聚合物电解质在染料敏化太阳能电池中的应用进展

染料敏化太阳能电池(DSSC)由于成本低、污染小、制备工艺简单而受到广泛关注。电解质在其中起到桥梁的作用,能促使染料再生、输运空穴,从而完成整个光电循环过程,是DSSC重要的组成部分。本文简要介绍了DSSC的基本结构和工作原理,指出了传统液态电解质存在的问题,综述了近年来以聚合物为基体制备的新型固态聚合物电解质、凝胶聚合物电解质以及多孔聚合物电解质在DSSC中的应用,最后对聚合物电解质在染料敏化太阳能电池中的发展做出了展望。     

聚合物固态电解质–高电压正极界面稳定性研究进展

聚合物固态电解质相比于液态电解质表现出更良好的热稳定性,并且对比无机固态电解质具有机械性能好、耐候性好和易加工成型等特点,因此在下一代高能量密度储能装置中极具应用潜能.然而,固态电解质与正负极材料之间的界面稳定性问题阻碍了其实际应用.本文总结了锂离子聚合物固态电解质的关键特性,讨论了聚合物固态电解质与高电压正极的普遍界面问题,包括界面接触不良与界面不稳定问题.分析了导致高电压富镍氧化物正极材料与聚合物固态电解质严重界面问题的主要因素,针对相关因素总结了缓解界面问题的有效策略,并展望了未来聚合物固态电解质与富镍层状氧化物的界面性能提升的研究方向,为基于聚合物固态电解质与高电压正极材料固态锂电池的研究提供参考.     

聚合物/TiO2杂化纳米纤维微孔膜的制备及其在染料敏化太阳能电池中的应用

利用静电纺丝技术,制备了不同的聚合物/TiO2杂化纳米纤维微孔膜,吸附液体电解质后形成聚合物/TiO2杂化纳米纤维微孔膜准固态电解质,应用于制备准固态染料敏化太阳能电池(DSSCs).测试了电纺聚合物纳米纤维微孔膜电解质的吸液率、孔隙率、离子电导率等参数,研究了纳米纤维微孔膜准固态电解质DSSCs的光伏性能.结果显示,TiO2的掺入可提高聚合物/TiO2杂化纳米纤维微孔膜对液态电解质的浸润扩散性能,从而提高纳米纤维微孔膜对液态电解质的吸附能力.组装的DSSCs的光电转换效率可达液态电解质的90%以上,并具有较好的长期工作稳定性.     

固态聚合物电解质的锂离子传导机理与研究进展

锂离子电池(lithiumionbatteries,LIBs)在储能领域已取得了巨大的成功.然而,商用LIBs含有高挥发性易燃有机电解液,使其存在严重的安全隐患.固态聚合物电解质具有解决相应安全性问题的潜力,有望成为下一代高安全性全固态LIBs的电解质材料.然而,固态聚合物电解质存在离子电导率不高等问题,限制了其在固态LIBs中的实际应用.研究者们为了提高该类电解质的离子电导率、锂离子迁移数等综合电化学性能,已在寻找新锂盐、对聚合物进行改性以及向聚合物电解质中添加填料等方面进行了较多的研究.本文简要概述了固态聚合物电解质的锂离子传导机理以及在提高固态聚合物电解质综合电化学性能方面的研究进展.     

染料敏化太阳电池用聚合物电解质

综述了本研究小组近年来用于染料敏化太阳电池中聚合物电解质的研究概况.设计合成了几类性能优良的聚合物电解质,较好地改进了液体电解质染料敏化太阳电池(DSSC)的使用稳定性,研究结果具有实际应用的价值,并提出了此领域研究今后的发展方向.     

聚碳酸酯基固态聚合物电解质的研究进展

液态锂离子电池由于采用易泄露、易挥发、易燃烧的碳酸酯有机溶剂,在高温或极端条件下使用时,存在极大的安全隐患.使用固态电解质替代液态电解液,可以从根本上避免此类安全问题的发生,与此同时还可以大幅度提升固态锂电池的能量密度.固态电解质又分为无机固态电解质和聚合物固态电解质2大类.无机固态电解质能够在宽的温度范围内保持化学稳定性,并且电化学窗口较宽,机械强度更高,室温离子电导率较高,但脆性较大,柔韧性差,制备工艺复杂,成本较高.聚合物固态电解质,室温离子电导率偏低,难以满足室温锂离子电池的应用,但其加工成型容易,形状可变.比较而言,固态聚合物电解质,更适宜大规模生产,离产业化相对更近.固态聚合物电解质中研究较多的是聚醚基固态聚合物电解质(如聚环氧乙烷和聚环氧丙烷),但其缺点是室温离子电导率低,需要对其改性或进一步开发综合性能更加优异的其他固态聚合物电解质.聚碳酸酯基固态聚合物电解质由于其特殊的分子结构(含有强极性碳酸酯基团)以及高介电常数,可以有效减弱阴阳离子间的相互作用,提高载流子数量,从而提高离子电导率,因此被认为是一类非常有前途的固态聚合物电解质体系.基于此,本文重点综述了最近研究热点的聚碳酸酯基固态聚合物电解质,包括聚(三亚甲基碳酸酯)体系、聚(碳酸丙烯酯)体系、聚(碳酸乙烯酯)体系和聚(碳酸亚乙烯酯)体系等,并详细阐述了上述每种聚碳酸酯基固态聚合物电解质的制备、电化学性能、优缺点及改性手段,归纳出其离子配位-解配位过程和离子扩散机制,还对聚碳酸酯基固态聚合物电解质的未来发展方向和研究趋势望进行了预测和展望.     

PAN-LATP复合固态电解质的制备与性能表征

与传统的液态电解质相比,固态聚合物电解质可以显著提高锂二次电池的安全性和能量密度,但其室温锂离子传导率低、机械性能比较差,这些缺点限制了固态聚合物电解质在锂二次电池中的应用.为了解决上述问题,本文采用溶液浇铸法在聚丙烯腈(PAN)固态聚合物电解质中引入无机固态电解质Li_(1.3)Al_(0.3)Ti_(1.7)(PO_4)_3(LATP)制备了PAN-LATP复合固态电解质(CSE).该复合固态电解质不仅具有较高的锂离子电导率,还拓宽了电化学稳定窗口.当LATP含量为15%时CSE的锂离子传导率最高,室温下为2.14×10~(-5)S/cm,333 K时为3.03×10~(-4)S/cm.与此同时,固态聚合物电解质的机械强度也得到了很好的改善.结果表明该性能优良的固态电解质有望用于锂离子电池和其他电化学储能系统.     

电解质在超级电容器中的应用

超级电容器作为一种新型储能装置,因充放电快、功率密度高和循环寿命长的优异性能而引起了广泛的关注。电解质作为影响超级电容器性能的关键因素之一,其离子类型与尺寸、电化学窗口及电导率等性质对器件的工作电压、能量密度及循环寿命有着重要影响。针对近年来的研究现状,本文概述了超级电容器的储能原理、性能评估的关键参数及电解质在超级电容器中的应用研究进展。介绍了电解质的分类,包括水系电解质、有机电解质、离子液电解质和氧化还原电解质在内的液态电解质,及包括固态聚合物电解质、无机固态电解质及凝胶聚合物电解质在内的固态/准固态电解质。评述各类电解质的最新研发进展,讨论了电解质性质对超级电容器性能的影响,并阐明了超级电容器电解质的设计和优化方法。最后,分析了制备高性能电解质所面临的困难,并就其未来的研究方向作出了展望。     

基于聚乙二醇接枝丙烯酸树酯光固化电解质的制备及性能研究

聚氧化乙烯(PEO)(聚乙二醇(PEG))和丙烯酸树脂在聚合物基电解质中具有很好的应用,本文通过紫外光引发单/双官能度的聚乙二醇接枝丙烯酸树脂单体聚合构建了离子电导率高、易于封装,可避免电解质泄漏的准固态聚合物电解质.通过调控聚乙二醇二甲基丙烯酸酯(PEGDA)和甲氧基聚乙二醇单甲基丙烯酸酯(PEGMA)2种单体的比例以及锂盐溶液的含量,成功制备出具有高离电导率的准固态聚合物电解质.采用傅里叶变换红外光谱仪(FTIR),电化学工作站对PEGMA/PEGDA基聚合物电解质进行表征,研究各组分比例对电解质的电化学性能影响.当PEGMA/PEGDA单体比例为75/25,锂盐溶液的占比为75%时,形成的薄膜状态电解质表现出1.96×10^?3 S·cm^?1的高离子电导率,较原始配比提高了14倍.将制备的电解质应用于电致变色器件,在580个变色循环后,器件依然可以实现稳定快速的颜色切换,2种颜色变换时间均在3 s以内,本文中研究的聚醚接枝丙烯酸树酯基电解质材料在电致变色器件中有较好的应用前景.     

基于聚乙二醇接枝丙烯酸树酯光固化电解质的制备及性能研究

聚氧化乙烯(PEO)(聚乙二醇(PEG))和丙烯酸树脂在聚合物基电解质中具有很好的应用,本文通过紫外光引发单/双官能度的聚乙二醇接枝丙烯酸树脂单体聚合构建了离子电导率高、易于封装,可避免电解质泄漏的准固态聚合物电解质.通过调控聚乙二醇二甲基丙烯酸酯(PEGDA)和甲氧基聚乙二醇单甲基丙烯酸酯(PEGMA) 2种单体的比例以及锂盐溶液的含量,成功制备出具有高离电导率的准固态聚合物电解质.采用傅里叶变换红外光谱仪(FTIR),电化学工作站对PEGMA/PEGDA基聚合物电解质进行表征,研究各组分比例对电解质的电化学性能影响.当PEGMA/PEGDA单体比例为75/25,锂盐溶液的占比为75%时,形成的薄膜状态电解质表现出1.96×10~(-3)S·cm~(-1)的高离子电导率,较原始配比提高了14倍.将制备的电解质应用于电致变色器件,在580个变色循环后,器件依然可以实现稳定快速的颜色切换,2种颜色变换时间均在3 s以内,本文中研究的聚醚接枝丙烯酸树酯基电解质材料在电致变色器件中有较好的应用前景.     

Recent research progress on quasi-solid-state electrolytes for dye-sensitized solar cells

Dye-sensitized solar cells(DSSCs) are the most promising, low cost and most extensively investigated solar cells. They are famous for their clean and efficient solar energy conversion. Nevertheless this, long-time stability is still to be acquired. In recent years research on solid and quasi-solid state electrolytes is extensively increased. Various quasi-solid electrolytes, including composites polymer electrolytes, ionic liquid electrolytes,thermoplastic polymer electrolytes and thermosetting polymer electrolytes have been used. Performance and stability of a quasi-solid state electrolyte are between liquid and solid electrolytes. High photovoltaic performances of QS-DSSCs along better long-term stability can be obtained by designing and optimizing quasi-solid electrolytes. It is a prospective candidate for highly efficient and stable DSSCs.     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

新型梳状共聚物在准固态染料敏化太阳能电池中的应用及其对电子复合的影响

合成了乙烯基咪唑碘盐(VImI)和聚乙二醇单甲醚甲基丙烯酸酯(PEGMA)的梳状共聚物.利用VImI/PEGMA共聚物制备了准固态聚合物电解质.通过光电流密度-电压(J-V)曲线和电导率测定以及电化学阻抗分析,探讨了基于此电解质的染料敏化太阳能电池的电荷传输与界面电子转移机制.结果表明,VImI/PEGMA共聚物可以有效抑制TiO2/电解质界面电子复合并提高TiO2导带能级,敏化电池的光伏性能并不完全取决于电解质的电导率.通过考察共聚物中VImI与PEGMA单元的摩尔比与开路电压的关系,发现共聚物对电子复合的抑制作用主要源于VImI链段.此外,开路电压衰减(OCVD)和瞬态光电流测试结果说明,共聚物能够提高TiO2薄膜的电子寿命,而且对陷阱电子能级的分布具有调节作用.当共聚物在电解质中的质量分数为50%,VImI与PEGMA的摩尔比为5.0时,准固态染料敏化太阳能电池于100mW·cm-2光强下获得了4.10%的光电转换效率.     

Dependence of solar cell performance on the nature of alkaline counterion in gel polymer electrolytes containing binary iodides

Performance of dye-sensitized nano-crystalline TiO₂ thin film-based photo-electrochemical solar cells (PECSCs) containing gel polymer electrolytes is largely governed by the nature of the cation in the electrolyte. Dependence of the photovoltaic performance in these quasi-solid state PECSCs on the alkaline cation size has already been investigated for single cation iodide salt-based electrolytes. The present study reports the ionic conductivity dependence on the nature of alkaline cations (counterion) in a gel polymer electrolyte based on binary iodides. Polyacrylonitrile-based gel polymer electrolyte series containing binary iodide salts is prepared using one of the alkaline iodides (LiI, NaI, KI, RbI, and CsI) and tetrapropylammonium iodide (Pr₄NI). All the electrolytes based on binary salts have shown conductivity enhancement compared to their single cation counterparts. When combined with Pr₄NI, each of the Li⁺, Na⁺, K⁺, Rb⁺, and Cs⁺ cation containing iodide salts incorporated in the gel electrolytes has shown a room temperature conductivity enhancement of 85.59, 12.03, 12.71, 20.77, and 15.36%, respectively. The conductivities of gel electrolytes containing binary iodide systems with Pr₄NI and KI/RbI/CsI are higher and have shown values of 3.28, 3.43, and 3.23 mS cm⁻¹, respectively at room temperature. The influence of the nature of counterions on the performance of quasi-solid state dye-sensitized solar cells is investigated by assembling two series of cells. All the binary cationic solar cells have shown more or less enhancements of open circuit voltage, short circuit current density, fill factor, and efficiency compared to their single cation counterparts. This work highlights the importance of employing binary cations (a large and a small) in electrolytes intended for quasi-solid state solar cells. The percentage of energy conversion efficiency enhancement shown for the PECSCs made with electrolytes containing Pr₄NI along with Li⁺, Na⁺, K⁺, Rb⁺, and Cs⁺ iodides is 260.27, 133.65, 65.27, 25.32, and 8.36%, respectively. The highest efficiency of 4.93% is shown by the solar cell containing KI and Pr₄NI. However, the highest enhancements of ionic conductivity as well as the energy conversion efficiency were exhibited by the PECSC made with Li⁺-containing binary cationic electrolyte.

     

A 7.72% efficient dye sensitized solar cell based on novel necklace-like polymer gel electrolyte containing latent chemically cross-linked gel electrolyte precursors

Novel necklace-like polymer gel electrolytes containing latent chemically cross-linked gel electrolyte precursors were prepared for quasi-solid dye sensitized solar cells with a highest efficiency of 7.72% and an active area of 0.25 cm2 under AM1.5 condition at 100 mW cm(-2) irradiation.     

P(VDF-HFP)基凝胶电解质染料敏化纳米TiO2薄膜太阳电池

采用循环伏安法(CV)研究了凝胶电解质中I₃-/I-氧化还原行为,凝胶电解质中I₃-/I-的表观扩散系数和相应的稳态扩散电流明显低于液体电解质.通过对阴/阳离子的结合能和孔穴阻塞作用的研究解释了凝胶电解质电导率较液体电解质发生变化的原因.制备的凝胶电解质电池具有较高的光电转换效率(6.6%),其短路电流密度(Jsc)仅比液体电解质电池低0.3-0.4 mA/cm²,电池效率也仅低约0.6%.     

染料敏化太阳电池电解质

染料敏化太阳电池是新一代的太阳电池,有着巨大的应用前景。其中电解质体系是电池组成的主要部分,对电池的性能有着重要的影响。本文介绍了染料敏化太阳电池的基本原理,详细评述了近几年国内外学者对染料敏化太阳电池用电解质体系的研究进展情况,根据电解质的存在状态将其分为液态、准固态和固态三大类并逐一进行介绍,最后对该领域的前景进行了展望。