酸性湖蓝7在LDO上吸附性能及机理的研究

探讨了Mg/Al＝3的水滑石焙烧产物(MgAl-LDO)对染料酸性湖蓝7(AB7)的吸附性能及其机理. 考察了不同因素对MgAl-LDO吸附AB7性能的影响, 并研究了吸附过程的热力学机理. 实验结果表明: MgAl-LDO对AB7具有优异的吸附性能, 在288 K, pH＝6.74条件下, 0.33 g·L^-1 MgAl-LDO对150 mg·L^-1AB7溶液的吸附容量和去除率分别达到446.9 mg·g^-1和99.31%. 热力学研究表明: MgAl-LDO对AB7的吸附过程同时符合Langmuir 和 Freundlich等温吸附方程, 并且是个放热、自发的过程. 计算所得的吉布斯自由能绝对值在8～10 kJ·mol^-1, 这主要是由染料分子与水滑石层板的氢键作用产生, 结合Materials Studio 5.5软件模拟AB7染料分子在MgAl-LDHs上的排列分布, 推测MgAl-LDO对AB7的吸附机理是表面吸附作用. 同时, 经4次回收, LDO对AB7的去除率仍达到85%以上.     

阴离子型有机化合物在LDHs上的动力学和热力学研究

考察了水滑石焙烧产物MgAl-LDO吸附3种阴离子染料Acid Red 88(AR88)、Acid Orange 3(AO3)、Acid Violet 90(AV90)过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明:MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15 kJ·mol-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合Materials Studio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附(占优势)与层间插层的协同作用。     

Mg/Al-NO_3 LDH吸附诺氟沙星的热力学和动力学研究

采用平衡吸附实验,研究了诺氟沙星在自制焙烧态镁铝水滑石(Mg/Al-NO_3 LDH)上的吸附热力学和动力学行为。结果表明,在固液比1∶500、p H=5.0、吸附温度25℃、离子强度0.1 mol/L的条件下,吸附1 h对诺氟沙星(20 mg/L)的吸附过程符合Langmuir等温线方程和准二级动力学,理论平衡吸附量达到32.05 mg/g。其热力学参数ΔG0 KJ/mol,ΔH0 KJ/mol,由此推断焙烧态镁铝水滑石对诺氟沙星的吸附是自发放热反应。     

AB24在MgAl-LDO上的吸附性能及机理研究

本文探讨了nMg/nAl=3的水滑石焙烧产物(MgAl-LDO)对染料酸性黑24(AB24)的吸附性能及其机理。考察了不同因素对MgAl-LDO吸附AB24性能的影响,并研究了吸附过程的热力学和动力学机理。实验结果表明:MgAl-LDO对AB24具有优异的吸附性能,在298 K,pH=10条件下,1.0 g.L-1MgAl-LDO对1 000 mg.L-1AB24溶液的吸附容量和去除率分别达到998.31 mg.g-1和99.83%。动力学和热力学研究表明:MgAl-LDO对AB24的吸附过程同时符合Langmuir和Freundlich等温吸附方程,并且是个放热、自发的过程。计算所得的吉布斯自由能绝对值在10~15 kJ.mol-1,这主要是由染料分子与水滑石层板的氢键作用产生,结合Materials Studio 5.5软件模拟AB24染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对AB24的吸附机理是表面吸附(占优势)与层间插层的协同作用。同时,该吸附过程符合准二级反应动力学模型。     

阴离子型有机化合物在LDHs上的动力学和热力学研究

本文考察水滑石焙烧产物MgAl-LDO吸附3种阴离子染料AcidRed88（AR88）、AcidOrange 3（AO3）、AcidViolet90（AV90）过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明：MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15kJ·mol^-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合MaterialsStudio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附（占优势）与层间插层的协同作用。     

镁铝类水滑石对阳离子染料中性红的吸附及机理研究

研究了镁铝类水滑石对中性红的吸附及其作用机理,考察了时间、pH、温度、电解质浓度等因素对吸附作用的影响。结果表明,镁铝类水滑石对中性红的吸附动力学符合准二级动力学方程,热力学符合Langmuir吸附等温式。在实验范围内,吸附量随溶液pH的增大而增加,随温度的升高而降低,随电解质浓度的增加先增加后降低。吸附过程是放热、熵减小的自发过程。镁铝类水滑石对中性红的吸附缘于为类水滑石与中性红分子中π电子的较强静电吸引作用。     

Mg/Fe类水滑石的磷酸根吸附性能及吸附机理

采用共沉淀法成功制备了Mg/Fe类水滑石(Mg/Fe-hlc),并研究了其对废水中磷酸根的吸附性能及吸附机理。研究结果表明:制备的Mg/Fe-hlc具有典型的类水滑石结构和较大的比表面积(156.7 m~2·g~(-1));Mg/Fe-hlc对磷酸根的吸附动力学过程符合准二级动力学模型;Langmuir和Tempkin方程都可以很好地拟合Mg/Fe-hlc对磷酸根的等温吸附数据,Langmuir方程拟合得到的最大吸附量可达47.38 mg·g~(-1);共存阴离子NO_3~-、Cl~-和SO_4~(2-)对磷吸附性能的影响很小;通过分析吸附磷酸根前后的Mg/Fe-hlc的结构和织构性质以及表面官能团变化,并结合溶液pH对磷酸根吸附影响实验结果,发现静电相互作用、配体交换和阴离子交换是Mg/Fe-htl吸附磷酸根的三种主要机制。     

焙烧态镁铝水滑石对诺氟沙星的吸附行为研究

采用共沉淀法合成镁铝水滑石(LDH),用X-射线衍射(XRD)、扫描电镜(SEM)等表征了产物,研究了400℃焙烧后LDH(LDO)的结构、成分及吸附率的变化,通过静态吸附实验考察了LDO对诺氟沙星的吸附性能。结果表明,在固液比1∶500、pH=5.0、吸附温度25℃、离子强度0.1 mol/L的条件下吸附1 h对诺氟沙星(20 mg/L)的吸附率达91.25%。吸附过程符合Langmuir等温线方程,理论平衡吸附量达到32.05 mg/g,推断焙烧态镁铝水滑石对诺氟沙星的吸附是以表面吸附为主的自发反应。     

氨基功能化离子印迹硅胶对Cd2 的吸附行为及机理

研究了氨基功能化离子印迹硅胶对Cd2+的吸附行为及机理,进行了等温吸附模型和吸附动力学的测定和吸附热力学计算。结果表明,饱和吸附量的实验值为30.7mg/g;20min即可达到吸附平衡;等温吸附曲线符合Langmuir等温吸附模型,吸附过程以单层吸附为主;Cd2+的吸附动力学数据均符合准二级反应动力学模型;反应的吉布斯自由能为负值,焓变为23.01k J/mol,熵变为104.1J/mol·K,说明吸附是一个吸热的自发进行的过程。     

镁铝二元水滑石的焙烧产物对染料废水酸性红88的吸附

研究了镁铝水滑石的焙烧产物(LDO)对阴离子染料废水酸性红88(AR88)的吸附特征。分别考察了染料的初始浓度、吸附剂投加量、初始pH值、反应温度和竞争离子等因素的影响,并用XRD、红外光谱对水滑石以及吸附前后的LDO进行了表征。实验结果表明：LDO对高浓度的AR88具有良好的去除效果,在15 ℃、pH=10～11下,1.0 g·L^-1的LDO对浓度为2 000 mg·L^-1的AR88的去除率可高达99.95%,吸附容量为1 999.0 mg·g^-1。经4次回收重复利用的LDO对AR88的去除率仍为90%以上。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.