Indirect determination of lutetium by differential pulse anodic stripping voltammetry at a hanging mercury drop electrode

Lutetium has been determined by differential pulse anodic stripping voltammetry in an acidic solution containing Zn-EDTA. Lutetium (III) ions liberated zinc (II), which was preconcentrated on a hanging mercury drop electrode and stripped anodically, resulting in peak current linearly dependent on lutetium (III) concentration. Less than 0.4 ng mL⁻¹ lutetium could be detected after a 2 min deposition.      

Nanoporous carbon — metal composites for hydrogen storage

Metal-carbon composites have shown considerable hydrogen storage potential at room temperature. In the present work the behaviour of two different Pd amalgam doped carbon substrates, namely a carbogenic foam and a mildly oxidised ordered mesoporous carbon, are compared on the basis of their hydrogen sorption properties at 77 and 298 K and low pressures, aiming to investigate the effect of surface on the storage capacity. In both cases, the introduction of alloy nanoparticles leads to an improvement of the hydrogen uptake with respect to pure carbons. This effect is significant for the carbogenic foam however small for the ordered carbon.      

Diironcarbonyl-coumarin complex: preparation, intramolecular electron transfer, and electro-generation of hydrogen

A new organometallic complex coupling photoactive coumarin to a diironhexacarbonyl unit has been successfully prepared and its composition and electronic structure confirmed by elemental and spectroscopic analyses. Emission spectral analysis of the complex reveals photoinduced intramolecular electron transfer from coumarin to the iron-carbonyl moiety. The compound is electrochemically reduced at −1.24 V vs. Fc/Fc⁺. This reduction is irreversible, attesting to the instability of the complex. Electrochemical evolution of hydrogen in the presence of the complex has been studied and results are discussed.      

Methylcellulose/SiO<Subscript>2</Subscript> hybrids: sol-gel preparation and characterization by XRD,FTIR and AFM

Methylcellulose (MC) / SiO₂ organic / inorganic hybrid materials have been prepared from MC and methyltriethoxysilane or ethyltrimethoxysilane, and characterized by XRD, FTIR and AFM. XRD showed peak shifts. FTIR shows intermolecular hydrogen bonding between MC and SiO₂. AFM depicts surface roughness which depends on the silica precursor and MC content.      

Electrochemical oxidation of methylthiomethyleneisoquinolinium chloride — the first water soluble alkylthiomethylene substituted ammonium salt

Electrochemical oxidation of methylthiomethyleneisoquinolinium chloride (MTMIQ), the first alkylthiomethyl substituted ammonium salt, which is fully miscible with water has been investigated by voltammetric (SWV) method using glassy carbon electrode. On the electrode, MTMIQ undergoes oxidation at the potential near Ep = 0.07V (vs. Ag/AgCl/3 M KCl). The influence of the pH of buffers, amplitude, frequency, step potential on the received signal was studied. The best results were obtained with a citrate buffer at a pH of 5. The oxidation peak current used for MTMIQ voltammetric determination was in the range of 2–8×10⁻⁵ mol L⁻¹, LOD = 3.7×10⁻⁶, LOQ = 1.2×10⁻⁵. The product of the oxidation was accumulated at the working electrode and was investigated by spectroscopic method. Mechanistic pathways of the oxidation have been proposed.      

Miniaturization of flow-through generation cells for electrochemical hydride generation in AAS

The construction and optimization of five new types of miniaturized flow-through electrolytic cells with lead cathode and platinum anode for electrochemical hydride generation in atomic absorption spectrometry (HG-QFAAS) were achieved during this research study. The ion-exchange membrane was not part of these cells and only one carrying electrolyte for both electrode chambers was used. Hydride generation efficiency achieved was either comparable or higher than the one recorded for the classic thin-layer generation cell. The inner volume of the cathode chamber was reduced to a quarter of the classic thin-layer flow-through cell. Compared to the commonly used thin-layer flow-through cell, higher sensitivity (7.32×10³ dm³ μg⁻¹) and better limit of detection (0.32 μg dm⁻³) were obtained for selenium determination using two of these new generators.      

Meldola’s Blue — doped titania sol-gel sensor for NADH determination

Titania layers obtained by a sol-gel technique doped with redox mediator, Meldola’s Blue, were employed for construction of a new NADH senor. Optimization of preparation process as well as experimental conditions affecting the response of the sensor were examined. Under optimal conditions NADH could be determined in the wide linear range from 90 to 2300 μM with detection limit 12 μM and a high sensitivity 12.5 nA μM⁻¹. The usefulness of developed sensor was preliminarily checked in determination of NADH forming during enzymatic oxidation of ethanol catalyzed by alcohol dehydrogenase (ADH).      

Determination of diclofenac in pharmaceuticals and urine samples using a membrane sensor based on the ion associate of diclofenac with Rhodamine B

The potentiometric response characteristics of a diclofenac selective electrode, based on ion association in different plasticizers, were compared. The sensitivity, working range, detection limit and selectivity of membrane sensors demonstrated significant dependence on the type of plasticizers. The potentiometric unit presented a linear response toward diclofenac concentrations between 1 × 10⁻⁵ − 5 × 10⁻² mol L⁻¹, with slopes of approximately 60 mV dec⁻¹, and exhibited a response time of 3 s. The potentiometric analysis of sodium diclofenac in pharmaceutical formulations was perfomed by the membrane electrode proposed and compared with the results of potentiometric titration given by the Pharmacopoeia of Ukraine.      

Properties of ibuprofen ion-selective electrodes based on the ion pair complex of tetraoctylammonium cation

Ibuprofen membrane electrodes based on different plasticizers: diisobutyl phthalate (DIBP), o-nitrophenyloctyl ether (o-NPOE), dioctyl sebacate (DOS) and tetraoctylammonium 2-(4-isobutylphenyl)propionate were prepared. All electrodes show: a near Nernstian slope of characteristic (58.3–60.9 mV decade⁻¹) in the measurement range (10⁻⁴–10⁻¹ mol L⁻¹), limit of detection (5.0×10⁻⁵ mol L⁻¹), really long lifetime (12 months), dependence of the electrode potential on pH (5.5–9.0), reproducibility of potential (0.6–1.2 mV) and selectivity coefficients in relation to some organic and inorganic anions. The electrodes were applied for the determination of ibuprofen in tablets by the calibration curve method and the standard addition method.      

Ionic liquid promoted Diels-Alder Reaction between anthrone and maleimides

Ionic liquids (IL) are gaining importance as green solvents. Imidazolium ionic liquid [bmim]⁺[Cl]⁻, an environmentally benign solvent, was found to promote the Diels-Alder reaction between anthrone and maleimides at room temperature with excellent yields. The ionic liquid played a dual role as solvent and catalyst.      

Method validation in quantitative electrochemical analysis of colchicine using glassy carbon electrode

A cathodic differential pulse voltammetric determination of colchicine was validated using a glassy carbon electrode in HClO₄/H₃PO₄ 0.01 M. Colchicine gives an irreversible, diffusion-controlled peak at −862 mV vs. Ag/AgCl reference electrode. The cathodic peak is strongly influenced by a more alkaline environment with a shift towards more negative potentials. Method optimization was carried out in parallel for three types of electrodes (glassy carbon, mercury film and bismuth film coated glassy carbon). The cathodic peak current is higher using film-coated electrodes, but shows poorer intra-day reproducibility and a longer analysis time due to film renewal. Thus, a bare glassy carbon electrode was used to determine colchicine in the concentration range of 2.4 − 50 μg mL⁻¹ (R ² = 0.9998, n = 5), with a calculated detection limit of 0.80 μg mL⁻¹. The proposed method was characterized according to ICH Harmonized Tripartite Guidance Q2(R1) by validation parameters (selectivity, linearity, accuracy, fidelity, limit of detection, limit of quantification) and it was successfully applied for the determination of colchicine from tablets, without the interference of the excipients. The method’s performances were evaluated and compared with both a known polarographic method and the official quantitative spectrophotometric determination from the Romanian Pharmacopoeia, Xth edition, respectively.      

Equilibrium and kinetic study of the proton transfer reactions between nitroalkanes and strong organic bases — phosphazenes in tetrahydrofuran solvent

Proton transfer reactions rates between carbon acids 1-nitro-1-(4-nitrophenyl)ethane (NPNE), 2-methyl-1-nitro-1-(4-nitrophenyl)propane (MNPNP)) and phosphazenes (BEMP, BTPP, P₁-t-Oct) in tetrahydrofuran have been measured, and the activation parameters were determined. The results are compared with those previously obtained for P₁-t-Bu phosphazene, guanidines and amidines.      

Preparation and examination of multilayer graphene nanosheets by exfoliation of graphite in high efficient attritor mill

Graphene multilayers have been prepared by mechanical method based on milling graphite in high efficient attritor mill. The results showed that the best dispersion media is ethanol, and 10 hours of intensive milling proved to be the most efficient way to separate the graphite layers as it was shown by scanning electron microscopy and X-ray diffraction measurements.      

Voltammetric and amperometric determination of metoclopramide on boron-doped diamond film electrode

New methods for the determination of metoclopramide, antiemetic and gastroprokinetic pharmaceutical, were developed, using differential pulse voltammetry (DPV) and flow injection analysis (FIA) with amperometric detection on a boron-doped diamond film electrode. Electrode pretreatment necessary to ensure the stable results was investigated and it was found, that while DPV requires frequent electrode cleaning, FIA with a sufficiently high flow rate can maintain a stable signal with no signs of electrode passivation. The calculated quantification limits of the DPV and FIA with amperometric detection were 0.13 μmol L⁻¹ and 0.015 mmol L⁻¹, respectively. The applicability of the new methods was verified by the determination of metoclopramide in a pharmaceutical preparation. FIA with amperometic detection proved to be sensitive, accurate and, due to the resistance of the electrode to the passivation, also simple to handle.      

Properties of naproxen ion-selective electrodes

Naproxen membrane electrodes based on different plasticizers and the quaternary ammonium salts (QASs) dimethyldidecylammonium bromide, methyltrioctylammonium chloride, or tetraoctylammonium chloride, were prepared. The following basic parameters were investigated for the optimal electrode: measurement range (10⁻⁴ − 10⁻¹ mol L⁻¹), slope of the linear range of the calibration curve (−58.3 mV decade⁻¹), limit of detection (6.0 × 10⁻⁵ mol L⁻¹), lifetime (2.5 months), dependence of the electrode potential on pH (5.5 − 9.0), reproducibility of potential (1.2 mV) and selectivity coefficients in relation to selected organic and inorganic anions. The electrode was utilized for determination of naproxen in tablets by the calibration curve method and the standard addition method.      

Voltammetric determination of some alkaloids and other compounds in pharmaceuticals and urine using an electrochemically activated glassy carbon electrode

Electrochemical behaviour of some alkaloids, namely: caffeine, aminophylline, theophylline, codeine phosphate and papaverine hydrochloride, that are in solution in various combinations or in the presence of other compounds contained in pharmaceuticals or in real samples (urine) was investigated using cyclic voltammetry (CV), square-wave voltammetry (SWV) and differential pulse voltammetry (DPV) on electrochemically activated glassy carbon electrode.      

A new zinc complex of 1-propyl-1H-benzo[d] imidazole: synthesis, characterization and electrocatalysis

The present work reports the synthesis, characterization and performance of a new zinc(II) complex of [Zn(C₃H₇-bim)₂Br₂] (bim = benzimidazole) as electrocatalyst for trichloroacetic acid and bromate reduction. Its structure was characterized by X-ray crystallography, IR spectroscopy and elemental analysis. The zinc atom adopts a distorted tetrahedral geometry by coordinating to two bromine atoms and two nitrogen atoms from two 1-propyl-1H-benzo[d]imidazole ligands. The electrochemical behavior and electrocatalysis of the zinc complex bulk-modified carbon paste electrode (Zn-CPE) have been studied by cyclic voltammetry. The Zn-CPE shows good electrocatalytic activities toward the reduction of trichloroacetic acid and bromate. The detection limit and the sensitivity are 0.05 μM, 67.43 μA μM⁻¹ for trichloroacetic acid detection, and 0.02 μM, 69.94 μA μM⁻¹ for bromate detection, respectively. This modified electrode shows good reproducibility, high stability, low detection limit, technical simplicity and possibility of rapid preparation, which is important for practical applications.      

Asymmetric transfer hydrogenation of prochiral ketones catalyzed by aminosulfonamide-ruthenium complexes in ionic liquid

Chiral aminosulfonamides containing imidazolium group were used as ligands for the ruthenium(II)-catalyzed asymmetric transfer hydrogenation of prochiral ketones in ionic liquid, affording good to excellent conversions and enantiomeric excesses. The catalytic system could be easily recovered and reused several times.      

Effect of the polymeric coating over Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> particles used for magnetic separation

In this work, the synthesis of magnetite nanoparticles by two variant chemical coprecipitation methods that involve reflux and aging conditions was investigated. The influence of the synthesis conditions on particle size, morphology, magnetic properties and protein adsorption were studied. The synthesized magnetite nanoparticles showed a spherical shape with an average particle size directly influenced by the synthesis technique. Particles of average size 27 nm and 200 nm were obtained. When the coprecipitation method was used without reflux and aging, the smallest particles were obtained. Magnetite nanoparticles obtained from both methods exhibited a superparamagnetic behavior and their saturation magnetization was particle size dependent. Values of 67 and 78 emu g⁻¹ were obtained for the 27 nm and 200 nm magnetite particles, respectively. The nanoparticles were coated with silica, aminosilane, and silica-aminosilane shell. The influence of the coating on protein absorption was studied using Bovine Serum Albumin (BSA) protein.