A chemical precursor for depositing Sb(2)S(3) onto mesoporous TiO(2) layers in nonaqueous media and its application to solar cells

Deposition of nanocrystalline Sb(2)S(3) onto a mesoporous TiO(2) photoanode is an important process in the fabrication of Sb(2)S(3)-sensitized solar cells. In order to generate oxide-free nanosized Sb(2)S(3), a single-source precursor for the chemical bath deposition of Sb(2)S(3) in nonaqueous media, Sb(iii)(thioacetamide)(2)Cl(3), was synthesized and used to produce high-quality Sb(2)S(3) for solar cells.     

掺钠钼电极在硒化铜铟镓(CIGS)太阳能薄膜电池应用

适量钠元素对铜铟镓硒薄膜生长具有促进作用,本文主要研究了掺钠钼电极特性及其对铜铟镓硒薄膜太阳能电池性能的影响。利用磁控溅射方法制备不同厚度的钼钠/钼(Mo Na/Mo)薄膜作为背电极,并在(Mo Na/Mo)薄膜电极上蒸镀铜铟镓硒(CIGS)薄膜,并利用单质硒源硒化处理后制备CIGS薄膜电池。SEM和XRD结果表明采用三层叠层Mo/Mo/Mo Na薄膜做电极的Mo Na容易被氧化,电阻率增加,采用四层叠层Mo/Mo/Mo Na/Mo薄膜电极方式有效降低电阻率,阻止Mo Na被氧化,CIGS晶粒较大且致密。在同一条件下,在不同Mo Na/Mo厚度电极上制备CIGS薄膜电池,80 nm Mo Na厚度上的CIGS薄膜电池效率达6.54%。     

The origin of open circuit voltage of porphyrin-sensitised TiO(2) solar cells

Electron lifetime and diffusion coefficient measurements in highly efficient porphyrin-sensitised TiO(2) solar cells showed reduced electron lifetime, and consequently, lower photo-induced electron density under illumination compared to commonly used ruthenium dye (N719)-sensitised solar cells, which is proposed to be the origin of the generally lower open circuit voltage.     

Unsymmetric Platinum(II) Bis(aryleneethynylene) Complexes as Photosensitizers for Dye‐Sensitized Solar Cells

Four new unsymmetric platinum(II) bis(aryleneethynylene) derivatives have been designed and synthesized, which showed good light‐harvesting capabilities for application as photosensitizers in dye‐sensitized solar cells (DSSCs). The absorption, electrochemical, time‐dependent density functional theory (TD‐DFT), impedance spectroscopic, and photovoltaic properties of these platinum(II)‐based sensitizers have been fully characterized. The optical and TD‐DFT studies show that the incorporation of a strongly electron‐donating group significantly enhances the absorption abilities of the complexes. The maximum absorption wavelength of these four organometallic dyes can be tuned by various structural modifications of the triphenylamine and/or thiophene electron donor, improving the light absorption range up to 650 nm. The photovoltaic performance of these dyes as photosensitizers in mesoporous TiO₂ solar cells was investigated, and a power conversion efficiency as high as 1.57 % was achieved, with an open‐circuit voltage of 0.59 V, short‐circuit current density of 3.63 mA cm^?2, and fill factor of 0.73 under simulated AM 1.5G solar illumination.     

The mechanism of photo- and thermooxidation of poly(3-hexylthiophene) (P3HT) reconsidered

Poly(3-hexylthiophene) (P3HT) has been the focus of great interest as it is widely used in organic solar cells. However, P3HT has relatively poor photochemical and thermal stability under ambient atmosphere, which leads to a reduced lifetime of the solar cells. It was therefore necessary to study the photo- and thermooxidation of P3HT. Thin P3HT films were exposed to UV-visible light irradiation and thermal ageing, both in the presence of air. Changes in the infrared spectra of the aged samples were recorded, and the oxidation products were identified. A degradation mechanism that accounted for the modifications in the infrared spectra was then developed. This mechanism confirmed that singlet oxygen plays no decisive role, as previously reported. Oxidation was shown to involve the radical oxidation of the n-hexyl side-chains and the subsequent degradation of the thiophene rings. The breaking of the macromolecular backbone resulted in a loss of π-conjugation, provoking the bleaching of the sample.     

Applications of laser-induced breakdown spectrometry (LIBS) in surface analysis

The applicability of laser-induced breakdown spectrometry (LIBS) for surface analysis is presented in terms of its lateral and depth resolution. A pulsed N(2) laser at 337.1 nm (3.65 J/cm(2)) was used to irradiate solar cells employed for photovoltaic energy production. Laser produced plasmas were collected and detected using a charge-coupled device. An experimental device developed in the laboratory permits an exact synchronization of sample positioning using an XY motorized system with laser pulses. Multielement analysis with lateral resolution of up to 30 microm is feasible with the present system. Three-dimensional capabilities of the system are used for studies on the distribution of carbon impurities at the surface of the solar cells.     

SnO(2) nanowall-arrays coated with rutile-TiO(2) nanoneedles for high performance dye-sensitized solar cells

A novel architecture of SnO(2) nanowall-arrays coated with rutile-TiO(2) nanoneedles is fabricated for the first time and envisaged in dye-sensitized solar cells. Devices constructed using these architectures showed a power conversion efficiency of 4.12%, which is the highest among the SnO(2) nanostructures grown on conducting substrates by wet chemical methods.     

Emerging Earth-abundant (Fe,Co, Ni,Cu) molecular complexes for solar fuel catalysis

Current micro review focuses on Earth-abundant molecular transition metal photosensitizers and catalysts for dye sensitized photoelectrochemical cells for direct solar energy storage. The possibility of direct conversion of solar energy into fluids (ethanol or methanol) or gases (hydrogen or methane) in a cost efficient way is considered a disruptive and innovative breakthrough for large-scale implementation of solar fuel technologies. At present, it is a fast-growing research area and the most outstanding results are highlighted.     

Highly efficient solar cells based on poly(3-butylthiophene) nanowires

Poly(3-butylthiophene) (P3BT) nanowires, prepared by solution-phase self-assembly, have been used to construct highly efficient P3BT/fullerene nanocomposite solar cells. The fullerene/P3BT nanocomposite films showed an electrically bicontinuous nanoscale morphology with average field-effect hole mobilities as high as 8.0 x 10(-3) cm2/Vs due to the interconnected P3BT nanowire network revealed by TEM and AFM imaging. The power conversion efficiency of fullerene/P3BT nanowire devices was 3.0% (at 100 mW/cm2, AM1.5) in air and found to be identical with our similarly tested fullerene/poly(3-hexylthiophene) photovoltaic cells. This discovery expands the scope of promising materials and architectures for efficient bulk heterojunction solar cells.     

聚(3,4-二氧乙基噻吩)在有机光电子领域的应用进展

简要综述了高性能导电高分子聚(3, 4 二氧乙基噻吩)在有机光电子领域,特别是在有机电致发光和有机太阳能电池中的应用.     

The influence of poly(3-hexylthiophene) regioregularity on fullerene-composite solar cell performance

A comparison of three samples of poly(3-hexylthiophene) having regioregularities of 86, 90, and 96% is used to elucidate the effect of regioregularity on polymer-fullerene-composite solar cell performance. It is observed that polymer samples with lower regioregularity are capable of generating fullerene composites that exhibit superior thermal stability. The enhanced thermal stability of the composites is attributed to a lower driving force for polymer crystallization in the less regioregular polymer samples, which is supported with two-dimensional grazing incidence X-ray scattering and differential scanning calorimetry measurements. Furthermore, it is demonstrated that all three polymer samples are capable of generating solar cells with equivalent peak efficiencies of approximately 4% in blends with [6,6]-phenyl-C61-butyric acid methyl ester. While it may be non-intuitive that polymers with lower regioregularity can exhibit higher efficiencies, it is observed that the charge-carrier mobility of the three polymers is on the same order of magnitude (10(-4) cm2 V(-1) s(-1)) when measured from the space-charge-limited current, suggesting that highly regioregular and crystalline polythiophenes are not required in order to effectively transport charges in polymer solar cells. Overall, these results suggest a design principle for semicrystalline conjugated polymers in fullerene-composite solar cells in which crystallization-driven phase separation can be dramatically suppressed via the introduction of a controlled amount of disorder into the polymer backbone.     

Efficient co-sensitization of nanocrystalline TiO(2) films by organic sensitizers

Dye-sensitized solar cells based on co-sensitization of organic dyes having complementary spectral absorption in the visible region resulted in a panchromatic response, which exhibited 86% incident monochromatic photon-to-current conversion efficiency in the visible region; the optimized cell gave a short circuit current density of 15.5 mA cm(-2), an open circuit voltage of 685 mV and a fill factor of 0.70 corresponding to an overall conversion efficiency of 7.43% under solar simulated light irradiation of 100 mW cm(-2).     

Multifunctional Conjugated Polymers with Main‐Chain Donors and Side‐Chain Acceptors for Dye Sensitized Solar Cells (DSSCs) and Organic Photovoltaic Cells (OPVs)

A novel multifunctional conjugated polymer (RCP‐1) composed of an electron‐donating backbone (carbazole) and an electron‐accepting side chain (cyanoacetic acid) connected through conjugated vinylene and terthiophene has been synthesized and tested as a photosensitizer in two major molecule‐based solar cells, namely dye sensitized solar cells (DSSCs) and organic photovoltaic cells (OPVs). Promising initial results on overall power conversion efficiencies of 4.11% and 1.04% are obtained from the basic structure of DSSCs and OPVs based on RCP‐1, respectively. The well‐defined donor (D)‐acceptor (A) structure of RCP‐1 has made it possible, for the first time, to reach over 4% of power conversion efficiency in DSSCs with an organic polymer sensitizer and good operation stability.     

Utilizing 3,4-ethylenedioxythiophene(EDOT)-bridged non-fullerene acceptors for efficient organic solar cells

A rational design of efficient low-band-gap non-fullerene acceptors(NFAs)for high-performance organic solar cells(OSCs)remains challenging;the main constraint being the decrease in the energy level of the lowest unoccupied molecular orbitals(LUMOs)as the bandgap of A-D-A-type NFAs decrease.Therefore,the short current density(J_sc)and open-circuit voltage(V_oc)result in a trade-off relationship,making it difficult to obtain efficient OSCs.Herein,three NFAs(IFL-ED-4 F,IDT-ED-4 F,and IDTT-ED-2 F)were synthesized to address the above-mentioned issue by introducing 3,4-ethylenedioxythiophene(EDOT)as aπ-bridge.These NFAs exhibit relatively low bandgaps(1.67,1.42,and 1.49 eV,respectively)and upshifted LUMO levels(-3.88,-3.84,and-3.81 eV,respectively)compared with most reported low-band-gap NFAs.Consequently,the photovoltaic devices based on IDT-ED-4 F blended with a PBDB-T donor polymer showed the best power conversion efficiency(PCE)of 10.4%with a high J_sc of 22.1 mA cm^-2 and Voc of 0.884 V among the examined NFAs.In contrast,IDTT-ED-4 F,which was designed with an asymmetric structure of the D-p-A type,showed the lowest efficiency of 1.5%owing to the poor morphology and charge transport properties of the binary blend.However,when this was introduced as the third component of the PM6:BTP-BO-4 Cl,complementary absorption and cascade energy-level alignment between the two substances could be achieved.Surprisingly,the IDTT-ED-4 F-based ternary blend device not only improved the Jscand Voc,but also achieved a PCE of 15.2%,which is approximately 5.3%higher than that of the reference device with a minimized energy loss of 0.488 eV.In addition,the universality of IDTT-ED-2 F as a third component was effectively demonstrated in other photoactive systems,specifically,PM6:BTPe C9 and PTB7-Th:IEICO-4 F.This work facilitates a better understanding of the structure–property relationship for utilizing efficient EDOT-bridged NFAs in high-performance OSC applications.     

掺钠钼电极在硒化铜铟镓（CIGS）太阳能薄膜电池应用

适量钠元素对铜铟镓硒薄膜生长具有促进作用,本文主要研究了掺钠钼电极特性及其对铜铟镓硒薄膜太阳能电池性能的影响。利用磁控溅射方法制备不同厚度的钼钠/钼（MoNa/Mo）薄膜作为背电极,并在（MoNa/Mo）薄膜电极上蒸镀铜铟镓硒（CIGS）薄膜,并利用单质硒源硒化处理后制备CIGS薄膜电池。SEM和XRD结果表明采用三层叠层Mo/Mo/MoNa薄膜做电极的MoNa容易被氧化,电阻率增加,采用四层叠层Mo/Mo/MoNa/Mo薄膜电极方式有效降低电阻率,阻止MoNa被氧化,CIGS晶粒较大且致密。在同一条件下,在不同MoNa/Mo厚度电极上制备CIGS薄膜电池,80nmMoNa厚度上的CIGS薄膜电池效率达6.54%。     

Thermodynamics of the equilibrium of the reaction between (5,10,15,20-tetra(2-methoxyphenyl)porphinato)chloroindium(III) and pyridine

The results from thermodynamic and quantum-chemical studies of the reversible reaction between (5,10,15,20-tetra(2-methoxyphenyl)porphinato)chloroindium(III) and pyridine are reported. The main physicochemical parameters of properties of its supramolecular products are obtained and analyzed. The addition of pyridine molecules to metalloporphyrin proceeds in one step to attain an equilibrium state with the formation of supramolecules with a stoichiometry of 2: 1; spectral characteristics and parameters of the stability of the latter are identified. The possibility of using substituted indium(III)porphyrin for further research in the field of hybrid solar cells is discussed.     

Applications of laser-induced breakdown spectrometry (LIBS) in surface analysis

The applicability of laser-induced breakdown spectrometry (LIBS) for surface analysis is presented in terms of its lateral and depth resolution. A pulsed N₂ laser at 337.1 nm (3.65 J/cm²) was used to irradiate solar cells employed for photovoltaic energy production. Laser produced plasmas were collected and detected using a charge-coupled device. An experimental device developed in the laboratory permits an exact synchronization of sample positioning using an XY motorized system with laser pulses. Multielement analysis with lateral resolution of up to 30 m is feasible with the present system. Three-dimensional capabilities of the system are used for studies on the distribution of carbon impurities at the surface of the solar cells.     

Soft X-ray characterization of Zn(1-x)Sn(x)O(y) electronic structure for thin film photovoltaics

Zinc tin oxide (Zn(1-x)Sn(x)O(y)) has been proposed as an alternative buffer layer material to the toxic, and light narrow-bandgap CdS layer in CuIn(1-x),Ga(x)Se(2) thin film solar cell modules. In this present study, synchrotron-based soft X-ray absorption and emission spectroscopies have been employed to probe the densities of states of intrinsic ZnO, Zn(1-x)Sn(x)O(y) and SnO(x) thin films grown by atomic layer deposition. A distinct variation in the bandgap is observed with increasing Sn concentration, which has been confirmed independently by combined ellipsometry-reflectometry measurements. These data correlate directly to the open circuit potentials of corresponding solar cells, indicating that the buffer layer composition is associated with a modification of the band discontinuity at the CIGS interface. Resonantly excited emission spectra, which express the admixture of unoccupied O 2p with Zn 3d, 4s, and 4p states, reveal a strong suppression in the hybridization between the O 2p conduction band and the Zn 3d valence band with increasing Sn concentration.     

Modified phthalocyanines for efficient near-IR sensitization of nanostructured TiO(2) electrode

A zinc phthalocyanine with tyrosine substituents (ZnPcTyr), modified for efficient far-red/near-IR performance in dye-sensitized nanostructured TiO(2) solar cells, and its reference, glycine-substituted zinc phthalocyanine (ZnPcGly), were synthesized and characterized. The compounds were studied spectroscopically, electrochemically, and photoelectrochemically. Incorporating tyrosine groups into phthalocyanine makes the dye ethanol-soluble and reduces surface aggregation as a result of steric effects. The performance of a solar cell based on ZnPcTyr is much better than that based on ZnPcGly. Addition of 3alpha,7alpha-dihydroxy-5beta-cholic acid (cheno) and 4-tert-butylpyridine (TBP) to the dye solution when preparing a dye-sensitized TiO(2) electrode diminishes significantly the surface aggregation and, therefore, improves the performance of solar cells based on these phthalocyanines. The highest monochromatic incident photo-to-current conversion efficiency (IPCE) of approximately 24% at 690 nm and an overall conversion efficiency (eta) of 0.54% were achieved for a cell based on a ZnPcTyr-sensitized TiO(2) electrode. Addition of TBP in the electrolyte decreases the IPCE and eta considerably, although it increases the open-circuit photovoltage. Time-resolved transient absorption measurements of interfacial electron-transfer kinetics in a ZnPcTyr-sensitized nanostructured TiO(2) thin film show that electron injection from the excited state of the dye into the conduction band of TiO(2) is completed in approximately 500 fs and that more than half of the injected electrons recombines with the oxidized dye molecules in approximately 300 ps. In addition to surface aggregation, the very fast electron recombination is most likely responsible for the low performance of the solar cell based on ZnPcTyr.     

Bandgap engineering of monodispersed Cu(2-x)S(y)Se(1-y) nanocrystals through chalcogen ratio and crystal structure

Bandgap engineering is important in light-absorption optimization of nanocrystals (NCs) for applications such as highly efficient solar cells. Herein, a facile one-pot method is developed to synthesize monodispersed ternary alloyed copper sulfide selenide (Cu(2-x)S(y)Se(1-y)) NCs with tunable composition, structure, and morphology. The energy bandgaps can be tuned with the chalcogen ratio, and the crystal structure of the NCs is found to produce an effect on their bandgap and light absorption. The results are significant in bandgap engineering of semiconductor NCs.