Suppressing the environmental dependence of the open‐circuit voltage in inverted polymer solar cells through a radical polymer anodic modifier

Developing stable, readily‐synthesized, and solution‐processable transparent conducting polymers for interfacial modifying layers in organic photovoltaic (OPV) devices has become of great importance. Here, the radical polymer, poly(2,2,6,6‐tetramethylpiperidinyloxy methacrylate (PTMA), is shown to not affect the absorption of the well‐studied poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) active layer when incorporated into inverted OPV devices, as it is highly transparent in the visible spectrum due to the non‐conjugated nature of the PTMA backbone. The inclusion of this radical polymer as an anode‐modifying layer enhanced the open‐circuit voltage and short‐circuit current density values over devices that did not contain an anodic modifier. Importantly, devices fabricated with the PTMA interlayer had performance metrics that were time‐independent over the entire course of multiples days of testing after exposing the OPV devices to ambient conditions. Furthermore, these high performance values were independent of the metal used as the top electrode contact in the inverted OPV devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 311–316     

Synthesis and morphology of all‐conjugated donor–acceptor block copolymers based on poly(3‐hexylthiophene) and poly(naphthalene diimide)

A series of all‐conjugated diblock and triblock copolymers comprised of poly(naphthalene diimide) (PNDI)‐based n‐type and the poly(3‐hexylthiophene) (P3HT) segments could be synthesized via the Kumada catalyst‐transfer polycondensation process. The crystalline structures and chain orientation of the block copolymer thin films were systematically studied by grazing incident wide‐angle X‐ray scattering (GIWAXS). The GIWAXS results indicated that both the P3HT and PNDI segments in the block copolymers form exclusive crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domain aligns with a face‐on rich orientation. In contrast, the blend films of the P3HT and PNDI homopolymers also show two distinguished crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domains align in different ways depending on the chemical structure of n‐type polymers, that is, PNDI1Th is isotropically dispersed, while PNDI2Th aligns with a face‐on rich orientation. In addition, the effect of thermal annealing on the crystalline behavior of the block copolymers is reported. The GIWAXS results indicated that thermal annealing increases the crystallinity of both segments without affecting their chain orientation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1139–1148     

Conjugated polymer with rigid donor poly(para‐divinylphenylamino) backbone and pendant cyanoacetic acid acceptor for dye sensitized solar cells

A donor backbone [poly(para‐divinylphenylamino)]‐acceptor (cyanoacetic acid side group) type conjugated polymer ( P2 ) has been synthesized and used as the active material for dye‐sensitized solar cells. DFT calculation shows that the insertion of vinyl link in the polymer backbone leads to a planar structure in P2 and changes the excited state significantly. Photoelectrochemical cells based on the DSSC format were fabricated using the polymers as sensitizers. The cell constructed using P2 exhibits a considerably high peak IPCE and J‐V response, with an overall power conversion efficiency of 3.67%. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2958–2965     

Exploring the synthesis and impact of end‐functional poly(3‐hexylthiophene)

In recent years, end‐functional poly(3‐hexylthiophene) (P3HT) has proven to be instrumental in the continued development and innovation within the broad conjugated polymer arena, enabling a variety of applications, particularly in organic electronics. The availability of P3HT with controlled molecular weights, low polydispersity, and importantly, a wide range of reactive end‐groups not only serves as a key building block for the preparation of conjugated block copolymers but also facilitates the development of hybrid nanocomposite materials via inorganic surface modification strategies. This Highlight focuses on the synthetic approaches to end‐functional P3HT and the impact of these systems in emerging technologies. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 831–841     

Confocal microscopy studies of shear‐induced coalescence in blends of poly(butyl methacrylate) and poly(2‐ethylhexyl methacrylate)

This article reports the results of confocal fluorescence microscopy studies of shear‐induced coalescence in binary blends of poly(2‐ethylhexyl methacrylate) (PEHMA; 90 wt %) and poly(butyl methacrylate) (PBMA; 10 wt %). We prepared the blends by casting a mixture of latex dispersions of the components onto a substrate and allowing the film to dry under ambient conditions. The initial morphology of the film was a dispersion of 120‐nm PBMA spheres in a continuous PEHMA matrix. One‐fifth of the PBMA particles were labeled with anthracene, the emission of which we observed with confocal microscopy. The blends were sheared in a parallel‐plate rheometer at 80 and 100 °C for 1 and 10 h. Careful image analysis allowed us to estimate the mean size of the dispersed phase and the width of the size distribution. The results were compared with the theoretical limits of Wu and Taylor. After 10 h of shearing, the mean particle size decreased and the particle distribution became narrower in comparison with the results obtained after 1 h of shearing. We explain this result by inferring that before the sample reached steady‐state morphology, its rate of coalescence was greater than the rate of particle breakup. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2317–2332, 2001     

A facile approach to fabricate hierarchically structured poly(3‐hexylthiophene‐2,5‐diyl) films

Microstructured surfaces have great potentials to improve the performances and efficiency of optoelectronic devices. In this work, a simple robust approach based on surface instabilities was presented to fabricate poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) films with ridge‐like/wrinkled composite microstructures. Namely, the hierarchically patterned films were prepared by spin coating the P3HT/tetrahydrofuran (THF) solution on a polydimethylsiloxane (PDMS) substrate to form stable ridge‐like structures, followed by solvent vapor swelling to create surface wrinkles with the orientation guided by the ridge‐like structures. During spin coating of the P3HT/THF solution, the ridge‐like structures were generated by the in‐situ template of the THF swelling‐induced creasing structures on the PDMS substrate. To our knowledge, it is the first report that the creasing structures are used as a recoverable template for patterning films. The crease‐templated ridge‐like structures were well modulated by the THF swelling time, the modulus of the PDMS substrate, the P3HT/THF solution concentration and the selective/blanket exposure of the PDMS substrate to O₂ plasma. UV–vis and fluorescence spectrometry measurements indicated that the light absorption and fluorescent emission were improved on the hierarchically patterned P3HT films, which can be utilized to enhance the efficiencies of organic solar cells. Furthermore, this simple versatile method based on the solvent swelling‐induced crease as the in‐situ recoverable template has been extended to pattern other spin‐coated films with different compositions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 928–939     

Nonisothermal crystallization kinetics of poly(ε‐caprolactone) blocks in double crystalline triblock copolymers containing poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) and poly(ε‐caprolactone) units

The poly(3‐hydroxbutyrate‐co‐3‐hydroxyvalerate)/poly(ε‐caprolactone) block copolymers (PHCLs) with three different weight ratios of PCL blocks (38%, named PHCL‐38; 53%, named PHCL‐53; and 60%, named PHCL‐60) were synthesized by using PHBV with two hydroxyl end groups to initiate ring‐opening polymerization of ε‐caprolactone. During DSC cooling process, melt crystallization of PHCL‐53 at relatively high cooling rates (9, 12, and 15 °C min^?1) and PHCL‐60 at all the selected cooling rates corresponded to PCL blocks so that PHCL‐53 and PHCL‐60 were used to study the nonisothermal crystallization behaviors of PCL blocks. The kinetics of PCL blocks in PHCL‐53 and PHCL‐60 under nonisothermal crystallization conditions were analyzed by Mo equation. Mo equation was successful in describing the nonisothermal crystallization kinetics of PCL blocks in PHCLs. Crystallization activation energy were estimated using Kissinger's method. The results of kinetic parameters showed that both blocks crystallized more difficultly than corresponding homopolymers. With the increase of PCL content, the crystallization rate of PCL block increased gradually. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Low band‐gap modulation of isoindigo‐based copolymers toward high open‐circuit voltage of polymer solar cells

Designing low band‐gap‐conjugated polymers coupled with low HOMO levels attracts great attention in the field of polymer solar cells (PSCs). By using donor–acceptor (D‐A) copolymerization strategy, we designed and synthesized a series of low band‐gap copolymers with deep HOMO levels via introducing an isoindigo (IID) acceptor unit in the copolymers with the donor unit of fluorene (F) (PIID‐F), carbazole (Cz) (PIID‐Cz), thiophene (Th) (PIID‐Th), dithiophene (DTh) (PIID‐DTh), or dithienosilole (DTS) (PIID‐DTS). The HOMO level of the copolymers, measured by electrochemical cyclic voltammetry, varies from ?5.3 eV to ?5.8 eV, depending on different donor units in the copolymers. However, the LUMO levels of all the copolymers are fixed at about ?3.6 eV, which is mainly determined by IID acceptor unit due to its strong electron‐withdrawing ability. The new results will provide an effect help in designing IID based molecular structures. Among the copolymers, PIID‐DTS has a low band gap of 1.58 eV and possesses a low‐lying HOMO energy level of ?5.33 eV. The PSCs based on PIID‐DTS as donor and PC₇₀BM as acceptor exhibited a high open‐circuit voltage (V_oc) of 0.93 V and a primary power conversion efficiency of 2.45%. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3477–3485     

Light‐emitting copolymers based on fluorene and selenophene—Comparative studies with its sulfur analogue: Poly(fluorene‐co‐thiophene)

A series of soluble conjugated copolymers derived from 9,9‐dioctylfluorene (FO) and selenophene (SeH) was synthesized by a palladium‐catalyzed Suzuki coupling reaction with various feed ratios of SeH to FO less than or equal to 50%. The efficient energy transfer from fluorene segments to narrow band‐gap selenophene sites was observed. In comparison with the very well studied copolymer poly(fluorene‐co‐thiophene), poly(9,9‐dioctylfluorene‐co‐selenophene) (PFO‐SeH) shows redshifted photoluminescence (PL) and electroluminescence (EL) emission. PL spectra of the PFO‐SeH copolymers show a significant redshift along with increasing selenophene content in the copolymers and also with increasing polymer concentration in solution. PL quantum efficiency of the selenophene‐containing PFO copolymer is much lower than that of corresponding PFO‐thiophene (Th) copolymers. All these features of PFO‐SeH copolymers can be explained by the difference in aromaticity of selenophene and thiophene heterocycles and the heavy atom effect of Se in comparison with S‐atoms. The device fabricated with PFO‐SeH15 as the emissive layer exhibited high external quantum efficiency (0.51%) at a luminance of 1570 cd/m². Device performance is limited by electron injection and the strong quenching effect of Se atoms. Devices with PFO‐SeH copolymers blended into PFO homopolymers show significant improvement in device performance. External quantum efficiency as high as 1.7% can be obtained for PFO‐SeH30/PFO blend devices. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 823–836, 2005     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Synthesis and self‐assembly of diblock copolymers composed of poly(3‐hexylthiophene) and poly(fluorooctyl methacrylate) segments

Regioregular poly(3‐hexylthiophene)‐b‐poly(1H,1H‐dihydro perfluorooctyl methacrylate) (P3HT‐b‐PFOMA) diblock copolymers were synthesized by atom transfer radical polymerization of fluorooctyl methacrylate using bromoester terminated poly(3‐hexylthiophene) macroinitiators in order to investigate their morphological properties. The P3HT macroinitiator was previously prepared by chemical modification of hydroxy terminated P3HT. The block copolymers were well characterized by ¹H NMR spectroscopy and gel permeation chromatography. Transmission electron microscopy was used to investigate the nanostructured morphology of the diblock copolymers. The block copolymers are able to undergo microphase separation and self‐assemble into well‐defined and organized nanofibrillar‐like micellar morphology. The development of the morphology of P3HT‐b‐PFOMA block copolymers was investigated after annealing in solvent vapor and also in supercritical CO₂. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis,reactivity, and optoelectronic properties of poly(3‐alkenylthiophene) diblock copolymers

Poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene) and poly(3‐hexylthiophene)‐b‐poly(3‐undecenylthiophene) diblock copolymers have been synthesized by McCullough method. X‐ray diffraction analysis of the diblock copolymers displayed all the reflection peaks specific to regioregular poly(3‐hexylthiophene), indicating that the presence of poly(3‐alkenylthiophene) block does not affect the packing of the polymer in the solid state. The synthesized diblock copolymers were subjected to hydroboration/oxidation and hydrosilation to demonstrate the reactivity of the alkenyl substituents. Furthermore, poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene) was used as a chain transfer agent for the ruthenium‐catalyzed ring‐opening metathesis polymerization of cyclooctene to generate a polycyclooctene graft copolymer, which was hydrogenated to give poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene‐g‐polyethylene). The opto‐electronic properties and the morphology of the synthesized polymers have been investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Phase Behavior and Thermal Properties for Binary Blends of Bacterial Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s with Narrow‐Comonomer‐Unit Compositional Distribution

The miscibility and the effect of compositional distribution on physical properties were investigated for binary blends of biosynthesized poly(3‐hydroxybutyrate) [P(3HB)] and comonomer compositionally fractionated poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s [P(3HB‐co‐3HH)] with narrow compositional distribution. Biosynthesized P(3HB‐co‐3HH) samples were compositionally fractionated using solvent (chloroform)/nonsolvent (n‐heptane) mixtures. The binary blends of fractionated P(3HB‐co‐3HH)s with different 3HH unit content were prepared by casting from solution in chloroform. The miscibility and the thermal properties of these blends were analyzed by differential scanning calorimetry (DSC). It was found that the two components are miscible in the amorphous phase when the difference in 3HH unit content between the two component polymers of these blends is less than 20 mol‐%, subsequently they are immiscible when the difference is larger than 30 mol‐%. By comparing the thermal properties of the binary blends of fractions, with those for the fractions themselves, and with those for the bacterially as‐produced unfractionated copolyesters, the effects of compositional distribution on the properties of copolyesters were discussed.

Glass transition temperatures of blends PHB/H10, H10/H20, and PHB/H20 versus total 3HH unit content in the blends. The solid lines are the best fits of the experimental results of the P(3HB‐co‐3HH) fractions with narrow compositional distribution.     

Poly(3‐hexylthiophene) aggregation at solvent–solvent interfaces

The aggregation behavior of P3HT is investigated at the interface of orthogonal solvents for P3HT. The changeable characteristics of P3HT aggregate dispersions, for example, extent of aggregation and intrachain order, are studied by varying (1) the interfacial area, (2) the poor solvent used to induce aggregation – dichloromethane (DCM), hexane (HEX), and acetonitrile (AcN) – and (3) the relative composition of the good solvent, chloroform (CF), and poor solvents. The results are compared to those observed using rapid injection of the solvent. Miscibility gap values (Δδ) provide a reasonable justification of the assembly behavior of P3HT in the solvent mixtures in terms of the kinetics of polymer aggregation and the kinetics of solvent mixing at the interface. Atomic force microscopy (AFM) is used to analyze the morphology of films processed from dispersions with disparate characteristics, but having the same solvent composition, for example, 70:30 CF:HEX or 60:40 CF:DCM. Based on the disparity of the kinetics and miscibility gap values, the prevalence of specific structural motifs in the films, for example, spheroids (globules) and fibers, is effectively rationalized in terms of the structural attributes of the aggregates in the liquid phase rather than the evaporation rate (boiling point) differences of the solvents in the mixture. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 999–1011     

Synthesis and properties of multiblock copolymers consisting of poly(L‐lactic acid) and poly(oxypropylene‐ co‐oxyethylene) prepared by direct polycondensation

A multiblock copoly(ester–ether) consisting of poly(l ‐lactic acid) (PLLA) and poly(oxypropylene‐co‐oxyethylene) (PN) was prepared and characterized. Preparation was done via the solution polycondensation of a thermal oligocondensate of l ‐lactic acid, a commercially available telechelic polyether (PN: Pluronic‐F68), and dodecanedioic acid as a carboxyl/hydroxyl adjusting agent. When stannous oxide was used as the catalyst, the molecular weight of the resultant PLLA/PN block copolymers became very high (even with a high PN content) under optimized reaction conditions. The refluxing of diphenyl ether (solvent) at reduced pressure allowed the efficient removal of the condensed water from the reaction system and the feed‐back of the intermediately formed l ‐lactide at the same time in order to successfully bring about a high degree of condensation. The copolymer films obtained by solution casting became more flexible with the increasing PN content as soft segments. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1513–1521, 1999