Diatom-templated TiO2 with enhanced photocatalytic activity: biomimetics of photonic crystals

The siliceous frustules with sophisticated optical structure endow diatoms with superior solar light-harvesting abilities for effective photosynthesis. The preserved frustules of diatom (Cocconeis placentula) cells, as biophotonic crystals, were thus employed as both hard templates and silicon resources to synthesize TiO₂ photocatalyst. Characterizations by a combination of physicochemical techniques proved that the bio-inspired sample is TiO₂-coated SiO₂ with biogenic C self-doped in. It was found that the synthesized composites exhibited similar morphologies to the original diatom templates. In comparison with commercial Degussa P25 TiO₂, the C-doped TiO₂/SiO₂ catalyst exhibited more light absorption in the visible region and higher photocatalytic efficiency for photodegradation of rhodamine B under visible light due to the biomorphic hierarchical structures, TiO₂ coating and C-doping.     

Remarkably enhanced photocatalytic activity by sulfur-doped titanium dioxide in nanohybrids with carbon nanotubes

TiO₂ doped S nanohybrids with carbon nanotubes (CNTs) were synthesized with CNTs, thiourea and TiO₂ nanoparticles. The result indicated that the TiO₂ nanoparticles with about 8 nm in size are attached on the sidewall of CNTs. The nanohybrids material can absorb at longer wavelength and the absorption even covers the whole range of visible region than that only TiO₂ nanoparticles. Application of the catalysts to photocatalytic degradation of methylene blue (MB) was tested under visible light irradiation. The result suggests that a high MB degradation activity of S-TiO₂/CNTs due to a reduce band gap of TiO₂ when S is doped, and the decrease in the possibility of electron–hole recombination by CNTs. In addition, the density functional-theory (DFT) calculations of the electronic band structures and density of states (DOS) to understand the bonding states between TiO₂ and CNTs, proved that the TiO₂/CNTs system is stable.     

Preparation and characterization of polyphosphotungstate/ZrO2 nanocomposite and their sonocatalytic and photocatalytic activity under UV light illumination

Polyoxometalates (POM) supported on zirconia, H₃PW₁₂O₄₀/ZrO_2, were prepared by incorporating polyphosphotungstate into a zirconia matrix via sol-gel technique that involving the hydrolysis of zirconium (IV) n-butoxide, Zr (n-OBu)₄, as the ZrO₂ source. This insoluble and readily separable catalyst was characterized by using XRD, FT-IR, SEM, and UV diffuse reflectance spectroscopy (UV-DRS), indicating that the polyphosphotungstate was chemically attached to the zirconia supports, and primary Keggin structure remained intact. The photocatalytic and sonocatalytic activity of the supported polyphosphotungstate was tested via degradation of different dyes in aqueous solutions. The POM-ZrO₂ nanocomposite showed higher photocatalytic and sonocatalytic activity than pure polyoxometalate or pure ZrO₂.     

Ultrathin MnO2 nanosheets grown on hollow carbon spheres with enhanced capacitive performance

Ultrathin MnO₂ nanosheets grown on the surface of hollow carbon spheres (MnO₂/HCSs) were fabricated by the redox reaction between carbon spheres with KMnO₄ in aqueous solution. Due to the porous structure and large amounts of active sites, MnO₂/HCSs exhibit excellent capacitive performance with 227.5 F g⁻¹ at 1 A g⁻¹. After 5000 cycles, the capacity retention of MnO₂/HCSs remains 96%, indicating its good cycling stability. These results demonstrate that MnO₂/HCSs are promising supercapacitor electrode material and this work provide a facile method for growth of ultrathin MnO₂ nanosheets on carbon substrate.     

Hydrodynamic cavitation-enhanced photocatalytic activity of P-doped TiO2 for degradation of ciprofloxacin: Synergetic effect and mechanism

Hybrid methods with an enhanced oxidation capacity have been proposed for the removal of organic contaminants based on combining hydrodynamic cavitation (HC) with advanced oxidation processes (AOPs). In this study, we utilize the synergetic effect between photocatalytic processes and HC to strengthen ciprofloxacin (CIP) degradation by P-doped TiO₂ catalysts. In comparison to a degradation ratio of 20.37 % in HC and 55.7 % in P-TiO₂-based photocatalytic processes alone, the CIP degradation ratio reached as high as 90.63 % in HC-assisted photocatalytic processes with the optimal experimental parameters. The mechanic microjets treatment originated from HC make P-TiO₂ nano photocatalysts with significantly increased surface area, smaller particle sizes, cleaner surface and improved dispersion, which were found using SEM, TEM, and BET analysis. Possible degradation mechanisms and reaction pathways of CIP during hybrid HC + photocatalytic processes were explored by coupling free radical capture experiments and liquid chromatography-mass spectrometry . This hybrid HC + photocatalytic technique has a potential application in the treatment of antibiotic sewage at the industrial level.     

Synthesis and characterization of nitrogen-doped TiO2 coatings on reduced graphene oxide for enhancing the visible light photocatalytic activity

Nitrogen-doped TiO₂ coatings on reduced graphene oxide were prepared via a sonochemical synthesis and hydrothermal process. The nanocomposites showed improved photocatalytic activity due to their large specific surface areas (185–447 m²/g), the presence of TiO₂ in the anatase phase, and a quenched photoluminescence peak. In particular, GN3-TiO₂ (nitrogen-doped TiO₂ coatings on rGO with 3 ml of titanium (IV) isopropoxide) exhibited the best photocatalytic efficiency and degradation rate among the materials prepared. With nitrogen-doped on the reduced graphene oxide surface, the photocatalytic activity is enhanced approximately 17.8 times compared to that of the pristine TiO₂. The dramatic enhancement of activity is attributed to the nitrogen contents and rGO effectively promoting charge-separation efficiency and providing abundant catalytically active sites to enhance the reactivity. The composites also showed improved pollutant adsorption capacity, electron–hole pair lifetime, light absorption capability, and absorbance of visible light.     

Layer-by-layer assembly of Ag2S quantum dots-sensitized ZnO/SnO2 core-shell nanowire arrays for enhanced photocatalytic activity

Ag₂S quantum dots-sensitized ZnO/SnO₂ core-shell nanowire arrays were successfully synthesized layer by layer through hydrothermal growth, atomic layer deposition, and successive ionic layer adsorption and reaction process. By introducing the two-layer semiconductors, the bandgap of ZnO component in the arrays was slightly modulated, while the light absorption was obviously improved with an absorptivity higher than 95% in visible and ultraviolet range. In contrast to the ZnO NW arrays, the photocurrent response of the ZnO/SnO₂/Ag₂S NW arrays for the visible light was improved from 0.42 μA to 22.5 μA, and the photodegradation efficiency of methylene blue was increased from 45.24% to 71.61%, and 42.61% to 57.58%, respectively in visible light and ultraviolet light. Band structure analysis indicated that the coating layer brought different staggered gaps and suitable band alignment for efficient photocatalytic performance, which could be extended to design heterogeneous semiconductor nanomaterials for their potential applications.     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 hollow spheres

Nd-doped titania hollow spheres were prepared using carbon spheres as template and Nd-doped titania nanoparticles as building blocks. The Nd-doped titania nanoparticles were synthesized at low temperature. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectrum (DRS). The effects of Nd content on the physical structure and photocatalytic activities of doped titania hollow sphere samples were investigated. Results showed that there was an optimal Nd-doped content (3.9 at.%) for the photocatalytic degradation of dye X-3B (C.I. Reactive Red 2). The apparent rate constant of the best one was almost 9 times as that of P25 titania. The mechanism of photocatalytic degradation of dyes under visible light irradiation was also discussed.     

Synergetic effects of hydrophilic surface modification and N-doping for visible light response on photocatalytic activity of TiO2

We made attempts to improve photocatalytic activity of TiO₂ nanoparticles under visible light exposure by combining additional treatments. N-doping of TiO₂ by ammonia gas treatment increased absorbance of visible light. By coating thin film of polydimethylsiloxane, and subsequently vacuum-annealing, TiO₂ surface became more hydrophilic, thereby enhancing photocatalytic activity of TiO₂. These two treatments were combined for the first time in this work and photocatalytic activity under visible light irradiation exceeded sum of individual effects of N-doping and hydrophilic modification.     

Effect of hydrothermal temperature on photocatalytic properties of TiO2 nanotubes

This work presents a study on the effect of hydrothermal temperature and structure on the photocatalytic activity of TiO₂ nanotubes (TNT) prepared using commercially available TiO₂ nanoparticles (P25). From the results, it was found that a higher hydrothermal temperature led to an increase in the specific surface area, total pore volume, and the size of mesopores in TNT. Moreover, the TNTs synthesized by the hydrothermal method had a new structure, which was very different from the anatase and rutile structures found in P25. The TNTs synthesized at 150 °C had the highest specific surface area of 371 m²/g. However, the TNTs synthesized at 180 °C exhibited the best photocatalytic efficiency and dye adsorption capacity, as compared to other TNTs, resulting from their well-developed mesopores.     

A one-pot method to prepare N-doped titania hollow spheres with high photocatalytic activity under visible light

N-doped titania hollow spheres (NTHS) were prepared by a one-pot hydrothermal method using urea as precursor of nitrogen. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectrum (DRS). The photocatalytic activity of as-prepared titania hollow spheres was determined by degradation of Reactive Brilliant Red dye X-3B (C.I. reactive red 2) under visible light irradiation, and was compared to non-doped titania hollow spheres and commercial P25 titania. Results indicated that the as-prepared NTHS showed highest photocatalytic activity.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Influence of ammonia on the morphologies and enhanced photocatalytic activity of TiO2 micro/nanospheres

TiO₂ micro/nanospheres were synthesized by a combination process contains hydrolysis of titanium tetra-n-butyl in mixed solution of anhydrous ethanol/ammonia and the subsequent calcination under 550 °C for 7 h. The pH values of the mixed solution were tuned to be 10.4, 11.0 and 11.6, respectively, by adding different amounts of ammonia. Scanning electron microscope (SEM) and transmission electron microscope (TEM) were used to characterize the morphologies and the crystallinity. X-ray diffraction (XRD) patterns indicated that pH value of the precursors has an important effect on the crystal phase composition. UV-vis diffuse reflectance spectrum was applied to characterize the optical properties of samples. Degradation of methylene blue under the irradiation of 300 W Hg lamp confirmed the enhanced photocatalytic activity of TiO₂ micro/nanospheres. In addition, the formation mechanism was proposed.     

g-C3N4 modified Bi2O3 composites with enhanced visible-light photocatalytic activity

Novel g-C₃N₄ modified Bi₂O₃ (g-C₃N₄/Bi₂O₃) composites were synthesized by a mixing-calcination method. The samples were characterized by thermogravimetry (TG), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), UV–vis diffuse reflection spectroscopy (DRS), photoluminescence (PL) and photocurrent-time measurement (PT). The photocatalytic activity of the composites was evaluated by degradation of Rhodamine B (RHB) and 4-chlorophenol (4-CP) under visible light irradiation (>400 nm). The results indicated that the g-C₃N₄/Bi₂O₃ composites showed higher photocatalytic activity than that of Bi₂O₃ and g-C₃N₄. The enhanced photocatalytic activity of the g-C₃N₄/Bi₂O₃ composites could be attributed to the suitable band positions between g-C₃N₄ and Bi₂O₃. This leads to a low recombination between the photogenerated electron–hole pairs. The proposed mechanism for the enhanced visible-light photocatalytic activity of g-C₃N₄/Bi₂O₃ composites was proven by PL and PT analysis.     

Enhanced photocatalytic performance of ultrasound treated GO/TiO2 composite for photocatalytic degradation of salicylic acid under sunlight illumination

The current research work deals with the preparation of TiO₂ and GO/TiO₂ composite by simple, chemical, cost effective hydrothermal method. Graphene oxide (GO) is prepared by modified Hummer’s method. Dispersion of GO is achieved by an ultrasonic cleaning bath for 1 h. using a power of 200 W and at a frequency of 40 kHz. The prepared catalyst material is characterized by different characterization techniques. XRD study confirms the prepared material is polycrystalline in nature. The synthesized TiO₂ and GO/TiO₂ photocatalyst materials are used to study the photocatalytic degradation of salicylic acid under sunlight illumination. GO/TiO₂ composite shows superior photocatalytic activity than TiO₂. GO/TiO₂ composite shows 57% degradation of salicylic acid. Mineralization of salicylic acid is studied using chemical oxygen demand.     

Study on the photocatalytic activity of TiN/TiO2 nanoparticle formed by ball milling

TiN/TiO₂ nanoparticle photocatalyst was prepared by ball milling of TiO₂ in H₂O solution doped with TiN. The photocatalyst was characterized by UV–Vis diffuse reflection spectroscopy, X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Based on the results of the characterization, the mechanism of the increase in photocatalytic activity was investigated. The results show that when the amount of doped TiN is 0.15 wt%, the photocatalytic activity of the TiN/TiO₂ is at its peak. Compared with TiO₂, the photoabsorption wavelength range of the TiN/TiO₂ photocatalyst red-shifts about 30 nm, and the photoabsorption intensity increases as well. The photocatalytic activities of the photocatalyst are higher than that of TiO₂ under UV and visible light irradiation. The increase of surface Ti³⁺ reactive center and the extension of the photoabsorption wavelength are the main factors for the increase in the photocatalytic activity of the TiN/TiO₂. Doped TiN neither changes the TiO₂ crystal phase nor creates new crystal phase by ball milling.     

The super-hydrophobic IR-reflectivity TiO2 coated hollow glass microspheres synthesized by soft-chemistry method

The super-hydrophobic and IR-reflectivity hollow glass microspheres (HGM) was synthesized by being coated with anatase TiO₂ and a super-hydrophobic material. The super-hydrophobic self-cleaning property prolong the life time of the IR reflectivity. TBT and PFOTES were firstly applied and hydrolyzed on HGM and then underwent hydrothermal reaction to synthesis anatase TiO₂ film. For comparison, the PFOTES/TiO₂ mutual-coated HGM (MCHGM), PFOTES single-coated HGM (F-SCHGM) and TiO₂ single-coated HGM (Ti-SCHGM) were synthesized as well. The MCHGM had bigger contact angle (153°) but smaller sliding angle (16°) than F-SCHGM (contact angle: 141.2°; sliding angle: 67°). Ti-SCHGM and MCHGM both showed similar IR reflectivity with ca. 5.8% increase compared with original HGM and F-SCHGM. For the thermal conductivity, coefficients of F-SCHGM (0.0479 W/(m K)) was basically equal to that of the original HGM (0.0475 W/(m K)). Negligible difference was found between the thermal conductivity coefficients of MCHGM-coated HGM (0.0543 W/(m K)) and Ti-SCHGM (0.0546 W/(m K)).     

Synthesis of Br-doped TiO<Subscript>2</Subscript> hollow spheres with enhanced photocatalytic activity

The Br-doped hollow TiO₂ photocatalysts were prepared by a simple hydrothermal process on the carbon sphere template following with calcination at 400 °C. The structure and properties of photocatalysts were characterized by X-ray diffraction, Raman spectrum, scanning electron microscope, transmission electron microscopy, N₂ desorption–adsorption, UV–Vis spectroscopy, and X-ray photoelectron spectroscopy. The TiO₂ hollow spheres are in diameter of 500 nm with shell thickness of 50 nm. The shell is composed of small anatase nanoparticles with size of about 10 nm. The TiO₂ hollow spheres exhibit high crystalline and high surface area of 89.208 m²/g. With increasing content of Br doping, the band gap of TiO₂ hollow spheres decreased from 2.85 to 1.75 eV. The formation of impurity band in the band gap would narrow the band gap and result in the red shift of absorption edge from 395 to 517 nm, which further enhances the photocatalytic activity. The appropriate Br doping improves the photocatlytic activity significantly. The TiO₂ hollow spheres with 1.55% Br doping (0.5Br-TiO₂) exhibit the highest photocatalytic activity under full light. More than 98% of RhB, MO, and MB can be photodegraded using 0.5Br-TiO₂ with concentration of 10 mg/L in 40, 30, and 30 min, respectively. The degradation rate of Br-doped photocatalysts was 40% faster than undoped ones.

Open image in new window

Graphical abstract

     

Preparation and surface encapsulation of hollow TiO nanoparticles for electrophoretic displays

Hollow black TiO nanosparticles were obtained via deposition of inorganic coating on the surface of hollow core-shell polymer latex with Ti(OBu)₄ as precursor and subsequent calcination in ammonia gas. Hollow TiO particles were characterized by scanning electron microscope, transmission electronic microscopy, X-ray diffraction, and thermogravimetric analysis. Encapsulation of TiO via dispersion polymerization was promoved by pretreating the pigments with 3-(trimethoxysilyl) propyl methacrylate, making it possible to prepare hollow TiO-polymer particles. When St and DVB were used as polymerization monomer, hollow TiO-polymer core-shell particles came into being via dispersion polymerization, and the lipophilic degree is 28.57%. Glutin-arabic gum microcapsules containing TiO-polymer particles electrophoretic liquid were prepared using via complex coacervation. It was founded that hollow TiO-polymer particles had enough electrophoretic mobility after coating with polymer.     

Hierarchical hollow urchin-like structured MnO2 microsphere/carbon nanofiber composites as anode materials for Li-ion batteries

In this work, novel hollow urchin-like MnO₂ microspheres (u-MnO₂), consisting of a hollow core with nanotubes, are synthesized by a simple hydrothermal process. The morphology of the MnO₂ structures could be tuned from round particles to a hierarchical hollow urchin structure by controlling the hydrothermal reaction time, with no need for surfactant or templates. The nanostructures of the obtained u-MnO₂ are characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) pattern of the u-MnO₂ reveals a tetragonal structure of α-MnO₂. The carbon nanofibers (CNFs) are uniformly deposited on u-MnO₂ to improve the electrical conductivity and to utilize the hierarchical architecture of u-MnO₂. As the anode electrode of Li-ion batteries, the u-MnO₂/CNFs nanocomposites exhibit discharge capacity of 988 mAh·g⁻¹ after 100 cycles with a good rate capability. The superior electrochemical performances of the u-MnO₂/CNFs nanocomposites can be attributed to the hierarchical urchin-like structures and the superior electrical conductivity of the nanocomposites, which can facilitate fast electron and ion transport and accommodate a large volume change during charge/discharge.