Surface and interfacial structure of epitaxial SrTiO3 thin films on (0 0 1) Si grown by molecular beam epitaxy

Effects of relaxation of interfacial misfit strain and non-stoichiometry on surface morphology and surface and interfacial structures of epitaxial SrTiO₃ (STO) thin films on (0 0 1) Si during initial growth by molecular beam epitaxy (MBE) were investigated. In situ reflection high-energy electron diffraction (RHEED) in combination with X-ray diffraction (XRD), atomic force microscopy (AFM), X-ray photoelectron spectrometry (XPS) and transmission electron microscopy (TEM) techniques were employed. Relaxation of the interfacial misfit strain between STO and Si as measured by in situ RHEED indicates initial growth is not pseudomorphic, and the interfacial misfit strain is relaxed during and immediately after the first monolayer (ML) deposition. The interfacial strain up to 15 ML results from thermal mismatch strain rather than lattice mismatch strain. Stoichiometry of STO affects not only surface morphology but interfacial structure. We have identified a nanoscale Sr₄Ti₃O₁₀ second phase at the STO/Si interface in a Sr-rich film.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

蓝色荧光粉Sr3LnM(PO4)3F:Eu2+的发光调控

采用高温固相法合成了一系列Eu²⁺激活的Sr₃LnM(PO₄)₃F(Ln=Gd, La, Y; M= Na, K)荧光粉,并通过X射线衍射、扫描电子显微镜、荧光光谱等对样品的物相结构、形貌和发光特性进行了表征及分析。结果表明:成功合成了Sr₃LnM(PO₄)₃F:Eu²⁺荧光粉,样品的粒径为2~10 μm。荧光粉在蓝光区具有强烈的发射,归属为发光中心Eu²⁺的4f⁶5d→4f⁷跃迁。当基质中的碱金属M由Na变成K时,Eu²⁺的发光颜色由淡蓝色变成深蓝色,色纯度大幅提高,有效地调控了Eu²⁺在氟磷灰石Sr₃LnM(PO₄)₃F中的发光,进而发现了一种通过改变第二层配位原子来调控Eu²⁺发光的策略。     

Preparation of CdS nanowires by the decomposition of the complex in the presence of microwave irradiation

A novel synthetic route for the preparation of CdS nanowires has been developed. CdS nanowires with a diameter of ca. 4 nm have been successfully prepared by the microwave irradiation of a complex of cadmium-1-pyrrlidine dithio carboxylic acid ammonium (C₅H₁₂N₂S₂, APDTC) [Cd(APDTC)₂]₂ in an ethylenediamine solution. The CdS nanowires were characterized by powder X-ray diffraction pattern, transmission electron microscopy (TEM), UV-Vis spectroscopy, diffuse reflection spectroscopy and PL spectroscopy.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Properties of ZnO films grown on (0 0 0 1) sapphire substrate using H2O and N2O as O precursors by atmospheric pressure MOCVD

In this paper, we compare the properties of ZnO thin films (0 0 0 1) sapphire substrate using diethylzinc (DEZn) as the Zn precursor and deionized water (H₂O) and nitrous oxide (N₂O) as the O precursors, respectively in the main ZnO layer growth by atmospheric pressure metal–organic chemical vapor deposition (AP-MOCVD) technique. Surface morphology studied by atomic force microscopy (AFM) showed that the N₂O-grown ZnO film had a hexagonal columnar structure with about 8 μm grain diameter and the relatively rougher surface compared to that of H₂O-grown ZnO film. The full-widths at half-maximum (FWHMs) of the (0 0 0 2) and () ω-rocking curves of the N₂O-grown ZnO film by double-crystal X-ray diffractometry (DCXRD) measurement were 260 and 350 arcsec, respectively, indicating the smaller mosaicity and lower dislocation density of the film compared to H₂O-grown ZnO film. Compared to H₂O-grown ZnO film, the free exciton A (FX_A) and its three phonon replicas could be clearly observed, the donor-bound exciton A⁰X (I₁₀):3.353 eV dominated the 10 K photoluminescence (PL) spectrum of N₂O-grown ZnO film and the hydrogen-related donor-bound exciton D⁰X (I₄):3.363 eV was disappeared. The electron mobility (80 cm²/V s) of N₂O-grown ZnO film has been significantly improved by room temperature Hall measurement compared to that of H₂O-grown ZnO film.     

Porous glass-ceramics composed of a titanium phosphate crystal skeleton: A review

Bulk microporous glass-ceramics with a skeleton of two types of functional titanium phosphate crystal were prepared by controlled crystallization of RTi₂(PO₄)₃ (

Full-size image

glasses, and chemical treatment. One crystal is a NASICON-type with a three-dimensional network structure of TiO₆ and PO₄ while the other is a zirconium phosphate-type crystal Ti(HPO₄)₂ · 2H₂O with a two-dimensional layered structure. The mean pore diameter and porosity of 30–60 nm and 40–60 vol.% were achieved. Porous CaTi₄(PO₄)₆ glass-ceramics have excellent properties as supports for immobilization of enzymes, humidity sensors and porous LiTi₂(PO₄)₃ glass-ceramics as ion exchange media. Conspicuous bacteriostatic activities were found for the partially Ag-exchanged porous LiTi₂(PO₄)₃ and Li_1.4Ti_1.6Al_0.4(PO₄)₃. Integrated microporous glass-ceramics with skeletons of LiTi₂(PO₄)₃ (LTP) and Ti(HPO₄)₂ · 2H₂O (TP) crystals were synthesized utilizing a novel discovery that LTP is transformed into TP in acid solution.     

Synthesis, thermal and magnetic properties of new metal iodate: (LiFe1/3)(IO3)2

This paper reports the detail synthesis of a new kind of metal iodate, anhydrous (LiFe_1/3)(IO₃)₂, from aqueous solutions. The synthesized compound shows spinal morphology and is chemical stable up to 400°C. The iodate shows paramagnetic behavior from room temperature down to 4.2 K. At room temperature, the new compound has a hexagonal structure with the lattice parameters a=5.4632(2) Å, c=5.0895(6) Å, Z=1, space group of P6₃.     

Effect of NH3 on the growth characterization of TiN films at low temperature

Titanium nitride (TiN) films were obtained by the atmospheric pressure chemical vapor deposition method of the TiCl₄–N₂–H₂ system with various flow rates of NH₃ at 600°C. The growth characteristics, morphology and microstructure of the TiN films deposited were analyzed by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Without NH₃ addition, no TiN was deposited at 600°C as shown in the X-ray diffraction curve. However, by adding NH₃ into the TiCl₄–N₂–H₂ system, the crystalline TiN was obtained. The growth rate of TiN films increased with the increase of the NH₃ flow rate. The lattice constant of TiN films decreased with the increase of the NH₃ flow rate. At a low NH₃ flow rate, the TiN (2 2 0) with the highest texture coefficient was found. At a high NH₃ flow rate, the texture coefficient of TiN (2 0 0) increased with the increase of the NH₃ flow rate. In morphology observation, thicker plate-like TiN was obtained when the NH₃ flow rate was increased. When the flow rate of NH₃ was 15 sccm, Moiré fringes were observed in the TiN film as determined by TEM analysis. The intrinsic strain was found in the TiN film as deposited with 60 sccm NH₃.     

Textural properties of synthetic nano-calcite produced by hydrothermal carbonation of calcium hydroxide

The hydrothermal carbonation of calcium hydroxide (Ca(OH)₂) at high pressure of CO₂ (initial P_CO2=55 bar) and moderate to high temperature (30 and 90 °C) was used to synthesize fine particles of calcite. This method allows a high carbonation efficiency (about 95% of Ca(OH)₂–CaCO₃ conversion), a significant production rate (48 kg/m³ h) and high purity of product (about 96%). However, the various initial physicochemical conditions have a strong influence on the crystal size and surface area of the synthesized calcite crystals. The present study is focused on the estimation of the textural properties of synthesized calcite (morphology, specific surface area, average particle size, particle size distribution and particle size evolution with reaction time), using Rietveld refinements of X-ray diffraction (XRD) spectra, Brunauer–Emmett–Teller (BET) measurements, and scanning electron microscope (SEM) and transmission electron microscope (TEM) observations. This study demonstrate that the pressure, the temperature and the dissolved quantity of CO₂ have a significant effect on the average particle size, specific surface area, initial rate of precipitation, and on the morphology of calcium carbonate crystals. In contrast, these PTx conditions used herein have an insignificant effect on the carbonation efficiency of Ca(OH)₂.

Finally, the results presented here demonstrate that nano-calcite crystals with high specific surface area (S_BET=6–10 m²/g) can be produced, with a high potential for industrial applications such as adsorbents and/or filler in papermaking industry.     

Controlled synthesis of different morphologies of BaWO4 crystals via a surfactant-assisted method

BaWO₄ crystals with different morphologies, such as nanosheets, nanobelts, flower-like, quadrangled plates and sheaves of dendrite, have been successfully synthesized via PVP as templates. Our result shows that reaction parameters, such as the concentration of PVP aqueous solutions, pH value of the starting solution and molar ratio of [Ba²⁺]/[WO₄²⁻] played important roles in the formation of BaWO₄ crystal with different morphologies. It is obviously different between microwave irradiation heating and oil bath heating. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and electron diffraction.     

Self-catalytic branch growth of SnO2 nanowire junctions

Multiple branched SnO₂ nanowire junctions have been synthesized by thermal evaporation of SnO powder. Their nanostructures were studied by transmission electron microscopy and field emission scanning electron microcopy. It was observed that Sn nanoparticles generated from decomposition of the SnO powder acted as self-catalysts to control the SnO₂ nanojunction growth. Orthorhombic SnO₂ was found as a dominate phase in nanojunction growth instead of rutile structure. The branches and stems of nanojunctions were found to be an epitaxial growth by electron diffraction analysis and high-resolution electron microscopy observation. The growth directions of the branched SnO₂ nanojunctions were along the orthorhombic [1 1 0] and . A self-catalytic vapor–liquid–solid growth mechanism is proposed to describe the growth process of the branched SnO₂ nanowire junctions.     

Seed-mediated synthesis of uniform ZnO nanorods in the presence of polyethylene glycol

Large quantities of ZnO nanorods have been synthesized by the seed-mediated method in the presence of polyethylene glycol at 90 °C. The products are characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy and high-resolution transmission electron microscopy. The as-grown ZnO nanorods are uniform with a diameter of 40–70 nm and length about 2 μm. The nanorods grew along the [0 0 1] direction. Possible roles of ZnO seeds and polymer in the growth of ZnO nanorods are also discussed.     

Growth of nanofibrous barium carbonate on calcium carbonate seeds

Fibrous barium carbonate (BaCO₃/witherite) crystals 50–100 nm in diameter and several microns in length were grown on calcium carbonate (CaCO₃) seeds at temperatures as low as 4 °C. The BaCO₃ fibers were deposited onto calcite rhombs or CaCO₃ films using the polymer-induced liquid-precursor (PILP) process, which was induced with the sodium salt of polyacrylic acid (PAA). The structure and morphology of the resultant fibers were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), and polarized light microscopy (PLM). Fibers were successfully grown on calcite seeds of various morphologies, with a range of barium concentrations, and PAA molecular weight and concentration. Two categories of fibers were grown: straight and twisted. Both types of fibers displayed single-crystalline SAED diffraction patterns, but after examining high-resolution TEM lattice images, it was revealed that the fibers were in fact made up of nanocrystalline domains. We postulate that these nanocrystalline domains are well aligned due to a singular nucleation event (i.e., each fiber propagates from a single nucleation event on the seed crystal) with the nanocrystalline domains resulting from stresses caused by dehydration during crystallization of the highly hydrated precursor phase. These BaCO₃ fibers grown on calcite substrates further illustrate the robustness and non-specificity of the PILP process.     

Growth of Na modified potassium lithium niobate crystal by the Czochralski method

Transparent Na modified potassium lithium niobate (Na_0.23K_2.60Li_1.82Nb_5.35O_15.70; NKLN) crystal was successively grown by the Czochralski method using RF induction heating from melt composition Na₂O:K₂O : Li₂O:Nb₂O₅=2:30:25:43 mol%. NKLN crystal showed a tetragonal tungsten bronze structure with lattice constants a=12.5446±0.0010 Å and c=4.0129±0.0005 Å at room temperature. The dielectric constant along the c-axis ε₃₃ showed a sharp maximum around 480 °C. Optical transmission edge was 370 nm and optical transmission spectra showed no absorption at wavelengths ranging from 380 to 800 nm. The structural and optical properties of NKLN were similar to those of the near stoichiometric KLN crystals. We believe that the growth of NKLN by the Czochralski method has an advantage for a large size and high-quality crystal.     

Large-scale synthesis of uniform Cu2O stellar crystals via microwave-assisted route

A convenient microwave-assisted process has been applied to prepare stellar Cu₂O crystals. The products were characterized via X-ray diffraction pattern (XRD), transmission electron microscopy images (TEM) and UV-VIS absorption spectrum. The results showed that the as-prepared Cu₂O stellar crystals have regular shape and uniform size distribution. The influences of microwave irradiation and the concentration of starting agents on the morphology of the products were also discussed.     

Hydrothermal growth of single-crystal CaV6O16·3H2O nanoribbons

CaV₆O₁₆·3H₂O nanoribbons have been prepared by the hydrothermal method in the presence of sodium dodecyl sulfate (SDS) at 160°C for 10 h. X-ray diffraction pattern indicates that the sample is monoclinic phase of CaV₆O₁₆·3H₂O with the lattice contents a=12.18 Å, b=3.598 Å, c=18.39 Å, β=118.03°. Field emission scanning electron microscopy shows that the nanoribbons have widths in the range of 150–500 nm, thicknesses of 30–60 nm and lengths of 500 mm X-ray photoelectron spectrum measurements further confirm the formation of the CaV₆O₁₆·3H₂O phase. The formation of CaV₆O₁₆·3H₂O nanoribbons is a self-assembling process, in which surfactant SDS plays the role of soft template.     

The effect of oxygen pressure on the microstructures of Co-doped rutile TiO2 thin films grown by pulsed laser deposition

Comprehensive microstructures of 7% cobalt-doped rutile TiO₂ thin films grown on c-plane sapphire by pulsed laser deposition were characterized using transmission electron microscopy (TEM). The effects of oxygen pressure during growth on the Co distribution inside the films were investigated, and the detailed growth mechanism of both TiO₂ and TiO₂+Co was discussed. The similar oxygen sublattices and low mismatch between (1 0 0) rutile and c-plane sapphire favors the rutile phase. However, the three-fold symmetry of the substrate surface resulted in three rutile domain orientation variants, and they grow adjacent to each other. Cobalt was found to precipitate out as nanocrystals inside the TiO₂ matrix as the growth pressure of oxygen was decreased. At 0.05 mTorr oxygen pressure, almost all of the Co segregates into crystallographically aligned nanocrystals with a particle size of 4.4±0.15 nm. All the samples have magnetic coercivity at room temperature. The magnetic moment per Co atom increased with decreased oxygen pressure, suggesting that the Co that replaced the Ti²⁺ in the TiO₂ lattice does not have a large magnetic moment.     

Mechanochemical–hydrothermal synthesis of hydroxyapatite from nonionic surfactant emulsion precursors

Nanocrystalline hydroxyapatite [HA, Ca₁₀(PO₄)₆(OH)₂] powders were synthesized by the mechanochemical–hydrothermal method using emulsion systems consisting of aqueous phase, petroleum ether (PE) as the oil phase and biodegradable Tomadol 23–6.5 as the nonionic surfactant. (NH₄)₂HPO₄ and Ca(NO₃)₂ or Ca(OH)₂ were used as the phosphorus and calcium sources, respectively. The calcium source and emulsion composition had significant effects on the stoichiometry, crystallinity, thermal stability, particle size and morphology of final products. Disperse HA crystals with a 160 nm length and aspect ratio of ca. 6 were formed in an emulsion system containing 10 wt% PE, 60 wt% water and 30 wt% surfactant. The HA particles had needle morphology with a specific surface area of . With this technique, HA nanopowders with specific surface areas in the range of 72– were produced.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.