Observation of a Quadrupole Surface Plasmon Mode for Au Nanorods: Effects of Surface Roughness and Crystal Facets

This paper describes how the surface roughness and synthetic methods of Au nanorods affect the optical properties that are often associated with localized surface plasmon resonances. We synthesized Au nanorods with different aspect ratios and surface roughness by using two different synthetic strategies to observe surface plasmon resonance bands. One set of nanorods was prepared in high yield by using a seed‐mediated dropwise‐addition method with a growth‐directing surfactant in aqueous solution (Au nanorods in aqueous phase, GNRA). The other set of Au nanorods were synthesized by the electrochemical deposition of Au onto an anodized aluminum oxide (AAO) template (Au nanorods by AAO template, GNRT). The length of the nanorods was controlled by changing the total charge that was passed through the cell and their diameter was monitored by changing the diameter of the template channel. The as‐prepared Au nanorods were optimized to observe a quadrupole mode, which is one of the higher‐order surface plasmon bands. Our results showed differences between the optical properties of GNRA and GNRT. The roughness and crystal structure of the Au nanorods affected their optical properties. Smooth and single‐crystal surface on GNRA had larger and sharper peaks than GNRT. The discrete dipole approximation (DDA) method was used to calculate the optical properties of the Au nanorods and these results were in good agreement with our experimental results.     

Surface-functionalized CdSe nanorods for assembly in diblock copolymer templates

Poly(ethylene oxide)-covered CdSe nanorods were prepared and assembled in diblock copolymer templates by floating the block copolymer templates onto aqueous nanorod solutions. The assembly was enabled by consideration of the surface ligand coverage of the nanorods. Alkane-covered CdSe nanorods prepared by state-of-the-art techniques are not compatible with this assembly process. However, poly(ethylene oxide) (PEO)-functionalized CdSe nanorods were successfully used to assemble the nanorods into the channels and pores of diblock copolymer templates. Other water-dispersible CdSe nanorods, such as those covered with 11-mercaptoundecanoic acid (MUA), did not give the desired assemblies. These results are understood by considering the surface energies of the PEO-covered CdSe nanorods in this interfacial assembly process.     

Surface study of sintered alumina substrates using solution‐processed ZnO nanorods as a microscopic wettability indicator

Wettability and its distribution are crucial factors that indicate the surface conditions of substrates. We report a surface study of sintered alumina substrates using solution‐processed ZnO nanorods as a microscopic wettability indicator. The alumina substrates comprising of micrometer‐sized sintered grains were treated separately with ultraviolet/ozone (dry process) or ozone water (wet process), and their surface conditions were characterized by conventional surface analysis methods, such as water contact angle, X‐ray photoelectron spectroscopy and grazing angle attenuated total reflection Fourier transform infrared spectroscopy. The results showed that the alumina substrates treated with ultraviolet/ozone and ozone water had distinct clean surfaces compared to those without treatments, but no significant differences were noted between these two ozone‐based treatments. Then, as a wettability‐sensitive deposition technique, Pd‐catalyzed chemical deposition of ZnO nanorods was performed on the alumina substrates, which involved dip coating of Pd nanoparticles on the substrates in aqueous solutions, followed by the chemical solution growth of ZnO. Vertically aligned ZnO nanorods of ~85 nm in diameter were densely formed along a rough surface of the substrates. Morphological uniformity of the nanorods varied depending on the treatment condition; local surfaces with sufficient wettability provided uniform nanorods but those with insufficient wettability gave irregular nanorods, making the visualization of the microscopic surface wettability possible. Copyright © 2016 John Wiley & Sons, Ltd.     

Immobilization of gold nanorods onto acid-terminated self-assembled monolayers via electrostatic interactions

We report the immobilization of gold nanorods onto self-assembled monolayers (SAMs) of 16-mercaptohexadecanoic acid (16-MHA). The simple two step protocol involves formation of a SAM of 16-MHA molecules onto gold-coated glass slides and subsequent immersion of these slides into the gold nanorod solution. The nanorods, formed by a seed-mediated, surfactant-assisted synthesis protocol, are stabilized in solution due to surface modification by the surfactant cetyltrimethylammonium bromide (CTAB). Attractive electrostatic interactions between the carboxylic acid group on the SAM and the positively charged CTAB molecules are likely responsible for the nanorod immobilization. UV-vis spectroscopy has been used to follow the kinetics of the nanorod immobilization. The nature of interaction between the gold nanorods and the 16-MHA SAM has been probed by Fourier transform infrared spectroscopy (FTIR). The surface morphology of the immobilized rods is studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurements. SEM was also used to determine the density of the immobilized nanorods as a function of the pH of immobilization. Control over the surface coverage of the immobilized gold nanorods has been demonstrated by simple pH variation. Such well-dispersed immobilized gold nanorods with control over the surface coverage could be interesting substrates for applications such as surface-enhanced Raman spectroscopy (SERS).     

Ultrafast spectroscopy and coherent acoustic phonons of Au-Ag core-shell nanorods

We performed the first investigations of coherent acoustic phonons in Au-Ag core-shell nanorods, which were compared with the results of parental Au nanorods. Both breathing and extensional modes were observed in Au-Ag core-shell nanorods with ~11 nm Ag shell while only extensional modes were detected in other core-shell nanorods with 4-7 nm Ag shell. Young's modulus estimated from the oscillation period of extensional modes was found to be larger for Au-Ag core-shell nanorods with ~4 nm Ag shell, as compared with that of Au nanorods. The value of Young's modulus decreases with the increase of the Ag shell thickness and finally becomes smaller than that of Au nanorods. This phenomenon is interpreted in terms of the surface effects and the existence of grain boundaries in the lattice structure of Ag shell.     

局域表面等离子体共振辅助的金纳米棒/聚合物纳米复合材料的双光子聚合

本文研究了金纳米棒的局域表面等离子体共振效应在双光子聚合过程中的作用,即当激发光与金纳米棒表面等离子体共振波长相匹配时,会在金纳米棒表面产生很强的局域电磁场,从而引发双光子聚合。通过采用与金纳米棒表面等离子体共振波长相同的飞秒激光,在低于光刻胶聚合阈值的功率下照射含有金纳米棒的光刻胶,制备聚合物包覆金纳米棒的纳米复合材料。透射电子显微镜结果表明,当飞秒激光功率为0.6 W、光斑直径为1.6 cm、照射时间为0.3 s时,金纳米棒表面成功聚合上厚度为5 nm左右的聚合物。本研究在制备聚合物/金属纳米粒子方面提供了一种简单可行的方法,有望在纳米光子学、纳米传感器等新兴领域得到应用。     

Some Aspects of Seedless Synthesis of Gold Nanorods

Seedless synthesis of gold nanorods with the use of sodium borohydride and hydroquinone as reductants of metal ions has been systematically studied. The effect of reaction system composition on the morphology and optical characteristics of the formed particles has been determined. It has been found that the position of the band of the longitudinal surface plasmon resonance of the nanorods varies nonmonotonically with variations in the concentration of hydroquinone or silver nitrate. The seedless synthesis has been shown to yield high-quality gold nanorods, with the tunable position of their longitudinal surface plasmon resonance in a wide spectral range (from 700 to ~1050 nm). Therewith, the conversion of metal ions is no lower than 78 wt %.     

Facile synthesis and characterization of functionalized, monocrystalline rutile TiO2 nanorods

Functionalized, monocrystalline rutile TiO2 nanorods were prepared from TiCl4 in aqueous solution under acidic conditions in the presence of dopamine, followed by aging and hydrothermal treatment at 150 degrees C. The surface-bound organic ligand controls the morphology as well as the crystallinity and the phase selection of TiO2. The presence of monocrystalline rutile TiO2 was confirmed by X-ray powder diffraction and HRTEM investigations. The as-prepared nanorods are soluble in water at pH <3. The surface functionalization was analyzed by IR and 1H NMR, confirming the presence of dopamine on the surface. The surface amine groups can be tailored further with functional molecules such as dyes. Confocal laser scanning microscopy (CLSM) was used to characterize the binding of the fluorescent dye 4-chloro-7-nitrobenzofurazan (NBD) to the functionalized surface of the TiO2 nanorods.     

Nanorod Aspect Ratios Determined by the Nano‐Impact Technique

The in situ electrochemical sizing of individual gold nanorods is reported. Through the combination of electrochemical dissolution and the use of a surface‐bound redox tag, the volume and surface area of the nanorods are measured, and provide the aspect ratio and the size of the nanorods. Excellent independent agreement is found with electron microscopy analysis of the nanorods, establishing the application of nano‐impact experiments for the sizing of anisotropic nanomaterials.     

Biotin-streptavidin-induced aggregation of gold nanorods: tuning rod-rod orientation

We report herein biotin-streptavidin-mediated aggregation studies of long gold nanorods. We have previously demonstrated end-to-end linkages of gold nanorods driven by the biotin-streptavidin interaction (Caswell et al. J. Am. Chem. Soc. 2003, 125, 13914). In that report, the specific binding of biotin disulfide to the gold nanorod edges was achieved due to the preferred binding of thiol molecules to the Au[111] surface (gold nanorod ends) as opposed to the gold nanorod side faces. This led to the end-end linkage of gold nanorods upon subsequent addition of streptavidin. In this report we demonstrate a simple procedure to biotinylate the entire gold nanorod surface and subsequently form a 3-D assembly by addition of streptavidin. Gold nanorods were synthesized by the three-step seeding protocol documented in our previous articles. The surface of gold nanorods was further modified by a layer of a weak polyelectrolyte, poly(acrylic acid), PAA. A biotin molecule which has an amine group at one end (biotin-PEO-amine) was anchored to the carboxylic acid group of the polyelectrolyte using the well-known carbodiimide chemistry. This process biotinylates the entire gold nanorod surface. Addition of streptavidin further leads to aggregation of gold nanorods. A closer look at the aggregates reveals a preferential side-to-side assembly of gold nanorods. The gold nanorods were characterized at each stage by UV-vis spectroscopy, light scattering, and transmission electron microscopy (TEM) measurements.     

Surface tension and fluid flow driven self-assembly of ordered ZnO nanorod films for high-performance field effect transistors

Colloidal nanorods of inorganic semiconductors are of interest for a range of optoelectronic devices. The ability to self-assemble these materials into ordered arrays by solution-processing techniques is crucial for achieving adequate device performance. Here we show that uniform ZnO nanorod films with defined nanorod alignment can be solution-deposited over large areas by controlling the surface energy of the nanorods through the choice of suitable ligands and by the fluid flow direction during growth. ZnO nanorods with long carbon chain ligands exhibit a smaller surface free energy than those with short carbon chain ligands resulting in better in-plane alignment and large domain sizes up to dozens of micrometers in spin-coated films. A model is presented to rationalize the observed self-assembly behavior. It is based on the formation of a lyotropic liquid crystalline phase on the surface of the liquid film which is facilitated by enhanced segregation of nanorods with low surface tension to the surface. Alignment of the nanorods is controlled by radial and vertical liquid flows in the drying solution. The ability to control the orientation of the nanorods and to achieve large domain size results in significant device performance improvement. Field-effect transistors with mobilities of up to 1.2-1.4 cm2/V.s are demonstrated in spin-coated, in-plane aligned ZnO nanorod films subject to postdeposition hydrothermal growth.     

Spontaneous self-assembly of cerium oxide nanoparticles to nanorods through supraaggregate formation

Self-assembly of cerium oxide nanoparticles to nanorods is reported. Such nanorods have an aspect ratio of 6 with a diameter of approximately 40 nm. The formation of cylindrical supraaggregates and their subsequent growth by preferential assembling of ceria nanocrystallites along the longitudinal direction was proposed to be the probable mechanism of spontaneous self-assembly of nanorods. The supraaggregate formation was facilitated by influencing the local curvature of the micelle surface in the presence of nitrate ions as a precursor solution. The nanorods were characterized using high-resolution transmission electron microscopy with energy dispersive spectroscopy and selected area electron diffraction for their morphology, chemistry, and crystal structure.     

Silica-coated Au/Ag nanorods with tunable surface plasmon bands for nanoplasmonics with single particles

We present the synthesis and analysis of silica-coated Au/Ag bimetallic nanorods with controlled surface plasmon bands. Depending on the thickness of Ag shell deposited on the Au nanorod surface, there is a blue-shift on the longitudinal surface plasmon band of Au nanorods, which can be expressed by an approximate formula derived from the absorption profile of light in Ag films using finite difference time domain simulations. The subsequent coating of silica shell not only enhances the stability of the Au/Ag bimetallic nanorods but also provides a mesoporous host for optically active species. Minute red-shifts of the longitudinal resonance mode, induced by stepwise increased silica shell volumes, are shown. Application as carrier for fluorescent rhodamine B molecules is demonstrated by photoluminescence analysis. On the single-particle level, dark field microscopy of Au/Ag-silica nanorods was finally employed. This introduces a route towards revealing the relation between structure, shape, and optical (plasmonic) properties of complex composite metal particles as well as fabrication strategies for nanoassemblies of tailored structures in the field of nanoplasmonics.     

Praseodymium hydroxide and oxide nanorods and Au/Pr6O11 nanorod catalysts for CO oxidation

Praseodymium hydroxide nanorods were synthesized by a two-step approach: First, metallic praseodymium was used to form praseodymium chloride, which reacted subsequently with KOH solution to produce praseodymium hydroxide. In the second step the hydroxide was treated with a concentrated alkaline solution at 180 degrees C for 45 h, yielding nanorods as shown by the scanning and transmission electron microscopy images. The results of X-ray diffraction and energy-dispersive X-ray spectroscopy experiments indicate that these nanorods are pure praseodymium hydroxide with a hexagonal structure, which can be converted into praseodymium oxide (Pr6O11) nanorods of a face-centered cubic structure after calcination at 600 degrees C for 2 h in air. Gold was loaded on the praseodymium oxide nanorods using HAuCl4 as the gold source, and NaBH4 was used to reduce the gold species to metallic nanoparticles with sizes of 8-12 nm on the nanorod surface. These Au/Pr6O11 nanorods exhibit superior catalytic activity for CO oxidation.     

氨水溶液制备ZnO纳米晶阵列的研究

以氨水和硝酸锌为前躯体，采用低温水溶液法在涂敷ZnO晶种层的玻璃衬底上外延生长了ZnO纳米棒晶阵列。应用SEM、TEM、SAED和XRD表征了ZnO纳米晶的形貌和结构。讨论了该组成体系水溶液法纳米棒外延生长的机理及其对棒晶形貌的影响。通过对水溶液pH值的原位二次调整，制备出了ZnO纳米管和表面绒毛状的棒晶阵列，基于生长机理探讨了它们的形成原因，为实现不同形貌ZnO纳米晶阵列的优化控制提供了可能的技术途径。结果表明，不同形貌的ZnO均属沿c轴择优取向的六方纤锌矿结构。     

Preparation of Gold Nanorods by Electrolysis:Electrochemical Reduction or Chemical Reduction?

In the synthesis of nanosized materials, to control the particle shape is as important as to control its size, because the properties of the nanoparticles strongly depend on both size and shape. The properties of Au nanorods are different from its spherical counterparts in some ways due to the geometric anisotropy. For example, there are two surface plasmon resonance (SP) peaks in the UV-Vis region for Au nanorods, namely, the transverse (SP_t) peak and the longitudinal (SP₁) peak, respectively, while only one for spherical nanoparticles. Recently, Wang et al.^[1,2] proposed an electrolysis-based method to produce Au nanorods with high throughput for the first time, and it was successfully adopted by El-Sayed et al.^[3,4] in their studies on the optical properties and the thermal/laser induced shape transition of gold nanorods. However, the detailed growth mechanism of Au nanorods in such an approach remains untouched at present stage. To this point, only an ambiguous statement is available in Wang's paper^[1,2] as that "the gold nanorods were converted from the bulk anode most likely at the interfacial region of the cathodic surface and within the electrolytic solution",it is still unclear whether the gold nanorods are formed electrochemically or chemically.     

Effects of High Pressure on the Surface Plasmon Resonance of Copper and Silver Nanocrystals

We used a diamond anvil cell(DAC) to control the deformation of synthesized copper nanorods and silver nanoparticles. And we measured the surface plasmon resonance of copper nanorods and silver nanoparticles, which exhibit redshifts or blueshifts. The surface plasmon resonance shows an abnormal blue shift for both copper nanorods and silver nanoparticles. The solvents of copper nanorods and silver nanoparticles are n-hexane and water, where the pressure loads include quasi-hydrostatic and non-hydrostatic.     

电解法制备棒状金纳米粒子溶胶

纳米材料的光学、磁学和电学性质依赖于粒子的尺寸和形状 .因此 ,合成过程中实现纳米粒子形貌的控制非常重要 [1,2].金溶胶在紫外-可见-近红外区的光吸收行为主要取决于金纳米粒子内部电子集体运动的等离子共振 ,其频率由粒子的尺寸所决定 .由于棒状金纳米粒子有横截直径与长度两个特征尺寸 .与大小同其横截直径相当的球形粒子相比 ,棒状粒子除了在 520 nm附近的吸收之外 (横截峰 ,SPt),还在长波方向有一个吸收峰 (长轴峰 ,SPl),其位置随"长径比"的增加而显著红移 [3,4].为了深入研究棒状金纳米粒子由尺寸和形状决定的各种特性及其应用 ,W…     

Preparation and optical properties of worm-like gold nanorods

A type of worm-like nanorods was successfully synthesized through conventional gold nanorods reacting with Na2S2O3 or Na2S. The generated worm-like gold nanorods comprise shrunk nanorod cores and enwrapped shells. Therefore, a gold-gold sulfide core-shell structure is formed in the process, distinguishing from their original counterparts. The formation of the gold chalcogenide layers was confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy. Experimental results showed that the thickness of the gold chalcogenide layers is controllable. Since the increase of shell thickness and decrease of gold nanorod core take place simultaneously, it allows one to tune the plasmon resonance of nanorods. Proper adjustment of reaction time, temperature, additives and other experimental conditions will produce worm-like gold nanorods demonstrating desired longitudinal plasmon wavelength (LPW) with narrow size distributions, only limited by properties of starting original gold nanorods. The approach presented herein is capable of selectively changing LPW of the gold nanorods. Additionally, the formed worm-like nanorods possess higher sensitive property in localized surface plasmon resonance than the original nanorods. Their special properties were characterized by spectroscopic methods such as Vis-NIR, fluorescence and resonance light scattering. These features imply that the gold nanorods have potential applications in biomolecular recognition study and biosensor fabrications.     

Platinum‐Coated Porous Gold Nanorods in Methanol Electrooxidation: Dependence of Catalytic Activity on Ligament Size

Here we demonstrate that, in the dealloying process of Au–Ag nanorods, temperature is the key parameter for producing porous Au nanorods with tunable ligament sizes. The vertically aligned Au–Ag alloy nanorods were first synthesized by the electrochemical co‐deposition of Au and Ag onto anodic aluminum oxide (AAO) membrane templates. Porous Au nanorods were then obtained by selectively etching Ag away from the precursor Au–Ag alloy nanorods. Control of the ligament size was achieved by controlling the dealloying temperature. Pt deposited on the porous Au nanorods with smaller ligaments exhibited a higher catalytic activity during methanol electrooxidation than those deposited on nanorods with larger ligaments produced by dealloying at higher temperatures. The strong dependence of the catalytic activity on the ligament size of porous Au is principally due to different amounts of carbon monoxide (CO) generated during methanol electrooxidation. Less CO was generated as the ligament size decreased. This finding is of importance for developing highly efficient cathode materials for carrying out methanol electrooxidation in practical applications in which porous Au with a large surface area is used as a supporting substrate.