, using methanol-0.05 M acetate buffer (pH 3.6) (20:80 v/v) with 1% (v/v) of acetic acid, UV detection at 263 nm and a flow-rate of 1 mL min⁻¹. Caffeine was used as internal standard. Average recoveries of the analytes from spiked honey ranged from 80 to 117% and the detection limits based on a spiked honey extract were 20–25 μg kg⁻¹.     

固相萃取-高效液相色谱法同时测定牛奶中22种磺胺类兽药残留

建立了一种基于固相萃取技术同时测定牛奶中22种磺胺类兽药残留的高效液相色谱分析方法.样品经乙腈-甲酸混合溶液提取,乙腈饱和的正己烷除酯后,HLB固相萃取柱净化,以甲醇-2 mmol/L乙酸铵(含0.2％乙酸)为流动相进行梯度洗脱,XBridge C18色谱柱进行分离,采用光电二极管阵列检测器检测,外标法定量.磺胺类化合...     

Matrix solid phase dispersion–Soxhlet simultaneous extraction clean-up for determination of organochlorine pesticide residues in tobacco

A novel method combining matrix solid phase dispersion (MSPD) with Soxhlet simultaneous extraction clean-up (SSEC) was developed. Being a single-step extraction and clean-up procedure, it could be used instead of multistep solvent extraction and Florisol column clean-up. It not only reduces sample contamination during the procedure, but it also decreases the amount of organic solvent needed. The retention times of standards were used to qualitatively assess the method, and the external standard method was used to quantitatively assess it. Residues of organochlorine pesticides (OCP) in tobaccos were determined by gas chromatography–electron capture detection (GC–ECD), and their identities were confirmed by the standard addition method (SAM). The performance of the method was evaluated and validated: the detection limit was 0.01–0.02 μg g⁻¹, relative standard deviations were 5–26%, and recoveries were 72–99% at fortification levels of 0.10, 1.00 and 10.0 μg g⁻¹. The analytical characteristics of MSPD–SSEC compared very favorably with the results from the classical multistep solvent extraction and Florisol column clean-up method.     

Optimization of a solid-phase extraction procedure in the fluorimetric determination of sulfonamides in milk using the second-order advantage of PARAFAC and D-optimal design

The objective of this work is to optimize a solid-phase extraction procedure for the simultaneous determination of sulfadiazine, sulfamerazine, and sulfamethazine in milk by fluorimetric detection. For this task, an alternative strategy is employed, which allows one to reduce noticeably the number of experiments without losing the quality of the estimations. It consists of the use of a D-optimal design together with PARAFAC decomposition for the calculation of the response in the experimental design. Effects of amount of cartridge sorbent, kind of milk, volume of conditioning solutions, kind of wash and elution, and kind of mixture of sulfonamides have been evaluated, for maximizing sulfonamide mean recovery and minimizing its standard deviation. Since milk without sulfonamides may give some matrix effect over the fluorescence signal, its behavior has also been studied. Optimal conditions have been selected where the ratio between sulfonamide recovery and milk without sulfonamides was the highest, which are 500 mg of cartridge sorbent, acid wash, and elution and 3 mL of conditioning solutions. The type of milk and mixture of sulfonamides not significant. This makes the procedure suitable for the combined determination of sulfadiazine, sulfamerazine, and sulfamethazine in any kind of milk. Finally, an experimental procedure is proposed, obtaining a sulfonamide mean recovery equal to 68.5% with values of standard deviation between 7 and 8 μg kg⁻¹.