PtCo/Au nanocomposite: Synthesis,characterization, and magnetic properties

Magnetic PtCo/Au nanocomposites with narrow size distribution were synthesized in a reverse micelle, followed by a post-synthesis handling of the stabilizer-exchange technique. The PtCo/Au nanocomposites were characterized by ultraviolet visible spectroscopy, X-ray diffraction and transmission electron microscopy, respectively. Superconducting quantum interference device studies revealed that the nanocomposites were superparamagnetic above the blocking temperature (T_B=69 K), while the samples were ferromagnetic with Hc (628 Oe) and Ms (2.97 emu/g) at 5 K.     

Spray pyrolyzed NiO–C nanocomposite as an anode material for the lithium-ion battery with enhanced capacity retention

NiO–C nanocomposite was prepared by a spray pyrolysis method using a mixture of Ni(NO₃)₂ and citric acid solution at 600 °C. The microstructure and morphology of the NiO–C composite were characterized by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS) mapping, and thermogravimetric analysis (TGA). The results showed that the NiO nanoparticles were surrounded by amorphous carbon. Electrochemical tests demonstrated that the NiO–C nanocomposites exhibited better capacity retention (382 mAh g^− 1 for 50 cycles) than that of pure NiO (141 mAh g^− 1 for 50 cycles), which was also prepared by spray pyrolysis using only Ni(NO₃)₂ as precursor. The enhanced capacity retention can be mainly attributed to the NiO–C composite structure, composed of NiO nanoparticles surrounded by carbon, which can accommodate the volume changes during charge–discharge and improve the electrical conductivity between the NiO nanoparticles.     

Study of Schottky contact between Au and NiO nanowire by conductive atomic force microscopy (C-AFM): The case of surface states

In this work, NiO nanowires have been synthesized by a hydrothermal reaction of NiCl₂ with Na₂C₂O₄ in the presence of ethylene glycol at 180 °C for 12 h, then calcinated at 400 °C for 2 h. The NiO nanowires were analyzed by means of scanning electron microscope (SEM), atomic force microscope (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The resulting current–voltage (I–V) characteristics of the NiO nanowires exhibited a clear rectifying behavior. This rectify behavior was attributed to the formation of a Schottky contact between Au coated atomic force microscopy (AFM) tip and NiO nanowires (nano-M/SC) which was dominated by the surface states in NiO itself. Photo-assisted conductive AFM (PC-AFM) was used to demonstrate how the I–V characteristics are influenced by the surface states. Our I–V results also showed that the nano-M/SCs had a good photoelectric switching effect at reverse bias.     

Enhanced sonocatalytic degradation of organic dyes from aqueous solutions by novel synthesis of mesoporous Fe3O4-graphene/ZnO@SiO2 nanocomposites

Fe₃O₄-graphene/ZnO@mesoporous-SiO₂ (MGZ@SiO₂) nanocomposites was synthesized via a simple one pot hydrothermal method. The as-obtained samples were investigated using various techniques, as follows: scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and specific surface area (BET) vibrating sample magnetometer (VSM), among others. The sonocatalytic activities of the catalysts were tested according to the oxidation for the removal of methylene blue (MB), methyl orange (MO), and rhodamine B (RhB) under ultrasonic irradiation. The optimal conditions including the irradiation time, pH, dye concentration, catalyst dosage, and ultrasonic intensity are 60 min, 11, 50 mg/L, 1.00 g/L, and 40 W/m², respectively. The MGZ@SiO₂ showed the higher enhanced sonocatalytic degradation from among the three dyes; furthermore, the sonocatalytic-degradation mechanism is discussed. This study shows that the MGZ@SiO₂ can be applied as a novel-design catalyst for the removal of organic pollutants from aqueous solutions.     

Interface reaction of Ta/NiO and its effect on exchange coupling

Ta/NiO/NiFe/Ta multilayers, utilizing Ta as the buffer layer, were prepared by RF reactive and DC magnetron sputtering. The exchange coupling field between NiO and NiFe reached a maximum value of 120 Oe at a NiO film thickness of 50 nm. The composition and chemical state at the interface region of Ta/NiO/Ta were studied using the X-ray photoelectron spectroscopy (XPS) and peak decomposition technique. The results show that there is an `intermixing layer’ at the Ta/NiO (and NiO/Ta) interface due to a thermodynamically favorable reaction: 2Ta+5NiO=5Ni+Ta<sub>2</sub>O<sub>5</sub>. This interface reaction has an effect on the exchange coupling. The thickness of the `intermixing layer’ as estimated by XPS depth-profiles was about 8–10 nm.     

Sonochemical fabrication of gold nanoparticles–boron nitride sheets nanocomposites for enzymeless hydrogen peroxide detection

A simple sonochemical route was developed for the preparation of gold nanoparticles/boron nitride sheets (AuNPs/BNS) nanocomposites without using reducing or stabilizing agents. Transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and UV–vis absorption spectra were used to characterize the structure and morphology of the nanocomposites. The experimental results showed that AuNPs with approximately 20 nm were uniformly attached onto the BNS surface. It was found that the AuNPs/BNS nanocomposites exhibited good catalytic activity for the reduction of H₂O₂. The modified electrochemical sensor showed a linear range from 0.04 to 50 mM with a detection limit of 8.3 μM at a signal-to-noise ratio of 3. The findings provide a low-cost approach to the production of stable aqueous dispersions of nanoparticles/BNS nanocomposites.     

Template-free sonochemical synthesis of hierarchically porous NiO microsphere

A novel template-free sonochemical synthesis technique was used to prepare NiO microspheres combined with calcination of NiO_2.45C_0.74N_0.25H_2.90 precursor at 500 °C. The NiO microspheres samples were systematically investigated by the thermograviometric/differential scanning calorimetry (TG/DSC), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), fourier-transformed infrared spectroscopy (FT-IR), Brunnauer–Emmett–Teller (BET) nitrogen adsorption–desorption isotherms, laser particle size analyzer, and ultraviolet–visible spectroscopy (UV–Vis). The morphology of the precursor was retained even after the calcination process, and exhibited hierarchically porous sphericity. The morphology changed over the ultrasonic radiation time, and the shortest reaction time was 70 min, which was much less than 4 h for the mechanical stirring process. The mechanical stirring was difficult to form the complete hierarchically porous microsphere structure. The BET specific surface area and the median diameter of the hierarchically porous NiO microspheres were 103.20 m²/g and 3.436 μm, respectively. The synthesized NiO microspheres were mesoporous materials with a high fraction of macropores. The pores were resulted from the intergranular accumulation. The ultraviolet absorption spectrum showed a broad emission at the center of 475 nm, and the band gap energy was estimated to be 3.63 eV.     

Photoelectrochromic properties of NiO film deposited on an N-doped TiO2 photocatalytical layer

N-doped TiO₂ film was synthesized on indium–tin oxide (ITO) conducting glass substrate by the hydrolysis method and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Then high porous NiO was deposited onto the TiO_2?xN_x layer by chemical bath deposition (CBD) to prepare a double-layer TiO_2?xN_x/NiO electrode. The photoelectrochromic properties of the TiO_2?xN_x/NiO electrode were discussed through the results of UV–vis transmittance spectra, cyclic voltammogram and photocurrent transient measurements. It was found that the TiO_2?xN_x/NiO electrode was sensitive to light and exhibited a noticeable photoelectrochromism. The NiO film changed its color from colorless to brown, and the transmittance varied from 86.8% to 14.5% at 500 nm after 1 h irradiation.     

Fe3O4/hydroxyapatite/graphene quantum dots as a novel nano-sorbent for preconcentration of copper residue in Thai food ingredients: Optimization of ultrasound-assisted magnetic solid phase extraction

Fe₃O₄/hydroxyapatite/graphene quantum dots (Fe₃O₄/HAP/GQDs) nanocomposite was synthesized and used as a novel magnetic adsorbent. This nanocomposite was characterized using scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, energy dispersive X-ray spectroscopy, and magnetization property. The Fe₃O₄/HAP/GQDs was applied to pre-concentrate copper residues in Thai food ingredients (so-called “Tom Yum Kung”) prior to determination by inductively coupled plasma-atomic emission spectrometry. Based on ultrasound-assisted extraction optimization, various parameters affecting the magnetic solid-phase extraction, such as solution pH, amount of magnetic nanoparticles, adsorption and desorption time, and type of elution solvent and its concentration were evaluated. Under optimal conditions, the linear range was 0.05–1500 ng mL⁻¹ (R² > 0.999), limit of detection was 0.58 ng mL⁻¹, and limit of quantification was 1.94 ng mL⁻¹. The precision, expressed as the relative standard deviation of the calibration curve slope (n = 5), for intra-day and inter-day analyses was 0.87% and 4.47%, respectively. The recovery study of Cu for real samples was ranged between 83.5% and 104.8%. This approach gave the enrichment factor of 39.2, which guarantees trace analysis of Cu residues. Therefore, Fe₃O₄/HAP/GQDs can be a potential and suitable candidate for the pre-concentration and separation of Cu from food samples. It can easily be reused after treatment with deionized water.     

SnO2-decorated multiwalled carbon nanotubes and Vulcan carbon through a sonochemical approach for supercapacitor applications

Multiwalled carbon nanotubes (MWCNTs) and Vulcan carbon (VC) decorated with SnO₂ nanoparticles were synthesized using a facile and versatile sonochemical procedure. The as-prepared nanocomposites were characterized by means of transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infra red spectroscopy. It was evidenced that SnO₂ nanoparticles were uniformly distributed on both carbon surfaces, tightly decorating the MWCNTs and VC. The electrochemical performance of the nanocomposites was evaluated by cyclic voltammetry and galvanostatic charge/discharge cycling. The as-synthesized SnO₂/MWCNTs nanocomposites show a higher capacity than the SnO₂/VC nanocomposites. Concretely, the SnO₂/MWCNTs electrodes exhibit a specific capacitance of 133.33 F g⁻¹, whereas SnO₂/VC electrodes exhibit a specific capacitance of 112.14 F g⁻¹ measured at 0.5 mA cm⁻² in 1 M Na₂SO₄.     

Synthesis of Co nanocapsules coated with BN layers by annealing of KBH4 and [Co(NH3)6]Cl3

Cobalt (Co) nanocapsules coated with boron nitride (BN) layers were synthesized by annealing of ammine complex. KBH₄ and [Co(NH₃)₆]Cl₃ were used as starting materials, and annealed these powders at 500–1000 °C with flowing nitrogen gas. Formation of fcc-Co nanocapsules coated with BN layers was observed from X-ray diffraction patterns and high-resolution electron microscopy. Particle size of fcc-Co prepared at 1000 °C with flowing 100 sccm N₂ gas was approximately 40 nm, and the values of saturation magnetization and coercivity were 74.5 emu/g and 88 Oe, respectively. Good oxidation- and wear-resistances were obtained by encapsulating Co nanoparticles with BN layers.     

Structure,magnetic and microwave properties of FeNi invar nanoparticles obtained by electrical explosion of wire in different preparation conditions

Magnetic nanoparticles (MNPs) of close to invar (Fe_0.635Ni_0.365) composition were prepared by the electrical explosion of wire using different conditions to insure different values of overheating rates. X-ray diffraction, transmission electron microscopy, low temperature nitrogen adsorption, magnetic and microwave measurements were used for the characterization of MNPs. Increase of the energy injected into the wire led to increase of the specific surface (S_sp) of the produced MNPs from 4.6 to 13.5 m²/g. The fabricated MNPs were spherical and weakly aggregated with the average weighted diameter in the range of 54–160 nm depending on the S_sp. The phase composition of FeNi MNPs consists of two solid solutions of Ni in α-phase and γ-phase lattices. The increase of the energy injected into the wire leads to increase of the α-phase from 5 to 10 wt% as the injected energy raised from 0.8 to 2.5 times the sublimation energies of the wire material. Comparative analysis of structure magnetic and microwave properties showed that the obtained MNPs are important magnetic materials with high saturation magnetization and significant zero field microwave absorption which can be expected to lead to important technological applications.     

A wet-chemical route for the preparation of Ni–BaCe0.9Y0.1O3 − δ cermet anodes for IT-SOFCs

Nano-sized BaCe_0.9Y_0.1O_3 ? δ (BCY10) protonic conductor powders were used to prepare Ni-BCY10 cermets for anode-supported intermediate temperature solid oxide fuel cells. A new wet-chemical route was developed starting from Ni nitrates as precursors for NiO. BCY10 powders were suspended in a Ni nitrate aqueous solution that was evaporated to allow NiO precipitation on the BCY grains, obtaining NiO-BCY10 cermets. To obtain the final Ni-BCY10 anodes, pellets were reduced in dry H₂ at 700 °C. The structural and microstructural properties of the pellets were investigated using X-ray diffraction analysis and field emission scanning electron microscopy. A homogeneous dispersion of perovskite and nickel phases was observed. The chemical stability of the anodes was evaluated under wet H₂ and CO₂ atmosphere at 700 °C. The electrical properties of the Ni-BCY10 pellets were evaluated using electrochemical impedance spectroscopy measurements. The Ni-BCY10 cermet electrodes showed large electronic conductivity, demonstrating percolation through the Ni particles, and low area specific resistance at the BCY10 interface. These characteristics make the cermet suitable for application in BCY-based protonic fuel cells. The developed chemical route offers a simple and low-cost procedure to obtain promising high performance anodes.     

Photocatalytic reduction of carbon dioxide with water using InNbO4 catalyst with NiO and Co3O4 cocatalysts

InNbO₄ was prepared by the solid-state reaction method. Various cocatalysts were added on InNbO₄ by the incipient-wetness impregnation method. The effects of co-catalyst and pretreatment conditions on the photocatalytic activity of InNbO₄ for photoreduction of carbon dioxide were investigated. NiO–InNbO₄ and Co₃O₄–InNbO₄ were pretreated by reduction at 500 °C for 2 h and subsequent oxidation at 200 °C for 1 h. The catalysts were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and UV–vis diffuse reflectance spectroscopy. The characterization results of NiO–InNbO₄ catalysts after pretreatment showed the presence of highly crystalline NiO and monoclinic Nb₂O₅. NiO–InNbO₄ with reduction–oxidation pretreatment exhibited the highest activity due to the presence of core–shell type Ni⁰ and NiO on the surface and the presence of a small amount of Nb₂O₅ as a promoter.     

Ultrasonic assisted synthesis,characterization and influence factors of monodispersed dumbbell-like YF3 nanostructures

In the present paper, we reported the successful synthesis of dumbbell-like YF₃ nanostructures with a high yield in a mixed system of water/N,N-dimethylformamide (DMF) under the assistance of ultrasound waves of 40 kHz with the ultrasonic power of 100% (200 W) at 65 °C for 2 h, employing Y₂O₃ (99.99%) and NH₄F as the starting reactants. The product was characterized by means of powder X-ray diffraction (XRD), energy dispersive spectrometry (EDS), transmission electron microscopy (TEM), selected area electron diffraction (SAED) pattern and field-emission scanning electron microscopy (SEM). Some factors influencing the morphology of YF₃ nanostructures, including the ultrasonic time and power, the amount of NH₄F, and the ratio of water/DMF, were systematically investigated. Research showed that the morphology of YF₃ could be tuned by the volume ratio of water/DMF. The roles of DMF and the ultrasonic wave in the formation of YF₃ nanostructures were discussed.     

Microstructure characterization of mechanosynthesized nanocrystalline NiFe2O4 by Rietveld's analysis

Nanocrystalline nickel ferrite (NiFe₂O₄) is synthesized at room temperature by high-energy ball milling the stoichiometric mixture of (1:1 mol%) of NiO and α-Fe₂O₃ powders. The structural and microstructural evolution of NiFe₂O₄ caused by milling is investigated by X-ray powder diffraction. The relative phase abundance, particle size, r.m.s. strain, lattice parameter changes of different phases have been estimated employing Rietveld structure refinement analysis of X-ray powder diffraction data. Particle size and content (wt%) of both NiO and α-Fe₂O₃ phases reduce rapidly with increasing milling time and a significant amount of nanocrystalline NiFe₂O₄ is formed within 1 h of ball milling. Particle sizes of all the phases reduce to ∼10 nm within 5 h of milling and remain almost unchanged with increasing milling time up to 20 h. Lattice parameter of cubic NiO decreases linearly with increasing milling time, following the Vegard's law of solid-solution alloy. A continuous decrease in lattice parameter of cubic NiFe₂O₄ phase clearly suggests that smaller Ni atoms have occupied some of the vacant oxygen sites of ferrite lattice. Cation distribution both in octahedral and tetrahedral sites changes continuously with milling time and the normal spinel lattice formed at early stage of milling, transforms to inverse spinel lattice in the course of milling. High-resolution transmission electron microscope (HRTEM) micrographs of 11 h milled sample corroborates the findings of X-ray profile analysis.     

Synthesis and characterization of a new nano lead(II) 0-D coordination supramolecular compound: A precursor to produce pure phase nano-sized lead(II) oxide

Nano-structure of a new 0D Pb(II) coordination supramolecular compound, [Pb₄(8-Quin)₆](ClO₄)₂(1), L = 8-HQuin = 8-hydroxyquinolin ligand has been synthesized by use of a sonochemical process and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRPD), Fourier transform infrared spectroscopy (FTIR) and elemental analyses. The structure of compound 1 was determined by single-crystal X-ray diffraction. The single crystal X-ray data of compound 1 implies that the Pb⁺² ions are five coordinated. Each lead atom is coordinated to nitrogen and oxygen atoms of 8-hydroxyquinolin ligand. Topological analysis shows that the compound 1 is 1,2,3,4,4M12-1net. Nanoparticles of lead(II) oxide have been prepared by calcination of lead(II) coordination polymer at 500 °C that were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRPD) and IR spectroscopy.     

Magnetic properties of iron nanoparticles in a polymer film

We systematically synthesized self-aggregated iron nanoparticles in the perfluorinated sulfo-cation membrane (MF-4SK) by ion-exchange method. Our experimental results show that iron nanoparticles in MF-4SK exhibit superparamagnetic properties above the blocking temperature. Field-cooled and zero-field-cooled magnetization data show the blocking temperature, T_B≅120 K for the iron concentration of 5×10¹⁹ atoms per 1 g of polymer film at 500 Oe applied field. This result is well matched with the calculation based on the temperature dependence of the coercivity, which shows T_B≅110 K, with the zero temperature coercivity (H_C0) ≅ 420 Oe. The radius of the typical iron particle is determined to be ∼2 nm from transmission electron microscopy (TEM), showing good agreement with the value acquired by Langevin function fit. These experimental evidences suggest that iron nanoparticles in the polymer film obey a single-domain theory.     

Synthesis and characterization of spinel type high-power cathode materials Li MxMn2−x O4 (M=Ni,Co, Cr)

The transition metal-doped spinel cathode materials, LiM_0.5Mn_1.5O₄ (M=Ni. Co, Cr) were prepared by solid-state reaction. The structure and morphology of the samples were investigated by X-ray diffraction, Rietveld refinement and scanning electron microscopy (SEM). The diffraction peaks of all the samples corresponded to a single phase of cubic spinel structure with a space group Fd3m. Field-emission SEM shows octahedron like shapes and the primary particles size was between 500 nm and 2 μm. Oxidation states of Ni, Co and Cr were found to be 2+, 2+ and 3+ as revealed by X-ray photoelectron spectroscopy. During discharging, LiNi_0.5Mn_1.5O₄ and LiCo_0.5Mn_1.5O₄ sample shows more than 130 mAh/g between 3.5 and 5.2 V at a current density of 0.65 mA/cm² and well developed plateau around 5 V, respectively.     

Preparation of magnetic FeCo nanoparticles by coprecipitation route

Magnetic FeCo nanoparticles with high saturation magnetization (M_s = 148 emu/g) at 15 kOe were prepared by a coprecipitation route. The value of M_s for FeCo nanoparticles depends on the ratio of Fe to Co components. The size of the nanoparticles was confirmed by transmission electron microscopy (TEM) images, and morphology of the nanoparticles was obtained by field emission scanning electron microscopy (FE-SEM) images. The crystal structure of the nanoparticles dependent on annealing was characterized by X-ray diffraction data. The magnetic properties were characterized by saturation magnetization from a hysteresis loop by VSM.