基于能量转换原理的磁电层合材料低频磁电响应分析

提出了一种基于能量转换原理的磁致伸缩/压电层合材料低频磁电响应模型,并对不同层合结构的磁电响应特性进行了对比研究.该模型假定层合材料层间能量传递通过层间剪切力来实现,利用应力函数法分析了磁致伸缩层和压电层的应力与应变,求出了磁致伸缩层的应变能和存储磁场能以及压电层的应变能和电场能;利用Hamilton最小能量原理求出了层间剪切力的大小,获得了开路状态下层合材料的低频磁电响应模型.发现磁电电压系数与磁致伸缩材料的磁导率、泊松比、磁机耦合系数以及压电材料的泊松比、机电耦合系数等有关,并对这些参数的影响进行了分析.同时对两层和三层结构的层合材料磁电特性进行了对比研究,发现层合结构不同则获得的磁电系数公式不同,用相应的公式计算得到的误差才会最小.研究结果表明,本文的理论误差小于6.5%,与其他方法相比,本文的理论模型能更好地描述磁电层合材料的低频磁电响应特性.     

复合圆环弯曲振动四极子模态分析

针对压电圆环弯曲振动机电转换性能较差的问题,提出了一种复合圆环弯曲振动换能器,它由一个径向极化的压电陶瓷内圆环和一个金属外圆环复合而成。基于能量原理推导得到了复合圆环弯曲振动的谐振频率和有效机电耦合系数,探讨了弯曲振动四极子模态特性与其结构尺寸间的关系。当压电圆环尺寸不变时,随外侧金属圆环壁厚增加,复合圆环弯曲振动四极子模态谐振频率上升,有效机电耦合系数迅速上升到极大值后缓慢下降。最后,设计制作了圆环换能器并对其谐振频率和有效机电耦合系数进行了实验测试,测试结果与解析结果和数值模拟结果吻合得较好。      

磁致伸缩/压电叠层复合材料磁-机-电耦合系数分析

分析和推导了磁致伸缩/压电叠层复合材料的机-电耦合系数、磁-机耦合系数及磁-电耦合系数与磁致伸缩层和压电层性能参数及几何参数之间的关系.进一步分析表明,叠层复合材料低频时的磁电电压系数正比于磁-电耦合系数,谐振时的磁电电压系数正比于磁-电耦合系数与机械品质因素的乘积;磁电电压系数还与复合结构的本征阻抗有关,本征阻抗越大磁电电压系数越大.通过性能差异较大的Terfenol-D和FeNi基弹性合金分别与压电材料PZT5-H和PZT8相互组合构成复合材料的比较分析,进一步阐明了磁电复合材料磁-电耦合系数和机械品 关键词： 磁电效应 磁-机-电耦合系数 磁致伸缩材料 压电材料     

Definition and measurement of the normalized electrical impedance of lossy piezoelectric resonators for ultrasonic transducers

Relevant equivalent circuit parameters and values of material constants of a piezoelectric resonator can be determined from measurements of its electrical input impedance as a function of frequency. The complex electrical impedance curves and the associated critical frequencies are the basis of this characterization by the piezoelectric resonance method. In this paper, the previously introduced concept of normalized electrical impedance of the lossy resonator, extended to include piezoelectric losses, is applied to the analysis of the effects of different types of intrinsic losses on peak values, bandwidths and characteristic frequencies. The resulting impedance patterns depend solely on the electromechanical coupling coefficient and the loss tangents, providing a useful tool for the analysis of low-Q resonators. The normalized impedance is experimentally evaluated from the basic data provided by an HP 4194A impedance analyser by means of specifically developed ASP programs.     

对称磁电层合板磁电转换效应理论研究

磁致伸缩和压电层合材料通过磁致伸缩和压电效应的乘积可以获得大的磁电效应.通过材料的力学本构方程，建立了对称磁电层合板磁电耦合的静态力学模型；采用ANSYS 80多物理场有限元分析软件，对层合结构的磁电转化效应进行了数值计算，并与理论计算值进行了对比.研究结果表明：磁致伸缩/压电的厚度比增加使磁电电压系数增大；所推导的磁电电压系数公式的计算值与等效电路模型推导的公式计算值符合很好；有限元数值计算结果介于两种模型的计算结果之间. 关键词： 磁电效应 层合板 本构方程 有限元分析     

Investigations of thickness-shear mode elastic constant and damping of shunted piezoelectric materials with a coupling resonator

Shear-mode piezoelectric materials have been widely used to shunt the damping of vibrations where utilizing surface or interface shear stresses. The thick-shear mode(TSM) elastic constant and the mechanical loss factor can change correspondingly when piezoelectric materials are shunted to different electrical circuits. This phenomenon makes it possible to control the performance of a shear-mode piezoelectric damping system through designing the shunt circuit. However, due to the difficulties in directly measuring the TSM elastic constant and the mechanical loss factor of piezoelectric materials, the relationships between those parameters and the shunt circuits have rarely been investigated. In this paper, a coupling TSM electro–mechanical resonant system is proposed to indirectly measure the variations of the TSM elastic constant and the mechanical loss factor of piezoelectric materials. The main idea is to transform the variations of the TSM elastic constant and the mechanical loss factor into the changes of the easily observed resonant frequency and electrical quality factor of the coupling electro–mechanical resonator. Based on this model, the formular relationships are set up theoretically with Mason equivalent circuit method and they are validated with finite element(FE) analyses. Finally, a prototype of the coupling electro–mechanical resonator is fabricated with two shear-mode PZT5 A plates to investigate the TSM elastic constants and the mechanical loss factors of different circuit-shunted cases of the piezoelectric plate. Both the resonant frequency shifts and the bandwidth changes observed in experiments are in good consistence with the theoretical and FE analyses under the same shunt conditions. The proposed coupling resonator and the obtained relationships are validated with but not limited to PZT5 A.     

Effect of photoconductivity and dielectric constant of the photorefractive materials on two-beam coupling gain and phase-shifts for a single unidirectional photorefractive ring resonator

Photoconductive dependence of two-beam coupling between the pump beam and the signal beam in photorefractive materials have been analyzed in case of non-degenerate wave mixing under the undepleted pump approximation method. During the two-wave mixing in photorefractive materials, steady state amplification of the signal beam and oscillation characteristics of a single unidirectional ring resonator has been studied. The domination of the two-beam coupling gain over the combined absorption and resonator losses such as Fresnel reflections from the crystal and imperfect mirrors builds up unidirectional oscillation. The buildup of such an oscillation leads to a saturation of the gain, which can be explained in terms of the photorefractive phase-shift. The existence of this phase-shift between the photorefractive index grating and the illumination intensity pattern, which is of characteristic of the photorefractive effect, leads to an energy transfer between the two beams. For a single unidirectional ring resonators, the effects of photoconductivity of the materials, two-beam energy coupling coefficient, dielectric constant, crystal thickness, and material's absorption coefficient on amplification of the two-beam coupling gain and photorefractive phase-shifts of the signal beam have also been studied in detail. It has been found that amplification of the signal beam and phase-shift can be enhanced by taking the photorefractive crystal having higher photoconductivity and lower dielectric constant, which improves performance of the resonators.     

Stoney formula for piezoelectric film/elastic substrate system

With the trends in miniaturization, and particularly the introduction of micro- and nano-electro-mechanical system,piezoelectric materials used in microelectronic devices are deposited usually in the form of thin film on elastic substrates.In this work, the bending of a bilayer comprising a piezoelectric film deposited on an elastic substrate, due to the mismatch,is investigated. An analytic formula relating the curvature of the bilayer to the mismatch, the electroelastic constants and the film thickness is obtained, and from this formula, a transverse piezoelectric constant d_31 can be estimated. Meanwhile the influence of electromechanical coupling coefficient on the curvature is discussed.     

径向复合圆柱压电超声换能器

提出一种三元径向复合圆柱压电超声换能器,并对其径向振动特性进行了研究。基于弹性力学理论及机电类比原理,导出了柱坐标系中分割处理径向极化压电陶瓷管准厚度模振动及薄壁短圆管径向振动的机电等效电路;利用径向力和振速连续的边界条件,得出了径向复合圆柱压电换能器系统的径向振动机电等效电路及其共振频率方程。探讨了换能器径向共振频率及有效机电耦合系数随其几何尺寸的变化关系。研究表明,换能器的径向共振频率及有效机电耦合系数随其内芯半径和预应力管壁厚度增大而降低。研制了一些径向复合圆柱压电换能器,并对其径向共振频率进行了测试。结果表明,理论与实验结果基本一致。      

基于2-2型压电复合材料的新型宽频带径向振动超声换能器

本文提出了一种基于2-2型压电复合材料的新型宽频带径向振动超声换能器,它主要由内金属圆环和外压电陶瓷复合材料圆环组成.首先利用Newnham串并联理论和均匀场理论推导了2-2型压电复合材料的等效参数;其次利用解析法得到了金属圆环和径向极化压电复合陶瓷圆环径向振动的机电等效电路;最后得到了换能器的六端机电等效电路,从而得到了换能器的频率方程.接着分析了换能器共振频率和反共振频率以及有效机电耦合系数与几何尺寸、两相体积占比的关系,采用仿真软件对新型换能器的径向振动进行了数值模拟.结果表明,利用解析法得到的共振频率和反共振频率与数值模拟结果吻合较好.此外,对换能器在水下的辐射声场进行了仿真研究,结果表明新型复合材料径向换能器相比传统纯陶瓷径向换能器,发射电压响应幅值更大,工作带宽提高接近一倍,声匹配更佳.     

The physics of magnetoelectric composites

This paper gives an overview about the basic ideas of magnetoelectric materials. Up to now single-phase materials show the magnetoelectric effect only below room temperature. Mixing a magnetostrictive with a piezoelectric component is a way to overcome this limitation. This delivers a composite which can exhibit a magnetoelectric effect even at room temperature and higher. Possible candidates for these composites (piezoelectric as well as magnetostrictive) are shown, examples from literature and own results are given. The most important coupling mechanism (magnetization, magnetostriction, local stress, charge) between the magnetostrictive and the piezoelectric phase are discussed. Hints for a direct coupling between the electric polarization and the magnetization are also presented. Different measurement methods for determining the magnetoelectric coefficient are discussed. Representative results as obtained on a technical useful composite between 50% Co-Ferrite+50% BaTiO₃ are given. The behavior of a simple “mixed” structure with that of a “core-shell” structure is compared. The later gives a 20-times larger magnetoelectric coefficient.     

考虑损耗的磁致/压电层合材料谐振磁电响应分析

运用等效电路法，对磁致/压电层合材料谐振状态下的磁电响应进行分析，得到了材料在谐振状态下的磁电电压转换系数理论计算公式. 详细地分析了磁致/压电层合材料在谐振点附近的磁损耗、机械损耗、电损耗，并给出了各种损耗相应的计算方法和大小，发现谐振状态下，材料的主要损耗来源于机械损耗. 分析结论较好地解释了磁电层合材料在不同偏置磁场下磁电响应的实验结果. 关键词： 磁致/压电层合材料 磁电效应 谐振 损耗分析     

一种高灵敏压电平面水声换能器

设计并制作了一种高灵敏压电平面水声换能器。该换能器敏感元件是对1-3-2型压电复合材料结构的改进,即在带基底的压电陶瓷小柱阵列间不注入聚合物,并在其上表面直接覆盖金属板,构成“带基底的压电小柱阵列+金属盖板”结构敏感元件(称为“空气填充型”敏感元件)。对“空气填充型”敏感元件的谐振频率进行了理论计算和有限元仿真,与实测结果较吻合。为便于对比性能,同时制作了同尺寸“1-3-2型压电复合材料+金属盖板”结构敏感元件(称为“聚合物填充型”敏感元件)换能器。分别对“空气填充型”和“聚合物填充型”敏感元件换能器的有效机电耦合系数、发送电压响应和接收灵敏度进行有限元仿真和实测,结果均显示,“空气填充型”敏感元件换能器具有较高的接收灵敏度,相较于“聚合物填充型”敏感元件换能器可提高21 dB。该敏感元件换能器能有效提高灵敏度,可为研制高灵敏换能器提供参考。      

Equivalent circuit of a composite acoustic resonator for microwave radioelectronic devices

On the basis of analyzing the expression for the input electric impedance of a composite microwave acoustic resonator, its equivalent electric circuit is constructed. It is shown that, for high-order harmonics, the difference between the antiresonance and resonance frequencies is determined not only by the electromechanical coupling coefficient, but also by the loss in the structure. The conditions under which this difference corresponds to the bandwidth of the equivalent parallel electric oscillatory circuit are formulated. Expressions for the resonance and antiresonance frequencies are derived. The procedures of determining the Q factor and the electromechanical coupling coefficient from the measured resonance and antiresonance frequencies of the structure are justified.     

Electromechanical response of 2-2 layered piezoelectric composites: A micromechanical model based on the asymptotic homogenization method

A micromechanical model based on the asymptotic homogenization technique has been developed to predict the complete elastic, dielectric and piezoelectric properties of a general 2-2 layered piezoelectric composite where the constituent phases are elastically anisotropic and piezoelectrically active. Two classes of layered piezoelectric composites (i.e. longitudinally and transversely layered) are considered in two widely different ceramic- and polymer-based systems and their effective properties are obtained in the limits of both large-volume (i.e. bulk) and small-volume (i.e. thin-film) systems. It is demonstrated that: (i) in the bulk, ceramic–ceramic layered composite system, the elastic, piezoelectric, and dielectric properties of the composites vary linearly with volume fraction of the second phase, while in the bulk ceramic–polymer layered composite system, the corresponding properties vary non-linearly with volume fraction of the second phase; (ii) in the prismatic (thin-film) layered piezoelectric composite system, the non-vanishing, effective elastic, piezoelectric and dielectric properties vary linearly with the volume fraction of the second phase for both the longitudinally and transversely layered composite structures in the ceramic–ceramic and the ceramic–polymer composite systems; (iii) the ceramic–polymer piezoelectric layered composites that incorporate a low density polymeric phase with lower acoustic impedance generally exhibit enhanced piezoelectric coupling constants and lowered acoustic impedance; (iv) the longitudinally layered composites exhibit higher piezoelectric coupling constants and lower acoustic impedance compared to that of the transversely layered composites; and (v) the best combination of properties for applications such as hydrophones (i.e. the highest piezoelectric coupling constants and the lowest acoustic impedance) is obtained in the ceramic–polymer, longitudinally layered, thin-film, piezoelectric composites.     

Optimal magnetoelectric coupling performance of Terfenol-D/PZT composites in resonance state under bias magnetic field

Laminated magnetoelectric (ME) composites with various thickness ratios were optimized, fabricated and experimentally investigated in this work. The Terfenal-D/PZT specimens with optimal thickness ratio between the magnetostrictive phase and piezoelectric phase, and two other values were tested for their ME coupling performance. The coupling voltage output increases linearly with the increase of DC bias magnetic field. The ME voltage coefficient increases more than 100 times in the resonance state for the optimal laminate. The DC bias magnetic field affects the ME voltage coefficient significantly, and also has little effect on the resonant frequency. The strength of AC magnetic field also slightly affects the ME voltage coefficient in resonance state, but does not affect the resonant state under which the same DC magnetic field is required. The experimental results can help understand the coupling performance of ME composite under bias magnetic field and prompt the application of ME devices.     

A multiple degree of freedom electromechanical Helmholtz resonator

The development of a tunable, multiple degree of freedom (MDOF) electromechanical Helmholtz resonator (EMHR) is presented. An EMHR consists of an orifice, backing cavity, and a compliant piezoelectric composite diaphragm. Electromechanical tuning of the acoustic impedance is achieved via passive electrical networks shunted across the piezoceramic. For resistive and capacitive loads, the EMHR is a 2DOF system possessing one acoustic and one mechanical DOF. When inductive ladder networks are employed, multiple electrical DOF are added. The dynamics of the multi-energy domain system are modeled using lumped elements and are represented in an equivalent electrical circuit, which is used to analyze the tunable acoustic input impedance of the EMHR. The two-microphone method is used to measure the acoustic impedance of two EMHR designs with a variety of resistive, capacitive, and inductive shunts. For the first design, the data demonstrate that the tuning range of the second resonant frequency for an EMHR with non-inductive shunts is limited by short- and open-circuit conditions, while an inductive shunt results in a 3DOF system possessing an enhanced tuning range. The second design achieves stronger coupling between the Helmholtz resonator and the piezoelectric backplate, and both resonant frequencies can be tuned with different non-inductive loads.     

Elastic properties of spherically anisotropic piezoelectric composites

Effective elastic properties of spherically anisotropic piezoelectric composites, whose spherically anisotropic piezo-electric inclusions are embedded in an infinite non-piezoelectric matrix, are theoretically investigated. Analytical solutions for the elastic displacements and the electric potentials under a uniform external strain are derived exactly. Taking into account of the coupling effects of elasticity, permittivity and piezoelectricity, the formula is derived for estimating the effective elastic properties based on the average field theory in the dilute limit. An elastic response mechanism is revealed, in which the effective elastic properties increase as inclusion piezoelectric properties increase and inclusion dielectric properties decrease. Moreover, a piezoelectric response mechanism, of which the effective piezoelectric response vanishes due to the symmetry of spherically anisotropic composite, is also disclosed.     

Tunable bulk acoustic wave resonators with the induced piezoelectric effect in a ferroelectric

An electromechanical model of the piezoelectric effect induced in an acoustic resonator based on a ferroelectric film under the action of a dc or weak ac voltage is developed. The basic equation is obtained by expansion of the free energy in a series with respect to the electric induction and the mechanical deformation. The system of electromechanical equations for variable components of the induction and the mechanical deformation involves all linear terms along with the component of the electrostriction nonlinear with respect to the mechanical deformation. These electromechanical equations made it possible to obtain a one-dimensional approximation for the effective parameters of the material: the piezoelectric modulus and the elastic modulus as a function of the strength of the electric field applied to the acoustic layer. Expressions for the controlled electromechanical coupling coefficient and resonance frequencies of the tunable acoustic resonator are found. It is shown that the most significant parameter responsible for the tuning is the nonlinear electros-triction coefficient M, whose magnitude and sign were evaluated from the available experimental data.     

Calculation of acoustic energy trapping in resonators based on isotropic and nanoceramic materials

The problem of acoustic energy trapping in a microwave resonator structure operating on the basis of acoustic waves and containing a relatively thick nanoceramic plate, which has a piezoelectric film with electrodes on its surface, is solved. For a composite resonator structure made on the basis of isotropic substrates and nanoceramics, formulas are derived that allow one to choose the thicknesses of its layers to obtain a high Q factor at a desired frequency.