Selective piezoelectric odor sensors using molecularly imprinted polymers

Molecular imprinting technique has been used to create sensors with a predetermined selectivity for molecules in the gas phase. Piezoelectric quartz crystals coated with a 2-methylisoborneol (MIB) imprinted polymer gave responses which were consistently 5–10 Hz (1.1–1.3 times) higher than those of sensors coated with a non-imprinted polymer. Geosmin, another tertiary alcohol odorant with an earthy odor resembling, and often accompanying MIB, produced almost equal responses on either imprinted- or non-imprinted sensors. A number of other odorants were examined and their responses to the non-imprinted sensors were found to be similar to or greater than their responses to the imprinted sensors. The responses of MIB to the imprinted sensors were always the highest, while other odorants produced equal or higher responses using the non-imprinted sensor. The sensor has a detection limit of ca. 5 mg l⁻¹ and a dynamic range of at least 1000 mg l^−l. When the time taken for the sensor to stabilize is used as the response, instead of the frequency change, the detection limit is lowered to ca. 200 μg l^−l.     

Selective recognition of sesamol using molecularly imprinted polymers containing magnetic wollastonite

The magnetic molecularly imprinted polymers (MMIPs) have been synthesized using piperonal molecules as dummy template and magnetic wollastonite composites as support. The resulting composites were applied to selective recognition of sesamol from aqueous solution. MMIPs were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) analysis, transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), thermogravimetric analysis (TGA), and vibrating sample magnetometer (VSM). MMIPs were demonstrated with an imprinted polymer film (90-100 nm) and exhibited magnetic property (M(s) =8.60 emu/g) and thermal stability. The effective average diameter of the Fe(3) O(4) nanoparticles was about 10 nm and the thickness of magnetic film was about 160 nm. Batch mode adsorption studies were carried out to investigate the specific adsorption equilibrium, kinetics and selective recognition. The Langmuir isotherm model was fitted to the equilibrium data better than the Freundlich model, and the kinetic properties were well described by the pseudo-second-order equation. The value of E(a) in this study was 5.35 kJ/mol for MMIPs. In addition, the selective recognition experiments demonstrated that MMIPs have specific recognition ability toward sesamol.     

Selective extraction of antioxidants with molecularly imprinted polymers

Molecular imprinting technology can be used to generate specific artificial polymeric receptors, i.e., high affinity stationary phases, as already shown for peptides and many other food ingredients. In this work, polymers have been molecularly imprinted with three exemplary antioxidants, butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and propyl gallate (PG). Results of chromatographic evaluations are presented, demonstrating the specificity of the imprinted polymers (MIP) compared to non-specific control polymers (CP). For a BHA imprinted polymer and the respective analyte BHA a separation factor of α=k_BHA-MIP′/k_CP′=1.12 was found, whereas for the BHT-MIP a higher selectivity was determined with α=k_BHT-MIP′/k_CP′=1.47. Using the PG selective MIP for PG as analyte a value of α=k_PG-MIP′/k_CP′=1.24 could be achieved. Furthermore, results of extraction procedures based on MIP and CP phases are presented, demonstrating for instance a higher selectivity of the BHA-MIP in comparison with its CP when using methanol or acetonitrile as analyte solvent, and of the PG-MIP when performing the extraction in acetonitrile.     

Clean up of phenylurea herbicides in plant sample extracts using molecularly imprinted polymers

Two different molecularly imprinted polymers (MIPs) were prepared by precipitation polymerization using linuron or isoproturon (phenylurea herbicides) as templates and trifluormethacrylic acid as functional monomer. These materials were used as selective sorbents in the development of molecularly imprinted solid-phase extraction (MISPE) procedures for the determination of several phenylurea herbicides (fenuron, metoxuron, chlortoluron, isoproturon, metobromuron, and linuron) in plant samples extracts. The MISPE procedures were fully optimized and applied to the clean up of selected phenylurea herbicides in carrot, potato, corn, and pea sample extracts and finally determined by HPLC-UV at 244 nm. Although a high degree of clean up was obtained, a decrease of the MIP recognition capabilities was observed in subsequent runs. Thus, a previous clean up protocol based on the use of a non-imprinted polymer was used to prevent the loss of MIP performance and to ease the removal of interferences. Following this procedure, namely two-step MISPE, matrix compounds were almost completely removed by the non-imprinted polymer retaining the ability of MIPs to selectively rebind target analytes unaltered. The developed MISPE procedures allowed the screening of phenylurea herbicides in plant samples at concentration levels required by established European maximum residue limits.     

Measurement of enantiomeric excess using molecularly imprinted polymers

[reaction: see text] A new method is presented for the measurement of enantiomeric excess (ee) utilizing molecularly imprinted polymers (MIPs). The method is demonstrated to be accurate and rapid, as the ee values can be calculated from straightforward concentration measurements. The MIP-based assay can also be adapted to measure the ee of samples of differing initial concentrations.     

Selective solid-phase extraction of tebuconazole in biological and environmental samples using molecularly imprinted polymers

Molecularly imprinted polymers (MIPs) were prepared by precipitation polymerization using tebuconazole (TBZ) as a template. Frontal chromatography and selectivity experiments were used to determine the binding capabilities and binding specificities of different MIPs. The polymer that had the highest binding selectivity and capability was used as the solid-phase extraction (SPE) sorbent for the direct extraction of TBZ from different biological and environmental samples (cabbage, pannage, shrimp, orange juice and tap water). The extraction protocol was optimized and the optimum conditions were: conditioning with 5 mL methanol:acetic acid (9:1), 5 mL methanol and 5 mL water respectively, loading with 5 mL aqueous samples, washing with 1.2 mL acetonitrile (ACN):phosphate buffer (5:5, pH3), and eluting with 3 mL methanol. The MIPs were able to selectively recognize, effectively trap and preconcentrate TBZ over a concentration range of 0.5–15 μmol/L. The intraday and interday RSDs were less than 9.7% and 8.6%, respectively. The limit of quantification was 0.1 μmol/L. Under optimum conditions, the MISPE recoveries of spiked cabbage, pannage, shrimp, orange juice and tap water were 62.3%, 75.8%, 71.6%, 89% and 93.9%, respectively. MISPE gave better HPLC separation efficiencies and higher recoveries than C18 SPE and strong cation exchange (SCX) SPE. Figure HPLC analysis of spiked pannage after MISPE (A) and after C18 SPE (B). HQ (1), E3 (2), p-NP (3), FTF (4), TBZ (5), PNZ (6), HXZ (7) Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Predicting the performance of molecularly imprinted polymers: Selective extraction of caffeine by molecularly imprinted solid phase extraction

A rational design approach was taken to the planning and synthesis of a molecularly imprinted polymer capable of extracting caffeine (the template molecule) from a standard solution of caffeine and further from a food sample containing caffeine. Data from NMR titration experiments in conjunction with a molecular modelling approach was used in predicting the relative ratios of template to functional monomer and furthermore determined both the choice of solvent (porogen) and the amount used for the study. In addition the molecular modelling program yielded information regarding the thermodynamic stability of the pre-polymerisation complex. Post-polymerisation analysis of the polymer itself by analysis of the pore size distribution by BET yielded significant information regarding the nature of the size and distribution of the pores within the polymer matrix. Here is proposed a stepwise procedure for the development and testing of a molecularly imprinted polymer using a well-studied compound—caffeine as a model system. It is shown that both the physical characteristics of a molecularly imprinted polymer (MIP) and the analysis of the pre-polymerisation complex can yield vital information, which can predict how well a given MIP will perform.     

Selective separation of magnolol using molecularly imprinted membranes

Molecularly imprinted membranes (MIMs) for selective separation of magnolol were prepared by thermal polymerization using magnolol as the template, ethylene glycol dimethacrylate (EGDMA) as the cross‐linker, 2,2‐azobisisobutyronitrile (AIBN) as the initiator, organic solvent as the porogen, methacrylamide (MAM) and acrylic acid (AA) as the functional monomers and cellulose acetate as the agglutinant. Commercial filter paper was used as the supporting material. The effects of different porogens and the ratio of functional monomers on the binding and recognition capacity of MIMs were investigated, and the morphology of the membranes was examined by scanning electron microscopy (SEM). The results showed that the MIMs have the highest selectivity to magnolol when the ratio of MAM/AA was 1:4 and tetrahydrofuran (THF) with dimethyl sulfoxide (DMSO) was used as the porogen. The morphology of the imprinted membranes after template extracting is much rougher with big cavities than that of the non‐imprinted membranes (NIMs) and the imprinted membranes before template extracting. The MIMs can selectively separate the magnolol.     

Selective recognition of ovalbumin using a molecularly imprinted polymer

Micro-contact imprinting has been used to form thin-film molecular imprints of ovalbumin (OVA) in polymers supported on glass slides. Thermocalorimetric data was used to optimise the choice of functional monomer and cross-linker to maximise selectivity and minimise non-specific recognition.A polymer comprising polyethyleneglycol 400 dimethacrylate (95 vol.%) and methacrylic acid (5 vol.%) showed both maximum recognition for OVA when made as a molecularly imprinted polymer (MIP), and minimal recognition when made as a non-imprinted, i.e. control polymer. OVA rebinding to the molecularly imprinted polymer, from a buffered 2 µM OVA solution, was 1.55 × 10^{− 11} mol cm^{− 2}, while the control polymer showed 10-fold less re-binding, i.e. 0.154 × 10^{− 11} mol cm^{− 2}.Experiments in which human serum albumin (HSA), conalbumin, ovomucoid or lysozyme, were re-bound to the polymers, either as single proteins or in competition with OVA, showed them to have low affinity for the polymer formulation used. Of the competing proteins examined, in non-competitive binding experiments, HSA showed the greatest affinity 0.45 × 10^{− 11} mol cm^{− 2} for the OVA imprinted polymer. In two protein competition experiments, i.e. with OVA and a competing protein present at equal concentrations (2 µM), OVA binding to the OVA imprinted polymer was in all cases significantly greater than that of the competitor.     

Comparison of particle size and flow rate optimization for chromatography using one-monomer molecularly imprinted polymers versus traditional non-covalent molecularly imprinted polymers

The dependence of enantio-selective chromatographic performance on particle size, as measured by separation factor, was investigated for one-monomer molecularly imprinted polymers (OMNiMIPs) compared to traditionally formed EGDMA/MAA molecularly imprinted polymers (MIPs). Five particle size ranges were compared (<20 μm, 20-25 μm, 25-38 μm, 38-45 μm, and 45-63 μm), revealing that the particle sizes above 25 μm provided the highest separation factor, and thus the best enantiomer separation, for both imprinted polymers. Other chromatographic parameters such as the number of theoretical plates and resolution exhibited only minor changes for the OMNiMIPs as the particle size changed, except for particles 20 μm and below. However, the number of theoretical plates and resolution for EGDMA/MAA are higher for particles in the 20-25 μm range. Thus, chromatographic factors for the EGDMA/MAA polymers are better in this range, despite better enantioselectivity for particle sizes above 25 μm. In contrast, OMNiMIPs generally show the most favorable performance for particle sizes in the 38-45 μm range. It was also found that decreasing flow rate resulted in improved enantioselectivity for both MIPs for all particle sizes.     

Selective enrichment and separation of phosphotyrosine peptides by thermosensitive molecularly imprinted polymers

Novel thermosensitive molecularly imprinted polymers were successfully prepared using the epitope imprinting approach in the presence of the mimic template phenylphosphonic acid, the functional monomer vinylphosphonic acid‐Ti⁴⁺, the temperature‐sensitive monomer N‐isopropylacrylamide and the crosslinker N,N′‐methylenebisacrylamide. The ratio of the template/thermosensitive monomers/crosslinker was optimized, and when the ratio was 2:2:1, the prepared thermosensitive molecularly imprinted polymers had the highest imprinting factor. The synthetic thermosensitive molecularly imprinted polymers were characterized by Fourier transform infrared spectroscopy to reveal the combination and elution processes of the template. Then, the adsorption capacity and thermosensitivity was measured. When the temperature was 28°C, the imprinting factor was the highest. The selectivity and adsorption capacity of the thermosensitive molecularly imprinted polymers for phosphotyrosine peptides from a mixture of three tailor‐made peptides were measured by high‐performance liquid chromatography. The results showed that the thermosensitive molecularly imprinted polymers have good selectivity for phosphotyrosine peptides. Finally, the imprinted hydrogels were applied to specifically adsorb phosphotyrosine peptides from a sample mixture containing phosphotyrosine and a tryptic digest of β‐casein, which demonstrated high selectivity. After four rebinding cycles, 78.9% adsorption efficiency was still retained.     

Chromatographic characterization of molecularly imprinted polymers

Recent efforts in the investigation of chromatographic characterization of molecularly imprinted polymers (MIPs) have focused mainly on the nature of heterogeneous binding sites. More data on the thermodynamics than on the kinetic features of MIP columns have been published. The present article addresses the sources of peak broadening and tailing, which are the main drawbacks often associated with imprinted polymers in chromatography for practical applications. With use of the theory of nonlinear chromatography, the peak properties of a MIP column, including the retention and peak broadening and tailing, can be well interpreted. Efforts to improve chromatographic efficiency using MIPs prepared by approaches different from the conventional method, including covalent imprinting and the format of uniformly sized spherical microbeads, are reviewed and discussed. This review leads to the conclusion that nonlinear chromatography theory is useful for characterizing chromatographic features of MIP columns, since a MIP is essentially an affinity-based chromatographic stationary phase. We expect more theoretical and experimental studies on the kinetic aspects of MIP columns, especially the factors influencing the apparent rate constant, as well as the analysis of the influences of mobile-phase composition on the chromatographic performance. In addition to revealing the affinity interaction by molecular recognition, slow nonspecific interactions which may be inherited from the imperfect imprinting and may be involved in the rebinding of the template to MIPs also need to be characterized. Figure The peak broadening and tailing associated often with molecularly imprinted polymers (MIPs) in column chromatography for practical applications can be well characterized by the theory of nonlinear chromatography.     

Thin-film electrochemical sensor for diphenylamine detection using molecularly imprinted polymers

This work reports on the development of a new voltammetric sensor for diphenylamine based on the use of a miniaturized gold electrode modified with a molecularly imprinted polymer recognition element. Molecularly imprinted particles were synthesized ex situ and further entrapped into a poly(3,4-ethylenedioxythiophene) polymer membrane, which was electropolymerized on the surface of the gold electrode. The thickness of the polymer layer was optimized in order to get an adequate diffusion of the target analyte and in turn to achieve an adequate charge transfer at the electrode surface. The resulting modified electrodes showed a selective response to diphenylamine and a high sensitivity compared with the bare gold electrode and the electrode modified with poly(3,4-ethylenedioxythiophene) and non-imprinted polymer particles. The sensor showed a linear range from 4.95 to 115 μM diphenylamine, a limit of detection of 3.9 μM and a good selectivity in the presence of other structurally related molecules. This sensor was successfully applied to the quantification of diphenylamine in spiked apple juice samples.     

Isolation of sinapic acid from broccoli using molecularly imprinted polymers

A molecularly imprinted polymer was synthesized for the purpose of sinapic acid isolation from Egyptian nutraceutical Botrytis italica, L. (broccoli) due to its prominent medicinal and wide pharmacological activities. A computational study was first developed to determine the optimal template to functional monomer molar ratio. Based on the computational results, five polymers were synthesized using a bulk polymerization method with sinapic acid as the template molecule. Evaluation of the synthesized polymers binding performance was carried out using batch rebinding assay, which revealed that the molecularly imprinted polymer of molar ratio (1:4:20), template to functional monomer (4‐vinyl pyridine) to crosslinker (ethylene glycol dimethacrylate) was of optimum performance, thus, this polymer was applied for sinapic acid isolation from closely related analogues. This represents a more practical approach to isolate sinapic acid from different natural extracts selectively.     

C-reactive protein thin-film molecularly imprinted polymers formed using a micro-contact approach

A method for micro-contact imprinting CRP has been developed. An analogue, O-(-4-nitrophenylphosphoryl)choline, of the templates natural ligand, phosphorylcholine, was used as the functional monomer. A series of non-imprinted polymers made without template, but with varying cross-linking agents, were made in order to produce a control polymer with minimal non-specific recognition.The affinity of the imprinted polymers for the competing proteins, lysozyme and albumin, was examined. Their respective relative affinities, with 1.04 μg/cm² of the template protein bound to the imprinted surface as reference, were CRP/albumin = 4.0 and CRP/lysozyme = 346. Measurement of the film thickness showed it to be approximately 10 μm.A competitive binding experiment showed the CRP imprinted material to retain good selectivity for its template when jointly incubated with human serum albumin and CRP. Using the same method we were able to form a micro-contact imprint of human serum albumin which demonstrated relatively good recognition for its own template 2.66 μg/cm² compared with 0.27 μg/cm² for CRP.     

分子印迹样品前处理技术的研究进展

样品前处理是分析过程的关键环节,直接影响着分析结果的准确度和精密度．分子印迹聚合物具有特异性识别能力,能从复杂样品中选择性分离富集目标物,在复杂样品前处理领域中有重要的发展潜力和应用前景．本文综述了近年来分子印迹样品前处理技术的研究进展,包括分子印迹固相萃取、分子印迹固相微萃取、分子印迹膜萃取等样品前处理技术．     

Carbohydrate recognition by porphyrin-based molecularly imprinted polymers

[structure: see text] Porphyrin-based molecularly imprinted polymers (MIPs) were prepared for carbohydrate recognition. A urea-appended porphyrin functional monomer was utilized to provide complementary functionality and quality binding sites throughout the polymer. Each porphyrin-based polymer demonstrates high affinity and differential selectivity for closely related carbohydrates that correlate to the structure of the template used in the imprinting process.     

Citrinin selective molecularly imprinted polymers for SPE

Molecularly imprinted polymers (MIPs) for citrinin (Cit) with 1‐hydroxy‐2‐naphthoic acid (HNA) as mimic template were prepared and the molecularly imprinted SPE method was developed for the detection of Cit in rice with HPLC. The adsorption properties of HNA and Cit on the MIPs and nonimprinted polymers were investigated. It proved that MIPs showed higher selectivity adsorption to HNA and Cit than nonimprinted polymers were. The recoveries of Cit in rice were in the range of 86.7–97.7%. The spiked rice samples and five rice samples in Beijing market were detected using molecularly imprinted SPE method and satisfied results were obtained as discussed in this article.