Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Synthesis and properties of novel sulfonated polyimides from 2,2′‐bis(4‐aminophenoxy)biphenyl‐5,5′‐disulfonic acid

Novel sulfonated polyimides (SPIs) were prepared from 1,4,5,8‐naphthalenetetracarboxylic dianhydride (NTDA), 2,2′‐bis(4‐aminophenoxy)biphenyl‐5,5′‐disulfonic acid (oBAPBDS) with nonlinear configuration, and common nonsulfonated diamines. Water uptake (WU) in liquid and vapor, water stability, and proton conductivity σ of the resulting SPI membranes were investigated. They were soluble in m‐cresol and dimethylsulfoxide, and their WUs in liquid were much larger than those of the SPIs from other sulfonated diamines with linear configuration such as 4,4′‐bis(4‐aminophenoxy)biphenyl‐3,3′‐disulfonic acid (BAPBDS). NTDA‐oBAPBDS membrane was soluble in water at room temperature, whereas all the oBAPBDS‐based copolyimide membranes were insoluble in water and maintained mechanical strength after being soaked in distilled water at 80 °C for 40–1000 h. This much improved water stability was due to the enhanced solubility stability of membrane toward water. The water vapor sorption isotherms were rather similar between the SPIs with the nonlinear and linear configurations of sulfonated diamine moieties. The present SPIs with IECs of 1.8–2.6 meq/g, including NTDA‐BAPBDS, showed reasonably high proton conductivities under the highly humid conditions and roughly fell on the same σ–WU relation line. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1432–1440, 2004     

Sulfonated poly(meta‐phenylene isophthalamide)s as proton exchange membranes

Random and block sulfonated poly(meta‐phenylene isopthalamide)s as proton exchange membranes were synthesized through the Higashi‐Yamazaki phosphorylation method. Polymers with different degrees of sulfonation from 40 to 100 mol percent were prepared by adjusting the molar feed ratio of 5‐sulfoisophthalic acid sodium salt (SIPA) and isophthalic acid (IPA) in the reaction with meta‐phenylene diamine. Creasable polymer films were obtained by casting DMSO polymer solutions and the membrane films could be exchanged to the proton form in strong acid. ¹H NMR spectroscopy and titration confirmed the degree of sulfonation. Thermogravimetric analysis demonstrated good thermal stabilities with 5% weight loss greater than 380 °C. The copolymers with low degrees of sulfonation (DS = 40 mol %) exhibited low water uptake (water uptake < 17 wt %) at room temperature. A segmented multiblock copolymer prepared by preforming a sulfonated block showed lower water uptake at high temperatures than the random polymer with the same DS of 40 mol % and displayed stability in water up to 80 °C. Both random and block copolymers showed higher proton conductivities at high temperature than that of Nafion‐117 under 95% relative humidity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2582–2592     

Selectively sulfonated poly(aryl ether sulfone)‐b‐polybutadiene for proton exchange membrane

A series of selectively sulfonated poly(arylene ether sulfone)‐b‐polybutadiene copolymers (SPAES‐b‐PB) were prepared based on carboxyl terminated polybutadiene (CTPB) and sulfonated poly(arylene ether sulfone) (SPAES) that was directly prepared by polycondensation of 4,4′‐isopropylidenediphenol with different molar ratios of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS) to 4,4′‐dichlorodiphenylsulfone (DCDPS), and subsequent selective postsulfonation of flexible PB block was carried out. Epoxidized modification of membranes was conducted by an in situ‐generated peracid method. The content of sulfonic acid groups attaching to aromatic rings in SPAES was determined by ¹H NMR and was in good aggrement with the controlled ratios. The effect of sulfonated rigid blocks on the postsulfonation of PB blocks was studied by Fourier transform infrared spectroscopy. The glass transition temperature (T_g) and the temperature of the melting peak (T) of membranes in acid form were studied by differential scanning calorimetry. Fenton's reagent test revealed that the selectively sulfonated SPAES‐b‐PB membranes had good stability to oxidation. The microstructure of rod‐like rigid SPAES blocks and interpenetrating network of ions were observed by transmission electron microscopy. Complex impedance measurement showed that an epoxidized membrane with SPAES‐40 exhibited the highest proton conductivity (1.08 × 10^?1 S/cm, 90 °C), which was due to the formation of obvious ionic networks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 665–672, 2006     

Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Membranes from poly(aryl ether)‐based ionomers containing multiblock segments of randomly distributed nanoclusters of 18 sulfonic acid groups

Multiblock copolymers 1a (M_n = 31,500–47,400) of sulfonated poly(aryl ether)s were synthesized by polycondensation of 4,4′‐difluorobenzophenone (DFBP), bis(4‐hydroxyphenyl)sulfone (BHPS), and an hydroxy‐terminated sulfonated oligomer, which was synthesized from DFBP and 2,2′,3,3′,5,5′‐hexaphenyl‐4,4′‐dihydroxybiphenyl a . The copolymerization of trimeric monomer b with DFBP and BHPS gave a series of copolymers 1b (M_n = 26,200–45,900). The copolymers were then sulfonated with chlorosulfonic acid to give ionomers 3a with hydrophilic multiblock segments and ionomers 3b with segments containing clusters of 18 sulfonic acid groups. The proton exchange membranes cast from ionomers 3a and 3b were characterized with regard to thermal stability, water uptake, proton conductivity, and morphology. Transmission electron microscopy images of 3a‐1 and 3b‐1 revealed a phase separation similar to that of Nafion that may explain their higher proton conductivities compared with randomly sulfonated copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4762–4773, 2009     

Novel multiblock‐co‐ionomers as potential polymer electrolyte membrane materials

In this contribution a series of novel multiblock‐co‐ionomers consisting of hydrophobic (partially fluorinated) and hydrophilic (sulfonated) domains has been prepared and characterised in terms of their applicability as fuel cell membranes. The synthesis of these multiblock‐co‐ionomers is a four‐step procedure including (1) the sulfonation of the monomer 4,4′‐difluorodiphenylsulfone, (2) the preparation of hydrophilic telechelic macromonomers by molecular‐weight controlled step‐growth polycondensation of the sulfonated monomer with various bis(thio)phenols, (3) the preparation of a hydrophobic telechelic macromonomer and (4) the coupling of both telechelic macromonomers to yield microphase‐separated block‐co‐ionomers. This study focuses on the investigation of the influence of various linkage groups and atoms within the hydrophilic domains of the multiblock‐co‐ionomers. Both the telechelic macromonomers and the multiblock‐co‐ionomers were structurally investigated by ¹H‐ and ¹⁹F‐NMR spectroscopy and gel permeation chromatography (GPC). All multiblock‐co‐ionomers of this series could be cast into membranes and their membrane properties (ion‐exchange capacity, specific resistance, swelling ratio, water uptake, thermal and oxidative stability) were measured and discussed in dependence of the various linkage groups within the hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5237–5255, 2007     

Phosphoric acid‐doped imidazolium ionomers with enhanced stability for anhydrous proton‐exchange membrane applications

Phosphoric acid‐doped crosslinked proton‐conducting membranes with high anhydrous proton conductivity, and good chemical stability in phosphoric acid were synthesized and characterized. The synthetic procedure of the acid‐doped composite membranes mainly involves the in situ crosslinking of polymerizable monomer oils (styrene and acrylonitrile) and vinylimidazole, and followed by the sulfonation of pendant imidazole groups with butanesultone, and further doped with phosphoric acid. The resultant phosphoric acid‐doped composite electrolyte membranes are flexible and show high thermal stability and high‐proton conductivity up to the order of 10^?2 S cm^?1 at 160 °C under anhydrous conditions. The phosphoric acid uptake, swelling degree, and proton conductivity of the composite membranes increase with the vinylimidazole content. The resultant composite membranes also show good oxidative stability in Fenton's reagent (at 70 °C), and quite good chemical stability in phosphoric acid (at 160 °C). The properties of the prepared electrolyte membranes indicate their promising prospects in anhydrous proton‐exchange membrane applications. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 , 51, 1311–1317     

Proton‐conductive membranes based on blends of polyimides

We prepared novel proton‐conductivity membranes based on blends of sulfonated polyimides. The blend membranes were prepared from a sulfonated homopolyimide and a sulfonated copolyimide with a solvent‐casting method. The proton conductivities of the blend membranes were measured as functions of the temperature with four‐point‐probe electrochemical impedance spectroscopy. The conductivity of the membranes strongly depended on the sulfonated homopolyimide content and increased with an increase in the content. The proton conductivity of all the blended membranes indicated a higher value than that determined in Nafion at 80 °C, and this may mean that the proton transfer in the blend membranes is responsible for the ionic channels induced by the hydrophobic and hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1325–1332, 2007     

Effect of the initial matrix material on the structure of radiation‐grafted ion‐exchange membranes: Wide‐angle and small‐angle X‐ray scattering studies

Seven different fluoropolymer films were used as matrix materials for radiation‐grafted ion‐exchange membranes. The crystallinity and preferred orientation of these membranes were studied with wide‐angle X‐ray scattering, and the lamellar structure of the membranes was examined with small‐angle X‐ray scattering. The crystallinity of poly(vinylidene fluoride) (PVDF)‐based matrix materials varied between 57 and 40%, and the crystallinity of the sulfonated samples varied between 34 and 23%. The lamellar periods of PVDF‐based matrix materials were about 115 Å, and the lamellar periods of poly(ethylene‐alt‐tetrafluoroethylene) and poly(tetrafluoroethylene‐co‐hexafluoropropylene) were 250 and 212 Å, respectively. When the samples were grafted, the lamellar periods increased. Correlation function analysis showed very clearly that the long‐range order decreased because of grafting and sulfonation processes. For those samples that showed good proton conductivity, the lamellar period also increased because of sulfonation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1539–1555, 2002     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Polysulfone ionomers functionalized with benzoyl(difluoromethylenephosphonic acid) side chains for proton‐conducting fuel‐cell membranes

Polysulfones carrying benzoyl(difluoromethylenephosphonic acid) side chains were prepared and investigated for use as proton‐conducting fuel‐cell membranes. In the first step, polysulfones were lithiated and reacted with methyl iodobenzoates to prepare p‐ and o‐iodobenzoyl polysulfones. Next, the phosphonated polysulfones were prepared via CuBr‐mediated cross‐coupling reactions between the iodinated polymer and [(diethoxyphosphinyl)difluoromethyl]zinc bromide. Finally, dealkylation with bromotrimethylsilane afforded highly acidic ? CF₂? PO₃H₂ derivatives. The replacement of the iodine atoms by ? CF₂? PO₃Et₂ units was almost quantitative in the case of o‐iodobenzoyl polysulfone. Membranes based on ionomers having 0.90 mmol of phosphonic acid units/g of dry polymer took up 6 wt % water when immersed at room temperature, and conductivities up to 5 mS cm^?1 at 100 °C were recorded. This level of conductivity was comparable to that reached by a membrane based on a sulfonated polysulfone having 0.86 mmol of sulfonic acid/g of dry polymer. Thermogravimetry revealed that the aryl? CF₂? PO₃H₂ arrangement decomposed at approximately 230 °C via cleavage of the C? P bond. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 269–283, 2007.     

Proton‐conducting electrolytes based on silylated and sulfonated polyetheretherketone: Synthesis and characterization

A derivative of polyetheretherketone (PEEK) having sulfonic acid groups and silicon‐containing substituents covalently bound to the aromatic backbone has been prepared as proton‐exchange membrane material. The polymer 4 (PhSiSPEEK) has been synthesized via (i) sulfonation of PEEK up to 0.9 degree of sulfonation (DS, the number of sulfonic groups per repeat unit), (ii) conversion of sulfonated PEEK 1 (SPEEK09) into sulfonyl chlorinated derivative 2 (PEEKSO₂Cl), (iii) lithiation of 2 and subsequent addition of PhSiCl₃, followed by hydrolysis. The chemical structure of the synthesized polymers has been investigated by ¹H NMR and ¹³C NMR and ATR/FTIR spectroscopy and their thermal stability has been evaluated by thermogravimetric analysis. The presence of inorganic moieties increases the thermal stability of 4 with respect to the sulfonated and not silylated product. Despite its very high DS, PhSiSPEEK is insoluble in water but does not possess the plastic properties needed to be used as an electrolyte membrane. Blend membranes made of SPEEK05 (DS = 0.5) and containing 10 and 25 wt % of 4 (DS = 0.9, degree of silylation DSi = 0.1) have been prepared and characterized by water uptake measurements and electrochemical impedance spectroscopy. The combination of the two functionalized polymers having different properties allows to obtain proton‐conducting electrolytes that are potential candidates for fuel cells applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2178–2186, 2010     

Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Fourier transform infrared/attenuated total reflectance analysis of water diffusion in poly[styrene‐b‐isobutylene‐ b‐styrene] block copolymer membranes

A Fourier transform infrared/attenuated total reflectance technique was used to study the diffusion of water through poly(styrene‐b‐isobutylene‐b‐styrene) block copolymers (BCPs), as well as sulfonated (H⁺) and Na⁺‐sulfonated ionomer versions. Diffusion data were collected and interpreted for these membranes versus polystyrene block composition, degree of sulfonation, Na⁺ ion content in the ionomers, and the effect of initially dry versus prehydrated conditions. An “early time” diffusion coefficient, D, decreased with increasing percent polystyrene for a series of unmodified BCPs. D decreased with increasing degree of sulfonation, and with increasing ion content for the Na⁺‐exchanged samples and this was interpreted in terms of diffusion limitations caused by a strong tendency for ion hydration. The method also yielded information relating to the time evolution of water structure from the standpoint of degree of intermolecular hydrogen bonding. Membrane prehydration causes profound increases in D for both the unmodified BCP and sulfonated samples, as in plasticization. The simultaneous acquisition of information relating to interactions between water molecules and interactions of water molecules with functional groups on the host polymer matrix offers more information than conventional diffusion measurement techniques that simply count transported molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 764–776, 2005     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104