Structural and optical properties of Mn-doped ZnO nanocrystalline thin films with the different dopant concentrations

The transparent nanocrystalline thin films of undoped zinc oxide and Mn-doped (Zn_1−xMn_xO) have been deposited on glass substrates via the sol–gel technique using zinc acetate dehydrate and manganese chloride as precursor. The as-deposited films with the different manganese compositions in the range of 2.5–20 at% were pre-heated at 100 °C for 1 h and 200 °C for 2 h, respectively, and then crystallized in air at 560 °C for 2 h. The structural properties and morphologies of the undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/Vis spectroscopy. The analyzed results indicates that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn related phases. Room temperature photoluminescence is observed for the ZnO and Mn-doped ZnO thin films.     

Morphology and optical properties of Mg and Sr doped CaF2 nanocrystals

Magnesium (Mg) and Strontium (Sr) doped Calcium fluoride nanocrystals were synthesized by co-precipitation method. The cubic structure of the samples was confirmed by Powder X-ray diffraction. The average crystallite size of Mg doped samples was found to be ~ 25 nm whereas in Sr doped one it was ~ 35 nm. The morphological features revealed that the nanocrystals were agglomerated, crispy and porous. The as-prepared samples showed the presence of hydroxyl groups. The optical absorption spectrum of as-prepared Mg doped samples showed a strong absorption band peaked at ~ 233 nm whereas the Sr doped one showed a prominent absorption peak at 248 nm. A strong PL emission was observed at ~ 300 nm in Mg doped samples. However, the Sr doped samples showed two prominent emissions at ~ 345 and 615 nm.     

Synthesis of nanocrystalline ZnO nanobelts via pyrolytic decomposition of zinc acetate nanobelts and their gas sensing behavior

The pyrolytic decomposition of layered basic zinc acetate (LBZA) nanobelts (NBs) into nanocrystalline ZnO NBs is investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). We also report on the gas sensing response of the resulting ZnO nanomaterial to CO. The LBZA NBs are grown at 65 °C in an aqueous solution of zinc acetate dihydrate. AFM and SEM results show as-grown products possess the characteristic layered structure of the LBZA crystals. XRD and XPS results show that annealing as-grown products at 210 °C in air causes a transformation from zinc acetate to nanocrystalline ZnO NBs via thermal decomposition. The ZnO crystalline domain size increases with temperature from 9.2 nm at 200 °C to 94 nm at 1000 °C, as measured from XRD. SEM shows evidence of sintering at 600 °C. The thickness of the NBs, determined via AFM, ranges from 10 to 50 nm and remains approximately constant with annealing temperature. XPS confirmed the chemical transformation from zinc acetate to ZnO and showed a significant remaining zinc hydroxide component for the ZnO NBs consistent with published results. PL measurements at room temperature show a blue shift in peak emission as the nanobelts change from LBZA to ZnO at 200 °C. Above this transition temperature, the ZnO nanobelts possess strong band edge emission at 390 nm and little broad band emission in the visible region. The AFM and SEM images reveal that the crystallites within the nanobelts orientate in rows along the long axis during annealing. This structure provides a high surface area to volume ratio of aligned nanoparticles which is beneficial for gas sensing applications. Gas sensors fabricated from 400 °C annealed nanobelts showed a response of 1.62 when exposed to 200 ppm of CO in dry air at 400 °C, as defined by the ratio of resistance before and during exposure. This indicates that ZnO nanostructures obtained by thermal decomposition of LBZA NBs could provide a cost effective route to high sensitivity gas sensors.     

Thermoluminescence,photoluminescence and EPR studies on Mn2+ activated yttrium aluminate (YAlO3) perovskite

Thermoluminescence (TL) measurements were carried out on undoped and Mn²⁺ doped (0.1 mol%) yttrium aluminate (YAlO₃) nanopowders using gamma irradiation in the dose range 1–5 kGy. These phosphors have been prepared at furnace temperatures as low as 400 °C by using the combustion route. Powder X-ray diffraction confirms the orthorhombic phase. SEM micrographs show that the powders are spherical in shape, porous with fused state and the size of the particles appeared to be in the range 50–150 nm. Electron Paramagnetic Resonance (EPR) studies reveal that Mn ions occupy the yttrium site and the valency of manganese remains as Mn²⁺. The photoluminescence spectrum shows a typical orange-to-red emission at 595 nm and suggests that Mn²⁺ ions are in strong crystalline environment. It is observed that TL intensity increases with gamma dose in both undoped and Mn doped samples. Four shouldered TL peaks at 126, 240, 288 and 350 °C along with relatively resolved glow peak at 180 °C were observed in undoped sample. However, the Mn doped samples show a shouldered peak at 115 °C along with two well defined peaks at ～215 and 275 °C. It is observed that TL glow peaks were shifted in Mn doped samples. The kinetic parameters namely activation energy (E), order of kinetics (b), frequency factor (s) of undoped, and Mn doped samples were determined at different gamma doses using the Chens glow peak shape method and the results are discussed in detail.     

Photocatalytic degradation of ciprofloxacin drug in water using ZnO nanoparticles

We report the synthesis of nanostructure ZnO semiconductor with ～2.1 nm diameter using a chemical precipitation method. The resulting nanoparticles were characterized by X-ray diffraction analysis (XRD), Fourier-transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The optical properties were investigated by UV–vis and fluorescence techniques. The absorption spectra exhibit a sharp absorption edge at ～334 nm corresponding to band gap of ～3.7 eV. The fluorescence spectra displayed a near-band-edge ultraviolet excitonic emission at ～410 nm and a green emission peak at ～525 nm, due to a transition of a photo-generated electron from the conduction band to a deeply trapped hole. The photocatalytic activity of the prepared ZnO nanoparticles has been investigated for the degradation of ciprofloxacin drug under UV light irradiation in aqueous solutions of different pH values. The results showed that the photocatalytic degradation process is effective at pH 7 and 10, but it is rather slow at pH 4. Higher degradation efficiency (～50%) of the drug was observed at pH 10 after 60 min. Photodegradation of the drug follows a pseudo-first-order kinetics.     

Two and four photon absorption and nonlinear refraction in undoped,chromium doped and copper doped ZnS quantum dots

The ZnS quantum dots (QDs) with Cr and Cu doping were synthesized by chemical co-precipitation method. The nanostructures of the prepared undoped and doped ZnS QDs were characterized by UV–vis spectroscopy, Transmission electron microscopy (TEM) and X-ray diffraction (XRD). The sizes of QDs were found to be within 3–5 nm range. The nonlinear parameters viz. Two photon absorption coefficient (β₂), nonlinear refractive index (n₂), third order nonlinear susceptibility (χ³) at wavelength 532 nm and Four photon absorption coefficient (β₄) at wavelength 1064 nm have been calculated by Z-scan technique using nanosecond Nd:YAG laser in undoped, Cr doped and Cu doped ZnS QDs. Higher values of nonlinear parameters for doped ZnS infer that they are potential material for the development of photonics devices and sensor protection applications.     

Synthesis and surface modification of ZnO:Cu nanoparticles by silica and PMMA

ZnO nanoparticles doped with Cu were synthesized by solid state reaction using different precursor routes and varying growth environment. Average crystallite size varied from 40 to 100 nm depending upon synthesis temperature, lower temperature favouring smaller particle size. Scanning electron microscope (SEM) images showed that particles synthesized at 250 °C were in the shape of nanorods but those synthesized at 900 °C had spherical shape. Luminescence emission showed marked dependence on the growth conditions varying from ultraviolet (UV) emission to green emission. For making the luminescent nanoparticles bio-compatible, a bioinorganic interface on ZnO:Cu nanoparticles was created by coating them with inert silica. Surface modification of ZnO:Cu was also done with lipophilic polymethylmethacrylate (PMMA). ZnO:Cu nanoparticles showed hexagonal wurtzite structure and the coating of silica was confirmed with the presence of two extra peaks due to silica in the XRD spectra. Thermogravimetric analysis (TGA) and FTIR spectroscopy indicated that PMMA molecules were adsorbed on the surface of ZnO:Cu nanoparticles. SEM images revealed that PMMA adsorption improved the dispersibilty of ZnO:Cu nanoparticles.     

A templateless surfactant-free seedless aqueous route to single-crystalline ZnO nanowires synthesis

Zinc oxide (ZnO) nanowires (NWs) have been synthesized using zinc nitrate and hexamethylenetetramine by templateless, surfactant-free and seedless aqueous solution route. The morphology of ZnO NWs was considerably affected by growth time: a longer reaction time results in the formation of ZnO NWs. Structural analysis of the synthesized NWs showed an average diameter of 20–30 nm length of several micrometers and single-crystalline wurtzite hexagonal structure. Photoluminescence studies of ZnO NWs showed a strong green emission peak at 585 nm.     

Defect induced paramagnetism in lightly doped ZnS:Fe nanoparticles

Nanoparticles of ZnS:Fe (0, 1, 3, and 5 at%) were synthesized by a refluxing route at 80 °C. All the samples exhibited cubic structure as revealed by X-ray powder diffraction studies. Blue emission of undoped samples was totally quenched by Fe doping. Magnetic measurements showed that the undoped ZnS was diamagnetic whereas all the doped samples were paramagnetic at room temperature. EPR signal characteristic of Fe³⁺ was observed in all the doped samples at room temperature. The paramagnetism of the present samples is attributed to the presence of uncoupled Fe³⁺ ions mediated by cation vacancies.     

Eu-doped ZnO nanoparticles: Sonochemical synthesis,characterization, and sonocatalytic application

Undoped and europium (III)-doped ZnO nanoparticles were prepared by a sonochemical method. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) analysis. The crystalline sizes of undoped and 3% Eu-doped ZnO were found to be 16.04 and 8.22 nm, respectively. The particle size of Eu-doped ZnO nanoparticles was much smaller than that of pure ZnO. The synthesized nanocatalysts were used for the sonocatalytic degradation of Acid Red 17. Among the Eu-doped ZnO catalysts, 3% Eu-doped ZnO nanoparticles showed the highest sonocatalytic activity. The effects of various parameters such as catalyst loading, initial dye concentration, pH, ultrasonic power, the effect of oxidizing agents, and the presence of anions were investigated. The produced intermediates of the sonocatalytic process were monitored by GC–Mass (GC–MS) spectrometry.     

High quality nitrogen-doped zinc oxide thin films grown on ITO by sol–gel method

Highly transparent N-doped ZnO thin films were deposited on ITO coated corning glass substrate by sol–gel method. Ammonium nitrate was used as a dopant source of N with varying the doping concentration 0, 0.5, 1.0, 2.0 and 3.0 at%. The DSC analysis of prepared NZO sols is observed a phase transition at 150 °C. X-ray diffraction pattern showed the preferred (002) peak of ZnO, which was deteriorated with increased N concentrations. The transmittance of NZO thin films was observed to be ~88%. The bandgap of NZO thin films increased from 3.28 to 3.70 eV with increased N concentration from 0 to 3 at%. The maximum carrier concentration 8.36×10¹⁷ cm⁻³ and minimum resistivity 1.64 Ω cm was observed for 3 at% N doped ZnO thin films deposited on glass substrate. These highly transparent ZnO thin films can be used as a window layer in solar cells and optoelectronic devices.     

High c-axis preferred orientation ZnO thin films prepared by oxidation of metallic zinc

Thin films of zinc oxide were grown on glass substrates by thermal oxidation. The metallic zinc films were thermally oxidized at different temperatures ranging from 300 to 600 °C to yield ZnO thin films. The structural property of the thin films was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The X-ray diffraction measurements showed that the films oxidized at 300 °C were not oxidized entirely, and the films deposited at 600 °C had better crystalline quality than the rest. When the oxidation temperature increased above 400 °C, the films exhibited preferred orientation along (002) and high transmittance ranging from 85% to 98% in vis–near-infrared band. Meanwhile, the films showed a UV emission at about 377 nm and green emission. With the increasing of oxidation temperature, the intensity of green emission peak was enhanced, and then decreased, disappearing at 600 °C, and the case of UV emission increased. Furthermore, a strong green emission was observed in the film sintered in pure oxygen atmosphere.     

Fabrication of Fe-doped TiO2 nanoparticles and investigation of photocatalytic decolorization of reactive red 198 under visible light irradiation

In this research, Fe-doped TiO₂ nanoparticles with various Fe concentrations (0. 0.1, 1, 5 and 10 wt%) were prepared by a sol–gel method. Then, nanoparticles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis (EDX), BET surface area, photoluminescence (PL) spectroscopy and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the nano-particles was evaluated through degradation of reactive red 198 (RR 198) under UV and visible light irradiations. XRD results revealed that all samples contained only anatase phase. DRS showed that the Fe doping in the titania induced a significant red shift of the absorption edge and then the band gap energy decreased from 3 to 2.1 eV. Photocatalytic results indicated that TiO₂ had a highest photocatalytic decolorization of the RR 198 under UV irradiation whereas photocatalytic decolorization of the RR 198 under visible irradiation increased in the presence of Fe-doped TiO₂ nanoparticles. Among the samples, Fe-1 wt% doped TiO₂ nanoparticles showed the highest photocatalytic decolorization of RR198 under visible light irradiation.     

The spectroscopic properties of Yb3+ doped α-BBO crystal

2.0 mol% (relative to Ba²⁺) Yb³⁺ doped α-BaB₂O₄ (α-BBO) crystal was obtained by the Czochralski method. The doped crystal structure was determined by means of an X-ray diffraction analysis. The absorption, near-infrared (NIR) luminescence spectra and fluorescence decay curve of Yb³⁺ doped α-BBO crystal were investigated. NIR emission under 940 nm and 980 nm LDs (laser diodes) excitation was observed in the Yb doped α-BBO crystal.     

Studies on structural and magnetic properties of Co-doped pyramidal ZnO nanorods synthesized by solution growth technique

Large-area arrays of highly oriented Co-doped ZnO nanorods with pyramidal hexagonal structure are grown on silica substrates by wet chemical decomposition of zinc–amino complex in an aqueous medium. In case of undoped ZnO with an equi-molar ratio of Zn²⁺/hexamethylenetetramine (HMT), highly crystalline nanorods were obtained, whereas for Co-doped ZnO, good quality nanorods were formed at a higher Zn²⁺/HMT molar ratio of 4:1. Scanning electron microscope (SEM) studies show the growth of hexagonal-shaped nanorods in a direction nearly perpendicular to the substrate surface with a tip size of ～50 nm and aspect ratio around 10. The XRD studies show the formation of hexagonal phase pure ZnO with c-axis preferred orientation. The doping of Co ions in ZnO nanorods was confirmed by observation of absorption bands at 658, 617 and 566 nm in the UV–vis spectra of the samples. The optical studies also suggest Co ions to be present both in +2 and +3 oxidation states. From the photoluminescence studies, a defect-related emission is observed in an undoped sample of ZnO at 567 nm. This emission is significantly quenched in Co-doped ZnO samples. Further, the Co-doped nanorods have been found to show ferromagnetic behavior at room temperature from vibrating sample magnetometer (VSM) studies.     

Sonocatalytic degradation of Acid Blue 92 using sonochemically prepared samarium doped zinc oxide nanostructures

Pure and Sm-doped ZnO nanoparticles were synthesized applying a simple sonochemical method. The nanocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) techniques which confirmed the successful synthesis of the doped sonocatalyst. The sonocatalytic degradation of Acid Blue 92 (AB92), a model azo dye, was more than that with sonolysis alone. The 6% Sm-doped ZnO nanoparticles had a band gap of 2.8 eV and demonstrated the highest activity. The degradation efficiency (DE%) of sonolysis and sonocatalysis with undoped ZnO and 6% Sm-doped ZnO was 45.73%, 63.9%, and 90.10%, after 150 min of treatment, respectively. Sonocatalytic degradation of AB92 is enhanced with increasing the dopant amount and catalyst dosage and with decreasing the initial AB29 concentration. DE% declines with the addition of radical scavengers such as chloride, carbonate, sulfate, and tert-butanol. However, the addition of enhancers including potassium periodates, peroxydisulfate, and hydrogen peroxide improves DE% by producing more free radicals. The results show adequate reusability of the doped sonocatalyst. Degradation intermediates were recognized by gas chromatography–mass spectrometry (GC–MS). Using nonlinear regression analysis, an empirical kinetic model was developed to estimate the pseudo-first-order constants (k_app) as a function of the main operational parameters, including the initial dye concentration, sonocatalyst dosage, and ultrasonic power.     

Influence of ultrasonication times on the tunable colour emission of ZnO nanophosphors for lighting applications

This paper reports on the sonochemical synthesis of zinc oxide (ZnO) nanophosphors (NPr) at different ultrasonication times (5 min, 30 min, 1 h, 5 h, 10 h and 15 h) for near white light emission applications. X-ray photoelectron spectroscopy indicated that the O1s peak consists of two components. These were O1 (ZnO) and O2 (deficient oxygen; OH groups) centred at 529.7 ± 0.3 eV and 531.1 ± 0.3 eV, respectively. All samples showed UV and defect level emission (DLE). The DLE enhancement was due to the increase in oxygen related defects such as oxygen vacancies/interstitials. Due to the combination of near UV and DLE near white light emission in ZnO NPr was obtained. The emission could be tuned with different ultrasonic times. It was found that the ultrasonication time influenced the growth mechanism and luminescence properties of the ZnO NPr.     

Excellent UV absorption in spin-coated thin films of oleic acid modified zinc oxide nanorods embedded in Polyvinyl alcohol

The aim of the study is to investigate the optical properties of spin-coated, highly transparent nanocomposite films of oleic acid modified ZnO (Zinc oxide) nanorods embedded in Polyvinyl alcohol (PVA) matrix. Pristine and oleic acid (OA) modified ZnO nanorods have been prepared by wet chemical synthesis and are characterized by X-ray diffraction, FESEM, TEM and FT–IR spectroscopy techniques. The optical properties of ZnO/PVA films are studied using UV–visible absorption and Photoluminescence (PL) spectroscopy. The results show that the optical absorption of the films in the UV region is quite high and more than 95% absorption is observed in films prepared from OA modified ZnO nanorods. The excellent UV absorption at around 300 nm offers prospects of applications of these films as efficient UV filters in this wavelength region. The PL spectrum of pristine ZnO nanorods shows almost white light emission whereas OA modified ZnO nanorods have a more intense peak centered in the blue region. The PL emission of OA modified ZnO/PVA film shows appreciable increase in intensity compared to the film obtained with pristine ZnO. The surface modification of ZnO by the polymer matrix removes defect states within ZnO and facilitates sharp near band edge PL emission at 364 nm.     

Luminescence characteristics of cobalt doped TiO2 nanoparticles

TiO₂ nanoparticles doped with two different concentrations of Cobalt, 0.02 and 0.04 mol, are prepared by sol–gel method. The crystalline phase of the doped and undoped nanoparticles and particle sizes are observed with X-ray diffraction and transmission electron microscope. FTIR confirms the bonding interaction of Co²⁺ in TiO₂ lattice framework. The UV absorption spectra of the doped material shows two absorption peaks in the visible region related to d–d electronic transitions of Co²⁺ in TiO₂ lattice. Compared to undoped TiO₂ nanoparticles, the cobalt doped samples show a red shift in the band gap. Steady state photoluminescence spectra give emission peaks related to oxygen defects. The decrease in the intensity ratio of UV/visible emission peaks confirms distortion of structural regularity and formation of defects after doping. The intensity ratio of different visible emission peaks is nearly same for undoped and 0.02 Co²⁺. However, this ratio decreases profoundly at 0.04 Co²⁺, due to concentration quenching effect. Photoluminescence excitation spectra, recorded at 598 nm emission wavelength, give different excitation peaks associated with oxygen vacancies and Co²⁺. Time resolved photoluminescence spectra give longer decay time for doped samples, indicating longer relaxation of conduction band electrons on the defect and on dopant sites.     

Green synthesis of silver-graphene nanocomposite-based transparent conducting film

In the present work, silver nanoparticles (Ag NPs)/graphene nanocomposite has been synthesized successfully by simple solvothermal method via green route. Citric acid is used as green reducing agent for the reduction of graphene oxide (GO) and Ag ions. Silver nitrate is used as a precursor material for Ag NPs. As synthesized Ag NPs/graphene nanocomposite has been characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infra-red spectroscopy, UV–vis spectroscopy, thermal gravimetric analysis, field emission scanning electron microscopy, and X-ray photoelectron spectroscopy. Experimental results confirm the reduction of GO and the successful formation of Ag NPs decorated graphene nanosheets. In addition, spray coating technique is employed for the fabrication of transparent conducting films. Enhancement in the optoelectrical signatures has been achieved using thermal graphitization of fabricated films. Thermal graphitization at 800 °C for 1 h marks the best performance of fabricated film with sheet resistance of ~3.4 kΩ/□ and transmittance (550 nm) of ~66.40%, respectively.