Grafting of Polymers from Carbon Fiber. Anionic Graft Polymerization of Vinyl Monomers Initiated by Metallized Aromatic Rings on Carbon Fiber

The anionic graft polymerization of vinyl monomers onto carbon fiber initiated by metallized carbon fiber was investigated. The metalation of polycondensed aromatic rings of the carbon fiber surface was achieved by the treatment of carbon fiber with n-butyl-lithium (BuLi) in N, N, N′, N′ -tetramethylethylenediamine (TMEDA) or hexamethylphosphorous triamide (HMPT) at 0°C. The anionic polymerization of methyl methacrylate (MMA) and styrene (St) was initiated by the metallized carbon fiber, and these polymers were grafted onto the surface. The conversion and the percentage of grafting increased with increasing amount of BuLi used for the metalation of carbon fiber. When 0.20 g carbon fiber was treated with 0.3 mmol BuLi in TMEDA, the percentage of grafting of PMMA and PSt reached a maximum value (PMMA, 34.5%; PSt, 37.1 %). Furthermore, the metalation of aromatic rings of carbon fiber also proceeds by the treatment with BuLi in HMPT. On the contrary, no grafting was observed when carbon fiber was treated with BuLi in tetrahydrofuran (THF) or toluene. This may be due to the fact that metalation of carbon fiber does not proceed in THF or toluene.     

Grafting of polymers onto carbon whisker by anionic graft polymerization of vinyl monomers using metallized aromatic rings and/or phenoxy lithium groups on the surface as initiator

During the anionic polymerization of methyl methacrylate (MMA) initiated by n-butyl-lithium (n-BuLi) in the presence of carbon whisker, PMMA was found to be grafted onto the surface depending on the propagation from OLi groups, which are produced by the reaction of oxygen containing groups on the surface with n-BuLi. But no grafting of polystyrene was observed at all. By the activation of OLi groups by the addition of crown ether, however, the grafting of polystyrene onto the carbon whisker was achieved. On the other hand, it was found that metallized carbon whisker also initiates the anionic graft polymerization of MMA and styrene: percentage of grafting of PMMA and polystyrene reached 231.3 and 157.9%, respectively. The metalation of carbon whisker was achieved by the treatment with n-BuLi in aprotic polar solvents, such as N,N,N′,N′-tetramethylethylene-diamine or hexamethylphosphorous triamide, and in toluene in the presence of complexing agent of cation such as crown ether or a small amount of aprotic solvent. In the polymerization, grafted polymer chains were considered to propagate both from metallized aromatic rings and from OLi groups. The polymer-grafted carbon whisker gave a stable colloidal dispersion in organic solvents.     

Phase diagram of the system dihexadecylphosphatidylcholine/dihexadecyl-phosphatidic acid/water/NaOH at pH=14

Differential-scanning-calorimetry, freeze-fracture electron microscopy, and³¹P-NMR spectroscopy were used to study the lyotropic and thermotropic properties of the system dihexadecylphosphatidylcholine/dihexadecylphosphatidic acid/water/ NaOH in dispersion with excess water at pH=14. The phase diagram showed that both phospholipids are demixed nearly completely in the gel phase. The coexistence of theP and theB -phase in the mixtures was pointed out in the freeze-fracture electron micrographs by the ripple structure (P -phase) and by the lamellar structure (B -phase).     

Kinetic study of the metalation of a polystyrene model compound by the secondary butyllithium-N,N,N′,N′-tetramethylethylene diamine complex

2.5-Diphenyl hexane, a model compound of polystyrene was metalated by a complex of secondary butyllithium and N,N,N′,N′-tetramethylethylene diamine in heptane. At various times, the lithiated dimer was quenched with deuterated methanol. The deuterated compound was examined by mass spectrometry and from the deuterium content, the degree of lithiation was determined. The effects of the concentration of styrene units, secondary butyllithium and diamine on the lithiation were studied at 20 C and ?20 C. The overall rate of metalation was first order with respect to the styrene units concentration and half-order with respect to sec. butylithium-TMEDA complex concentration. The kinetic results were explained by the presence at 20 C of the 1 4 complex (1 sec. BuLi 4 TMEDA) and at ?20 C of the 1–2 complex (1 sec. BuLi 2 TMEDA).     

Study of the polymer latex coalescence by dielectric measurements at microwave frequency—feasibility of the method

The measurement of the complex dielectric constant ( ^*=–j) in the dipolar absorption domain of the free water molecule (microwave region) permits us to follow quasi-specifically and precisely the water circulation during the coalescence process of a latex. Weight losses and dielectric constants variations have been simultaneously recorded upon latex drying, in a resonant cavity at 5 and 9 GHz and under controlled atmosphere and temperature. Two different latexes were studied (polybutylacrylate (PBuA) and polystyrene (PS)) from which the glass transition temperature effect was investigated. It is found that the harder the polymer particles, the more clearly evidenced the flocculation and packing points are. This method appears to be quite reliable for discriminating the various steps in the film formation process of latexes.     

Deposition of polymer latices on grafted Nylon 6 fiber

Deposition of polymer latices on a grafted Nylon 6 fiber was studied as a function of pH and the degree of grafting. The latices were polystyrene (PS), styrene/acrylamide copolymer (P(St/AAm)) and styrene/acrylic acid copolymer (P(St/AA)). The deposition of the latices on the grafted fiber decreased in every case with increasing pH and no deposition was observed at alkaline pH. The grafting of fiber with acrylic and methacrylic acid reduced the deposition of P(St/AAm) and P(St/AA) latices but had no influence on the deposition of PS latex. The relation between the deposition rates and the interaction energy at acidic pH indicates that the deposition of PS latex on the grafted fiber mainly depends on the electrostatic interaction. These results suggest that the expansion of water-soluble polyelectrolyte layer on the surface of grafted fiber plays an important role on the deposition.     

Preparation of micron-size monodisperse polymer microspheres having cationic groups

Micron-size monodisperse crosslinked polymer microspheres having chloromethyl groups were prepared by seeded copolymerization of styrene, divinylbenzene, and chloromethylstyrene in the presence of 2.1- monodisperse polystyrene seed particles produced by dispersion polymerization. The modification reaction of chloromethyl groups on the surfaces with polyamines such as triethylenetetramine and ethylenediamine was carried out. From the measurements of potential and the amount of chloride ion released, the introduction of a large number of cationic groups at the surfaces was confirmed.Part CXXXI of the series Studies on suspension and Emulsion.     

Surfactant-free emulsion polymerization of styrene using crosslinked seed particles

The aim of this research was to prepare a monodisperse polystyrene latex without surfactants adsorbed at the particle surface. Conventional polymerization formulations usually lead to large amounts of oligomers. Furthermore, they are characterized by a low reproducibility with respect to particle size. This was overcome by using a seed latex that was crosslinked in order to overcome dissolution in the monomer phase. By adjusting the seed concentration, any desired particle size in the range 0.5–1.2 m could be obtained. The monodispersity was very good.     

Swelling of sodium acrylate gels

The swelling process of sodium acrylate gel is experimentally investigated. It is found that sodium acrylate gels weakly crosslinked with N,N-methylene-bis-acrylamide may undergo volume phase transition and that different kinds of mechanical instabilities occur in sequence at the transition. Peculiar wrinkle patterns appear on the free surface of an unstable gel and are changed in geometry as swelling proceeds. Cellular patterns seen at various instances in the late period of swelling are ascertained to be geometrically similar to each other and different only in size. The radii of spherical acrylate gels allowed to swell in water are measured as functions of time. The results are discussed and compared with the kinetic theories of swelling. As a result, these theories are proved to be unsatisfactory to fully describe the experimental facts.     

XPS analysis (ESCA) of the surface composition of poly(styrene/2-hydroxyethyl methacrylate) microspheres produced by emulsifier-free emulsion polymerization

Polymer microspheres composed of various compositions of styrene and 2-hydroxyethyl methacrylate (HEMA) were produced by batch emulsifier-free emulsion polymerization. The HEMA content at the surface, [HEMA] _s , of the microspheres powdered by freeze-drying was determined by both quantitativeC ^1s /O ^1s analysis andC ^1s peak shape analysis of the x-ray photoelectron spectroscopic spectra. When the HEMA content in the microsphere, [HEMA] _p , was less than about 5 mole%, the [HEMA] _s values determined by the two different methods showed good agreement. At [HEMA]_p above 5 mole %, [HEMA]_s values determined by the first method were about 15 mole % greater than those determined by the second. They both showed a similar tendency with the [HEMA] _s being higher than the [HEMA] _p , e.g., when [HEMA] _p was 1 mole %, [HEMA] _s was 11 mole %. The intensity of the satellite peak due to the ^* transition of the benzene ring of the styrene component decreased with an increase in [HEMA] _p , to zero at 5 mole % of [HEMA] _p . These results indicate that the HEMA component is localized at the surface.Part CVIII of the series Studies on Suspension and Emulsion.     

Immunoactivity of polymer microspheres with their hydrophilic/hydrophobic heterogeneous surface sensitized with an antibody

Styrene/2-hydroxyethyl methacrylate polymer microspheres consisting of various polymer compositions were produced by emulsifier-free seeded emulsion polymerization technique. Using these microspheres, which should have hydrophilic/hydrophobic heterogeneous surface, the effects of surface hydrophilicity on the main, fundamental requirements for an immunomicrosphere — high colloidal stability, sensitive immunologic agglutinability and insensitive non-specific agglutinability — were studied in detail. There was a region of the surface hydrophilicity that satisfied the three requirements simultaneously.Part CII of the series Studies on Suspension and Emulsion.     

Synthesis of poly(methyl methacrylate) macromonomer

Anionic polymerization of methyl methacrylate (MMA) was carried out in tetrahydrofuran (THF) or THF/toluene mixture at ?78°C initiated by triphenylmethyl sodium or lithium as initiators. Highly syndiotactic PMMA of low polydispersity (M _w/m _n = 1.11–1.17) could be prepared with triphenylmethyl lithium in THF or THF/toluene mixture at ? 78°C. Moreover, PMMA macromonomer having one vinylbenzyl group per polymer chain was prepared by the couplings of living PMMA initiated by triphenylmethyl lithium with p-chloromethyl styrene (CMS) at ?78°C. The coupling reaction of living PMMA initiated by triphenylmethyl sodium with CMS was scarcely occurred.     

Small-angle neutron scattering of colloidal silica dispersions in a non-polar solvent

Small-angle neutron scattering studies were performed on dilute dispersions of colloidal silica spheres in mixtures of h₁₂- and d₁₂-cyclohexane. The particles consisted of a SiO₂-core and a layer of stearyl alcohol molecules terminally attached with a chemical bond (Si-O) to the particle surface. The contrast variation method was applied to reveal the internal structure of the particles. The matchpoints determined with this method were in accordance with those calculated from the mass density of the particles and the atomic composition, as determined with elemental analysis.For a detailed interpretation of the scattering curves, we assumed that the particles were spherosymmetrical and consisted of two concentric layers. With the relation we derived between the radius of gyration and the reciprocal contrast for such a model, it was possible to determine all the parameters characterizing the particle in terms of this model. The model calculations performed using these parameters fitted very well to the experimental intensities for high contrasts. For lower contrasts, the fit was somewhat less good. This is probably due to random fluctuations in the scattering length density within the particle core.The different radii as found by neutron scattering, agreed very well with those determined using other techniques, such as light scattering (static and dynamic) and electron microscopy.     

Eigenvectors of the polyethylene chain with conformational defects calculated semianalytically by Green's function

Eigenvectors of vibrating polyethylene chains with (200) and (110) folds have been calculated by solving the phonon-scattering problem exactly with the method of Green's function. The results are applied to analyze the resonance modes of the (200) fold (ggtgg: 1353, 1356, 1374 cm^–1) and the (110) fold (approximately ggggtg: 820, 1288, 1342, 1348, 1372, 1374 cm^–1) in terms of the characteristic vibrations of smaller subunits of the (200) fold (gg, gtg) and the (110) fold (ggggtg, gggg, gtg) which can be identified spectroscopcally.Dedicated to Prof. Dr. W. Pechhold on the occasion of his 60th birthday     

Polyacrylamide Na-kaolinite interactions: Effect of electrolyte concentration on polymer adsorption

The variation in polyacrylamide adsorption on Na-kaolinite as a function of the electrolyte concentration of the clay suspension, was determined under three pH conditions, where the clays display varying charge characteristics. Interpretation of the results is based on two arguments: non-charged polyacrylamide adsorption is restricted to the edge faces of the colloidal platelets and hydrogen bonding between the amide groups of the polymer and the isolated hydroxyl sites of these faces is the mode of surface attachment. At constant pH, when Na-kaolinite bears charged surface groups, the polymer adsorption, which is related to the density of the anchoring sites, parallels the state of ionization of the edge surface. The mechanism by which the salt modifies the adsorption properties of the kaolinite in neutral medium is not established with certainty. Nevertheless, no polymer-clay association occurs if the surface is entirely uncharged. This result is in line with the fact that while hydroxyl groups are engaged in internal hydrogen bonds, they cannot hydrogen-bond to the polyacrylamide. Variations in the clay-polymer affinity are attributed to a modification of the interfacial structure of the adsorbed polymer, associated with changes in the surface density of the anchoring groups.     

Comment on the “dielectric properties of LDPE/Ny6 blends”

Data published by La Mantia et al. [1] on dielectric dispersion and loss in polyethylene/nylon 6 blends are analyzed in terms of dielectric mixture formulae. It is shown that an ohmic interfacial polarization process can not be responsible for the unexpected increase of and values observed in these blends at high temperatures. The observed phenomena are tentatively attributed to space charge processes at the electrodes or to other defects dipole mechanisms.     

Amphoteric character of polyelectrolyte complex particles as revealed by isotachophoresis and viscometry

Isotachophoresis and viscometric measurements were performed on aqueous dispersions of non-stoichiometric polyelectrolyte complexes in order to elucidate the surface charge situation of the complex particles in dependence on component charge density, ratio of cationic to anionic groups in the complex, and pH and ionic strengths of the ambient medium. Components for complex formation were acryl-based anionic and cationic polyelectrolytes of the pendent type. From our results, an amphoteric character of the polyelectrolyte complex particles can be concluded, with an isoelectric point characterized by zero mobility and a minimum in reduced viscosity _spec/c of the particle dispersion, and with the sign of net surface charge depending on ambient pH and component charge density. The influence of ionic strength on the _spec/c vs pH plots can be interpreted by assuming a competition between salting-out and electrostatic shielding effects. No correlation could be established between the overall molar ratio of cationic to anionic groups and the isoelectric point of the complex particles, which obviously indicates a different composition of surface and bulk of the polyelectrolyte complex particles.     

Grafting onto ultrafine ferrite particles: Reaction of isocyanate-capped polypropylene glycol with hydroxyl groups on the surface

The grafting of polypropylene glycol (PPG) onto an ultrafine ferrite by the reaction of hydroxyl groups on the surface with isocyanate-capped PPG (PPG-NCO), prepared by the reaction of an equimolecular amount of PPG with tolylene 2,4-diisocyanate, was investigated. When PPG-NCO (M _n=2.5×10³) was heated with the ferrite in bulk, the percentage of grafting onto the ferrite at 120 °C was increased up to 18.5%. On the contrary, the grafting by the reaction of PPG with hydroxyl groups on the ferrite at 120°C was scarcely observed. The grafted PPG onto the ferrite was removed by hydrolysis with a dilute methanol solution of potassium hydroxide. Therefore, it was considered that PPG was grafted onto the ferrite surface with urethane bond. The grafting of PPG onto the surface was also confirmed by infrared spectra. The reaction of PPG-NCO with the ferrite was accelerated by the addition of-picoline as a catalyst. PPG-grafted ferrite was found to produce a stable colloidal dispersion in organic solvents. Furthermore, the effect of molecular weight of PPG-NCO on the grafting onto the ferrite was discussed.     

Electrokinetic study on concentrated suspensions using colloid vibration potential measurements

-potentials of a silica suspension and three types of polystyrene latex suspensions with different surface charge groups were measured, as a function of the particle concentration () in the suspension over a wide range, using the colloid vibration potential (CVP) technique. The concentration dependence of the-potential in silica suspension is explained well by Levine et al.s [1] cell model theory, verifying the applicability of the cell model to the CVP in silica suspension. However, the-potential of latex suspensions ordinarily decreases as the particle concentration increases, even after being corrected by the term of (1-). This tendency is especially noticeable in the systems that have particles with high surface charge densities. Furthermore, the conductivity measurements of these suspensions reveal that the conductivity of these systems, especially in their highly charged state, increases as the particle concentration is increased; opposite in tendency to silica suspensions. These new findings can be explained as follows: on the highly charged surface of a latex particle, a polyelectrolyte-like (hairy) layer is present, which overlaps at some point. This permits interparticle surface conduction and results in the abnormal behavior of CVP in these systems.     

Lamellar phases in mixtures of low molecular weight alkanols and cetyltrimethylammonium bromide (CTAB)

Partial phase diagrams showing the domains of existence of a transparent, viscous, lamellar-structured (D)-phase that transforms reversibly into fluid single phase solutions at high temperature are presented for the system: cetyltrimethylammonium bromide (CTAB), two low molecular weight alcohols, and water with and without additives. At constant temperature and with a fixed amount of surfactant, the size and location of this phase in the phase diagram depends upon three composition variables: i) the ratio of concentrations of medium chain alcohol to long chain alcohol (R), ii) the ratio of concentrations of medium chain alcohol to surfactant (R), and iii) the concentrations of small amounts (up to 10 % by weight) of additives such as ethylene glycol, propylene glycol, and dimethylformamide, as well as NaBr. Small-angle x-ray scattering measurements of these mixtures reveal a lamellar structure. The observed lamellar repeat distances range from 60 A to 290 Å and depend upon the ratiosR andR and the concentration of the additives. The mechanical and structural properties of theseD-phases can be tuned by adjustingR andR. TheD-phase-to-isotropic transition temperature can be varied from near room temperature to above 80 °C by adjustingR andR.