Living cationic polymerization of amide‐functional vinyl ethers: Specific properties of SnCl4‐based initiating system

Living cationic copolymerization of amide‐functional vinyl ethers with isobutyl vinyl ether (IBVE) was achieved using SnCl₄ in the presence of ethyl acetate at 0 °C: the number–average molecular weight of the obtained polymers increased in direct proportion to the monomer conversion with relatively low polydispersity, and the amide‐functional monomer units were introduced almost quantitatively. To optimize the reaction conditions, cationic polymerization of IBVE in the presence of amide compounds, as a model reaction, was also examined using various Lewis acids in dichloromethane. The combination of SnCl₄ and ethyl acetate induced living cationic polymerization of IBVE at 0 °C when an amide compound, whose nitrogen is adjacent to a phenyl group, was used. The versatile performance of SnCl₄ especially for achieving living cationic polymerization of various polar functional monomers was demonstrated in this study as well as in our previous studies. Thus, the specific properties of the SnCl₄ initiating system are discussed by comparing with the Et_xAlCl_3?x systems from viewpoints of hard and soft acids and bases principle and computational chemistry. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6129–6141, 2008     

Living cationic polymerization of vinyl ethers in the presence of a strong base: Poisonous or helpful?

A quite small dose of a poisonous species was found to induce living cationic polymerization of isobutyl vinyl ether (IBVE) in toluene at 0 °C. In the presence of a small amount of N,N‐dimethylacetamide, living cationic polymerization of IBVE was achieved using SnCl₄, producing a low polydispersity polymer (weight–average molecular weight/number–average molecular weight (M_w/M_n) ≤ 1.1), whereas the polymerization was terminated at its higher concentration. In addition, amine derivatives (common terminators) as stronger bases allow living polymerization when a catalytic quantity was used. On the other hand, EtAlCl₂ produced polymers with comparatively broad MWDs (M_w/M_n ～ 2), although the polymerization was slightly retarded. The systems with a strong base required much less quantity of bases than weak base systems such as ethers or esters for living polymerization. The strong base system exhibited Lewis acid preference: living polymerization proceeded only with SnCl₄, TiCl₄, or ZnCl₂, whereas a range of Lewis acids are effective for achieving living polymerization in the conventional weak base system such as an ester and an ether. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6746–6753, 2008     

Matrix‐assisted laser desorption ionization time of flight mass spectrometry analysis of living cationic polymerization of vinyl ethers. I. Optimization of measurement conditions for poly(isobutyl vinyl ether)

Matrix‐assisted laser desorption ionization time of flight mass spectrometry (MALDI‐TOF‐MS) was utilized for the analysis of polymers obtained by the living cationic polymerization of isobutyl vinyl ether (IBVE) with the HCl‐VE adduct/SnCl₄/n‐Bu₄NCl initiating system in CH₂Cl₂ at −78 °C. Under optimized analysis conditions, well‐resolved spectra were obtained for samples with number‐average molecular weights of ≤10⁴ with the use of 1,8‐dihydroxy‐9(10H)‐anthracenone (dithranol) as a matrix and sodium trifluoroacetate as an added salt. The MS spectra showed only one series of peaks separated exactly by the mass of the IBVE. The observed mass of each peak was in good agreement with the theoretical one, which possesses one initiator fragment at the α end and one methoxy group originated from quenching with methanol at the ω end. Thus, detailed end group analysis is possible for poly(VE). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4023–4031, 2000     

Polymerization of vinyl ethers with transition‐metal catalysts: An examination of the stereoregularity of the formed polymers

The polymerization of isobutyl vinyl ether (IBVE) and tert‐butyl vinyl ether (TBVE) was carried out with metallocene and nonmetallocene catalysts, and the stereoregularity of the formed polymers was examined with ¹³C NMR spectroscopy. IBVE afforded polymers with 63–68% dyad isotacticity by polymerization with mixtures of metallocene catalysts and methyl aluminoxane as a cocatalyst in toluene as a solvent. However, TBVE yielded polymers with 47–52% dyad isotacticity (21–28% triad isotacticity) under the same conditions, the isotacticity being lower than that of poly(isobutyl vinyl ether) (PIBVE). Nonmetallocene catalysts, including Ti, Zr, and Hf complexes with two phenoxy imine chelate ligands, provided PIBVE and poly(tert‐butyl vinyl ether) with 63–68 and 45–51% dyad isotacticity, respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3938–3943, 2002     

Living cationic polymerization of dihydrofuran and its derivatives

Cationic polymerization of 2,3‐dihydrofuran (DHF) and its derivatives was examined using base‐stabilized initiating systems with various Lewis acids. Living cationic polymerization of DHF was achieved using Et_1.5AlCl_1.5 in toluene in the presence of THF at 0 °C, whereas it has been reported that only less controlled reactions occurred at 0 °C. Monomer‐addition experiments of DHF and the block copolymerization with isobutyl vinyl ether demonstrated the livingness of the DHF polymerization: the number–average molecular weight of the polymers shifted higher with low polydispersity as the polymerization proceeded after the monomer addition. Furthermore, this base‐stabilized cationic polymerization system allowed living polymerization of ethyl 1‐propenyl ether and 4,5‐dihydro‐2‐methylfuran at ?30 and ?78 °C, respectively. In the polymerization of 2,3‐benzofuran, the long‐lived growing species were produced at ?78 °C. The obtained polymers have higher glass transition temperatures compared to poly(acyclic alkyl vinyl ether)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4495–4504, 2008     

Cationic polymerization of isobutyl vinyl ether coinitiated with heteropolyacid or its salts in aqueous medium

The suspension cationic polymerization of isobutyl vinyl ether (IBVE) in aqueous medium could be achieved by using H₃PW₁₂O₄₀, AlPW₁₂O₄₀, FePW₁₂O₄₀, K₃PW₁₂O₄₀, or Na₃PW₁₂O₄₀ as efficient water‐tolerant coinitiators in the presence of HCl. The addition reaction of IBVE with H₂O occurred to form IBVE–H₂O adduct and then subsequent decomposition immediately took place or turned to acetaldehyde diisobutyl acetal (A) in the presence of AlPW₁₂O₄₀, and ( A ) decomposed rapidly to form 2‐isobutanol ( B ) and acetaldehyde ( C ). Cationic polymerization of IBVE in aqueous medium was promoted greatly with increasing HCl concentration and proceeded extremely rapidly to get high polymer yield even at low concentration of AlPW₁₂O₄₀ of 0.3 mM. A sufficient amount of HCl was needed to decrease the hydrolysis of initiator IBVE–HCl and to accelerate the polymerization in aqueous medium simultaneously. The yield and molecular weight of poly(IBVE) increased with increasing concentrations of HCl and AlPW₁₂O₄₀ or with decreasing temperature. The isotactic‐rich poly(IBVE)s with m diad of around 60%, having M_n of 1200–4500 g mol^?1 and monomodal molecular weight distribution could be obtained via cationic polymerization of IBVE in aqueous medium. This is the first example of cationic polymerization of IBVE in aqueous medium coinitiated by heteropolyacid and its salts. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Living cationic polymerization of n‐butyl propenyl ether

Cationic polymerization of n‐butyl propenyl ether (BuPE; CH₃CH CHOBu, cis/trans = 64/36) was examined with the HCl–IBVE (isobutyl vinyl ether) adduct/ZnCl₂ initiating system at −15 ∼ −78 °C in nonpolar (hexane, toluene) and polar (dichloromethane) solvents, specifically focusing on the feasibility of its living polymerization. In contrast to alkyl vinyl ethers, the living nature of the growing species in the BuPE polymerization was sensitive to polymerization temperature and solvent. For example, living cationic polymerization of IBVE can be achieved even at 0 °C with HCl–IBVE/ZnCl₂, whereas for BuPE whose β‐methyl group may cause steric hindrance ideal living polymerization occurred only at −78 °C. Another interesting feature of this polymerization is that the polymerization rate in hexane is as large as in dichloromethane, much larger than in toluene. A new method in determining the ratio of the living growing ends to the deactivated ones was developed with a devised monomer‐addition experiments, in which IBVE that can be polymerized in a living fashion below 0 °C was added to the almost completely polymerized solution of BuPE. The amount of the deactivated chain ends became small in hexane even at −40 °C in contrast to other solvents. Thus hexane turned out an excellent solvent for living cationic polymerization of BuPE. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 229–236, 2000     

Stereoregulation in cationic polymerization. III. High isospecificity with the bulky phosphoric acid [(RO)2PO2H]/SnCl4 initiating systems: Design of counteranions via initiators

In the cationic polymerization of isobutyl vinyl ether (IBVE) with binary initiating systems consisting of a protonic acid as an initiator and a Lewis acid as an activator/catalyst, phosphoric acid derivatives [(RO)₂POOH] coupled with SnCl₄ gave highly isotactic poly(IBVE)s, whereas those with a bulky substituent (R), [C₄H₉CH(C₂H₅)CH₂O]₂POOH ( 7 ) and (n‐C₁₀H₂₁)₂POOH ( 8 ), led to the highest isotacticity [meso dyad (m) = 86%]. In contrast, isospecificity was lower with IBVE–HCl and CF₃COOH under the same conditions. From the effects of the polymerization temperature (−78 to 0 °C), it was concluded that the high isospecificity with 7 and 8 was due to an enthalpic factor. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1067–1074, 2001     

Cationic polymerization behavior of isobutyl vinyl ether with arenesulfonates as non‐salt‐type latent thermal initiators

Substituted and unsubstituted benzenesulfonic acid cyclohexyl esters (1–7) were synthesized, and their possibility as latent thermal initiators in the cationic polymerization of isobutyl vinyl ether (IBVE) was examined to develop novel non‐salt type latent cationic initiators. Thermal decomposition of cyclohexyl p‐nitrobenzenesulfonate (2) in C₆D₆ at 80°C proceeded to exclusively afford cyclohexene as well as p‐nitrobenzenesulfonic acid. Cationic polymerization of IBVE with 1 mol % of an arenesulfonate (1–6) in bulk was carried out at 40–100°C for 12 h. No polymerization took place below 50°C, while the consumption of IBVE depending on both the polymerization temperature and the structure of the arenesulfonates was observed above 60°C. The obtained polyIBVEs showed bimodal GPC curves in several cases, revealing the intervention of two independent propagation species in the polymerization. The cationic polymerization of IBVE with cyclohexyl 2,4,6‐triisopropylbenzenesulfonate (7) at 80°C confirmed the acceleration effect of bulkiness on the polymerization rate. It was concluded that the polymerization was largely dependent on both electronic and steric factors of the aryl groups of the initiators which were directly related to the stability of the sulfonate anions. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 293–301, 1999     

Cationic polymerization of isobutyl vinyl ether initiated with transition‐metal ate complexes

The cationic polymerization of isobutyl vinyl ether was examined with transition‐metal ate complexes with trityl cation as initiators. The initiators were generated by the reaction of triphenylmethyl chloride [trityl chloride (TrCl)] with ate complexes of Nb, Mo, and W with lithium cation, which were obtained in situ by the reaction of the transition‐metal halides with anionic reagents (organolithium or lithium amide). When the polymerization was initiated with a mixture of TrCl and Li⁺[NbH₅(NnBuPh)]^?, the resulting poly(isobutyl vinyl ether)s had narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight = 1.13–1.20). Although the polymerization was supposed to be initiated by the electrophilic attack of the trityl cation, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of the resulting poly(isobutyl vinyl ether)s revealed the presence of H at the α‐chain end. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2636–2641, 2006     

Tetradentate schiff base ligand/MCln initiating systems for the controlled cationic polymerization of isobutyl vinyl ether: Effects of the ligand framework

We investigated the cationic polymerization of vinyl ethers using metal complex catalysts with salen and salphen ligands. Metal complexes were generated in situ from the reaction of a ligand and a metal chloride. The choice of a ligand and a central metal was crucial for tuning the catalyst function such as catalytic activity and controllability of the polymerization. Among metal chlorides employed, ZrCl₄ was the most efficient for controlled polymerization. Cationic polymerization of isobutyl vinyl ether (IBVE) proceeded using the salen and salphen‐type ligand/ZrCl₄ initiating systems, yielding polymers with predetermined molecular weights and narrow molecular weight distributions. Importantly, the structural effects of the complex catalysts were responsible for the polymerization behavior. For example, the polymerization using the salen‐type ligand/ZrCl₄ system was much slower than that using the salphen‐type ligand/ZrCl₄ system. In addition, the polymerization of IBVE using the salen‐type ligand/FeCl₃ system proceeded in a controlled manner, which was in contrast to uncontrolled polymerization using the salphen‐type ligand/FeCl₃ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 989–996     

Synthesis of brush‐shaped polymers consisting of a poly(phenylacetylene) backbone and pendant poly(vinyl ether)s via selective reaction of 2‐Vinyloxyethyl 4‐Ethynylbenzoate

We have newly designed an original bifunctional monomer (PAVE) containing both a phenylacetylene (PA) group and a vinyl ether (VE) group, which is expected to be a key material for the synthesis of brush‐shaped polymers consisting of a poly(phenylacetylene) (polyPA) main chain and polyVE side chains. Actually, we have demonstrated the selective chemical transformation of the VE moiety of PAVE to an initiator site for the living cationic polymerization of isobutyl vinyl ether (IBVE), and then succeeded in the controlled synthesis of a novel PA‐end‐capped polyIBVE macromonomer. Moreover, using this macromonomer, the first synthesis of a brush‐shaped polyPA bearing polyVE side chains was achieved via Rh complex‐mediated homopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2800–2805     

Synthesis of biocompatible and biodegradable block copolymers of polyvinyl alcohol‐block‐poly(ε‐caprolactone) using metal‐free living cationic polymerization

Applications of metal‐free living cationic polymerization of vinyl ethers using HCl · Et₂O are reported. Product of poly(vinyl ether)s possessing functional end groups such as hydroxyethyl groups with predicted molecular weights was used as a macroinitiator in activated monomer cationic polymerization of ε‐caprolactone (CL) with HCl · Et₂O as a ring‐opening polymerization. This combination method is a metal‐free polymerization using HCl · Et₂O. The formation of poly(isobutyl vinyl ether)‐b‐poly(ε‐caprolactone) (PIBVE‐b‐PCL) and poly(tert‐butyl vinyl ether)‐b‐poly(ε‐caprolactone) (PTBVE‐b‐PCL) from two vinyl ethers and CL was successful. Therefore, we synthesized novel amphiphilic, biocompatible, and biodegradable block copolymers comprised polyvinyl alcohol and PCL, namely PVA‐b‐PCL by transformation of acid hydrolysis of tert‐butoxy moiety of PTBVE in PTBVE‐b‐PCL. The synthesized copolymers showed well‐defined structure and narrow molecular weight distribution. The structure of resulting block copolymers was confirmed by ¹H NMR, size exclusion chromatography, and differential scanning calorimetry. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5169–5179, 2009     

Living cationic polymerization of isobutyl vinyl ether by the carboxyl group of the carbon black/zinc chloride initiating system

The effect of zinc chloride (ZnCl₂) on the cationic polymerization of isobutyl vinyl ether (IBVE) initiated by carboxyl groups on a carbon black surface was investigated. Although the polymerization of IBVE was initiated by carboxyl groups on the surface, the rate of polymerization was small and the molecular weight distribution (MWD) of poly IBVE was very broad. The rate of the polymerization was found to be drastically increased, and 100% monomer conversion was achieved in a short time by the addition of ZnCl₂. The number-average molecular weights (M_n) of the polyIBVE were directly proportional to monomer conversion in the polymerization initiated by the carbon black/ZnCl₂ system. By addition of the monomer at the end of the first-stage polymerization, the added monomer was smoothly polymerized at the same rate as in the first stage. The M_n of the polymer was in excellent agreement with the calculated value, assuming the polyIBVE chain forms per unit carboxyl group on the surface and MWD was narrow (M_w/M_n = 1.2 ～ 1.3). Based on the results, it is concluded that carbon black/ZnCl₂ system has an ability to initiate the living cationic polymerization of IBVE. Furthermore, it was found that polyIBVE was grafted onto the carbon black surface after the quenching of the living polymer with methanol. © 1995 John Wiley & Sons, Inc.     

A benign initiating system for cationic polymerization of isobutyl vinyl ether: Silver salt/aryl(alkyl) halide/lewis base

Aryl(alkyl) halides and silver salts were studied as environmentally benign initiating systems for cationic polymerization of isobutyl vinyl ether (IBVE). The reactivity of the benzyl cations could be effectively controlled by using dimethyl sulfide (Me₂S) as an additive, which was shown to be an effective Lewis base (LB), and diethyl ether as a reaction solvent. Detailed study of various benzyl cations and the order of addition of the reagents revealed that the reaction was controlled by the electronic and steric features of aryl(alkyl) halides, LBs, and IBVE, and a plausible reaction mechanism was presented. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2050–2058     

Controlled synthesis of glycopolymers with pendant D-glucosamine residues by living cationic polymerization

D -glucosamine-containing glycopolymers with well-controlled structure were synthesized by living cationic polymerization. To this end, D -glucosamine-containing vinyl ether (VE) of the type [CH₂()CH(OCH₂CH₂OR)] was prepared, where R denotes a 3,4,6-tri-O-acetyl-2-deoxy-2-phthalimide-β-D -glucopyranoside, i.e., the hydroxyl and amino groups in D -glucosamine residues are protected by acetyl and phthaloyl groups, respectively. It was found that (1) the efficient living cationic polymerization of VE monomer is achieved by a combination of ethylaluminum dichloride (EtAlCl₂) with an adduct of trifluoroacetic acid (TFA) and isobutyl VE (IBVE) [CH₃CH(OiBu)OCOCF₃] (i.e., TFA/EtAlCl₂ initiating system); and (2) the polymerization in toluene at the elevated temperature (0°C) is most suitable to proceed the homogeneous polymerization over the whole conversion range. The molecular weight distribution of the resulting polymers was very narrow ($ {\bar M}_w/{\bar M}_n \sim 1.1 $). Quantitative deprotection of the resulting precursor polymers was successfully achieved with hydrazine monohydrate to afford the corresponding water-soluble polymers with pendant D -glucosamine residues. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 751–757, 1997     

Living cationic polymerization of vinyl ethers with carboxylic acid/tin tetrahalide initiating systems. I. New initiating systems based on acetic acid and selection of Lewis acid and basic additive leading to living polymers with low polydispersity

Cationic polymerization of isobutyl vinyl ether (IBVE) with acetic acid (CH₃COOH)/tin tetrahalide (SnX₄: X = Cl, Br, I) initiating systems in toluene solvent at 0°C was investigated, and the reaction conditions for living polymerization of IBVE with the new initiating systems were established. Among these tin tetrahalides, SnBr₄ was found to be the most suitable Lewis acid to obtain living poly(IBVE) with a narrow molecular weight distribution (MWD). The polymerization with the CH₃COOH/SnBr₄ system, however, was accompanied with the formation of a small amount of another polymer fraction of very broad MWD, probably due to the occurrence of an uncontrolled initiation by SnBr₄ coupled with protonic impurity. Addition of 1,4-dioxane (1–1.25 vol %) or 2,6-di-tert-butylpyridine (0.1–0.6mM) to the polymerization mixture completely eliminated the uncontrolled polymer to give only the living polymer with very narrow MWD (M _w/M _n ≤ 1.1; M _w, weight-average molecular weight; M _n, number-average molecular weight). The M _n of the polymers increased in direct proportion to monomer conversion, continued to increase upon sequential addition of a fresh monomer feed, and was in good agreement with the calculated values assuming that one CH₃COOH molecule formed one polymer chain. Along with these results, kinetic study and direct ¹H-NMR observation of the living polymerization indicated that CH₃COOH and SnBr₄ act as so-called “initiator” and “activator”, respectively, and the living polymerization proceeds via an activation of the acetate dormant species. The basic additives such as 1,4-dioxane and 2,6-di-tert-butylpyridine would serve mainly as a “suppressor” of the uncontrolled initiation by SnBr₄. The polymers produced after quenching the living polymerization with methanol possessed the acetate dormant terminal and they induced living polymerization of IBVE in conjunction with SnBr₄ in the presence of 1,4-dioxane. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3173–3185, 1998     

Selectively degradable alternating copolymers of isobutyl vinyl ether and plant‐derived aldehydes with acyclic side chains: Effects of side group structures on copolymerization behaviors

Side group structures of aldehydes were demonstrated to have decisive effects on cationic copolymerizations with alkyl vinyl ether (VE). Alternating copolymerizations of isobutyl VE (IBVE) and plant‐derived aldehydes with acyclic side chains such as trans‐2,cis‐6‐nonadienal, trans‐2‐nonenal, and citral proceeded under appropriate reaction conditions with the EtSO₃H/GaCl₃ initiating system. In addition, some aldehydes copolymerized in a well‐controlled fashion to yield alternating copolymers with controlled molecular weights and narrow molecular weight distributions. Quantitative and selective acid hydrolysis of the resulting alternating copolymers, based on the acetal structures in the main chains, was also achieved to give other conjugated aldehydes as nearly sole degradation products. Copolymerization results of IBVE and various plant‐derived aldehydes with acyclic or cyclic side groups suggested that electron‐donating ability and bulkiness of the side groups were most likely responsible for the alternating and/or controlled copolymerization behaviors. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4684–4693     

Thermoresponsive NIPAM block copolymers containing densely grafted poly(vinyl ether) brushes synthesized by a combination of living cationic polymerization and RAFT polymerization

Diblock copolymers consisting of a multibranched polymethacrylate segment with densely grafted poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] pendants and a poly(N‐isopropylacrylamide) segment were synthesized by a combination of living cationic polymerization and RAFT polymerization. A macromonomer having both a poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] backbone and a terminal methacryloyl group was synthesized by living cationic polymerization. The sequential RAFT copolymerizations of the macromonomer and N‐isopropylacrylamide in this order were performed in aqueous media employing 4‐cyanopentanoic acid dithiobenzoate as a chain transfer agent and 4,4′‐azobis(4‐cyanopentanoic acid) as an initiator. The obtained diblock copolymers possessed relatively narrow molecular weight distributions and controlled molecular weights. The thermoresponsive properties of these polymers were investigated. Upon heating, the aqueous solutions of the diblock copolymers exhibited two‐stage thermoresponsive properties denoted by the appearance of two cloud points, indicating that the densely grafted poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] pendants and the poly(N‐isopropylacrylamide) segments independently responded to temperature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008