Cellulose Acetate–Poly(N‐isopropylacrylamide)‐Based Functional Surfaces with Temperature‐Triggered Switchable Wettability

Temperature‐triggered switchable nanofibrous membranes are successfully fabricated from a mixture of cellulose acetate (CA) and poly(N‐isopropylacrylamide) (PNIPAM) by employing a single‐step direct electrospinning process. These hybrid CA‐PNIPAM membranes demonstrate the ability to switch between two wetting states viz. superhydrophilic to highly hydrophobic states upon increasing the temperature. At room temperature (23 °C) CA‐PNIPAM nanofibrous membranes exhibit superhydrophilicity, while at elevated temperature (40 °C) the membranes demonstrate hydrophobicity with a static water contact angle greater than 130°. Furthermore, the results here demonstrate that the degree of hydrophobicity of the membranes can be controlled by adjusting the ratio of PNIPAM in the CA‐PNIPAM mixture.

     

Synthesis and characterization of “Living” star‐shaped poly(N‐vinylcaprolactam) with four arms and carboxylic acid end groups

Poly(N‐vinylcaprolactam) (PNVCL) star‐shaped polymers with four arms and carboxyl end groups were synthesized by reversible addition–fragmentation chain transfer (RAFT) polymerization of N‐vinylcaprolactam (NVCL) employing a tetrafunctional trithiocarbonate as an R‐RAFT agent. The resulting star polymers were characterized using ¹H NMR, FT‐IR, gel permeation chromatography (GPC), and UV–vis. Molecular weight of star polymers were analyzed by GPC and UV–vis being observed that the values obtained were very similar. Furthermore, the thermosensitive behavior of the star polymers was studied in aqueous solution by measuring the lower critical solution temperature by dynamic light scattering. Star‐shaped PNVCL were chain extended with ethyl‐hexyl acrylate (EHA) to yield star PNVCL‐b‐PEHA copolymers with an EHA molar content between 4% and 6% proving the living character of the star‐shaped macroCTA. These star block copolymers form aggregates in aqueous solutions with a hydrodynamic diameter ranged from 170 to 225 nm. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2156–2165     

Stimuli-responsive chitosan-graft-poly(N-vinylcaprolactam) as a promising material for controlled hydrophobic drug delivery

A novel type of pH- and thermo-responsive copolymer, chitosan-graft-poly(N-vinylcaprolactam) (chitosan-g-PNVCL), was prepared by grafting carboxyl-terminated poly(N-vinylcaprolactam) (PNVCL-COOH) chains onto a chitosan backbone as a drug-delivery carrier. The formation of chitosan-g-PNVCL was confirmed by FT-IR and 1H NMR techniques. Chitosan-g-PNVCL showed a definite phase transition at 32 degrees C as occurs in pure PNVCL. The swelling degree of the chitosan-g-PNVCL beads was found to be higher at pH 2.2 than at pH 7.4. Moreover, the swelling degree of the beads decreased with increased environmental temperature. Compared to the chitosan beads, the release profile of chitosan-g-PNVCL beads showed a slower and more controlled release of the entrapped ketoprofen. The release behavior of the chitosan-g-PNVCL beads was influenced by both the pH and temperature of the medium. The MTT assay showed no obvious cytotoxicity of chitosan-g-PNVCL against a human endothelial cell line over a concentration range of 0-400 microg x mL(-1). These results suggest that chitosan-g-PNVCL could be a potential stimuli-responsive material for controlled drug delivery, and it may improve the bioavailability, efficacy, and compliance of the encapsulated drugs. [Reaction: see text].     

Electrospinning of Hyaluronic Acid (HA) and HA/Gelatin Blends

Summary: In the present study, electrospinning of hyaluronic acid (HA) and hyaluronic acid/gelatin (HA‐GE) blends in N,N‐dimethylformamide (DMF)/water‐mixed solvents have been investigated. When the volume ratio of DMF to water was in the range of 1.5–0.5, HA solutions could be electrospun into fibrous membranes successfully. The average diameter of HA fibers was about 200 nm. The HA‐GE composite nanofibrous membranes with varied HA/GE weight ratio in the range of 100/20–100/100 have also been successfully fabricated. The average diameter of HA‐GE fibers was in the range of 190–500 nm. The decrease in surface tension could promote fiber formation. Thus, an introduction of DMF that could decrease the surface tension distinctively, without significant change or increase in viscosity of the solution, could bypass the use of blowing‐assisted electrospinning. Our postulated picture is that the lower surface tension could help the ejection of stream with relatively high viscosity and reduce or prevent the droplet formation during the spinning process.

HA/GE (100/80) nanofibrous membrane produced by electrospinning.     

Synthesis and self‐assembly of thermosensitive double‐hydrophilic poly(N‐vinylcaprolactam)‐b‐poly(N‐vinyl‐2‐pyrrolidone) diblock copolymers

We report on novel diblock copolymers of poly(N‐vinylcaprolactam) (PVCL) and poly(N‐vinyl‐2‐pyrrolidone) (PVPON) (PVCL‐b‐PVPON) with well‐defined block lengths synthesized by the MADIX/reversible addition‐fragmentation chain transfer (RAFT) process. We show that the lower critical solution temperatures (LCST) of the block copolymers are controllable over the length of PVCL and PVPON segments. All of the diblock copolymers dissolve molecularly in aqueous solutions when the temperature is below the LCST and form spherical micellar or vesicular morphologies when temperature is raised above the LCST. The size of the self‐assembled structures is controlled by the molar ratio of PVCL and PVPON segments. The synthesized homopolymers and diblock copolymers are demonstrated to be nontoxic at 0.1–1 mg mL^?1 concentrations when incubated with HeLa and HEK293 cancer cells for various incubation times and have potential as nanovehicles for drug delivery. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2725–2737     

Dendritic poly(benzyl ether)‐b‐poly(N‐vinylcaprolactam) block copolymers: Self‐organization in aqueous media,thermoresponsiveness and biocompatibility

Four generations of new amphiphilic thermoresponsive linear‐dendritic block copolymers (LDBCs) with a linear poly(N‐vinylcaprolactam) (PNVCL) block and a dendritic poly(benzyl ether) block are synthesized by atom transfer radical polymerization (ATRP) of N‐vinylcaprolactam (NVCL) using dendritic poly(benzyl ether) chlorides as initiators. The copolymers have been characterized by ¹H NMR, FTIR, and GPC showing controlled molecular weight and narrow molecular weight distribution (PDI ≤ 1.25). Their self‐organization in aqueous media and thermoresponsive property are highly dependent on the generation of dendritic poly(benzyl ether) block. It is observed for the LDBCs that the self‐assembled morphology changes from irregularly spherical micelles, vesicles, rod‐like large compound vesicles (LCVs), to the coexistence of spherical micelles and rod‐like LCVs, as the generation of the dendritic poly(benzyl ether) increases. The results of a cytotoxicity study using an MTT assay method with L929 cells show that the LDBCs are biocompatible. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 300–308     

Synthesis of thermo‐responsive poly(N‐vinylcaprolactam)‐containing block copolymers by cobalt‐mediated radical polymerization

Thermo‐responsive block copolymers based on poly(N‐vinylcaprolactam) (PNVCL) have been prepared by cobalt‐mediated radical polymerization (CMRP) for the first time. The homopolymerization of NVCL was controlled by bis(acetylacetonato)cobalt(II) and a molecular weight as high as 46,000 g/mol could be reached with a low polydispersity. The polymerization of NVCL was also initiated from a poly(vinyl acetate)‐Co(acac)₂ (PVAc‐Co(acac)₂) macroinitiator to yield well‐defined PVAc‐b‐PNVCL block copolymers with a low polydispersity (M_w/M_n = 1.1) up to high molecular weights (M_n = 87,000 g/mol), which constitutes a significant improvement over other techniques. The amphiphilic PVAc‐b‐PNVCL copolymers were hydrolyzed into unprecedented double hydrophilic poly(vinyl alcohol)‐b‐PNVCL (PVOH‐b‐PNVCL) copolymers and their temperature‐dependent solution behavior was studied by turbidimetry and dynamic light scattering. Finally, the so‐called cobalt‐mediated radical coupling (CMRC) reaction was implemented to PVAc‐b‐PNVCL‐Co(acac)₂ precursors to yield novel PVAc‐b‐PNVCL‐b‐PVAc symmetrical triblock copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Facile Synthesis of Glycopolypeptides by Combination of Ring‐Opening Polymerization of an Alkyne‐Substituted N‐carboxyanhydride and Click “Glycosylation”

Synthetic glycopolypeptides have attracted much interest for application in biomedical field as they are structural mimics to the natural glycopeptides or glycoproteins. However, the synthesis methods toward glycopolypeptides are still few or less efficient. Herein, we present a facile route to preparation of glycopolypeptides with highly effective “glycosylation” by click postpolymerization modification. First, an alkyne‐substituted N‐carboxyanhydride (NCA) monomer was synthesized and subsequently polymerized to afford the polypeptide with “clickable” alkyne pendants. The alkyne‐functionalized polypeptide was then “glycosylated” by click reaction of different sugar azides to the alkyne pendants with high efficiency. All the obtained glycopolypeptides were soluble and preferred α‐helix conformation in water. Primary studies on the obtained glycopolypeptides binding with Con A lectin were assessed by turbidimetric assay. The more quantitive studies of the interactions between lectin proteins and the synthetic glycopolypeptides, and the application of these materials as the multivalent ligands are in progress.

     

Thermal characterization and solid‐state 13C‐NMR investigation of blends of poly(N‐phenyl‐2‐hydroxytrimethylene amine) and poly(N‐vinyl pyrrolidone)

The miscibility and thermal properties of poly(N‐phenyl‐2‐hydroxytrimethylene amine)/poly(N‐vinyl pyrrolidone) (PHA/PVP) blends were examined by using differential scanning calorimetry (DSC), high‐resolution solid‐state nuclear magnetic resonance (NMR) techniques, and thermogravimetric analysis (TGA). It was found that PHA is miscible with PVP, as shown by the existence of a single composition‐dependent glass transition temperature (T_g) in the whole composition range. The DSC results, together with the ¹³C crosspolarization (CP)/magic angle spinning (MAS)/high‐power dipolar decoupling (DD) spectra of the blends, revealed that there exist rather strong intermolecular interactions between PHA and PVP. The increase in hydrogen bonding and in T_g of the blends was found to broaden the line width of CH—OH carbon resonance of PHA. The measurement of the relaxation time showed that the PHA/PVP blends are homogeneous at least on the scale of 1–2 nm. The proton spin‐lattice relaxation in both the laboratory frame and the rotating frame were studied as a function of the blend composition, and it was found that blending did not appreciably affect the spectral densities of motion (sub‐T_g relaxation) in the mid‐MHz and mid‐KHz frequency ranges. Thermogravimetric analysis showed that PHA has rather good thermal stability, and the thermal stability of the blend can be further improved with increasing PVP content. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 237–245, 1999     

Reversible Thermally Responsive and Luminescent Coil–Rod–Coil Triblock Copolymers

A functional coil–rod–coil triblock copolymer containing a terfluorene unit as the rigid segment and poly(N‐isopropylacrylamide) (PNIPAAm) as the flexible block was successfully synthesized via reversible addition–fragmentation chain‐transfer (RAFT) polymerization using terfluorene‐based dithioester as the RAFT agent. The temperature‐responsive optical properties were investigated with the aid of dynamic light scattering and fluorescence techniques. Additionally, the relationship between the optical properties and the reversible phase transition of the doping system formed by blending the copolymer with tetraphenylporphine tetrasulfonic acid was studied. Above the lower critical solution temperature, the energy transfer efficiency decreased as a result of the globule–to–coil transition from PNIPAAm segments. The result indicates that these copolymers have a potential to be used as responsive fluorescent probes in facile detection of dye‐labeled biopolymers.

     

Scaffolds of Hyaluronic Acid–Poly(Ethyl Acrylate) Interpenetrating Networks: Characterization and In Vitro Studies

Hyaluronic acid (HA) provides many advantages to regenerative implants through its bioactive properties, but it also has many limitations as a biomaterial if it is not chemically modified. In order to overcome some of these limitations, HA has been combined with poly(ethyl acrylate) in the form of interpenetrating polymeric networks (IPNs), in which the HA network is crosslinked with divinyl sulfone. Scaffolds of this IPN have been produced through a template‐leaching methodology, and their properties have been compared with those of single‐network scaffolds made of either PEA or crosslinked HA. A fibroblast cell line has been used to assess the in vitro performance of the scaffolds, revealing good cell response and a differentiated behavior on the IPN surface when compared to the individual polymers. Altogether, the results confirm that this type of material offers an interesting microenvironment for cells, which can be further improved toward its potential use in medical implants.

     

Poly(ethyleneimine)/arginine–glycine–aspartic acid conjugates prepared with N‐succinimidyl 3‐(2‐pyridyldithio)propionate: An investigation of peptide coupling and conjugate stability

Poly(ethylene imine) (PEI), a highly cationic polymer, is being used for deoxyribonucleic acid (DNA) complexation and delivery into cells. To enhance the cellular uptake of polymer/DNA complexes, arginine–glycine–aspartic acid (RGD) peptides have been conjugated to PEI with N‐succinimidyl 3‐(2‐pyridyldithio)propionate (SPDP). This coupling scheme creates a disulfide‐linked conjugate, the stability of which in the presence of thiols is uncertain. We have investigated the conjugation of an RGD peptide, glycine–arginine–glycine–aspartic acid–serine–proline–cysteine (GRGDSPC), to PEI with SPDP and subsequently assessed the stability of the conjugates in the presence of two thiol compounds, mercaptoethanol and cysteine. SPDP effectively controls the extent of GRGDSPC substitution on PEI. The conjugates, however, are readily cleaved in the presence of the thiols; the cleavage is rapid (～50% cleavage in 2–4 h) and inversely related to the degree of peptide substitution on the polymers. The peptide coupling is stable in the absence of thiols, and its cleavage is strongly dependent on the pH of the medium but not on the ionic strength of the medium. We conclude that RGD peptides coupled to PEI are labile in the presence of physiological concentrations of thiols, and this should be taken into account when such polymer–peptide conjugates are used for DNA delivery. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6143–6156, 2004     

Thermoresponsive properties of porous poly(N‐isopropylacrylamide) hydrogels prepared in the presence of nanosized silica particles and subsequent acid treatment

Porous poly(N‐isopropylacrylamide) hydrogels were prepared by the free‐radical polymerization of its monomer and a suitable crosslinker in the presence of spherical silica particles of different sizes (74 and 1600 nm) and by the subsequent acid extraction of silica. The yields were 81–83%, and the yields were not affected by the silica content. Scanning electron microscopy observations revealed the porous structure of the hydrogels. Porous and nonporous hydrogels showed volume phase transitions from swelling states to deswelling states at approximately 30 °C, as analyzed by the ratio of the diameter of cylinder‐shaped hydrogels to that of the glass tube used for the hydrogel preparation at the corresponding temperature. Deswelling, which was analyzed by rapid changes in the temperature of the aqueous media from 20 to 40 °C, was facilitated by decreased silica particle size and increased silica content. The deswelling rate constant of the hydrogel prepared with 74‐nm silica at 10 v/v % (silica/solvent) was more than 1500 times greater than that of conventional hydrogels. Swelling was similarly analyzed through changes in the temperature from 40 to 20 °C and was independent of the pore structure. The deswelling–swelling cycle was repeatable with reasonable reproducibility. Moreover, the mechanical strength of the porous hydrogels was significantly maintained compared with that of conventional nonporous hydrogels. This method produced thermoresponsive hydrogels of suitable mechanical strength and remarkable deswelling properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4228–4235, 2002     

Novel temperature‐ and pH‐responsive graft copolymers composed of poly(L‐glutamic acid) and poly(N‐isopropylacrylamide)

A series of novel temperature‐ and pH‐responsive graft copolymers, poly(L ‐glutamic acid)‐g‐poly(N‐isopropylacrylamide), were synthesized by coupling amino‐semitelechelic poly(N‐isopropylacrylamide) with N‐hydroxysuccinimide‐activated poly(L ‐glutamic acid). The graft copolymers and their precursors were characterized, by ESI‐FTICR Mass Spectrum, intrinsic viscosity measurements and proton nuclear magnetic resonance (¹H NMR). The phase‐transition and aggregation behaviors of the graft copolymers in aqueous solutions were investigated by the turbidity measurements and dynamic laser scattering. The solution behavior of the copolymers showed dependence on both temperature and pH. The cloud point (CP) of the copolymer solution at pH 5.0–7.4 was slightly higher than that of the solution of the PNIPAM homopolymer because of the hydrophilic nature of the poly(glutamic acid) (PGA) backbone. The CP markedly decreased when the pH was lowered from 5 to 4.2, caused by the decrease in hydrophilicity of the PGA backbone. At a temperature above the lower critical solution temperature of the PNIPAM chain, the copolymers formed amphiphilic core‐shell aggregates at pH 4.5–7.4 and the particle size was reduced with decreasing pH. In contrast, larger hydrophobic aggregates were formed at pH 4.2. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4140–4150, 2008     

Thermoresponsive Aggregation Behavior of Triterpene–Poly(ethylene oxide) Conjugates in Water

Bioconjugate amphiphiles comprising triterpene and poly(ethylene oxide) (PEO) were studied according to their thermoresponsive aggregation behavior (LCST) in water. Cholesteryl?PEO (CE) and betulinyl?PEO (BE) comprising <70 wt% PEO precipitated from water upon heating. CE, but not BE, solutions contained nanoscopic aggregates at room temperature causing different thermoprecipitation behaviors. Solutions containing 5 wt% solutions of BE with short PEO chains demonstrated dual thermoresponsive behavior, precipitating at high temperature and forming hydrogel at low temperature. A BE multiblock copolymer was found to form large aggregates, presumably vesicles, in water. Results suggest that the solution properties of triterpene–PEO amphiphiles can be controlled by the chemical composition and structure.

     

SET‐LRP of N,N‐dimethylacrylamide and of N‐isopropylacrylamide at 25 °C in protic and in dipolar aprotic solvents

The single‐electron transfer living radical polymerization (SET‐LRP) of water‐soluble monomers, N,N‐dimethylacrylamide (DMA) and N‐isopropylacrylamide (NIPAM), initiated with 2‐methylchloropropionate (MCP) in dipolar aprotic and protic solvents is reported. The radical polymerization of acrylamides is characterized by higher rate constants of propagation and bimolecular termination than acrylates. Therefore, the addition of CuCl₂ is required to mediate deactivation in the early stages of the reaction. Through the use of Cu(0)‐wire/Me₆‐TREN catalysis, conditions were optimized to minimize the amount of externally added CuCl₂ required to maintain a linear evolution of molecular weight and narrow molecular weight distribution. By using less CuCl₂ additive, the amount of soluble copper species that must ultimately be removed from the reaction mixture is reduced. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1752–1763, 2010     

Formation of a Polypseudorotaxane via Self‐Assembly of γ‐Cyclodextrin with Poly(N‐isopropylacrylamide)

A polypseudorotaxane (PPR) comprising γ‐cyclodextrin (γ‐CD) as host molecules and poly(N‐isopropylacrylamide) (PNIPAM) as a guest polymer is prepared via self‐assembly in aqueous solution. Due to the bulky pendant isopropylamide group, PNIPAM exhibits size‐selectivity toward self‐assembly with α‐, β‐, and γ‐CDs. It can fit into the cavity of γ‐CD to give rise to a PPR, but cannot pass through α‐CD and β‐CD under the same conditions. The ratio of the number of γ‐CD molecules to entrapped NIPAM repeat units is kept at 1:2.2 or 1:2.4, determined by ¹H NMR spectroscopy and TGA analysis, respectively, indicating that there are more than 2 but less than 3 NIPAM repeat units included by one γ‐CD molecule. This finding opens new avenues to PPR‐based supramolecular polymers to be used as solid, stimuli‐responsive materials.     

Synthesis of polydopamine‐coated graphene–polymer nanocomposites via RAFT polymerization

Graphene‐polymer nanocomposites have significant potential in many applications such as photovoltaic devices, fuel cells, and sensors. Functionalization of graphene is an essential step in the synthesis of uniformly distributed graphene‐polymer nanocomposites, but often results in structural defects in the graphitic sp² carbon framework. To address this issue, we synthesized graphene oxide (GO) by oxidative exfoliation of graphite and then reduced it into graphene via self‐polymerization of dopamine (DA). The simultaneous reduction of GO into graphene, and polymerization and coating of polydopamine (PDA) on the reduced graphene oxide (RGO) surface were confirmed with XRD, UV–Vis, XPS, Raman, TGA, and FTIR. The degree of reduction of GO increased with increasing DA/GO ratio from 1/4 to 4/1 and/or with increasing temperature from room temperature to 60 °C. A RAFT agent, 2‐(dodecylthiocarbonothioylthio)?2‐methylpropionic acid, was linked onto the surface of the PDA/RGO, with a higher equivalence of RAFT agent in the reaction leading to a higher concentration of RAFT sites on the surface. Graphene‐poly(methyl methacrylate), graphene‐poly(tert‐butyl acrylate), and graphene‐poly(N‐isopropylacrylamide) nanocomposites were synthesized via RAFT polymerization, showing their characteristic solubility in several different solvents. This novel synthetic route was found facile and can be readily used for the rational design of graphene‐polymer nanocomposites, promoting their applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3941–3949     

Dual stimuli‐responsive microgels based on photolabile crosslinker: Temperature sensitivity and light‐induced degradation

The synthesis and characterization of a new photocleavable crosslinker is presented here. Dual stimuli‐responsive P(VCL‐co‐NHMA) microgels were prepared by precipitation polymerization of vinylcaprolactam (VCL) with N‐hydroxymethyl acrylamide (NHMA) and the new crosslinker. The microgels had distinct temperature sensitivity as observed in the case of PVCL‐based particles and their volume phase transition temperature (VPTT) shifted to higher temperature with increasing NHMA content. Photolytic degradation experiments were investigated by irradiation with UV light, which led to microgel disintegration caused by cleavage of the photolabile crosslinking points. The degradation behavior of the microgels was conducted with respect to degradation rates by means of the relative turbidity changes. Hence, the microgels could totally degrade into short linear polymers by UV light, thus representing a great potential as new light and temperature dual responsive nanoscale materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1676–1685