Henry’s constant of carbon dioxide-aqueous deep eutectic solvent (choline chloride/ethylene glycol,choline chloride/glycerol,choline chloride/malonic acid) systems

In this study, we present a new set of Henry’s constant data for the system carbon dioxide-aqueous deep eutectic solvent (DES) (20 to 80 wt% DES) at T = (303.15, 308.15, and 313.15) K. The DESs used were choline chloride-based: ethaline (choline chloride/ethylene glycol), glyceline (choline chloride/glycerol), and maline (choline chloride/malonic acid). A differential Henry’s coefficient model was used to describe the behaviour of Henry’s constant, and correlate it with temperature and concentration of DES in the aqueous DES solution. The correlation was found satisfactory such that the proposed model can be used in engineering calculations with reasonable accuracy.     

Investigation of phase equilibria of levulinic acid distribution between aqueous phase to organic phase by Aliquat 336 in different modifiers

The extraction of levulinic acid by tricaprylmethylammonium chloride (Aliquat 336) dissolved in five alcohols solvents (isoamyl alcohol, hexan-1-ol, octan-1-ol, nonan-1-ol, decan-1-ol) and five esters solvents (dimethyl phthalate, dimethyl adipate, dimethyl succinate, dimethyl glutarate, diethyl carbonate), two ketones (diisobutyl ketone (DIBK), methyl isobutyl ketone (MIBK)) were investigated to understand effect of modifier on levulinic acid extraction. In addition to these Aliquat 336 + modifier system, the experiments were done also with single solvents. All measurements were carried out T = 298.15 K. Organic solutions of Aliquat 336 are being used increasingly to separate organic acids from aqueous mixture solutions by reactive extraction. The extent to which the organic phase may be loaded with levulinic acid is explained as a loading ratio, Z_Z, extraction efficiency E and, distribution coefficients K_D were calculated. The maximum extraction efficiency was obtained value of 72.1 for isoamyl alcohol. The extraction equilibrium constant, K_E, has been calculated for each modifier. Furthermore, Freundlich, Langmuir, and LSER model equations have been obtained for experimental data of alcohols.     

The co-solubility of 2-ethylhexanoic acid and some liquid alcohols in supercritical carbon dioxide

The co-solubility in supercritical carbon dioxide of 1-butanol, 1-pentanol, 2-ethyl-1-hexanol, or 1-decanol in the presence of 2-ethylhexanoic acid in the pressure range of 100–180 bar and at 313 or 323 K was measured. The solubility of these alcohols in the presence of 2-ethylhexanoic acid is lower than in the systems alcohol + CO₂ and remains nearly constant in the pressure range of 120–180 bar, with the exception of 1-decanol. The lower selectivities in the ternary systems are explained by strong intermolecular hydrogen bonding between alcohol molecules and 2-ethylhexanoic acid molecules. The FT-IR spectra of mixtures of alcohols and 2-ethylhexanoic acid at a 1:1 mole ratio in the liquid CCl₄ confirmed this conclusion.     

Solubility and physic-chemical properties of NaH2PO4 in phosphoric acid,sodium chloride and their mixture solutions at T = (298.15 and 313.15) K

In this study, solubility and physic-chemical properties of sodium dihydrogen phosphate in sodium chloride, phosphoric acid and their mixture solutions at T = (298.15 and 313.15) K have been investigated by using isothermal dissolution method. In the three systems, the solubility of NaH₂PO₄ always increases with the temperature increasing and decreases with molar concentration of phosphoric acid (sodium chloride) increasing because of the same ion effect. Solubility data of sodium dihydrogen phosphate in the mixed solution of sodium chloride and phosphoric acid is basically required for designing and optimizing the solvent extraction process in the industrial production.     

Solubility of hydrogen in toluene for the ternary system H2 + CO2 + toluene from 305 to 343 K and 1.2 to 10.5 MPa

The solubility of hydrogen in toluene in the presence of the compressed CO₂ at the temperatures from 305 to 343 K and the pressures from 1.2 to 10.5 MPa was measured by using a continuous flow technique. The obtained data indicate that more hydrogen could be dissolved in toluene at the pressures higher than a certain value depending on temperature and the molar ratio of H₂ to CO₂ in gas. The Peng–Robinson equation of state associated with the van der Waals mixing rule were found to correlate the VLE data of the ternary system H₂ + CO₂ + toluene satisfactorily. From the volume expansion resulted from the dissolution of CO₂ in toluene calculated by the proposed model, it was found that hydrogen solubility was generally increased with increasing volume expansion. A large volume expansion was required to enhance hydrogen solubility when the mole fraction of hydrogen in gas was low.     

Phase behavior of (CO2 + methanol + lauric acid) system

In this study the phase equilibrium behaviors of the binary system (CO₂ + lauric acid) and the ternary system (CO₂ + methanol + lauric acid) were determined. The static synthetic method, using a variable-volume view cell, was employed to obtain the experimental data in the temperature range of (293 to 343) K and pressures up to 24 MPa. The mole fractions of carbon dioxide were varied according to the systems as follows: (0.7524 to 0.9955) for the binary system (CO₂ + lauric acid); (0.4616 to 0.9895) for the ternary system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (2:1); and (0.3414 to 0.9182) for the system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (6:1). For these systems (vapor + liquid), (liquid + liquid), (vapor + liquid + liquid), and (solid + fluid) transitions were observed. The phase equilibrium data obtained for the systems were modeled using the Peng–Robinson equation of state with the classical van der Waals mixing rule with a satisfactory correlation between experimental and calculated values.     

Measurement and prediction of phase behaviour for 1-alkyl-3-methylimidazolium tetrafluoroborate and carbon dioxide: Effect of alkyl chain length in imidazolium cation

The high-pressure phase behaviour of the binary system {1-ethyl-methylimidazolium tetrafluoroborate ([EMIM][BF₄]) + CO₂} was determined over the temperature range of (293.2 to 323.2) K at intervals of 5.0 K with the CO₂ mole fraction ranging from 0.153 to 0.578 by using a high-pressure variable-volume view cell. Further, the (vapour + liquid) equilibrium of the binary system {1-hexyl-methylimidazolium tetrafluoroborate ([HMIM][BF₄]) + CO₂} was measured over the temperature range of (303.2 to 328.2) K with the CO₂ mole fraction ranging from 0.314 to 0.593. The Peng–Robinson equation of state along with two-parameter mixing rules has been employed to correlate the experimental results. In case of the ([EMIM][BF₄] + CO₂) system, the (vapour + liquid + liquid) equilibrium and (vapour + liquid) equilibrium have been observed at a high CO₂ mole fraction. The experimental values obtained in this study were compared with the available phase behaviour data of the binary system (1-alkyl-3-methylimidazolium tetrafluoroborate + CO₂) in order to investigate the effect of the alkyl chain length in the imidazolium cation on the phase behaviour of such systems.     

Measurement and modeling of high-pressure (vapor + liquid) equilibria of (CO2 + alkanol) binary systems

Complementary isothermal (vapor + liquid) equilibria data are reported for the (CO₂ + 3-methyl-2-butanol), (CO₂ + 2-pentanol), and (CO₂ + 3-pentanol) binary systems at temperatures of (313, 323, and 333) K, and at pressure range of (2 to 11) MPa. For all (CO₂ + alcohol) systems, it was visually monitored that there was no liquid immiscibility at the temperatures and pressures studied. The experimental data were correlated with the Peng–Robinson equation of state using the quadratic mixing rules of van der Waals with two adjustable parameters. The calculated (vapor + liquid) equilibria compositions were found to be in good agreement with the experimental data with deviations for the mole fractions <8% and <2% for the liquid and vapor phase, respectively.     

High pressure measurement and CPA equation of state for solubility of carbon dioxide and hydrogen sulfide in 1-butyl-3-methylimidazolium acetate

Removal of acid gases such as CO₂ and H₂S from natural gas is essential for commercial, safety and environmental protection that demonstrate the importance of gas sweetening process. Ionic liquids (IL) have been highly demanded as a green solvent to remove acid gases from sour natural gas and capturing of CO₂ from flue gases. In this work, the solubility of CO₂ in 1-butyl-3-methylimidazolium acetate ([bmim][Ac]) is measured at temperatures (303.15, 328.15, 343.15) K and pressure range of (0.1 to 3.9) MPa. Moreover, the experiments are carried out for simultaneous measurements of (CO₂ + H₂S) (70% + 30% on a mole basis) solubility in the same ionic liquid at T = (303.15, 323.15, 343.15) K and a pressure range of (0.1 to 2.2) MPa. To model the solubility of acid gases in IL, both physical and chemical equilibria are applied so that the (vapour + liquid) equilibrium calculation is carried out through Cubic-Plus-Association (CPA) EoS. The reaction equilibrium thermodynamic model is used in liquid phase so that the chemical reaction is taking place between IL and acid gasses. The Henry’s and reaction equilibrium constants are obtained though optimization of the solubility data. Using CPA EOS, the pure parameters of [bmim][acetate] are optimised and consequently using these parameters, gas partial pressure calculation is performed for the (CO₂ + IL) and (CO₂ + H₂S + IL) systems. For the (CO₂ + IL) system, the percent average absolute deviation (AAD%) of 4.83 is resulted and for the (H₂S + CO₂ + IL) system the values of 18.8 and 13.7 are obtained for H₂S and CO₂, respectively.     

Gas solubility of CO2 in aqueous solutions of N-methyldiethanolamine and diethanolamine with 2-amino-2-methyl-1-propanol

Gas solubility of carbon dioxide in an aqueous solution of 32.5 wt.% N-methyldiethanolamine and 12.5 wt.% diethanolamine with 4, 6, and 10 wt.% 2-amino-2-methyl-1-propanol has been measured, at 313.15, 343.15, and 393.15 K, over a range of pressure from 3 to 2000 kPa, using a chromatographic method for analysis of the liquid phase. The results of the gas solubility are given as the partial pressure of CO₂ against its mole ratio α (mol CO₂/mol alkanolamine) and its mole fraction at each temperature studied. The solubility of CO₂ in all the systems studied decreases with an increase in temperature and increases with an increase in the partial pressure of CO₂ at a given temperature and it is a function of the concentration of the mixture of alkanolamines in solution. The enthalpy of solution of CO₂ has been calculated from the experimental solubility data.     

Phase equilibrium data and thermodynamic modeling of the system (CO2 + biodiesel + methanol) at high pressures

The main objective of this work was to investigate the high pressure phase behavior of the binary systems {CO₂(1) + methanol(2)} and {CO₂(1) + soybean methyl esters (biodiesel)(2)} and the ternary system {CO₂(1) + biodiesel(2) + methanol(3)} were determined. Biodiesel was produced from soybean oil, purified, characterized and used in this work. The static synthetic method, using a variable-volume view cell, was employed to obtain the experimental data in the temperature range of (303.15 to 343.15) K and pressures up to 21 MPa. The mole fractions of carbon dioxide were varied according to the systems as follows: (0.2383 to 0.8666) for the binary system {CO₂(1) + methanol(2)}; (0.4201 to 0.9931) for the binary system {CO₂(1) + biodiesel(2)}; (0.4864 to 0.9767) for the ternary system {CO₂(1) + biodiesel(2) + methanol(3)} with a biodiesel to methanol molar ratio of (1:3); and (0.3732 to 0.9630) for the system {CO₂ + biodiesel + methanol} with a biodiesel to methanol molar ratio of (8:1). For these systems, (vapor + liquid), (liquid + liquid), (vapor + liquid + liquid) transitions were observed. The phase equilibrium data obtained for the systems were modeled using the Peng–Robinson equation of state with the classical van der Waals (PR-vdW2) and Wong-Sandler (PR–WS) mixing rules. Both thermodynamic models were able to satisfactorily correlate the phase behavior of the systems investigated and the PR–WS presented the best performance.     

Measuring solubility of carbon dioxide in aqueous blends of N-methyldiethanolamine and 2-((2-aminoethyl)amino)ethanol at low CO2 loadings and modelling by electrolyte SAFT-HR EoS

In this work, new solubility values for CO₂ absorption in aqueous solutions of N-methyldiethanolamine (MDEA) in the presence of different mole ratios of 2-((2-aminoethyl)amino)ethanol (AEEA) at low pressures are obtained. The total molar amine concentration of all the solutions has been fixed equal to 3.360 mol · L⁻¹ (5.370 mol amine · kg⁻¹ water). The mole ratio of AEEA/MDEA was set to 0.12500, 0.10000 and 0.05000. The experimental total pressure varied from (7.3 to 386.6) kPa and the experimental temperature was set to (313.15, 328.15, 343.15 and 358.15) K. The electrolyte SAFT-HR (eSAFT-HR) equation of state (EoS) (Najafloo et al., 2014) has been successfully applied to model the solubility of CO₂ in aqueous mixtures of AEEA and MDEA. The overall average absolute relative per cent deviation (AAD%) in calculating the total pressure as a function of CO₂ loading is 7.74 for (AEEA + MDEA + CO₂ + H₂O) quaternary system at the four values of temperature. To verify the predictive ability of the model, the eSAFT-HR EoS was extrapolated to the Zoghi and Feyzi (2013) solubility results of the same quaternary system that were obtained at higher pressures or higher CO₂ loadings at the same temperatures. The AAD of the present model is 11.39% lower.     

Phase equilibrium for ozone-containing hydrates formed from an (ozone + oxygen) gas mixture coexisting with gaseous carbon dioxide and liquid water

The paper reports the three-phase (gas + aqueous liquid + hydrate) equilibrium pressure (p) versus temperature (T) data for a (O₃ + O₂ + CO₂ + H₂O) system and, for comparison, corresponding data for a (O₂ + CO₂ + H₂O) system for the first time. These data cover the temperature range from (272 to 279) K, corresponding to pressures up to 4 MPa, for each of the three different (O₃ + O₂)-to-CO₂ or O₂-to-CO₂ mole ratios in the gas phase, which are approximately 1:9, 2:8, and 3:7, respectively. The mole fraction of ozone in the gas phase of the (O₃ + O₂ + CO₂ + H₂O) system was from ∼0.004 to ∼0.02. The modified pressure-search method, developed in our previous study [S. Muromachi, T. Nakajima, R. Ohmura, Y.H. Mori, Fluid Phase Equilib. 305 (2011) 145–151] for p–T measurements in the presence of chemically unstable ozone, was applied, having been further modified for dealing with highly water-soluble CO₂, for the (O₃ + O₂ + CO₂ + H₂O) system, while the conventional temperature-search method was used for the (O₂ + CO₂ + H₂O) system. The measurement uncertainties (with 95% coverage) were ±0.11 K for T, ±6.0 kPa for p, and ±0.0015 for the mole fraction of each species in the gas phase. It was confirmed that, at a given CO₂ fraction in the gas phase, p for the (O₃ + O₂ + CO₂ + H₂O) system was consistently lower than that for the (O₂ + CO₂ + H₂O) system over the entire T range of the present measurements, indicating a preference of O₃ to O₂ in the uptake of guest-gas molecules into the cages of a structure I hydrate.     

Choline biosensors based on a bi-electrocatalytic property of MnO2 nanoparticles modified electrodes to H2O2

An interesting mode of reactivity of MnO₂ nanoparticles modified electrode in the presence of H₂O₂ is reported. The MnO₂ nanoparticles modified electrodes show a bi-direction electrocatalytic ability toward the reduction/oxidation of H₂O₂. Based on this property, a choline biosensor was fabricated via a direct and facile electrochemical deposition of a biocomposite that was made of chitosan hydrogel, choline oxidase (ChOx) and MnO₂ nanoparticles onto a glassy carbon (GC) electrode. The biocomposite is homogeneous and easily prepared and provides a shelter for the enzyme to retain its bioactivity. The results of square wave voltammetry showed that the electrocatalytic reduction currents increased linearly with the increase of choline chloride concentration in the range of 1.0 × 10⁻⁵ –2.1 × 10⁻³ M and no obvious interference from ascorbic acid and uric acid was observed. Good reproducibility and stability were obtained. A possible reaction mechanism was proposed.     

Thermophysical properties and phase equilibria study of the binary systems {N-hexylquinolinium bis(trifluoromethylsulfonyl)imide + aromatic hydrocarbons,or an alcohol}

The new quinolinium ionic liquid has been synthesised as a continuation of our work with quinolinium-based ionic liquids (ILs). The work includes specific basic characterisation of synthesized compounds: N-hexylquinolinium bromide, [HQuin][Br] and N-hexylquinolinium bis{(trifluoromethyl)sulfonyl}imide [HQuin][NTf₂] by NMR spectra, elementary analysis and water content. The basic thermal properties of the pure [HQuin][NTf₂] i.e. melting and glass-transition temperatures, the enthalpy of fusion as well as heat capacity have been measured using a differential scanning microcalorimetry technique (DSC) and thermal analysis instrument (TA). Densities and viscosities were determined as a function of temperature. Phase equilibria for the binary systems: {[HQuin][NTf₂]) + aromatic hydrocarbon (benzene, or toluene, or ethylbenzene, or n-propylbenzene), or an alcohol (1-butanol, or 1-hexanol, or 1-octanol, or 1-decanol)} have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (270 to 320) K. For all the binary systems with benzene and alkylbenzenes, the eutectic diagrams were observed with immiscibility gap in the liquid phase beginning from (0.13 to 0.28) mole fraction of the IL with very high an upper critical solution temperature (UCST). For mixtures with alcohols, the complete miscibility was observed for 1-butanol and immiscibility with UCST in the liquid phase for the remaining alcohols. The typical dependence was observed, that with increasing chain length of an alcohol the solubility decreases. The well-known NRTL equation was used to correlate experimental (solid + liquid), SLE and (liquid + liquid), LLE phase equilibria data sets. For the systems containing immiscibility gaps, (IL + an alcohol) parameters of the LLE correlation were used to the prediction of SLE.     

Measurement and modeling of high-pressure (vapour + liquid) equilibria of (CO2 + alcohol) binary systems

An apparatus based on a static-analytic method assembled in this work was utilized to perform high pressure (vapour + liquid) equilibria measurements with uncertainties estimated at <5%. Complementary isothermal (vapour + liquid) equilibria results are reported for the (CO₂ + 1-propanol), (CO₂ + 2-methyl-1-propanol), (CO₂ + 3-methyl-1-butanol), and (CO₂ + 1-pentanol) binary systems at temperatures of (313, 323, and 333) K, and at pressure range of (2 to 12) MPa. For all the (CO₂ + alcohol) systems, it was visually monitored to insure that there was no liquid immiscibility at the temperatures and pressures studied. The experimental results were correlated with the Peng–Robinson equation of state using the quadratic mixing rules of van der Waals with two adjustable parameters. The calculated (vapour + liquid) equilibria compositions were found to be in good agreement with the experimental values with deviations for the mol fractions <0.12 and <0.05 for the liquid and vapour phase, respectively.     

Enthalpy of absorption and limit of solubility of CO2 in aqueous solutions of 2-amino-2-hydroxymethyl-1,3-propanediol, 2-[2-(dimethyl-amino)ethoxy] ethanol,and 3-dimethyl-amino-1-propanol at T = (313.15 and 353.15) K and pressures up to 2 MPa

In order to study the influence of amine structure on absorption of carbon dioxide, enthalpies of solution of CO₂ in 2.50 mol · L^?1 aqueous solutions of 2-amino-2-hydroxymethyl-1,3-propanediol (THAM), 2-[2-(dimethyl-amino)ethoxy] ethanol (DMAEOE), and 3-dimethyl-amino-1-propanol (DMAP) were measured. The enthalpies of solution are determined as function of gas loading charge (moles of CO₂/mole of amine), at temperatures (313.15 and 353.15) K, and pressures range from (0.5 to 2) MPa. Measurements were carried out using a flow calorimetric technique. CO₂ solubilities in the aqueous solutions of amine are derived from calorimetric data. Molar volumes of aqueous amine solutions required to handle calorimetric data were determined at 303.15 K using a vibrating tube densimeter. Experimental enthalpies of solution are discussed on the basis of amines alkalinity.     

Potentiometric study of acid–base equilibria in the {KCl + LiCl} eutectic melt at temperatures in the range (873 to 1073) K

Some heterogeneous reactions of oxide ion exchange (carbonate ion dissociation and magnesium oxide dissolution) in the molten {KCl + LiCl} eutectic at temperatures of (873, 973 and 1073) K were studied using an electrochemical cell with an oxygen membrane electrode Pt(O₂)|ZrO₂(Y₂O₃). The dissociation constant of the CO₃²⁻ was found to increase with increasing temperature: pK (873 K)=(2.39 ± 0.05); pK (973 K)=(1.81 ± 0.09); pK (1073 K)=(1.53 ± 0.08). Removal of CO₂ from the gas above the melt allows the complete transformation of CO₃²⁻ to O²⁻. pP_MgO values decrease more from (6.99 ± 0.08) to (5.41 ± 0.04). The oxobasicity indices, pI_(KCl+LiCl), were calculated from the solubility data to be 3.2 at 873 K, 3.4 at 973 K, and 3.6 at 1073 K. This trend suggests an increase in acidity with increasing temperature of {KCl + LiCl}.     

Carbon dioxide solubility in aqueous potassium salt solutions of l-proline and dl-α-aminobutyric acid at high pressures

In the present work, the solubility of CO₂ in aqueous solutions of potassium prolinate (KPr) and potassium α-aminobutyrate (KAABA) was measured at temperatures (313.2, 333.2, and 353.2) K and CO₂ partial pressures up to 1000 kPa for amino acid salt concentrations: KPr, w = (7.5, 14.5, and 27.4 wt%) and KAABA, w = (6.9, 13.4, and 25.6 wt%). It was found that the CO₂ absorption capacities of the studied amino acid salt systems were considerably high and comparable with that of industrially important alkanolamines including monoethanolamine. The CO₂ loadings in aqueous potassium α-aminobutyrate at high pressures were also found to be generally higher than the loadings in aqueous potassium prolinate. A modified Kent–Eisenberg model was applied to correlate the CO₂ solubility in the amino acid salt solution as function of CO₂ partial pressure, temperature, and concentration. The model gave good representation of the (vapour + liquid) equilibrium data obtained for the amino acid salt systems studied, and provided accurate predictions of the solubility.     

Experimental observations on the competing effect of tetrahydrofuran and an electrolyte and the strength of hydrate inhibition among metal halides in mixed CO2 hydrate equilibria

In the present work, experimental data on the equilibrium conditions of mixed CO₂ and THF hydrates in aqueous electrolyte solutions are reported. Seven different electrolytes (metal halides) were used in this work namely sodium chloride (NaCl), calcium chloride (CaCl₂), magnesium chloride (MgCl₂), potassium bromide (KBr), sodium fluoride (NaF), potassium chloride (KCl), and sodium bromide (NaBr). All equilibrium data were measured by using Cailletet apparatus. Throughout this work, the overall concentration of CO₂ and THF were kept constant at (0.04 and 0.05) mol fraction, respectively, while the concentration of electrolytes were varied. The experimental temperature ranged from (275 to 305) K and pressure up 7.10 MPa had been applied. From the experimental results, it is concluded that THF, which is soluble in water is able to suppress the salt inhibiting effect in the range studied. In all quaternary systems studied, a four-phase hydrate equilibrium line was observed where hydrate (H), liquid water (L_W), liquid organic (L_V), and vapour (V) exist simultaneously at specific pressure and temperature. The formation of this four-phase equilibrium line is mainly due to a liquid–liquid phase split of (water + THF) mixture when pressurized with CO₂ and the split is enhanced by the salting-out effect of the electrolytes in the quaternary system. The strength of hydrate inhibition effect among the electrolytes was compared. The results shows the hydrate inhibiting effect of the metal halides is increasing in the order NaF < KBr < NaCl < NaBr < CaCl₂ < MgCl₂. Among the cations studied, the strength of hydrate inhibition increases in the following order: K⁺ < Na⁺ < Ca²⁺ < Mg²⁺. Meanwhile, the strength of hydrate inhibition among the halogen anion studied decreases in the following order: Br^? > Cl^? > F^?. Based on the results, it is suggested that the probability of formation and the strength of ionic–hydrogen bond between an ion and water molecule and the effects of this bond on the ambient water network are the major factors that contribute to hydrate inhibition by electrolytes.