西兰花中13种有机含磷农药在不同色谱柱上的色谱保留行为

应用Agilent GC 6890气相色谱仪(附FPD检测器)对13种残留于西兰花中的有机含磷农药(OPP′s)在4种不同极性的毛细管色谱柱(即DB-1、DB-5、DB-1701及DB-35MS)上的保留行为作了研究。结果表明:采用由DB-5及DB-1701串联组成的色谱柱单元,西兰花中13种残留OPP′s可达到有效分离和测定。     

移动子窗口中搜索法在紫丁香挥发油气相色谱-质谱分析中的应用

基于气相色谱-质谱仪产生的二维数据,采用移动子窗口搜索法,以纯组分峰为标准对同一样品在不同色谱柱上或不同样品在相同色谱柱上所获得的总离子流图的一定保留时间范围内搜索,可以得到目标化合物的流出区域,取其中点作为保留时间,从而计算各化合物在不同极性色谱柱上的程序升温保留指数.采用GC-MS与色谱保留指数相结合的方法,分别在HP-5MS和DB-35MS柱上,于80℃～290℃(4℃/min)的升温程序下,对黑龙江产紫丁香花蕾与花挥发油的分析结果表明,辅以化学计量学方法和双柱色谱保留指数定性比单用GC-MS定性结果更加快速可靠.     

烃类化合物在不同色谱柱上的定量结构-保留相关性研究

运用量子化学中的AMI方法计算烃类化合物的分子结构描述参数,借助逐步回归法建立了烃类化合物在不同极性色谱柱上的QSRR模型。结果表明：烷烃、烯烃、二烯烃类化合物在不同极性的色谱柱上的色谱保留与其分子结构描述参数之间具有较好的线性关系,烃类化合物在不同极性固定相上的保留主要与溶质分子的MR有关,即与溶质分子的色散力有关。随着溶质分子的不饱和度的增加,或固定相极性的增强,溶质分子与固定相之间的电荷传递作用随之增强。而且,烃类化合物在不同极性固定相上的色谱保留的QSRR模型均可用量化参数HOMO、LUMO、EICE以及MR参数来描述。所建立的在不同极性色谱柱上的烃类化合物的色谱保留QSRR模型预测烃类化合物的色谱保留值时具有较好的稳定性和准确性。     

新型季磷离子液体气相色谱柱的制备及应用

选择季磷型离子液体为气相色谱固定相,采用静态法将其涂渍于纳米级SiO2预处理的毛细管内壁上制备成毛细管气相色谱柱.考察了此固定相的基本色谱性能和极性,并详细研究了其对多种化合物的分离性能和保留特点.研究表明,此该离子液体色谱柱的柱效为1381 plates/m,极性为559.6,与商品化的聚乙二醇(PEG20M)和硝基对苯二甲酸改性的聚乙二醇(FFAP)柱的极性相近.此固定相对给质子体化合物的保留作用明显强于PEG20M,并且其对芳香化合物的间位和对位异构体的分离选择性明显优于自制的PEG20M.此固定相对芳香位置异构体、烷烃、多环芳烃、氯苯、醇类等均具有较好的分离效果.     

气相色谱柱对多溴联苯醚分析的影响

基于气相色谱-电子捕获检测器法对11种代表性多溴联苯醚进行分析,考察不同类型气相色谱柱对多溴联苯醚分离分析的影响. 结果表明:色谱柱极性是影响分离和响应的主要因素,极性较大的固定相上多溴联苯醚各单体的保留时间变长,响应降低,尤其是高取代多溴联苯醚的响应受到的影响最大. 柱长较短、液膜较薄的色谱柱有助于高取代多溴联苯醚的分析. 不同品牌的色谱柱受生产工艺的影响,对多溴联苯醚的响应产生较大影响.     

移动子窗口搜索法在紫丁香挥发油气相色谱-质谱分析中的应用

基于气相色谱-质谱仪产生的二维数据，采用移动子窗口搜索法，以纯组分峰为标准对同一样品在不同色谱柱上或不同样品在相同色谱柱上所获得的总离子流图的一定保留时间范围内搜索，可以得到目标化合物的流出区域，取其中点作为保留时间，从而计算各化合物在不同极性色谱柱上的程序升温保留指数。采用GC-MS与色谱保留指数相结合的方法，分别在HP-5MS和DB-35MS柱上，于80℃～290℃（4℃／min）的升温程序下，对黑龙江产紫丁香花蕾与花挥发油的分析结果表明，辅以化学计量学方法和双柱色谱保留指数定性比单用GC-MS定性结果更加快速可靠。     

阴离子交换色谱柱保留特性的变化规律及应对措施

选择对二甲苯氧化体系的高效液相色谱分析为研究对象,详细考察了阴离子交换色谱柱保留特性的变化,在整个色谱柱寿命期间(进样超过1 000次),全程采集了保留时间、分离度等数据.在此基础上,得出色谱柱保留特性的变化规律,并提出了相应的应对措施,把整个色谱柱寿命分成3个阶段,分别采用不同条件的流动相.     

有机聚合物固定相的色谱性能

研究了五种有机聚合物固定相的色谱性能.选择在170℃柱温下测定其极性常数,并以下式计算各种填料的极性常数:X′=Ix-653,Y′=Iy-590,Z′=Iz-627,U′=Iu-652,S′=Is-699.式中Ix、Iy、Iz、Iu、Is分别为柱温170℃测得的5种表征物质的保留指数,同时以实验验证了该方法的有效性和实用性.还测定了这些固定相在高纯氮气和空气中的热分析(TG、DTA)曲线,研究了DTA曲线产生峰值的原因,指出了其上限使用温度.扩展了此类固定相的应用范围.此外,还对保留值与柱温的关系进行了研究.     

丙基脲硅胶毛细管整体柱的制备及性能研究

采用溶胶-凝胶技术在毛细管中原位合成硅胶整体柱,通过表面化学修饰技术制备了极性的丙基脲硅胶整体柱.对所制备的整体柱柱性能进行了评价,考察了极性物质在该整体柱上的保留行为,并对其可能的保留机理进行了探讨.研究表明,该柱在亲水作用电色谱模式下能有效分离苯酚类极性小分子化合物.     

双色谱柱双检测器气相色谱法测定家装室内空气中8种常见苯系物的含量

为解决以单色谱柱单检测器气相色谱法测定家装室内空气中苯系物含量时易出现假阳性结果以及间二甲苯和对二甲苯难分离等问题,提出了题示方法。将活性炭吸附管两端与采样器相连,以1 L·min^-1流量采集家装室内空气样品30 min,采集30 L气体后取下活性炭吸附管,用聚四氟乙烯帽密封。取出活性炭吸附管中的活性炭,加入1.00 mL二硫化碳,于室温解吸30 min,所得溶液在柱流量1.5 mL·min^-1、分流比1∶5条件下进入气相色谱仪,苯、甲苯、乙苯、邻二甲苯、间二甲苯、对二甲苯、苯乙烯和4-叔丁基甲苯等8种常见苯系物分别经过CP-Wax强极性毛细管色谱柱(30 m×0.32 mm, 0.25μm)和DB-5弱极性毛细管色谱柱(30 m×0.25 mm, 0.25μm)分离后,用双氢火焰离子化检测器分别测定。结果显示：8种苯系物的质量浓度均在0.1～20.0 mg·L^-1内与对应的峰面积呈线性关系,检出限(3.143s)为0.000 3～0.000 5 mg·m^-3。对阴性样品进行3个浓度水平的加标回收试...     

Serially coupled capillary columns supercritical fluid chromatography with a coupling restrictor.

A serially coupled column system for capillary supercritical fluid chromatography was constructed by connecting two capillary columns of different polarities using or without using a coupling restrictor. The influence of the column sequence, the size of the coupling restrictor and the column temperature on the polarity of the system were studied. The system without a coupling restrictor (the directly coupled system) provided an intermediate polarity between two columns, depending on the column geometry, such as the film thickness and column length, although it slightly shifted to that of the first column. In the system with a coupling restrictor, the contribution of the second column to the overall retention increased with its resistance. The use of a coupling restrictor allowed to control the polarity of the coupled system virtually over the whole range between two columns. The temperature was an additional effective parameter for tuning the polarity of the system.     

Prediction of retention times and efficiency in linear gradient programmed pressure analysis on capillary columns

A method for the prediction of the retention time and the resolution of chromatographic peaks in different experimental conditions by starting from few experimental data measured in isothermal and isobaric analyses was published previously. In this paper, the same mathematical model was implemented for calculating the retention times and the column efficiency in programmed pressure runs. Some models originated from the Golay equation and reported in the literature are compared, and a new modified equation for the calculation of the peak width at half height is proposed. The procedure for the prediction of the retention time and the peak width at half height at programmed pressure of the carrier gas and different column temperature and linear gradient by using retention data of different compounds obtained in few isobaric runs is described. The prediction of the retention time and the separation efficiency of compounds with different polarity gave good results for the programmed pressure runs with linear gradient. The effect of the variation of the initial parameters of the experimental analyses and of the mathematical model on the accuracy of the prediction has been evaluated.     

Prediction of the resolution of capillary columns in different conditions of inlet pressure and temperature

A procedure previously described for the prediction of the plate height of capillary columns operated at different inlet pressure of the carrier gas and at various column temperatures by using few retention data measured under isobaric conditions was modified and improved in order to permit the prediction of the retention times and of the peak widths at various heights. It is therefore possible to calculate the ratio, delta, between the peak width at different heights and the peak width at half height, whose value is used to predict the resolution at different height of two closely eluting peaks. It was found that the delta values do not depend on temperature and inlet pressure and are a characteristic of the used column; they can therefore be used in order to calculate the resolution in any temperature and inlet pressure condition. The method was used to predict the retention time, the peak width and the resolution of polar and non-polar compounds (alkanes, alkenes, chloroalkanes, alcohols, ketones) on capillary columns of different length and polarity by using as the starting data retention and width values measured in three isobaric runs only.     

高效阴离子交换色谱-积分脉冲安培检测法分析糖类化合物影响因素的研究

研究了高效阴离子交换色谱-积分脉冲安培检测法分离测定糖类化合物的一些影响因素。这些因素包括NaOH淋洗液浓度、色谱柱温度和积分脉冲安培检测的采样电位。实验用AminoPac PA10阴离子交换柱分离糖类化合物。当NaOH淋洗液浓度增大时,糖类化合物的保留值减小,并有洗脱顺序的变化。糖的保留只表现为放热行为,但是每种糖的保留受温度的影响程度不同,即当温度改变时每种糖保留时间的变化程度不同。一般规律是随糖分子增大(依单糖、双糖、三糖、四糖顺序),其保留时间的变化程度增大。通过改变温度可以改善两种相近洗脱糖之间的分离状况。糖的范特霍夫(Van’t Hoff)曲线具有良好的线性关系。积分脉冲安培检测的采样电位增大,糖检测的峰面积增大。通过提高采样电位,可以改善糖的检测。     

The selectivity and polarity of carbon layer open tubular capillary columns modified with a polar liquid phase

The polarity of carbon layer open tubular (CLOT) columns coated with a layer of non-porous graphitized carbon black (Carbopack B) modified with an appropriate amount of polar polyglycol liquid phase has been evaluated and compared with that of standard polar (Supelcowax-10) and non-polar (SPB-1) bonded phase open tubular columns. The efficiency and selectivity were measured at various temperatures and the polarity of the columns was evaluated by use of McReynolds' constants and the difference in apparent carbon number, ΔC of linear alkanes and alcohols. The polarity of the CLOT column was found to depend on temperature, and changing the analytical conditions therefore enabled the separation of compounds of different polarity whose reciprocal position and resolution were affected by temperature. The application of calculation methods which enable programmed temperature retention times to be predicted from isothermal data was also found to be possible when the polarity of the CLOT column changes with temperature.     

Prediction of the plate height of capillary columns operated at any inlet pressure of the carrier gas by using few retention data measured under isobaric conditions

Programming inlet pressure in gas chromatography permits to decrease the analysis time without changing the elution order of compounds of different polarity whose relative retention changes with changing temperature. The choice of the best values of the inlet pressure and flow-rate of the carrier gas often requires many preliminary analyses with different parameters to be carried out. A method for the prediction of the separation by starting from few experimental data measured in isothermal and isobaric conditions decreases the time required for the optimisation of the analysis. The efficiency of the separation depends on the change of the theoretical plate height at various pressures and temperatures, due to pressure drop along the column. By calculation of the diffusion coefficients of the analysed compounds into the mobile and stationary phase it is possible to evaluate the column efficiency and predict the number of theoretical plates at any inlet pressure. A procedure for the prediction of the plate height of a capillary column at any inlet pressure of the carrier gas and column temperature by using retention data of polar and non-polar compounds (1-alcohols and linear alkanes) obtained in few isobaric runs is described.     

含酯基多孔聚合物小球色谱固定相

合成了PM和PA两个系列甲基丙烯酸甲酯或丙烯酸甲酯与二乙烯苯的多孔聚合物,测定了它们的物理、化学性能和气相色谱性能,并评价其极性。通过实例说明它们对各种混合物的分离情况;保留时间较短,柱温较低,选择性较高,性能优于PorapakT或其它极性相近的商品聚合物固定相。     

Practical aspects of the dependence of polarity on temperature

Summary It is not commonly appreciated that retention indices are temperature dependent. It is even less common to express this fact in more practical terms by saying that polarity is temperature dependent. Although the meaning of both statements is identical, we believe the second to be particularly relevant, since the majority of practical gas chromatographers tends to handle polarity as an invariable characteristic of a stationary phase.The variability of polarity with temperature is the major source of inadequate reproducibility of exact finger-printing, this particularly when gc/ms traces have to be compared to those obtained by pure gc. On the other hand, the temperature dependence provides a practical means to optimize the polarity of a given column for a given analysis. Film thickness is an essential parameter in this context because of its influence on column temperature and, therefore, on column polarity.