Thin‐film Potentiometric Sensor to Detect CO2 Concentrations Ranging Between 2 % and 100 %

A potentiometric thin‐film sensor to detect CO₂ in a wide range (2–100 %) has been developed. The system has been fabricated depositing a reference electrode of Pt, a solid electrolyte of YSZ (Yttria‐stabilized Zirconia), a sensing phase made of Li₂CO₃ and a working electrode of Au via Physical Vapor Deposition (PVD). Characterization of the different elements has provided the optimal fabrication parameters and the system response for CO₂ concentrations can be measured from 2 to 100 % at 450 °C. The sensor behaves as a non‐Nerstian system and slightly deviates from a linear response with the logarithm of CO₂ until the CO₂ concentration reaches the 30 %. Higher CO₂ amounts make the response divert more from the Nernst law but give a stable and reproducible response to CO₂ in a wide range of concentrations. Based on these promising results the recovery time, stability, repeatability and selectivity of the sensor have been measured. The performance showed by the thin film sensor proves the feasibility of the use of this system for biogas and natural gas applications owing to its very good consistency at low temperature in a wide concentration range.     

Ni控制掺杂TiO2薄膜的光电化学及光催化活性

采用溶胶-凝胶法通过分步控制工艺制备了镍离子不同掺杂方式的TiO₂薄膜。通过甲基橙的光催化降解动力学来表征其光催化活性。结果表明：镍离子非均匀掺杂在掺杂量0.5%时可以明显增强TiO₂的光催化活性，而均匀掺杂提高TiO₂的光催化活性较小。光电化学表征结果显示：镍离子非均匀掺杂TiO₂薄膜的瞬时光电流信号较强，说明其光生载流子易于生成且分离效果较好；循环伏安曲线表明，光照时Ni非均匀掺杂的TiO₂薄膜改变了体系的氧化还原电位，说明了薄膜内建电场的建立。基于半导体的P-N结原理探讨了镍离子非均匀掺杂TiO₂薄膜的光催化活性机理。     

Lowering the dielectric constant of polyimide thin films by swelling with supercritical carbon dioxide

The swelling with supercritical carbon dioxide (sc‐CO₂) of thin films of polyimides having various structures was investigated. It was shown that the degree of swelling is significantly influenced by the solvent which was used for the synthesis of those polyimides, by the solvent which was used for the preparation of thin films and by the conformational rigidity of the polymers. The presence of hexafluoroisopropylidene groups in the main chain of a polymer prevents its swelling with sc‐CO₂. The best results were obtained for polyimide film ULTEM, based on m‐phenylene‐diamine and isopropylidene‐diphenoxy‐bis(phthalic anhydride), synthesized in benzoic acid, whose free volume increased twice and its dielectric constant decreased from 3.15 to 2.45 by swelling with sc‐CO₂. Copyright © 2013 John Wiley & Sons, Ltd.     

Study of the pseudo-steady-state kinetics of CO2 hydrate formation and stability

This article describes a dynamic model for formation and stability of CO₂-hydrate on the interface of liquid CO₂(LCO₂) and ocean water at large depths. Experimental results indicate that a thin film of hydrate naturally forms on the interfaces between LCO₂ and water, and inhibits diffusion between the two phases. Experiments further shows that the flux of CO₂ through the hydrate film is dependent of the CO₂-concentration in the ambient sea water. The model proposed here explains these phenomena by introducing four major mechanisms; diffusion of water to the LCO₂-phase, formation of hydrate in the LCO₂-hydrate interface, decay of hydrate in the water-hydrate interface, and diffusion of CO₂ through the water phase. The model explains the CO₂ flux not by diffusion through the hydrate film, but suggest a mechanism of continuous hydrate formation and decay. The overall effect is a “moving,” pseudo-steady-state hydrate film due to transport of CO₂ through the film. The film velocity is dependent of liquid-liquid diffusivity parameters and reaction constant, and lacking experimental values of these parameters, an order–of-magnitude analysis is done by fitting the model to experimentally obtained data for the overall film velocity. The motivation for this work is to elucidate options for CO₂ depositions in deep oceans, of which liquid CO2 sequestration is believed to be one of the most feasible. Spreading of CO₂ from a liquid CO₂-lake and associated lowering of pH in the ecosystem surrounding the lake is of large concern. The work presented here concludes that diffusion of CO₂ in the ocean is largely reduced by the hydrate film and suggests that hydrate formation may alleviate some of the environmental concerns regarding deep ocean sequestration of liquid CO₂. © 1994 John Wiley & Sons, Inc.     

Use of various filters for generating modified supercritical fluid mobile phases

Summary Adding various components to supercritical carbon dioxide in supercritical fluid chromatography can extend or significantly alter the solvating properties. Polar samples which are difficult to analyze with pure supercritical CO₂ because of their high polarity can be separated by addidng polar modifiers. In this paper, a new mixing method using an HPLC filter for adding polar modifier to CO₂ is described. Although several filters were tried, only one could keep the amount of modifier in the mobile phase constant for a long time. The amount of water or methanol dissolved in supercritical CO₂ was measured by an amperometric microsensor made of a thin film of perfluorosulfonate ionomer (PFSI).     

Electrochemical and FTIR spectroscopic study of CO2 reduction at a nanostructured Cu/reduced graphene oxide thin film

Here we report a facile approach to synthesize a novel nanostructured thin film comprising Cu nanoparticles (NPs) and reduced graphene oxide (rGO) on a glassy carbon electrode (GCE) via the direct electrochemical reduction of a mixture of cupper and graphene oxide (GO) precursors. The effect of the applied potential on the electrochemical reduction of CO₂ was investigated using linear sweep voltammetric (LSV) and chronoamperometric (CA) techniques. Carbon monoxide and formate were found as the main products based on our GC and HPLC analysis. The electrochemical reduction of CO₂ at the Cu/rGO thin film was further studied using in situ ATR-FTIR spectroscopy to identify the liquid product formed at different applied cathodic potentials. Our experimental measurements have shown that the nanostructured Cu/rGO thin film exhibits an excellent stability and superb catalytic activity for the electrochemical reduction of CO₂ in an aqueous solution with a high current efficiency of 69.4% at − 0.6 V vs. RHE, promising for the efficient electrochemical conversion of CO₂ to valuable products.     

Characterization of TiO2 nanotube arrays prepared via anodization of titanium films deposited by DC magnetron sputtering

Highly ordered TiO₂ nanotube arrays were fabricated on a conducting glass substrate in NH₄HF₂/glycol electrolyte via anodization of titanium film which was deposited by direct current magnetron sputtering (DCMS) at different temperatures. The results showed that Ti films with good homogeneity and high denseness could be formed under the conditions Ar pressure 0.35 Pa, direct current 3.5 A, and 2 h at 300 °C. Characterization of the TiO₂ nanotube arrays was investigated comparatively, by altering anodization time. The surface morphology of the samples changed as the anodization time was prolonged from 10 to 150 min at 30 V. The TiO₂ thin film was amorphous and could be transformed into anatase by annealing at 450 °C. On the basis of UV?Cvisible transmission spectra the bandgap of the thin film was calculated to be 3.12 eV, and its tail extended to 2.6 eV.     

New Device for Adding Polar Modifiers to Carbon Dioxide Mobile Phase for Supercritical Fluid Chromatography

Abstract

Adding additional components to supercritical carbon dioxide in supercritical fluid chromatography can extend or significantly alter the fluid solvating properties. Polar samples which are difficult to be analyzed with pure supercritical CO₂ because of their high polarity can be separated by adding polar modifiers to supercritical CO₂. In this paper, a new mixing device using a teflon high capacity filter for adding polar modifiers to carbon dioxide mobile phase is introduced. This new mixing device could keep the amount of modifier in the mobile phase constant for a much longer time than a saturator column. The amount of water or methanol dissolved in supercritical CO₂ was measured by amperometric microsensor which is made of thin film of perfluorosulfonate ionomer(PFSI).     

Low-temperature synthesis of photocatalytic TiO2 thin film from aqueous anatase precursor sols

Anatase TiO₂ sols (RS) were synthesized by peptizing the hydrolysis of titanyl sulfate in abundant hydrogen peroxide solution and subsequent reflux to enhance crystallization. The influences of various reflux time on crystallinity, morphology, and size of the obtained TiO₂ sol and dried TiO₂ film particles were investigated. At room temperature, crystalline TiO₂ thin film was deposited on glass silde from the as prepared TiO₂ sol by dip-coating method. No further thermal posttreatment was required to eliminate organics from the film or to induce titania crystallization. TiO₂ thin film on substrates could be thickened by means of consecutive dip-coating process. Titania film thus obtained was transparent and showed proper adherence. The photocatalytic activities of the TiO₂ thin film was assessed by the degradation of methyl orange in aqueous solution. The preparation process of photocatalytic TiO₂ thin film was quite simple and a low-temperature route.     

Analysis of polystyrene surface properties on thin film bonding under carbon dioxide pressure using nanoparticle embedding technique

A gold nanoparticle embedding technique is used to determine how vacuum and pressured carbon dioxide (CO₂) affect polystyrene (PS) thin film properties. The pressured CO₂ greatly increased the gold nanoparticle embedding depth, possibly due to a low cohesive energy density near the film surface. For the monodisperse PS used in this study (M_n = 214,000), two spin‐coated thin films with intimate contact can be bonded below the bulk glass transition temperature (T_g) under CO₂ pressure when the embedded depth is larger than half of the gyration radius of PS molecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1535–1542, 2009     

Nanofibrous polyaniline thin film prepared by plasma‐induced polymerization technique for detection of NO2 gas

A nanofibrous polyaniline (PANI) thin film was fabricated using plasma‐induced polymerization method and explored its application in the fabrication of NO₂ gas sensor. The effects of substrate position, pressure, and the number of plasma pulses on the PANI film growth rate were monitored and an optimum condition for the PANI thin film preparation was established. The resulting PANI film was characterized with UV–visible spectrophotometer, FTIR, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The PANI thin film possessed nanofibers with a diameter ranging from 15 to 20 nm. The NO₂ gas sensing behavior was studied by measuring the change in electrical conductivity of PANI film with respect to NO₂ gas concentration and exposure time. The optimized sensor exhibited a sensitivity factor of 206 with a response time of 23 sec. The NO₂ gas sensor using nanofibrous PANI thin film as sensing probe showed a linear current response to the NO₂ gas concentration in the range of 10–100 ppm. Copyright © 2009 John Wiley & Sons, Ltd.     

Aqueous Photoelectrochemical CO2 Reduction to CO and Methanol over a Silicon Photocathode Functionalized with a Cobalt Phthalocyanine Molecular Catalyst

We report a precious-metal-free molecular catalyst-based photocathode that is active for aqueous CO₂ reduction to CO and methanol. The photoelectrode is composed of cobalt phthalocyanine molecules anchored on graphene oxide which is integrated via a (3-aminopropyl)triethoxysilane linker to p-type silicon protected by a thin film of titanium dioxide. The photocathode reduces CO₂ to CO with high selectivity at potentials as mild as 0 V versus the reversible hydrogen electrode (vs RHE). Methanol production is observed at an onset potential of −0.36 V vs RHE, and reaches a peak turnover frequency of 0.18 s⁻¹. To date, this is the only molecular catalyst-based photoelectrode that is active for the six-electron reduction of CO₂ to methanol. This work puts forth a strategy for interfacing molecular catalysts to p-type semiconductors and demonstrates state-of-the-art performance for photoelectrochemical CO₂ reduction to CO and methanol.     

Fabrication of Ordered TiO2 Porous Thin Films by Sol-Dipping PS Template Method

Monolayer polystyrene spheres (∼400 nm) array templates were assembled orderly on clean glass substrates by dip-drawing method from emulsion of PS and porous TiO₂ thin films were prepared by using sol-dipping template method to fill TiO₂ sol into the interstices among the close-packed PS templates and then annealing to remove the PS templates. The effects of TiO₂ precursor sol concentration and dipping time in sol on the porous structure of the thin films were studied. The results showed pore size of the ordered TiO₂ porous thin film depended mainly on PS size and partly on TiO₂ sol concentration. The shrinkage of pore diameter was about 10% for 0.2 M and 20% for 0.4 M TiO₂ sol concentrations. X-ray diffraction (XRD) spectra indicated the porous thin film was anatase structure. The transmittance spectrum showed that optical transmittance of the porous thin film kept above 70% beyond the wavelength of 430 nm. Optical band-gap of the porous TiO₂ thin film (fired at 550^∘;C) was 3.12 eV.     

Kinetics and mechanism of the formation of CO2 hydrate

This article proposes a mechanism of CO₂ hydrate formation taking into account both diffusion and reaction, and gives an analysis of its kinetics. The most important assumptions on the model are that water dissolves into liquid CO₂ and reacts to form CO₂ hydrate, and that the hydrate blocks the dissolution and diffusion of water. Computational simulations were conducted, and the model proposed explains well the many observations on the CO₂ hydrate formation in previous articles. It is concluded that liquid CO₂ disposed in a deep ocean will form a very thin film of CO₂ hydrate, and this will greatly control the CO₂ diffusion in the ocean. © 1993 John Wiley & Sons, Inc.     

Kinetics on the dissolution of CO2 into water from the surface of CO2 hydrate at high pressure

Kinetic study on the dissolution of CO₂ from the surface of a liquid CO₂ droplet in water was conducted, and a mechanism of the decay of CO₂ hydrate was proposed. The model was applied to the experimental data which showed that the radius of liquid CO₂ droplets in water reduced linearly with time. It was proved that the dissolution rate of CO₂ into water is dominated by the decay of CO₂ hydrate on the surface of the droplet. The rate constant of the decay of CO₂ hydrate was estimated to be 1.25 × 10^?6 m s^?1. From a viewpoint of liquid CO₂ disposal in the deep ocean, it is predicted that the thin membrane of CO₂ hydrate at the interface between seawater and liquid CO₂ will control the dissolution of CO₂ into seawater. © 1995 John Wiley & Sons, Inc.     

Soft solution synthesis of a zinc oxide nano-screw superstructure and its composite with nitrogen-doped titania

Novel zinc oxide thin films with nano-screw superstructure were prepared via a soft solution route without any polymer additives. A ZnO thin film could be produced directly on the substrates. The ZnO thin film with nano-screw superstructure was prepared using visible-light-induced nitrogen-doped titania nano-particles. The ZnO nano-screw/TiO_2−x N _y composite film showed excellent photocatalytic deNO _x ability and quantum efficient.     

In situ FTIR spectroscopic studies of CO adsorption on electrodes with nanometer-scale thin films of ruthenium in sulfuric acid solutions

A nanometer-scale thin film of ruthenium supported on glassy carbon (nm-Ru/GC) was prepared by electrochemical deposition under cyclic voltammetric conditions. Scanning tunneling microscopy (STM) was used to investigate the structure and to measure the thickness of the thin film. It has been found that the Ru thin film is composed of layered Ru crystallites that appear in a hexagonal form with dimensions of about 250 nm and thickness around 30 nm. In situ FTIR spectroscopic studies demonstrated that such a nanostructured Ru thin film exhibits abnormal infrared effects (AIREs) for CO adsorption (G.Q. Lu et al., Langmuir 16 (2000) 778). In comparison with CO adsorbed on a massive Pt electrode, the IR absorption of CO_ad on nm-Ru/GC was significantly enhanced. Moreover, the direction of CO_ad bands is inverted and the full width at half maximum of CO_ad bands is increased. It has been revealed that the enhancement factor of IR absorption of CO adsorbed on nm-Ru/GC electrodes depends strongly on the thickness of the Ru film. An asymmetrical volcano relationship between the enhancement factor and the thickness of the Ru film has been obtained. The maximum value of the enhancement factor was measured as 25.5 on a nm-Ru/GC electrode of Ru film thickness around 86 nm. The present study has contributed to exploration of the particular properties of nanostructured Ru film material and to the origin of the abnormal infrared effects.     

Nitrogen-doped TiO2 from TiN and its visible light photoelectrochemical properties

Homogeneous titanium nitride (TiN) thin film was produced by simple electrophoreic deposition process on Ti substrate in an aqueous suspension of nanosized TiN powder. Nitrogen-doped titanium dioxide (TiO_2−xN_x) was synthesized by oxidative annealing the resulted TiN thin film in air. Photoelectrochemical measurements demonstrated visible light photoresponse for the electrode of annealed electrophoreic deposited TiN samples. It is found that the synthesized TiO_2−xN_x electrode showed higher photo potential under white and visible light illumination than the pure TiO₂ electrode. The photocurrent under visible light illumination was also observed, which increased with the increase of deposition time of TiN thin films.     

Preparation of grain size controlled boron-doped diamond thin films and their applications in selective detection of glucose in basic solutions

Boron-doped diamond (BDD) thin films with different crystal grain sizes were prepared by controlling the reacting gas pressure using hot filament chemical vapor deposition (HFCVD). The morphologies and structures of the prepared diamond thin films were characterized by scanning electron microscopy (SEM) and Raman spectroscopy. The electrochemical responses of K₄Fe(CN)₆ on different BDD electrodes were investigated. The results suggested that electron transfer was faster at the boron-doped nanocrystalline diamond (BDND) thin film electrodes in comparison with that at other BDD thin film electrodes. The prepared BDD thin film electrodes without any modification were used to directly detect glucose in the basic solution. The results showed that the as-prepared BDD thin film electrodes exhibited good selectivity for detecting glucose in the presence of ascorbic acid (AA) and uric acid (UA). The higher sensitivity was observed on the BDND thin film grown on the boron-doped microcrystalline diamond (BDMD) thin film surface, and the linear response range, sensitivity and the low detection limit were 0.25–10 mM, 189.1 μA mmo^?1 cm^?2 and 25 μM (S/N=3) for glucose in the presence of AA and UA, respectively.     

Thermal properties and moisture absorption of nanofillers‐filled epoxy composite thin film for electronic application

This current study aimed to enhance the thermal conductivity of thin film composites without compromising other polymer qualities. The effect of adding high thermal conductivity nanoparticles on the thermal properties and moisture absorption of thin film epoxy composites was investigated. Three types of fillers in nanosize with high thermal conductivity properties, boron nitride (BN), synthetic diamond (SD), and silicon nitride (Si₃N₄) were studied. SN was later used as an abbreviation for Si₃N₄. The contents of fillers varied between 0 and 2 vol.%. An epoxy nanocomposite solution filled with high thermal conductivity fillers was spun at 1500–2000 rpm to produce thin film 40–60 µm thick. The effects of the fillers on thermal properties and moisture absorption were studied. The addition of 2 vol.% SD produced the largest improvement with 78% increment in thermal conductivity compared with the unfilled epoxy. SD‐filled epoxy thin film also showed good thermal stability with the lowest coefficients of thermal expansion, 19 and 124 ppm, before and after T_g, respectively, which are much lower compared with SN‐filled and BN‐filled epoxy thin film composites. However the SD‐filled epoxy film has its drawback as it absorbs more moisture compared with BN‐filled and SN‐filled epoxy film. Copyright © 2012 John Wiley & Sons, Ltd.