Thermodynamic properties of tert-butylbenzene and 1,4-di-tert-butylbenzene

Heat capacities, enthalpies of phase transitions, and derived thermodynamic properties over the temperature range 5 < (T/K) < 442 were determined with adiabatic calorimetry for tert-butylbenzene (TBB) {Chemical Abstracts Service registry number (CASRN) [98-06-6]} and 1,4-di-tert-butylbenzene (DTBB) {CASRN [1012-72-2]}. A crystal to plastic crystal transition very near the triple-point temperature of DTBB was observed. New vapor pressures near the triple-point temperature are also reported for DTBB for the liquid and crystal states. These new measurements, when combined with published results, allow calculation of the thermodynamic properties for the ideal gas state for both compounds. The contribution of the tert-butyl group to the entropy of the ideal gas is determined quantitatively here for the first time based on the calorimetric results over the temperature range 298.15 < (T/K) < 600. Comparisons with literature values are shown for all measured and derived properties, including entropies for the ideal gas derived from quantum chemical calculations.     

Experimental and computational study of the thermodynamic properties of 2-nitrofluorene and 2-aminofluorene

This report presents a comprehensive experimental and computational study of the thermodynamic properties of two fluorene derivatives: 2-aminofluorene and 2-nitrofluorene. The standard (p° = 0.1 MPa) molar enthalpies of formation in the crystalline phase of these compounds were derived from the standard molar energies of combustion, in oxygen, at T = 298.15 K, measured by static bomb combustion calorimetry. A Knudsen effusion method was used to perform the vapour pressure study of the referred compounds, yielding an accurate determination of the standard molar enthalpies and entropies of sublimation. The enthalpies of sublimation were also determined using Calvet microcalorimetry and the enthalpy and temperature of fusion were derived from DSC experiments. Derived results of standard enthalpy and Gibbs energy of formation in both gaseous and crystalline phases were compared with the ones reported in literature for fluorene. A theoretical study at the G3 and G4 levels has been carried out, and the calculated enthalpies of formation have been compared to the experimental values.     

Thermochemical properties of 4-N,N-dialkylamino-7-nitrobenzofurazan derivatives (alkyl = methyl,ethyl)

The standard (p° = 0.1 MPa) molar enthalpies of formation, at T = 298.15 K, in the gaseous phase, for two nitrobenzofurazan derivatives, 4-N,N-dimethylamino-7-nitrobenzofurazan (DMANBF) and 4-N,N-diethylamino-7-nitrobenzofurazan (DEANBF), were derived from their enthalpies of combustion and sublimation, obtained by static bomb calorimetry and by the Knudsen effusion technique, respectively. The results are compared with the corresponding data calculated by the G3(MP2)//B3LYP approach. Computationally, the molecular structures of both compounds were established and the geometrical parameters were determined at the B3LYP/6-31G(d) level of theory.     

Thermodynamic properties of 4-tert-butyl-diphenyl oxide

The main thermodynamic functions (changes of the entropy, enthalpy, and Gibbs free energy) and functions of formation at T = 298.15 K of 4-tert-butyl-diphenyl oxide in condensed and ideal gas states were computed on the basis of experimental results obtained. The heat capacities of 4-tert-butyl-diphenyl oxide was measured by vacuum adiabatic calorimetry over the temperature range (8 to 371) K. The temperature, the enthalpy and the entropy of fusion were determined. The energy of combustion of the sample was determined by static-bomb combustion calorimetry. The saturation vapor pressures of the substance were measured by dynamic transpiration method over the temperature and pressure intervals (298 to 325) K and (0.05 to 1.2) Pa. The enthalpy of sublimation at T = 298.15 K was derived. The contribution of O-(2C_b) group (where C_b is the carbon atom in a benzene ring) into the absolute entropies of diphenyl oxide derivatives was assessed.     

Thermochemistry of uracil and thymine revisited

Thermochemical properties of uracil and thymine have been evaluated using additional experiments. Standard (p⁰ = 0.1 MPa) molar enthalpies of formation in the gas phase at T = 298.15 K for uracil −(298.1 ± 0.6) and for thymine −(337.6 ± 0.9) kJ · mol⁻¹ have been derived from energies of combustion measured by static bomb combustion calorimetry and molar enthalpies of sublimation determined using the transpiration method. The G3 and G4 quantum-chemical methods were used for calculations of theoretical gaseous enthalpies of formation being in very good agreement with the re-measured experimental values.     

Thermodynamic properties of bromine fluorene derivatives: An experimental and computational study

This report presents a comprehensive experimental and computational study of the thermodynamic properties of two bromine fluorene derivatives: 2-bromofluorene and 2,7-dibromofluorene. The standard (p° = 0.1 MPa) molar enthalpies of formation in the crystalline phase of these compounds were derived from the standard molar energies of combustion, in oxygen, at T = 298.15 K, measured by rotating bomb combustion calorimetry. The vapour pressures of the crystalline phase of the two compounds were measured using the Knudsen effusion method and a static method that has also been used to measure the liquid vapour pressures of 2-bromofluorene. From these results the standard molar enthalpies, entropies and Gibbs energies of sublimation of the two compounds studied and of vapourisation of 2-bromofluorene were derived. The enthalpies and temperatures of fusion were determined from DSC experiments. Derived results of standard enthalpies and Gibbs energies of formation, in both gaseous and crystalline phases, were compared with the ones reported in the literature for fluorene.The experimental values of the gas-phase enthalpies of formation of each compound were compared with estimates based on density functional theory calculations using the B3LYP hybrid exchange–correlation energy functional with the 6-311++G(d,p) basis set.     

The heat capacities and thermodynamic functions of some derivatives of ferrocene

The heat capacities of benzoylferrocene (BOF), C₅H₅FeC₅H₄COC₆H₅, and benzylferrocene (BF), C₅H₅FeC₅H₄CH₂C₆H₅, have been measured by the low-temperature adiabatic calorimetry in the temperature range from 6 K to 372 K. The purity benzylferrocene and thermodynamic properties – the triple point temperature and the enthalpy of fusion have been obtained. The ideal gas thermodynamic functions (changes of the entropy, enthalpy, and Gibbs free energy) of BOF and BF were derived at T = 298.15 K using the heat capacities and previously determined data on the saturation vapours pressures and the enthalpies of sublimation. The ideal gas enthalpy of formation and absolute entropy of BOF at T = 298.15 K have been obtained from quantum chemical calculations, where as the thermodynamic properties of BF have been estimated by empirical method of group equations. A good agreement between experimental and theoretical values provides an additional check of the reliability of the experimental data.     

Thermodynamic properties of sublimation of the ortho and meta isomers of acetoxy and acetamido benzoic acids

This paper reports vapour pressures measured at several different temperatures using the Knudsen effusion method of ortho-acetoxybenzoic acid (aspirin) (341.1 to 361.1) K, meta-acetoxybenzoic acid (344.2 to 362.2) K, ortho-acetamidobenzoic acid (367.2 to 389.2) K, and meta-acetamidobenzoic acid (423.2 to 441.1) K. The experimental results enabled the determination of the standard molar enthalpies, entropies and Gibbs energies of sublimation, at T = 298.15 K, of the four compounds studied. DSC experiments yield results of the temperature and enthalpy of fusion. The experimental results were compared with literature ones for the para isomers of the acids acetoxybenzoic and acetamidobenzoic. Correlations involving temperature of fusion, and standard molar enthalpy and Gibbs energy of sublimation of several substituted benzoic acids were proposed. Those correlation equations allow a good estimative of volatility of benzoic acid derivatives from their enthalpies of sublimation and temperatures of fusion.     

Thermodynamic properties of 1,2-dihydronaphthalene: Glassy crystals and missing entropy

Measurements leading to the calculation of the standard thermodynamic properties for gaseous 1,2-dihydronaphthalene (Chemical Abstracts registry number [447-53-0]) are reported. Experimental methods include oxygen combustion-bomb calorimetry, adiabatic heat-capacity calorimetry, vibrating-tube densitometry, comparative ebulliometry, and inclined-piston gauge manometry. 1,2-Dihydronaphthalene decomposed significantly when heated to temperatures above T = 480 K. Consequently, the critical temperature, critical pressure, and critical density were estimated. Standard molar entropies, standard molar enthalpies, and standard molar Gibbs free energies of formation were derived at selected temperatures between T = 250 K and 500 K. The standard state is defined as the ideal gas at the pressure p = p^° = 101.325 kPa. Standard entropies are compared with those calculated statistically on the basis of assigned vibrational spectra from the literature for the vapor phase. A large and near constant difference between the entropies calculated statistically and those determined calorimetrically was observed over the entire temperature range studied. Two glass-like features are observed in the heat capacity against temperature curve for the solid state, indicating that the crystals are disordered. A quantitative accounting for the entropy discrepancy is proposed based on possible molecular orientations of 1,2-dihydronaphthalene. Results are compared with experimental values reported in the literature.     

Thermochemical study of the isomeric compounds: 3-acetylbenzonitrile and benzoylacetonitrile

The standard (p° = 0.1 MPa) molar enthalpies of formation of 3-acetylbenzonitrile and benzoylacetonitrile, in the crystalline phase, were derived from the respective standard massic energies of combustion measured by static bomb combustion calorimetry, in oxygen, at T = 298.15 K. The standard molar enthalpies of sublimation, at T = 298.15 K, were measured by Calvet microcalorimetry. From the above experimentally determined enthalpic parameters, the standard molar enthalpies of formation in the gaseous phase, at T = 298.15 K, are found to be: (52.4 ± 2.1) kJ · mol⁻¹ and (74.8 ± 2.5) kJ · mol⁻¹ for 3-acetylbenzonitrile and benzoylacetonitrile, respectively.Molecular structures were computed using highly accurate ab initio techniques. Standard molar enthalpies of formation of the experimentally studied compounds were derived using an appropriate set of working reactions. Very good agreement between the calculated and the experimental values was obtained, so the calculations were extended to the estimates of the standard molar enthalpies of formation of 2- and 4-acetylbenzonitriles whose study was not performed experimentally.Our results were further interpreted and rationalized in terms of the enthalpic stability and compared to other relevant disubstituted benzenes.     

Experimental and theoretical study of thermodynamic properties of levoglucosan

The heat capacity of levoglucosan was measured over the temperature range (5 to 370) K by adiabatic calorimetry. The temperatures and enthalpies of a solid-phase transition and fusion for the compound were found by DSC. The obtained results allowed us to calculate thermodynamic properties of crystalline levoglucosan in the temperature range (0 to 384) K. The enthalpy of sublimation for the low-temperature crystal phase was found from the temperature-dependent saturated vapor pressures determined by the Knudsen effusion method. The thermodynamic properties of gaseous levoglucosan were calculated by methods of statistical thermodynamics using the molecular parameters from quantum chemical calculations. The enthalpy of formation of the crystalline compound was found from the experiments in a combustion calorimeter. The gas-phase enthalpy of formation was also obtained at the G4 level of theory. The thermodynamic analysis of equilibria of levoglucosan formation from cellulose, starch, and glucose was conducted.     

Determination of standard enthalpy of vaporization and thermal decomposition reactions from derivative thermogravimetric (DTG) curves

The paper proposes the use of the derivative thermogravimetric (DTG) curve for the acquisition of equilibrium vapor pressure and dissociation pressure for the materials and derivation of their standard enthalpy of formation from single DTG curve recorded under optimum experimental conditions, such as heating rate and the sweep rate of the carrier gas passed over the sample. The vapor pressure and the standard enthalpy of sublimation (Δ_subH ° _298.15) of CdI₂ and the dissociation pressure and the standard enthalpy of formation of CaCO₃ derived from their DTG curves are found to be in good agreement with the best assessed values reported in the literature.     

Thermodynamic properties of binary mixtures containing hydrofluoroether

Excess molar enthalpy and excess molar volume at T =  298.15 K are reported for binary mixtures of (nonafluorobutylmethylether  +  butylmethylether, or nonane, or heptane, or pentane, or 1-propanol, or 2-propoxyethanol). Excess molar enthalpies of the mixture of (nonafluorobutylmethylether  +  1-pentanol) also are reported at T =  298.15 K. The results of excess molar enthalpy are endothermic and the results of excess molar volume are positive in the whole concentration for all the mixtures. The phase separation is found in the range of 0.15  < x <  0.92 for the 1-pentanol system. The results are explained by means of the destruction of the dipolar interactions and hydrogen bonds in the component liquids, the difference of the dispersion interaction, and the formation of the intermolecular hydrogen bonds between unlike molecules.     

New experimental heat capacity and enthalpy of formation of lithium cobalt oxide

The heat capacity of LiCoO₂ (O3-phase), constituent material in cathodes for lithium-ion batteries, was measured using two differential scanning calorimeters over the temperature range from (160 to 953) K (continuous method). As an alternative, the discontinuous method was employed over the temperature range from (493 to 693) K using a third calorimeter. Based on the results obtained, the enthalpy increment of LiCoO₂ was derived from T = 298.15 K up to 974.15 K. Very good agreement was obtained between the derived enthalpy increment and our independent measurements of enthalpy increment using transposed temperature drop calorimetry at 974.15 K. In addition, values of the enthalpy of formation of LiCoO₂ from the constituent oxides and elements were assessed based on measurements of enthalpy of dissolution using high temperature oxide melt drop solution calorimetry. The high temperature values obtained by these measurements are key input data in safety analysis and optimisation of the battery management systems which accounts for possible thermal runaway events.     

Vapour pressure of diethyl phthalate

Measurements of vapour pressure in the liquid phase and of enthalpy of vaporisation and results of calculation of ideal-gas properties for diethyl phthalate are reported. The method of comparative ebulliometry, the static method, and the Knudsen mass-loss effusion method were employed to determine the vapour pressure. A Calvet-type differential microcalorimeter was used to measure the enthalpy of vaporisation. Simultaneous correlation of vapour pressure, of enthalpy of vaporisation and of difference in heat capacities of ideal gas and liquid/solid phases was used to generate parameters of the Cox equation that cover both the (vapour + solid) equilibrium (approximate temperature range from 220 K to 270 K) and (vapour + liquid) equilibrium (from 270 K to 520 K). Vapour pressure and enthalpy of vaporisation derived from the fit are reported at the triple-point temperature T = 269.92 K (p = 0.0029 Pa, Δ_vapH_m = 85.10 kJ · mol⁻¹ ), at T = 298.15 K (p = 0.099 Pa, Δ_vapH_m = 82.09 kJ · mol⁻¹), and at the normal boiling temperature T = 570.50 K (Δ_vapH_m = 56.49 kJ · mol⁻¹). Measured vapour pressures and measured and calculated enthalpies of vaporisation are compared with literature data.     

S6 Isomer of C60(CF3)12: Synthesis,properties and thermodynamic functions

A crystalline form of S₆-С₆₀(CF₃)₁₂ was synthesized in an amount sufficient for reliable experimental investigation. We determined the enthalpy of combustion of S₆-С₆₀(CF₃)₁₂ in oxygen and its heat capacity, which made possible to derive the thermodynamic functions of S₆-С₆₀(CF₃)₁₂, namely the enthalpy of formation, the entropy and the Gibbs energy at T = 298.15 K. These experimental thermochemical data enabled estimation of the formation energy for a broad range of other trifluoromethylated compounds C₆₀(CF₃)_n, with n = (2–18; 24), on the basis of their DFT calculated relative energies.     

Thermodynamic properties of 9-fluorenone: Mutual validation of experimental and computational results

Measurements leading to the calculation of thermodynamic properties for 9-fluorenone (IUPAC name 9H-fluoren-9-one and Chemical Abstracts registry number [486-25-9]) in the ideal-gas state are reported. Experimental methods were adiabatic heat-capacity calorimetry, inclined-piston manometry, comparative ebulliometry, and combustion calorimetry. Critical properties were estimated. Molar entropies for the ideal-gas state were derived from the experimental studies at selected temperatures T between T = 298.15 K and T = 600 K, and independent statistical calculations were performed based on molecular geometry optimization and vibrational frequencies calculated at the B3LYP/6 − 31 + G(d,p) level of theory. Values derived with the independent methods are shown to be in excellent accord with a scaling factor of 0.975 applied to the calculated frequencies. This same scaling factor was successfully applied in the analysis of results for other polycyclic molecules, as described in recent articles by this research group. All experimental results are compared with property values reported in the literature. Thermodynamic consistency between properties is used to show that several studies in the literature are erroneous.     

Volumetric properties and enthalpies of solution of alcohols CkH2k+1OH (k = 1, 2, 6) in 1-methyl-3-alkylimidazolium bis(trifluoromethylsulfonyl)imide {[C1CnIm][NTf2] n = 2, 4, 6, 8, 10} ionic liquids

We present a study on the effect of the alkyl chain length of the imidazolium ring in 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ionic liquids, [C₁C_nIm][NTf₂] (n = 2 to 10), on the mixing properties of (ionic liquid + alcohol) mixtures (enthalpy and volume). We have measured small excess molar volumes with highly asymmetric curves as a function of mole fraction composition (S-shape) with more negative values in the alcohol-rich regions. The excess molar volumes increase with the increase of the alkyl-chain length of the imidazolium cation of the ionic liquid. The values of the partial molar excess enthalpy and the enthalpy of mixing are positive and, for the case of methanol, do not vary monotonously with the length of the alkyl side-chain of the cation on the ionic liquid – increasing from n = 2 to 6 and then decreasing from n = 8. This non-monotonous variation is explained by a more favourable interaction of methanol with the cation head group of the ionic liquid for alkyl chains longer than eight carbon atoms. It is also observed that the mixing is less favourable for the smaller alcohols, the enthalpy of mixing decreasing to less positive values as the alkyl chain of the alcohol increases. Based on the data from this work and on the knowledge of the vapour pressure of {[C₁C_nIm][NTf₂] + alcohol} binary mixtures at T = 298 K reported in the literature, the excess Gibbs free energy, excess enthalpy and excess entropy could be then calculated and it was observed that these mixtures behave like the ones constituted by a non-associating and a non-polar component, with its solution behaviour being determined by the enthalpy.     

Calorimetric and computational study of 7-hydroxycoumarin

The standard (p° = 0.1 MPa) molar energy of combustion in oxygen, at T = 298.15 K, of 7-hydroxycoumarin was measured by static bomb calorimetry. The value of the standard molar enthalpy of sublimation was obtained by Calvet microcalorimetry and corrected to T = 298.15 K. Combining these results, the standard molar enthalpy of formation of the compound, in the gas phase, at T = 298.15 K, has been calculated, ?(337.5 ± 2.3) kJ · mol^?1. The values for the temperature of fusion, T_fusion, and for the fusion enthalpy, at T = T_fusion, are also reported.Additionally, high-level density functional theory calculations using the B3LYP hybrid exchange-correlation energy functional with extended basis sets, the MC3BB and MC3MPW methods and more accurate correlated computational techniques of the MCCM suite have been performed for the compound.The agreement between experiment and theory gives confidence to estimate the enthalpy of formation of the remaining hydroxycoumarins substituted in the benzene ring.