A novel planar D‐A alternating copolymer with D‐A integrated structures exhibiting H‐aggregate behaviors for polymer solar cells

With the D‐A integrated structure concept, a new donor–acceptor (D‐A) copolymer poly{(N‐dodecyl‐carbazole[3,4‐c:5,6‐c]bis[1,2,5]thiadiazole‐alt‐4,8‐di(2‐ethylhexy‐loxyl)benzo[1,2‐b:4,5‐b′]dithiophene)} has been designed and synthesized using a novel architecture N‐dodecyl‐carbazole[3,4‐c:5,6‐c]bis[1,2,5]thiadiazole, and di(2‐ethylhexy‐loxyl)benzo[1,2‐b:4,5‐b′]dithiophene) as the basic building blocks. The copolymer has a low‐lying highest occupied molecular orbital energy level of ?5.41 eV and a broaden absorption matching well with the main solar photon flux. Note that an H‐aggregation beneficial for charge transportation and collection is formed in the macromolecules film, which implies that the planar D‐A integrated structure favors the strong intermolecular interaction to render molecules aggregated via face‐to‐face self‐assembly. The aggregation becomes larger scale after thermal annealing. Additionally, obvious intramolecular charge transfer and energy transfer have occurred in created D‐A integration. Without any treatment, the resulting polymer achieved a efficiency of 2.0% and relatively high open‐circuit voltage (V_oc) value of 0.77 V when blended with [6,6]‐phenyl‐C61‐butyric acid methyl ester in a typical bulk heterojunction. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

The role of alkane dithiols in controlling polymer crystallization in small band gap polymer:Fullerene solar cells

The effect of the addition of 1,8‐octanedithiol (ODT) during processing on the microstructure of blend films of poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7(2,1,3‐benzothiadiazole)] (PCPDTBT) and [6,6]‐phenyl‐C₇₁ butyric acid methyl ester ([70]PCBM) is studied. Grazing incidence X‐ray diffraction and absorption spectroscopy show that the crystalline order of PCPDTBT increases when ODT is introduced in the solution phase either to neat polymer systems or to blends with [70]PCBM. The increased crystalline order is accompanied by less dispersive hole transport in the polymer, and leads to a more efficient formation of a percolating fullerene network within the blend. This contributes to an increase in photocurrent generation. However, the bimolecular recombination rate as determined from photovoltage transients increases upon addition of ODT, limiting the power conversion efficiency to values well below those expected from the energy levels of PCPDTBT. We propose some explanations for this increase in bimolecular recombination, based also on variable angle spectroscopic ellipsometry measurements. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Diketopyrrolopyrrole‐based liquid crystalline conjugated donor–acceptor copolymers with reduced band gap for polymer solar cells

A new liquid crystalline (LC) acceptor monomer 2,5‐bis[4‐(4′‐cyanobiphenyloxy)dodecyl]‐3,6‐dithiophen‐2‐yl‐pyrrolo[3,4‐c]pyrrole‐1,4‐dione (TDPPcbp) was synthesized by incorporating cyanobiphenyl mesogens into diketopyrrolopyrrole (DPP). The monomer was copolymerized with bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′] dithiophene (BDT) and N‐9′‐heptadecanylcarbazole (CB) donors to obtain donor–acceptor alternating copolymers poly[4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐alt‐3,6‐bis(thiophen‐5‐yl)‐2,5‐bis[4‐(4′‐cyanobiphenyloxy)dodecyl]‐2,5‐dihydropyrrolo[3,4‐c]pyrrole‐1,4‐dione] (PBDTDPPcbp) and poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐3,6‐bis(thiophen‐5‐yl)‐2,5‐bis[4‐(4′‐cyano‐biphenyloxy)dodecyl]‐2,5‐dihydropyrrolo[3, 4‐c]pyrrole‐1,4‐dione] (PCBTDPPcpb) with reduced band gap, respectively. The LC properties of the copolymers, the effects of main chain variation on molecular packing, optical properties, and energy levels were analyzed. Incorporating the mesogen cyanobiphenyl units not only help polymer donors to pack well through mesogen self‐organization but also push the fullerene acceptor to form optimized phase separation. The bulk heterojunction photovoltaicdevicesshow enhanced performance of 1.3% for PBDTDPPcbp and 1.2% for PCBTDPPcbp after thermal annealing. The results indicate that mesogen‐controlled self‐organization is an efficient approach to develop well‐defined morphology and to improve the device performance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Novel low‐bandgap oligothiophene‐based donor‐acceptor alternating conjugated copolymers: Synthesis,properties, and photovoltaic applications

A series of novel soluble donor‐acceptor low‐bandgap‐conjugated polymers consisting of different oligothiophene (OTh) coupled to electron‐accepting moiety 2‐pyran‐4‐ylidenemalononitrile (PM)‐based unit were synthesized by Stille or Suzuki coupling polymerization. The combination of electron‐accepting PM building block with varied OTh_n (the number of thiophene unit increases from 3 to 5) results in enhanced π–π stacking in solid state and intramolecular charge transfer (ICT) transition, which lead to an extension of the absorption spectra of the copolymers. Cyclic voltammetry measurements and molecular orbital distribution calculations indicate that the highest occupied molecular orbitals (HOMO) energy levels could be fine‐tuned by changing the number of thiophene units of the copolymers, and the resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high‐open circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction photovoltaic devices were fabricated by using the copolymers as donors and (6,6)‐phenyl C₆₁‐butyric acid methyl ester as acceptor. It was found that the highest V_oc reached 0.94 V, and the short circuit currents (J_sc) were improved from 1.78 to 2.54 mA/cm², though the power conversion efficiencies of the devices were measured between 0.61 and 0.99% under simulated AM 1.5 solar irradiation of 100 mW/cm², which indicated that this series copolymers can be promising candidates for the photovoltaic applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2765–2776, 2010     

Synthesis and photovoltaic properties of a low‐band‐gap polymer consisting of alternating thiophene and benzothiadiazole derivatives for bulk‐heterojunction and dye‐sensitized solar cells

We synthesized a novel low‐band‐gap, conjugated polymer, poly[4,7‐bis(3′,3′‐diheptyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole] [poly(heptyl₄‐PTBT)], consisting of alternating electron‐rich, diheptyl‐substituted propylene dioxythiophene and electron‐deficient 2,1,3‐benzothiadiazole units, and its photovoltaic properties were investigated. A thin film of poly(heptyl₄‐PTBT) exhibited an optical band gap of 1.55 eV. A bulk‐heterojunction solar cell with indium tin oxide/poly(3,4‐ethylenedioxythiophene)/poly(heptyl₄‐PTBT): methanofullerene [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) (1:4)/LiF/Al was fabricated with poly(heptyl₄‐PTBT) as an electron donor and PCBM as an electron acceptor and showed an open‐circuit voltage, short‐circuit current density, and power conversion efficiency of 0.37 V, 3.15 mA/cm², and 0.35% under air mass 1.5 (AM1.5G) illumination (100 mW/cm²), respectively. A solid‐state, dye‐sensitized solar cell with a SnO₂:F/TiO₂/N3 dye/poly(heptyl₄‐PTBT)/Pt device was fabricated with poly(heptyl₄‐PTBT) as a hole‐transport material. This device exhibited a high power conversion efficiency of 3.1%, which is the highest power conversion efficiency value with hole‐transport materials in dye‐sensitized solar cells to date. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1394–1402, 2007     

Silole‐containing polymers for high‐efficiency polymer solar cells

Silole‐containing conjugated polymers ( P1 and P2 ) carrying methyl and octyl substituents, respectively, on the silicon atom were synthesized by Suzuki polycondensation. They show strong absorption in the region of 300–700 nm with a band gap of about 1.9 eV. The two silole‐containing conjugated polymers were used to fabricate polymer solar cells by blending with PC₆₁BM and PC₇₁BM as the active layer. The best performance of photovoltaic devices based on P1 /PC₇₁BM active layer exhibited power conversion efficiency (PCE) of 2.72%, whereas that of the photovoltaic cells fabricated with P2 /PC₇₁BM exhibited PCE of 5.08%. 1,8‐Diiodooctane was used as an additive to adjust the morphology of the active layer during the device optimization. PCE of devices based on P2 /PC₇₁BM was further improved to 6.05% when a TiO_x layer was used as a hole‐blocking layer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Conjugated polymer‐functionalized graphite oxide sheets thin films for enhanced photovoltaic properties of polymer solar cells

In this study, the maleimide‐thiophene copolymer‐functionalized graphite oxide sheets (PTM21‐GOS) and carbon nanotubes (PTM21‐CNT) were developed for polymer solar cell (PSC) applications. The grafting of PTM21‐OH onto the CNT and GO sheets was confirmed using FTIR spectroscopy. PTM21‐CNT and PTM21‐GOS exhibited excellent dispersal behavior in organic solvents. Better thermal stability was observed for PTM21‐CNT and PTM21‐GOS as compared with that for PTM21‐OH. In addition, the optical band gaps of PTM21‐GOS and PTM21‐CNT were lower than that of PTM21‐OH. We incorporated PTM21‐GOS and PTM21‐CNT individually into poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) blends for use as photoconversion layers of PSCs. Good distributional homogeneity was observed for PTM21‐GOS or PTM21‐CNT in the P3HT/PCBM blend film. The UV–vis absorption peaks of the blend films red‐shifted slightly upon increasing the content of PTM21‐GOS or PTM21‐CNT. The band gap energies and LUMO/HOMO energy levels of the P3HT/PTM21‐GOS and P3HT/PTM21‐CNT blend films were slightly lower than those of the P3HT film. The conjugated polymer‐functionalized PTM21‐GOS and PTM21‐CNT behaved as efficient electron acceptors and as charge‐transport assisters when incorporated into the photoactive layers of the PSCs. PV performance of the PSCs was enhanced after incorporating PTM21‐GOS or PTM21‐CNT in the P3HT/PCBM blend. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Soluble narrow‐band‐gap copolymers containing novel cyclopentadithiophene units for organic photovoltaic cell applications

Five novel conjugated copolymers ( P1 – P5 ) containing coplanar cyclopentadithiophene (CPDT) units (incorporated with arylcyanovinyl and keto groups in different molar ratios) were synthesized and developed for the applications of polymer solar cells (PSCs). Polymers P1 – P5 covered broad absorption ranges from UV to near infrared (400–900 nm) with narrow optical band gaps of 1.38–1.70 eV, which are compatible with the maximum solar photon reflux. Partially reversible p‐ and n‐doping processes of P1 – P5 in electrochemical experiments were observed, and the proper molecular design for highest occupied molecular orbital (HOMO)/lowest unoccupied molecular orbital (LUMO) levels of P1 – P5 induced the highest photovoltaic open‐circuit voltage in the PSC devices, compared with those previously reported CPDT‐based narrow‐band‐gap polymers. Powder X‐ray diffraction (XRD) analyses suggested that these copolymers formed self‐assembled π‐π stacking and pseudobilayered structures. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers P1 – P5 mixed with electron acceptor [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) in the weight ratio of 1:4 were investigated. The PSC device containing P1 gave the best preliminary result with an open‐circuit voltage of 0.84 V, a short‐circuit current of 2.36 mA/cm², and a fill factor of 0.38, offering an overall power conversion efficiency (PCE) of 0.77% as well as a maximal quantum efficiency of 23% from the external quantum efficiency (EQE) measurements. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2073–2092, 2009     

Synthesis and characterization of fluorene‐based low‐band gap copolymers containing propylenedioxythiophene and benzothiadiazole derivatives for bulk heterojunction photovoltaic cell applications

The following noble series of soluble π‐conjugated statistical copolymers was synthesized by palladium catalyzed Suzuki polymerization: poly[(9,9‐dioctylfluorene)‐alt‐(4,7‐bis(3′,3′‐dihepyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole)] (PFO‐PTBT) derived from poly(9,9‐dioctylfluorene) (PFO) and poly[(4,7‐bis(3′,3′‐dihepyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole)] poly(heptyl₄‐PTBT). The structure and properties of these polymers were characterized using ¹H‐, ¹³C‐NMR, UV–visible spectroscopy, elemental analysis, GPC, DSC, TGA, photoluminescence (PL), and cyclic voltammetry (CV). The statistical copolymers, PFO‐PTBT (9:1, 8.4:1.6, 6.5:3.5), were soluble in common organic solvents and easily spin coated onto indium‐tin oxide (ITO) coated glass substrates. The weight‐average molecular weight (M_w) and polydispersity of the PFO‐PTBT ranged from (1.0–4.2) × 10⁴ and 1.5–2.3, respectively. Bulk heterojunction photovoltaic cells with an ITO/PEDOT/PFO‐PTBT:PCBM/LiF/Al configuration were fabricated, and the devices using PFOPTBT (6.5:3.5) showed the best performance compared with those using PFO‐PTBT (9:1, 8.4:1.6). A maximum power conversion efficiency (PCE) of 0.50% (V_oc = 0.66 V, FF = 0.29) was achieved with PFO‐PTBT (6.5:3.5). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6175–6184, 2008     

Synthesis of block copolymers comprised of poly(3‐hexylthiophene) segment with trisiloxane side chains and their application to organic thin film transistor

The demand of stretchability for a semiconducting polymer has increased to realize wearable devices and sensors. However, studies involving intrinsically stretchable π‐conjugated polymers are still limited. Here, we develop a soft‐polythiophene derivative, P3SiHT, with a trisiloxane unit in the side chains via a hexylene spacer unit. In addition, diblock (P3HT‐b‐P3SiHT) and triblock (P3HT‐b‐P3SiHT‐b‐P3HT) copolymers could be synthesized based on Kumada catalyst‐transfer polycondensation. The results of atomic force microscopy and grazing incidence small‐angle X‐ray scattering indicate that the block copolymer thin films form a phase‐separated structure between the P3HT and P3SiHT domains. The organic thin film transistor devices were prepared to assess the electrical properties of the block polymers. As a result, the block copolymers showed comparable or even higher hole mobility than that of P3HT homopolymer, thus due to the enhanced phase‐separation and thereby charge transportation. The mechanical test of the bulk films indicates that P3HT‐b‐P3SiHT‐b‐P3HT shows lower tensile modulus and longer elongation at break than P3HT homopolymer and other diblock copolymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1787–1794     

Synthesis and photovoltaic properties of conjugated D–A copolymers based on thienyl substituted pyrene and diketopyrrolopyrrole for polymer solar cells

A new donor‐acceptor conjugated copolymer (PDTPyDPP), comprising 2,7‐di‐2‐thienyl‐4,5,9,10‐tetrakis(hexyloxy)pyrene as a donor and diketopyrrolopyrrole (DPP) as an acceptor, was synthesized. PDTPyDPP showed good solubility in common organic solvents, broad visible absorption from 300 to 900 nm, and a moderate hole mobility up to 6.3 × 10^?3 cm² V^?1 s^?1. The power conversion efficiency of the photovoltaic device based on the PDTPyDPP/PC₇₁BM photoactive layer reached 4.43% with 0.66 V of open‐circuit voltage (V_oc), 10.52 mA cm^?2 of short‐circuit current (J_sc) and 64.11% of fill factor. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3198–3204     

Low band‐gap D–A conjugated copolymers based on anthradithiophene and diketopyrrolopyrrole for polymer solar cells and field‐effect transistors

Two conjugated copolymers PADT‐DPP and PADT‐FDPP based on anthradithiophene and diketopyrrolopyrrole, with thiophene and furan as the π‐conjugated bridge, respectively, were successfully synthesized and characterized. The number‐averaged molecular weights of the two polymers are 38.7 and 30.2 kg/mol, respectively. Polymers PADT‐DPP and PADT‐FDPP exhibit broad absorption bands and their optical band gaps are 1.44 and 1.50 eV, respectively. The highest occupied molecular orbital energy level of PADT‐DPP is located at ?5.03 eV while that of PADT‐FDPP is at ?5.16 eV. In field‐effect transistors, PADT‐DPP and PADT‐FDPP displayed hole mobilities of 4.7 × 10^?3 and 2.7 × 10^?3 cm²/(V s), respectively. In polymer solar cells, PADT‐DPP and PADT‐FDPP showed power conversion efficiency (PCE) of 3.44% and 0.29%, respectively. Atomic force microscopy revealed that the poor efficiency of PADT‐FDPP should be related to the large two‐phase separation in its active layer. If 1,8‐diiodooctane (DIO) was used as the solvent additive, the PCE of PADT‐DPP remained almost unchanged due to very limited morphology variation. However, the addition of DIO could remarkably elevate the PCE of PADT‐FDPP to 2.62% because of the greatly improved morphology. Our results suggest that the anthradithiophene as an electron‐donating polycyclic system is useful to construct new D–A alternating copolymers for efficient polymer solar cells. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1652–1661     

All-polymer solar cells utilizing low band gap polymers as donor and acceptor

All-polymer solar cells based on blends of the low band gap polymers poly{[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]} (PTB7) and poly{[N,N-9-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,59-(2,29-bithiophene)} (P(NDI2OD-T2)) are demonstrated. The use of the donor polymer PTB7 instead of poly(3-hexylthiophene) results in a higher open-circuit voltage and an overall spectral response better matched to the solar spectrum. A power conversion efficiency of 1.1% is reported with a peak external quantum efficiency of 18% at a wavelength of 680 nm. The microstructure of PTB7:P(NDI2OD-T2) blends is also investigated using a combination of grazing-incidence wide-angle X-ray scattering (GIWAXS), near-edge X-ray fine-structure (NEXAFS) spectroscopy, atomic force microscopy (AFM), and scanning transmission X-ray microscopy (STXM). GIWAXS measurements show that PTB7:P(NDI2OD-T2) blends contain P(NDI2OD-T2) crystallites with a (100) thickness of 9.5 nm dispersed in an amorphous PTB7 matrix. STXM measurements indicate a lack of mesoscale phase separation, with AFM and NEXAFS measurements revealing a P(NDI2OD-T2)-rich top surface with fibrillar morphology. These results indicate that the pairing of low band gap polymers as both donor and acceptor polymers in all-polymer solar cells may be an effective strategy for realizing high-efficiency all-polymer solar cells. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Benzodifuran‐containing well‐defined π‐conjugated polymers for photovoltaic cells

Two well‐defined alternating π‐conjugated polymers containing a soluble electroactive benzo[1,2‐b:4,5‐b′]difuran (BDF) chromophore, poly(BDF‐(9‐phenylcarbazole)) (PBDFC), and poly(BDF‐benzothiadiazole) (PBDFBTD) were synthesized via Sonogashira copolymerizations. Their optical, electrochemical, and field‐effect charge transport properties were characterized and compared with those of the corresponding homopolymer PBDF and random copolymers of the same overall composition. All these polymers cover broad optical absorption ranges from 250 to 750 nm with narrow optical band gaps of 1.78–2.35 eV. Both PBDF and PBDFBTD show ambipolar redox properties with HOMO levels of ?5.38 and ?5.09 eV, respectively. The field‐effect mobility of holes varies from 2.9 × 10^?8 cm² V^?1 s^?1 in PBDF to 1.0 × 10^?5 cm² V^?1 s^?1 in PBDFBTD. Bulk heterojunction solar cell devices were fabricated using the polymers as the electron donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as the electron acceptor, leading to power conversion efficiencies of 0.24–0.57% under air mass 1.5 illumination (100 mW cm^?2). These results indicate that their band gaps, molecular electronic energy levels, charge mobilities, and molecular weights are readily tuned by copolymerizing the BDF core with different π‐conjugated units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of new selenophene‐based conjugated polymers for organic photovoltaic cells

Three new polymers poly(3,4′′′‐didodecyl) hexaselenophene) (P6S), poly(5,5′‐bis(4,4′‐didodecyl‐2,2′‐biselenophene‐5‐yl)‐2,2′‐biselenophene) (HHP6S), and poly(5,5′‐bis(3′,4‐didodecyl‐2,2′‐biselenophene‐5‐yl)‐2,2′‐biselenophene) (TTP6S) that have the same selenophene‐based polymer backbone but different side chain patterns were designed and synthesized. The weight‐averaged molecular weights (M_w) of P6S, HHP6S, and TTP6S were found to be 19,100, 24,100, and 19,700 with polydispersity indices of 2.77, 1.48, and 1.41, respectively. The UV–visible absorption maxima of P6S, HHP6S, and TTP6S are at 524, 489, and 513 nm, respectively, in solution and at 569, 517, and 606 nm, respectively, in the film state. The polymers P6S, HHP6S, and TTP6S exhibit low band gaps of 1.74, 1.95, and 1.58 eV, respectively. The field‐effect mobilities of P6S, HHP6S, and TTP6S were measured to be 1.3 × 10^?4, 3.9 × 10^?6, and 3.2 × 10^?4 cm² V^?1 s^?1, respectively. A photovoltaic device with a TTP6S/[6,6]‐phenyl C₇₁‐butyric acid methyl ester (1:3, w/w) blend film active layer was found to exhibit an open circuit voltage (V_OC) of 0.71 V, a short circuit current (J_SC) of 5.72 mA cm^?2, a fill factor of 0.41, and a power conversion efficiency (PCE) of 1.67% under AM 1.5 G (100 mW cm^?2) illumination. TTP6S has the most planar backbone of the tested polymers, which results in strong π–π interchain interactions and strong aggregation, leading to broad absorption, high mobility, a low band gap, and the highest PCE. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Role of balanced charge carrier transport in low band gap polymer:Fullerene bulk heterojunction solar cells

Lowering of the optical band gap of conjugated polymers in bulk heterojunction solar cells not only leads to an increased absorption but also to an increase of the optimal active layer thickness due to interference effects at longer wavelengths. The increased carrier densities due to the enhanced absorption and thicker active layers make low band gap solar cells more sensitive to formation of space charges and recombination. By systematically red shifting the optical parameters of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐p‐phenylenevinylene] and 6,6‐phenyl C₆₁‐butyric acid methyl ester, we simulate the effect of a reduced band gap on the solar cell efficiencies. We show that especially the fill factor of low band gap cells is very sensitive to the balance of the charge transport. For a low band gap cell with an active layer thickness of 250 nm, the fill factor of 50% for balanced transport is reduced to less than 40% by an imbalance of only one order of magnitude. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

3,6‐Dialkylthieno[3,2‐b]thiophene moiety as a soluble and electron donating unit preserving the coplanarity of photovoltaic low band gap copolymers

It has been shown recently, that the presence of alkyl side chains at the 3‐positions on the thiophene rings placed next to 2,1,3‐benzothiadiazole core in the backbone of several conjugated polymers results in severe steric hindrance and prevents efficient planarity of the thiophene‐2,1,3‐benzothiadiazole‐thiophene (TBzT) segment. Both properties have a strong influence on the optoelectronic properties of the polymer and need to be considered when the polymer is to be used for organic electronics applications. In this work, we modified a previously synthesized oligothiophene copolymer, consisting of two 3,4′‐dialkyl‐2,2′‐bithiophene units attached to a 2,1,3‐benzothiadiazole unit (TBzT segment) and a thieno[3,2‐b]thiophene unit, by optimizing the lateral alkyl side chains following a density functional theory investigation. It is demonstrated that eliminating the alkyl side chains from the 3‐positions of the TBzT segment and anchoring them onto the thieno[3,2‐b]thiophene, using an efficient synthesis of the 3,6‐dihexylthieno[3,2‐b]thiophene unit, allows us to reduce the energy band gap. In addition, the chemical modification leads to a better charge transport and to an enhanced photovoltaic efficiency of polymer/fullerene blends. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Toward low‐band gap dithienophosphole copolymers for an application in organic solar cells

Two functionalized dithieno[3,2‐b:2′,3′‐d]phospholes with solubilizing groups have been synthesized that allow for the generation of a series of π‐conjugated AB‐ and ABC‐copolymers. The polymers obtained show notable optoelectronic properties with red‐shifted absorption and emission in the orange to red section of the optical solar spectrum. Although combination of dithienophosphole units with fluorene building blocks gives access to processable polymers with band gaps between 2.2 and 2.3 eV in solution and 2.0 eV in the solid state, an ABC copolymer based on dithienophosphole, fluorene, and bis(thienyl)benzothiadiazole units was found to not only exhibit a suitable band gap for solar cell applications (solution: 2.0 eV; solid state: 1.7 eV) but also showed good solubility as well as good electron transfer properties in the presence of fullerene (C₆₀). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8179–8190, 2008     

Synthesis and characterization of cyclopentadithiophene‐based low bandgap copolymers containing electron‐deficient benzoselenadiazole derivatives for photovoltaic devices

We have synthesized two cyclopentadithiophene (CDT)‐based low bandgap copolymers, poly[(4,4‐bis(2‐ethyl‐hexyl)‐4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophene‐2,6‐diyl)‐alt‐(benzo[c][1,2,5]selenadiazole‐4,7‐diyl)] (PCBSe) and poly[(4,4‐bis(2‐ethyl‐hexyl)‐4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophene‐2,6‐diyl)‐alt‐(4,7‐dithiophen‐2‐yl‐benzo[c][1,2,5]selenadiazole‐5,5′‐diyl)] (PCT2BSe), for use in photovoltaic applications. Through the internal charge transfer interaction between the electron‐donating CDT unit and the electron‐accepting benzoselenadiazole, we realized exceedingly low bandgap polymers with bandgaps of 1.37–1.46 eV. The UV–vis absorption maxima of PCT2BSe were subjected to larger hypsochromic shifts than those of PCBSe, because of the distorted electron donor–acceptor (D–A) structures of the PCT2BSe backbone. These results were supported by the calculations of the D–A complex using the ab initio Hartree‐Fock method with a split‐valence 6‐31G* basis set. However, PCT2BSe exhibited a better molar absorption coefficient in the visible region, which can lead to more efficient absorption of sunlight. As a result, PCT2BSe blended with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) exhibited a better photovoltaic performance than PCBSe because of the larger spectral overlap integral with respect to the solar spectrum. Furthermore, when the polymers were blended with PC₇₁BM, PCT2BSe showed the best performance, with an open circuit voltage of 0.55 V, a short‐circuit current of 6.63 mA/cm², and a power conversion efficiency of 1.34% under air mass 1.5 global illumination conditions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1423–1432, 2010     

A wide band gap polymer derived from 3,6‐carbazole and tetraphenylsilane as host for green and blue phosphorescent complexes

We have synthesized a novel wide band gap polymer P36HCTPSi derived from 3,6‐carbazole and tetraphenylsilane by palladium‐catalyzed Suzuki coupling reaction. The resultant polymer shows a high glass transition temperature (217 °C) and good thermal stability. The conjugation length of P36HCTPSi is effectively confined because of the δ‐Si interrupted polymer backbone. The polymer exhibits a violet emission with a peak at 392 nm in solution, and the band gap estimated from the onset of its absorption is 3.26 eV. The high energy emission and wide band gap of P36HCTPSi make it appropriate host for green and blue emission phosphorescent materials. Efficient energy transfers from P36HCTPSi to both fac‐tris[2‐(2‐pyridyl‐kN)‐5‐methylphenyl]iridium(III) (green emission) and bis[(4,6‐difluorophenyl)pyridinato‐N,C²]‐(picolinato)iridium(III) (blue emission) were observed in photoluminescence (PL) spectra. Highly efficient phosphorescent polymer light‐emitting devices were realized by using P36HCTPSi as the host for iridium complexes, the maximum luminous efficiencies for green and blue devices were 27.6 and 3.4 cd/A, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4784–4792, 2009