TiO2柱层状HTiNbO5的合成及在环己酮肟气相Beckmann重排反应中的催化性能

钛酸异丙酯(TIP)、CH₃COOH和H₂O按体积比1∶16∶40混合后得到Ti(Ⅳ)多聚阳离子柱化液, 与正癸胺插层钛铌酸盐进行交换反应后制得钛(Ⅳ)多聚阳离子插层钛铌酸盐, 其层间距为1.70 nm. 在空气气氛中于623 K焙烧处理后, 所得产品能保持良好的层柱结构. 在空气气氛中于723 K焙烧后所得的TiO₂柱层状钛铌酸(TiO₂-HTiNbO₅), 其层间距为0.97 nm, 比表面积为89 m²/g. 以TiO₂-HTiNbO₅为载体, 用浸渍法制备了一系列B₂O₃负载量不同的负载型样品B₂O₃/TiO₂-HTiNbO₅, 考察了它们在环己酮肟气相Beckmann重排反应中的催化性能并测试了它们的红外光谱. B₂O₃/TiO₂-HTiNbO₅的催化性能优于TiO₂-HTiNbO₅. 在B₂O₃负载质量分数为7.31%的催化剂上, 环己酮肟转化率接近100%且在4.5 h内无明显改变, 己内酰胺选择性接近90%. 红外光谱分析结果表明, 当B₂O₃负载量很低时, 硼组分高度分散于载体TiO₂-HTiNbO₅表面, 并主要以BO₄结构形式存在; 当B₂O₃负载质量分数高于7.31%时, BO₃结构形式在数量上占优势. 将催化性能与红外光谱结果关联后可知, 对于负载型样品B₂O₃/TiO₂-HTiNbO₅, 表面的BO₃和BO₄两种结构形式在环己酮肟气相Beckmann重排反应中具有协同促进作用.     

纳米TiO2/碳化树脂复合催化剂的合成及其光催化性能研究

利用一种简单、快速的方法合成了纳米TiO₂/碳化树脂(B)复合催化剂,对其组成、结构、尺寸及其光催化性能进行了表征.结果表明,该复合材料为由碳、氢、氧和钛等4种元素组成的纳米材料,尺寸约30nm,其中Ti和O的堆积结构为锐钛矿型;在该复合材料中,B为具有活性基团和不同长度碳-碳共轭链的大分子,且与TiO₂之间存在着某种化学作用,复合材料所具有的特殊电子结构不仅使其能吸收紫外-可见区的全程光波,而且对光生电荷具有很高的分离能力,从而表现出较高的光催化活性.     

TiO2／Al2O3负载量对气相酯交换合成碳酸甲丙酯的影响

采用XRD、N2 physical adsorption、XPS、NH3-TPD和吡啶吸附IR等技术,对碳酸二甲酯和丙醇气固相合成碳酸甲丙酯的TiO2/Al2O3催化剂进行了表征.实验结果表明,TiO2/Al2O3表面的Lewis酸中心是反应的催化活性位,酸性主要来源于Al2O3,TiO2起修饰作用,有利于选择性生成碳酸甲丙酯.随着Ti负载量的增加,TiO2在Al2O3表面由高度分散状态向晶态转变,其比表面积逐渐降低,但是TiO2/Al2O3的表面酸性质没有受到显著影响,L酸量先是增加,而后略有下降.当Ti负载量为5%时,DMC的转化率及MPC的选择性分别达到54.3%和88.1%.     

Synthesis of Nanocrystalline Materials Based on the Bi2O3-TiO2 System

Russian Journal of General Chemistry - Nanocrystalline bismuth titanates Bi2Ti4O11 (115±5 nm), Bi4Ti3O12 (60±5 nm), Bi2Ti2O7 (105±5 nm), Bi8TiO14 (82±5 nm), and Bi12TiO20...     

H2O和SO2对Ce(1)Mn(3)Ti催化剂催化氧化NO性能的影响

为了提高MNO_x/TiO₂催化剂催化氧化NO的活性,在载体TiO₂上负载醋酸锰的同时掺杂了一定量的硝酸铈,构成了Ce(1)Mn(3)Ti催化剂,并对催化剂进行XRD、BET和XPS等表征。重点考察了H₂O和SO₂对催化剂活性的影响,通过FT-IR、SEM和BET等表征手段对毒化前后的催化剂组成及结构进行了分析。结果表明,Ce(1)Mn(3)Ti催化剂具有较好的活性,在空速41 000 h^-1、NO体积分数为300×10^-6及O₂含量10%的条件下,反应温度200℃时NO转化率可达58%,250℃时NO转化率达到最高值85%。单独加入4%H₂O使得催化剂活性降低,升高反应温度,H₂O对催化剂的影响减弱;同时通入4%H₂O和100×10^-6SO₂,在反应温度250℃时,NO转化率下降并维持在48%左右,停止通入后恢复到61%。H₂O和SO₂使催化剂活性物种硫酸盐化失活。     

SO2 on TiO2(110) and Ti2O3(102) nonpolar surfaces: a DFT study

Density functional molecular cluster calculations have been used to investigate the interaction of SO(2) with defect-free TiO(2)(110) and Ti(2)O(3)(102) surfaces. Adsorbate geometries and chemisorption enthalpies have been computed and discussed. Several local minima have been found for TiO(2)(110), but only one seems to be relevant for the catalytic conversion of SO(2) to S. In agreement with experiment, the bonding of SO(2) to Ti(2)O(3)(102) is much stronger than that on TiO(2)(110). Moreover, our results are consistent with the surface oxidation and the formation of strong Ti-O and Ti-S bonds. On both substrates, the bonding is characterized by a two-way electron flow involving a donation from the SO(2) HOMO into virtual orbitals of surface Lewis acid sites (), assisted by a back-donation from surface states into the SO(2) LUMO. However, the localization of surface states and the strength of back-donation are very different on the two surfaces. On TiO(2)(110), back-donation is weaker, and it involves unsaturated bridging O atoms, while on Ti(2)O(3)(102), it implies the -based valence band maximum and significantly weakens the S-O bond.     

V2O5/TiO2-ZrO2催化剂上甲醇选择氧化制甲缩醛

采用共沉淀法制备TiO2-ZrO2复合氧化物载体、等体积浸渍法制备V2O5/TiO2-ZrO2催化剂,对催化剂在温和条件下甲醇选择氧化生成甲缩醛(DMM)反应进行研究.结果表明,与单一氧化物载体TiO2或ZrO2负载的钒基催化剂相比,V2O5/TiO2-ZrO2对甲醇选择氧化具有较好的催化性能.XRD、NH3-TPD和...     

First-principles thermochemistry for the production of TiO2 from TiCl4

Despite the industrial importance of the process, the detailed chemistry of the high-temperature oxidation of titanium tetrachloride (TiCl4) to produce titania (TiO2) nanoparticles remains unknown, partly due to a lack of thermochemical data. This work presents the thermochemistry of many of the intermediates in the early stages of the mechanism, computed using quantum chemistry. The enthalpies of formation and thermochemical data for TiOCl, TiOCl2, TiOCl3, TiO2Cl2, TiO2Cl3, Ti2O2Cl3, Ti2O2Cl4, Ti2O3Cl2, Ti2O3Cl3, Ti3O4Cl4, and Ti5O6Cl8 were calculated using density functional theory (DFT). The use of isodesmic and isogyric reactions was shown to be important for determining standard enthlapy of formation (Delta(f)H(degree)(298K)) values for these transition metal oxychloride species. TiOCl2, of particular importance in this mechanism, was also studied with CCSD(T) and found to have Delta(f)H(degree)(298K) = -598 +/- 20 kJ/mol. Finally, equilibrium calculations were performed to identify which intermediates are likely to be most prevalent in the high temperature industrial process, and as a first attempt to identify the size of the critical nucleus.     

Selective catalytic oxidation of NO with O2 over Ce-doped MnOx/TiO2 catalysts

A series of Ce-doped MnOx/TiO2 catalysts were prepared by impregnation method and used for catalytic oxidation of NO in the presence of excess O2. The sample with the Ce doping concentration of Ce/Mn=1/3 and calcined at 300°C shows a superior activity for NO oxidation to NO2. On Ce(1)Mn(3)Ti catalyst, 58% NO conversion was obtained at 200°C and 85% NO conversion at 250°C with a GHSV of 41000 h-1, which was much higher than that over MnOx/TiO2 catalyst (48% at 250°C). Characterization results implied that the higher activity of Ce(1)Mn(3)Ti could be attributed to the enrichment of well-dispersed MnOx on the surface and the abundance of Mn3+ and Ti3+ species. The addition of Ce into MnOx/TiO2 could improve oxygen storage capacity and facilitate oxygen mobility of the catalyst as shown by PL and ESR, so that its activity for NO oxidation could be enhanced. The effect of H2O and SO2 on the catalyst activity was also investigated.     

Deposition of a thin film of TiOx from a titanium metal target as novel blocking layers at conducting glass/TiO2 interfaces in ionic liquid mesoscopic TiO2 dye-sensitized solar cells

In dye-sensitized TiO2 solar cells, charge recombination processes at interfaces between fluorine-doped tin oxide (FTO), TiO2, dye, and electrolyte play an important role in limiting the photon-to-electron conversion efficiency. From this point of view, a high work function material such as titanium deposited by sputtering on FTO has been investigated as an effective blocking layer for preventing electron leakage from FTO without influencing electron injection. X-ray photoelectron spectroscopy analysis indicates that different species of Ti (Ti4+, Ti3+, Ti2+, and a small amount of Ti0) exist on FTO. Electrochemical and photoelectrochemical measurements reveal that thin films of titanium species, expressed as TiOx, work as a compact blocking layer between FTO and TiO2 nanocrystaline film, improving Voc and the fill factor, finally giving a better conversion efficiency for dye-sensitized TiO2 solar cells with ionic liquid electrolytes.     

Effect of calcination temperature on structure and performance of Ni/TiO2-SiO2 catalyst for CO2 reforming of methane

The influence of calcination temperature on the structure and catalytic behavior of Ni/TiO2-SiO2 catalyst, for CO2 reforming of methane to synthesis gas under atmospheric pressure, was investigated. The results showed that the Ni/TiO2-SiO2 catalyst calcined at 700 ℃ had high and stable activity while the catalysts calcined at 550 and 850 ℃ had low and unstable activity. Depending on the calcination temperature, one, two, or three of the following Ni-containing species, NiO, Ni2.44Ti0.72Si0.07O4, and NiTiO3 were identified by combining the temperature programmed reduction （TPR） and X-ray diffraction （XRD） results. Their reducibility decreased in the sequence： NiO〉Ni2.44Ti0.72Si0.07O4〉NiTiO3. It suggests that high and stable activities observed over the Ni/TiO2-SiO2 catalyst calcined at 700 ~C were induced by the formation of Ni2.44Ti0.72Si0.07O4 and smaller NiO species crystallite size.     

Time—resolved Microwave Conductivity Studies on the Chemical Treatment of the Nanocrystalline Porous TiO2 Films

Effect of Ti(iso-C3H7O)4 treatment on the photoinduced charge carrier kinetics of nanocrystalline porous TiO2 films is studied by time-resolved microwave conductivity measurements. Analysis of the transient photoconductivity decays indicates that Ti(iso-C3H7O)4 treatment leads to an increased concentration of photogenerated charge carriers and a fast interfacial transfer rate of holes via the surface modification of the fleshly growing TiO2 nanocrystallites.     

纳米TiO2膜修饰电极上对硝基苯甲酸异相电催化还原

有机电合成具有对环境友好、反应条件温和副产物少等优点并符合“原子经济性”要求，是一种可持续发展的绿色化学方法，已成为化学研究的重要前沿之一．使用媒质作为氧化剂和还原剂的间接电合成，大多为均相氧化还原电催化过程，把氧化还原催化剂固定在电极表面的异相电催化与均相催化相比具有更为显著的优点．本文采用循环伏安和电解合成法研究了纳米TiO2膜电极在硫酸介质和氢氧化钠介质中的氧化还原行为以及异相电催化还原对硝基苯甲酸的活性，探讨了纳米TiO2膜异相电催化的本质．     

Hierarchical TiO(2) flowers built from TiO(2) nanotubes for efficient Pt-free based flexible dye-sensitized solar cells

A novel hierarchical TiO(2) flower consisting of anatase TiO(2) nanotubes on a Ti foil substrate has been prepared via a mild hydrothermal reaction of TiO(2) nanoparticles/Ti foil. The photovoltaic performance of DSSC based on hierarchical TiO(2) flowers/Ti (7.2%) is much higher than that of TiO(2) nanoparticle/Ti (6.63%) because of its superior light scattering ability and fast electron transport. Moreover, full flexible DSSC based on the novel hierarchical TiO(2) flowers/Ti foil photoelectrode and electrodeposited poly(3,4-ethylenedioxythiophene) (PEDOT) on indium tin oxide-coated poly(ethylene terephthalate) (ITO-PET) counter electrode shows a significant power conversion efficiency of 6.26%, accompanying a short-circuit current density of 11.96 mA cm(-2), an open-circuit voltage of 761 mV and a fill factor of 0.69.     

不同基材上TiO2膜的表征和光催化活性评价

 采用溶胶-凝胶法在平行条件下制备了负载于钛、铝、不锈钢和玻璃等不同基材上的TiO2浸渍提拉膜,利用原子力显微镜、俄歇电子能谱、X射线衍射、漫反射紫外-可见光谱和苯甲酰胺光催化降解等手段对TiO2膜进行了表征和催化活性评价. 实验结果表明,基材的种类对TiO2膜的性能有较大影响,各膜样品虽均为锐钛矿晶型,但表面形貌显著不同. TiO2/Ti, TiO2/steel, TiO2/Al和TiO2/glass上TiO2的平均粒径分别是152, 205, 241和477 nm,且前两者的粒径分布较为集中. TiO2/Ti和TiO2/Al样品表面仅有Ti和O元素存在,而TiO2/steel和TiO2/glass表面则分别检测到有Fe和Na,Ca及Si等基材元素渗出. 各膜样品对苯甲酰胺光催化降解的活性次序是:TiO2/Ti＞TiO2/Al＞TiO2/glass＞TiO2/steel. 根据实验结果可以推测,在焙烧阶段各基材上前驱体膜烧结行为的不同以及基材元素的渗出是造成不同基材上的TiO2膜在表面形貌、化学组成、光吸收性能以及光催化活性方面存在明显差异的主要原因.     

丙烯在Au/TiO2催化剂上的化学吸附与临氢环氧化反应

环氧丙烷;丙烯环氧化;丙烯在Au/TiO2催化剂上的化学吸附与临氢环氧化反应     

TiO2与ZnO复合纳米结构电极的光电化学研究

利用尿素加压共沉淀法以Ti(SO4)2与Zn(NO3)2为原料制备了TiO2-ZnO复合纳米粒子, 其纳米结构电极的光电化学研究结果表明, 反应物摩尔比为3∶1, 于530 ℃煅烧制备的复合纳米结构电极的光电转换效率最高. 对吸附染料RuL2(SCN)2∶2TBA的纳米结构TiO2和各种复合纳米粒子的纳米结构电极进行光电研究的结果表明, 染料对各纳米结构电极都起到了敏化作用, 其中也是由反应物摩尔比为3∶1, 于530 ℃煅烧制备的纳米结构电极的光电转换效率最高. 对聚3-甲基噻吩修饰的纳米结构TiO2和摩尔比为3∶1, 于530 ℃煅烧的复合纳米粒子构成的纳米结构电极进行光电性能研究, 结果表明, 聚3-甲基噻吩与半导体纳米粒子之间存在p-n结, 在一定条件下p-n结的存在有利于光生电子/空穴的分离, 从而提高了光电转化效率.     

Effects of Carrier on CuO／TiO2 and CuO／Ti0.5Zr0.5O2 Catalysts in the NO＋CO Reaction

Using TiO2 and Ti0.5Zr0.5O2 as carriers, the CuO/TiO2 and CuO/Ti0.5Zr0.5O2 catalysts were prepared by the impregnation method with Cu(NO3)2 as active component. The catalytic activities in NO CO reaction were investigated using a microreactor-GC system, and structure and reducibility of catalysts were characterized by means of physical adsorption, TPR, XRD, NO-TPD technologies. It was found that the activity of CuO/Ti0.5Zr0.5O2 catalyst was higher than that of CuO/TiO2, probably due to the large specific surface area of Ti0.5Zr0.5O2 that played an important role in NO CO reaction.     

Synthetic architectures of TiO2/H2Ti5O11.H2O, ZnO/H2Ti5O11.H2O, ZnO/TiO2/H2Ti5O11.H2O, and ZnO/TiO2 nanocomposites

Although synthetic investigations of inorganic nanomaterials had been carried out extensively over the past decade, few of them have been devoted to fabrication of complex nanostructures that comprise multicomponents/phases (i.e., composite nanobuilding blocks), especially in the area of structural/morphological architecture. In this work, nanobelts of a protonated pentatitanate (H(2)Ti(5)O(11).H(2)O) were synthesized hydrothermally for the first time. Two technologically important transition-metal-oxides TiO(2) and ZnO were then grown respectively or sequentially onto the surface of the as-prepared nanobelts in aqueous mediums. With a main emphasis on organizational manipulation, the present investigation examines general issues of morphological complexity, synthetic interconvertibility, and material combinability related to fabrication of inorganic nanocomposites. Using this model material system, we demonstrate that complex binary and tertiary composite building blocks of TiO(2)/H(2)Ti(5)O(11).H(2)O, ZnO/H(2)Ti(5)O(11).H(2)O, ZnO/TiO(2)/H(2)Ti(5)O(11).H(2)O, and ZnO/TiO(2) can be architected stepwise in solution. Structural features of these nanocomposites have also been addressed.     

Comparison of electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb, Ge, Zr-added TiO2 composite electrodes

Electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were examined to disclose the effects of partial substitution of Ti atom by the other metals in the composite electrodes. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were prepared by sol-gel process using laurylamine hydrochloride as a template for the formation of micellar precursors yielding well-defined mesoporous nanocrystalline structures, as in the cases of the formation of silica and titania tubules and nanoparticles by the templating mechanism. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were characterized by transmission electron microscopy, BET surface area analysis, X-ray diffraction analysis, Raman spectroscopy, and impedance measurements. The TiO2 anatase nanocrystalline structure is retained after doping a small amount (5 mol %) of Nb, Ge, or Zr into the TiO2 structure, suggesting the homogeneous distribution of the doped metals with replacing Ti atom by the doped metal. The power conversion efficiency of the porphyrin-sensitized solar cells increases in the order Zr-added TiO2 (0.8%) < Nb-added TiO2 (1.2%) < TiO2 (2.0%) < Ge-added TiO2 cells (2.4%) under the same conditions. The improvement of cell performance of the Ge-added TiO2 cell results from the negative shift of the conduction band of the Ge-added TiO2 electrode. The Ge-added TiO2 cell exhibited a maximum power conversion efficiency of 3.5% when the porphyrin was adsorbed onto the surface of the Ge-added TiO2 electrode with a thickness of 4 microm in MeOH for 1 h.