Co与Cu掺杂ZnO薄膜的制备与光致发光研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co, Cu单掺杂及Co,Cu共掺杂ZnO薄膜.用金相显微镜观察了Co与Cu掺杂对ZnO薄膜形貌的影响.X射线衍射（XRD）研究揭示所有ZnO薄膜样品都存在（002）择优取向,在Cu单掺的ZnO薄膜中晶粒尺寸最大.对所有样品的室温光致发光测量都观察到较强的蓝光双峰发射和较弱的绿光发射,其中长波长的蓝光峰和绿光峰都能够通过掺杂进行控制.对不同掺杂源的ZnO薄膜发光性能进行了分析,认为蓝光峰来源于电子由导带底到锌空位能级的跃迁及锌填隙到价带顶的跃迁,绿光峰是由于掺杂造成的 关键词： ZnO薄膜 溶胶-凝胶 Co Cu掺杂 光致发光     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

蓝光ZnO薄膜的特性研究

采用反应溅射法在n型硅（100）衬底上制备了ZnO薄膜,分别用X射线衍射仪、原子力显微镜和荧光分光光度计对样品的结构、表面形貌和光致发光特性进行了表征。X射线衍射结果表明,实验中制备出了应变小的c轴择优取向的ZnO薄膜;原子力显微镜观察表明,薄膜表面平整,颗粒大小约为50nm,为柱状结构,颗粒垂直于硅衬底表面生长;在室温光致发光（PL）谱中观察到了波长位于434nm处的较窄的强蓝光发射峰,该蓝光峰的半峰全宽约为50meV。对蓝光峰的发光机制进行了讨论,并推断出该蓝光峰来源于电子从Zn填隙缺陷能级向价带顶跃迁。     

石英衬底上Au缓冲层对ZnO薄膜微结构的影响

采用单源化学气相沉积(SSCVD)法,在石英衬底上以Au为缓冲层,Zn4(OH)2(O2CCH3)6.2H2O为固相源制备ZnO薄膜。SEM和XRD测试ZnO薄膜的微结构,结果表明:相对于SiO2衬底上生长的ZnO薄膜,Au/SiO2衬底上生长的ZnO薄膜具有较好的结晶质量和表面平整度;对制备ZnO薄膜的衬底温度进行了工艺优化,结果表明:500℃时制备的ZnO薄膜颗粒大小均匀,结晶质量较好;通过荧光光谱仪对Au/SiO2衬底上的ZnO薄膜进行光致发光(PL)谱测试,ZnO薄膜在400nm出现紫光发射峰,而没有出现与缺陷相关的深能级发射峰,表明ZnO薄膜具有较好的结晶质量。     

脉冲激光沉积法在多孔铝衬底上生长的ZnO薄膜的结构与光学性质

ZnO是一种性质优良很有前途的紫外光电子器件材料,多孔铝是一种良好的模板型衬底,试图将二者结合起来以制备出一种全新的光电功能材料。制备了三种不同孔径多孔铝衬底,采用脉冲激光沉积法,在真空背景下,在多孔铝衬底上生长了氧化锌薄膜。利用扫描电子显微镜、X射线衍射和光致荧光对样品进行了测试和分析。研究表明:利用不同孔径的多孔铝衬底生长的氧化锌薄膜的结构和光学性质差异很大。样品A的光致发光主要是394nm的紫外发射和498nm的蓝绿光发射;样品B的光致发光主要是417nm的紫光发射和466nm蓝光发射;样品C的光致发光主要是415nm的紫光发射和495nm的蓝绿光发射。由于薄膜是富锌的,随着在空气中氧化的进行,光谱发生变化。利用固体能带理论对光谱进行了全面的分析。     

LiGaO2衬底上ZnO外延膜的结构与光学特性

采用磁控溅射法在(001),(100)及(010)LiGaO2衬底上制备了ZnO薄膜,通过X射线衍射(XRD)、原子力显微镜(AFM)、透过光谱以及光致发光谱(PL)对薄膜的结构、形貌及光学性质进行了表征.结果表明LiGaO2衬底不同晶面上制备的ZnO薄膜具有不同的择优取向,在(001)、(100)及(010)LiGaO2上分别获得了[001]、[1100]及[1120]取向的ZnO薄膜;不同取向的ZnO薄膜表面形貌差异较大;薄膜在可见光波段具有较高的透过率;在ZnO薄膜的光致发光谱中只观察到了位于378 nm的紫外发射峰,而深能级发射几乎观察不到,(1100)取向的薄膜紫外发射峰强度最大,半高宽也最小,薄膜光致发光件质的差异丰要和晶粒尺寸有关.     

氧化锌/硅纳米孔柱阵列的结构和光致发光特性研究

以硅纳米孔柱阵列(Si-NPA)为衬底、用化学气相沉积法制备了具有规则阵列结构特征的ZnO/Si-NPA纳米复合体系，并对其结构和光致发光性质进行了表征. 实验结果显示，组成ZnO/Si-NPA表面阵列的每个柱子均呈现层壳结构. 不同于衬底Si-NPA的红光和蓝光发射，ZnO/Si-NPA在紫外光区和蓝绿光区呈现出两个强的宽发光峰. 分析表明，紫外光发射应归因于ZnO晶体的带边激子跃迁；而蓝绿光发射则来自于ZnO晶体本征缺陷所形成的两类深能级复合中心上载流子的辐射跃迁.     

磁控溅射制备ZnO薄膜的结构及发光特性研究

采用射频反应磁控溅射法在玻璃衬底上制备出具有c轴高择优取向的ZnO薄膜,利用X射线衍射、扫描探针显微镜及荧光分光光度法研究了生长温度对ZnO薄膜微观结构及光致发光特性的影响。结果表明,合适的衬底温度有利于提高ZnO薄膜的结晶质量;在室温下测量样品的光致发光谱(PL),观察到波长位于400 nm左右的紫光、446 nm左右的蓝色发光峰及502 nm左右微弱的绿光峰,随衬底温度升高,样品的PL谱中紫光及蓝光强度逐渐增大,同时,绿光峰的强度也表现出一定程度的增强。经分析得出紫光应是激子发光所致,而锌填隙则是引起蓝光发射的主要原因,502 nm左右的绿光峰应该是氧的深能级缺陷造成的。此外,还测量了样品的吸收谱,并结合样品吸收谱的拟合结果对光致发光机理的分析作了进一步的验证。     

Co,Sn共掺ZnO薄膜结构与光致发光的研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co,Sn掺杂ZnO系列薄膜.通过金相显微镜和X射线衍射(XRD)研究了Co与Sn掺杂对薄膜的表面形貌和微结构的影响.XRD结果表明,所有ZnO薄膜样品都存在(002)择优取向,特别Sn单掺ZnO薄膜的c轴择优取向最为显著,而且晶粒尺寸最大.XPS测试表明样品中Co和Sn的价态分别为2+和4+,证实Co²⁺,Sn⁴⁺进入了ZnO的晶格.室温光致发光谱(PL)显示在所有的样品中都有较强的蓝光双峰发射和较弱的绿光发 关键词： ZnO薄膜 溶胶-凝胶 掺杂 光致发光     

不同衬底上的ZnO薄膜紫外光致发光

用射频磁控溅射法在蓝宝石、硅和石英衬底上沉积出具有好的择优取向的多晶ZnO薄膜. 在270 nm波长的光激发下室温下可观察到显著的紫外光发射（波长为356 nm）和较弱的蓝光发射（波长为446 nm）. 经高温退火后薄膜的结晶质量显著提高, 在蓝宝石、石英衬底上沉积的薄膜，其积分发光强度分别增加了7倍和14倍.而硅衬底上的膜发光强度增强不太显著.紫外光发射源于电子的带间跃迁，而蓝光发射是由电子从氧空位浅施主能级到价带顶的跃迁引起的. 关键词： ZnO薄膜 射频磁控溅射 紫外发光 退火     

Cu掺杂Ga2O3薄膜的光学性能

采用射频磁控溅射和N₂气氛退火处理制备了多晶Ga₂O₃薄膜和Cu掺杂Ga₂O₃薄膜.用X射线衍射仪、紫外-可见分光光度计、荧光光谱仪对Ga₂O₃薄膜和Cu掺杂Ga₂O₃薄膜的结构和光学性能进行了表征.结果表明,Cu掺杂后Ga₂O₃薄膜的结晶质量变差,透过率明显降低,吸收率增加,光学带隙减小.本征Ga₂O₃薄膜在紫外、蓝光和绿光出现了发光带,Cu掺杂后紫外和蓝光发射增强,且在475 nm 处出现了一个新的发光峰.     

Controlled visible photoluminescence of ZnO thin films prepared by RF magnetron sputtering

ZnO thin films were prepared by RF magnetron sputtering. The photoluminescence dependence on the growth ambient and annealing temperatures and the atmosphere has been studied. Visible photoluminescence with blue, green, orange, and red emission bands has been demonstrated by controlling the preparation conditions. Complete suppression of the visible emission bands was also realized by annealing the O₂-ambient-grown samples in N₂ atmosphere at higher temperatures, which indicated the preparation of ZnO thin films with high optical quality.     

Structural and optical properties of N-doped β-Ga2O3 films deposited by RF magnetron sputtering

The N-doped β-Ga₂O₃ ?lms were grown on Si and quartz substrates by RF magnetron sputtering in different ammonia partial pressure ratios (from 0% to 30%). The influence of ammonia partial pressure ratios and annealing treatment on the optical and structural properties were studied. The microstructure, optical transmittance, optical absorption and optical energy gap of the N-doped β-Ga₂O₃ films are significantly changed with the increasing of ammonia partial pressure. The green, blue and ultraviolet emission bands are observed and discussed.     

铈掺杂氧化铝薄膜的蓝紫色发光特性

应用中频反应磁控溅射技术制备了Al₂O₃:Ce³⁺的非晶薄膜.X射线光电子谱(XPS)检测显示薄膜中有Ce³⁺生成.这些薄膜的光致发光峰是在374nm附近,它来自于Ce³⁺离子的5d¹激发态向基态4f¹的两个劈裂能级的跃迁.发光强度强烈地依赖于薄膜的掺杂浓度,但发光峰位置不随掺杂浓度而变化.Ce³⁺含量和薄膜的化学成分是通过X射线散 关键词： 光致发光 2O₃')" href="#">Al₂O₃ 薄膜 稀土元素     

Electroluminescence properties of In-doped Zn2SiO4 thin films prepared by sol–gel process

The effect of In doping on the electroluminescence (EL) properties of Zn₂SiO₄:In thin films was investigated. In-doped Zn₂SiO₄ thin films were deposited on BaTiO₃ substrates and their EL properties were characterized in this study. X-ray powder diffraction patterns of In-doped Zn₂SiO₄ powders revealed a single phase of Zn₂SiO₄ for In concentrations up to approximately 1.5 mol%, whereas a secondary phase of In₂O₃ was observed for In concentrations in the range of 2–10 mol%. The maximum luminance of thin film electroluminescent (TFEL) devices varied significantly with the amount of In doping. The highest luminance with blue emission was obtained when 2 mol% In was doped. The blue emission of In-doped Zn₂SiO₄ thin film may be related to the In substitution for Zn. The 2 mol% In-doped Zn₂SiO₄ thin film exhibited blue emission with CIE color coordinates of x=0.208 and y=0.086.     

Cathodoluminescence of yttrium oxide and yttrium and zinc silicate films

We have studied the cathodoluminescent properties of Y₂SiO₅:Ce, Zn₂SiO₄:Ti, Zn₂SiO₄:Mn, Y₂O₃:Eu thin films obtained by high-frequency magnetron sputtering. Based on measurements of the luminescence spectra, we have shown that the films can be used as luminophores with blue emission (Y₂SiO₅:Ce, Zn₂SiO₄:Ti), green emission (Zn₂SiO₄:Mn), and red emission (Y₂O₃:Eu). We have studied the dependences of the luminescence intensity on the energy of the exciting electrons, the electron beam current density, and the exposure time. We hypothesize that the decrease in the luminescence intensity during electron bombardment is connected with formation of new oxide layers as a result of an electron-stimulated surface chemical reaction.     

Zn$lt;sub$gt;1-$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;Mg$lt;sub$gt;$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;O薄膜的光致发光特性研究

采用脉冲激光沉积方法在单晶Si（100）衬底上制备出c轴取向的Zn_1-xMg_xO单晶薄膜,通过荧光光谱仪研究了薄膜的光致发光特性.实验结果表明,Mg含量增加,Zn_1-xMg_xO单晶薄膜的紫外发光峰蓝移,发光峰强度减弱,缺陷发光强度增强.同时发现,由于Mg的掺杂,引入了一些束缚能较大的局域束缚态.对于氧气氛下制备的样品,实验发现紫外峰和绿光带发光峰同时增强,但是R值减小,紫外峰红移.对绿光发光机理研究发现,绿光发光带主要与锌空位、氧间隙（O_i）或锌位氧（O_Zn）等缺陷有关,它是由多个缺陷发光峰组成,各缺陷发光峰强度相对变化导致了绿光发光带的整体移动. 关键词： 1-xMg_xO薄膜')" href="#">Zn_1-xMg_xO薄膜 光致发光 脉冲激光沉积     

Light emission from a-Si:C:O:H films fabricated by C2F6 and O2/C2F6 plasma treating silicone oil liquid

Amorphous Si:C:O:H films were fabricated at low temperature by C₂F₆ and O₂/C₂F₆ plasma treating silicone oil liquid. The a-Si:C:O:H films fabricated by C₂F₆ plasma treatment exhibited white photoluminescence at room temperature, while that by O₂/C₂F₆ plasma treatment exhibited blue photoluminescence. Fourier transformed infrared spectroscopy and Raman spectroscopy studies showed that the sp³ and sp² hybridized carbons, SiC bond, SiO bond and carbon-related defects in a-Si:C:O:H films correlated with photoluminescence. It is suggested that the blue emission at 469 nm was related to the sp³ and sp² hybridized carbons, SiC bond, carbon dangling bonds as well as SiO short chains and small clusters, while the light emitting at 554 nm was related to the carbon-related defects.     

Write-once blue laser recording using silicon doped SbOx thin films prepared by reactive dc-magnetron sputtering

Si:SbO_x films have been deposited by reactive dc-magnetron sputtering from a Sb target with Si chips attached in Ar + O₂ with the relative O₂ content 7%. The as-deposited films contained Sb metal, Sb₂O₃, SiO, Si₂O₃ and SiO₂. The crystallization of Sb was responsible for the changes of optical properties of the films. The results of the blue laser recording test showed that the films had good writing sensitivity for blue laser beam (406.7 nm), and the recording marks were still clear even if the films were deposited in air 60 days, which demonstrated that doping silicon in SbO_x films can improve the stability of SbO_x films. High reflectivity contrast of about 36% was obtained at a writing power 6 mW and writing pulse width 300 ns.     

EFFECT OF ZnFe22O4 DOPING ON THE OPTICAL PROPERTIES OF TiO2 THIN FILMS

Amorphous TiO₂ thin films and ZnFe₂O₄ doped TiO₂ composite films were deposited by radio frequency magnetron sputtering. The effect of ZnFe₂O₄ doping on the optical properties of TiO₂ thin films was reported. Our results show that the absorption edge of TiO₂ thin films and composite films exhibits a blue shift with decreasing annealing temperature. The absorption edge of composite films has moved to visible spectrum range, and a very large red shift occurs in comparison with TiO₂ thin film. An enhanced photoluminescence in ZnFe₂O₄ doped anatase TiO₂ thin film at room temperature.