特征空间和符号相干系数融合的最小方差超声波束形成

为了提高医学超声成像的空间分辨率,提出一种融合了特征空间最小方差与符号相干系数的波束形成方法。首先利用最小方差法计算回波数据的协方差矩阵和加权向量;然后对协方差矩阵进行特征分解得到信号子空间,并将加权向量投影到该空间上;最后计算符号相干系数,用于优化特征空间法得到的回波信号,最终获得超声成像数据。为验证算法的有效性,对医学超声成像中常用的点目标、斑目标进行仿真,对点目标仿体和人体颈动脉组织进行超声成像实验。结果表明:所提出的方法在分辨率、对比度以及稳健性等方面都优于传统的延时叠加算法、最小方差算法、特征空间最小方差法以及特征空间与相干系数融合的方法。     

改进的最小方差算法在超声成像中的应用

为了提高最小方差超声成像算法的分辨率、对比度以及对噪声的鲁棒性,提出一种改进的最小方差成像算法。该方法首先基于回波信号中期望信号与噪声信号的可分离性将信号划分为期望信号和噪声信号,然后根据最小方差原理,求出加权向量使期望信号功率最小,同时,为了增加算法对噪声的鲁棒性,对信号方向向量增加一对约束条件,进一步提高图像质量。在全发全收和合成孔径模式下对点目标和吸声斑进行仿真,结果表明所提算法在全发全收模式下,-6 dB处分辨率在最小方差基础上提高了1倍左右,在合成孔径模式下,对比度在特征空间最小方差算法基础上提高了8 dB,且远优于传统延时叠加算法。最后通过实验进一步表明改进的最小方差算法图像在分辨率、对比度及对噪声的鲁棒性等方面表现更优,可以有效的改善超声图像的质量。      

特征空间和符号相干系数融合的最小方差超声波束形成

为了提高医学超声成像的空间分辨率,提出一种融合了特征空间最小方差与符号相干系数的波束形成方法。首先利用最小方差法计算回波数据的协方差矩阵和加权向量;然后对协方差矩阵进行特征分解得到信号子空间,并将加权向量投影到该空间上;最后计算符号相干系数,用于优化特征空间法得到的回波信号,最终获得超声成像数据。为验证算法的有效性,对医学超声成像中常用的点目标、斑目标进行仿真,对点目标仿体和人体颈动脉组织进行超声成像实验。结果表明:所提出的方法在分辨率、对比度以及稳健性等方面都优于传统的延时叠加算法、最小方差算法、特征空间最小方差法以及特征空间与相干系数融合的方法。      

信噪比后滤波与特征空间融合的最小方差超声成像算法

为了提高超声成像空间分辨率和对比度,提出了一种信噪比后滤波与特征空间融合的最小方差波束形成算法。首先,利用信号子空间划分将最小方差算法得到的权矢量投影到信号子空间中提高成像对比度,然后基于信号相干性设计滤波系数,并引入基于信噪比的噪声加权系数,最终得到融合信噪比后滤波与特征空间的最小方差算法。为验证本算法的有效性,使用FieldⅡ对点目标和吸声斑目标进行了仿真实验验证,并采用密歇根大学geabr_0实验数据进行成像。实验结果表明:所提算法在对比度和分辨率上均有所提高,明显优于传统延时叠加算法,最小方差算法和ESBMV_wiener算法,且对噪声具有较强鲁棒性。      

互相关自适应加权的医学超声成像算法研究

根据超声成像系统的超声回波信号互相关性,提出互相关自适应加权超声成像算法.该算法根据散射点回波信号之间的空间相关性设置加权系数,对不同位置的散射点进行自适应加权成像,从而降低了成像系统的旁瓣,抑制了相关性较差的噪声.通过Field II仿真的点目标和吸声斑目标处理结果表明该方法成像的横向和纵向分辨率高,成像速度快.相对于延时叠加(DAS)算法,该算法对散射点成像可提高对比度16 dB,对于吸声斑成像可提高对比度0.85 dB.最后采用完备数据集进行实验,结果表明该算法成像分辨率优于DAS算法,对比度提高了17 dB.     

特征空间最小方差波束形成与相关系数特征值加权相融合的超声成像算法

为了进一步提高超声成像的质量,提出一种信号特征空间的最小方差波束形成与相关系数特征值加权相融合的超声成像算法。利用超声回波信号具有一定的相关性,而相关系数空间最大特征值可以反映回波信号相关性较强的性质,将该特征值作为自适应加权系数对信号特征空间最小方差波束形成(EIBMV)的结果进行加权成像,得到高质量的成像结果。通过对散射点目标和斑目标的Field II仿真,结果表明该算法相对于EIBMV算法,亮斑对比度提高了4.22 dB,暗斑对比度提高了1.88 dB,并且进一步提高了横向分辨率。      

最小方差波束形成与广义相干系数融合的医学超声成像方法

为了在医学超声成像过程中提高分辨率并修正由生物组织的声速不均匀性引入的聚焦误差,提出了将最小波束形成与广义相干系数融合的高分辨率成像方法.首先对阵元数据进行延时聚焦处理,得到了聚焦后的多通道数据;然后对多通道数据进行最小方差波束形成,同时把阵元数据变换到波束域,计算广义相干系数;最后利用广义相干系数加权最小波束形成的结...     

子阵列差分系数加权的超声成像算法

传统的自适应加权系数可以有效改善超声图像的分辨率和对比度,但会影响背景图像的散斑特性,因此提出子阵列差分加权系数(SDF)以提升图像质量.该系数适用于传统线扫描超声成像,首先对阵列接收到的回波信号采用子阵列平滑的方式计算均值,得到信号中高相干性成份的强度,再用差分的方式反映相邻阵元回波信号之间的差异性,最后对延时叠加(...     

超声虚源成像中自适应双向空间逐点聚焦方法

针对传统超声成像中图像分辨率和对比度随深度下降的问题,提出了一种基于虚源的自适应双向空间逐点聚焦超声成像方法。首先,使用超声换能器线列阵分子孔径分别定焦点发射和接收超声波,采集扫描线数据;然后将焦点视为虚拟点声源,计算虚源到空间成像点的延时,利用合成孔径原理再次进行空间逐点聚焦;在合成过程中采用相干系数进行自适应加权。采用空间脉冲响应法对不同深度的点目标和囊目标仿真成像,从而量化分辨率和对比度。在F数为1.5、焦距为10 mm时(对应子孔径阵元数为17)可以获得与64通道定焦点发射、动态聚焦接收相当的图像质量且在所有深度上保持一致。实际硬件平台的体模成像实验进一步验证了方法的有效性。该方法可在整个成像深度范围内保持和常规成像一致的分辨率和对比度,从而获得更优的整体成像效果。      

利用回波相干性的医学超声成像相位畸变校正方法

为了提高相位畸变条件下的医学超声成像的横向分辨率和对比度,提出了一种利用回波信号相干性的校正方法。首先给出平均相干系数的概念,并将其作为相位误差校正的度量,然后通过最大化平均相干系数逐步校正各个通道的延时误差,最后再利用经过校正的数据计算出一组新的相干系数并对回波信号进行加权优化,从而得到最终用于成像的数据。对点散射目标及斑散射目标的仿真结果分别显示,利用所提出的方法横向分辨率提高了约0.24 mm,对比度提高了约18 dB,且要优于邻近阵元互相关方法和相干系数直接加权的处理方法。利用回波相干性的相位畸变校正方法结合了相位误差校正和加权处理的优点,可以有效地改善医学超声成像的质量。      

Eigenspace-based minimum variance beamformer combined with Wiener postfilter for medical ultrasound imaging

In this paper, a new beamformer which combines the eigenspace-based minimum variance (ESBMV) beamformer with the Wiener postfilter is proposed for medical ultrasound imaging. The primary goal of this work is to further improve the medical ultrasound imaging quality on the basis of the ESBMV beamformer. In this method, we optimize the ESBMV weights with a Wiener postfilter. With the optimization of the Wiener postfilter, the output power of the new beamformer becomes closer to the actual signal power at the imaging point than the ESBMV beamformer. Different from the ordinary Wiener postfilter, the output signal and noise power needed in calculating the Wiener postfilter are estimated respectively by the orthogonal signal subspace and noise subspace constructed from the eigenstructure of the sample covariance matrix.We demonstrate the performance of the new beamformer when resolving point scatterers and cyst phantom using both simulated data and experimental data and compare it with the delay-and-sum (DAS), the minimum variance (MV) and the ESBMV beamformer. We use the full width at half maximum (FWHM) and the peak-side-lobe level (PSL) to quantify the performance of imaging resolution and the contrast ratio (CR) to quantify the performance of imaging contrast. The FWHM of the new beamformer is only 15%, 50% and 50% of those of the DAS, MV and ESBMV beamformer, while the PSL is 127.2 dB, 115 dB and 60 dB lower. What is more, an improvement of 239.8%, 232.5% and 32.9% in CR using simulated data and an improvement of 814%, 1410.7% and 86.7% in CR using experimental data are achieved compared to the DAS, MV and ESBMV beamformer respectively. In addition, the effect of the sound speed error is investigated by artificially overestimating the speed used in calculating the propagation delay and the results show that the new beamformer provides better robustness against the sound speed errors. Therefore, the proposed beamformer offers a better performance than the DAS, MV and ESBMV beamformer, showing its potential in medical ultrasound imaging.     

Broadband optimal contrast resolution beamforming

This paper proposes a novel receive beamformer architecture for broadband imaging systems that uses unique finite impulse response (FIR) filters on each channel. The conventional delay-and-sum (DAS) beamformer applies receive apodization by weighting the signal on each receive channel prior to beam summation. Our proposed FIR beamformer passes the focused receive radio frequency (RF) signals through multi-tap FIR filters on each receive channel prior to summation. The receive FIR filters are constructed to maximize the contrast resolution of the system’s spatial response. The broadband FIR beamformer produces spatial point spread functions (PSFs) with narrower mainlobe widths and lower sidelobe levels than spatial PSFs produced by the conventional DAS beamformer.We present simulation results showing that FIR filters of modest tap lengths (3-7) can yield marked improvement in image contrast and point resolution. Specifically we show that 7-tap FIR filters can reduce sidelobe and grating lobe energy by 30 dB and improve contrast resolution by as much as 20 dB compared to conventional apodization profiles. This improvement in contrast resolution comes at the expense of a decrease in beamformer sensitivity. We investigate the effects of phase aberration and show in simulation results that the multi-tap FIR beamformer outperforms the unaberrated DAS beamformer by 8-12 dB even in the presence of moderate aberration characterized by a root-mean-square strength of 28 ns and a full-width at half-maximum correlation length of 3.6 mm. We show experimental results wherein multi-tap FIR filters decrease sidelobe energy in the resulting 2D spatial response while achieving a narrow mainlobe. We also show results where the FIR beamformer improves the contrast to noise ratio (CNR) in simulated B-mode cyst images by more than 4 dB. Our algorithm has the potential to significantly improve ultrasound beamforming in any application where the system response is reasonably well characterized. Furthermore, this algorithm can be used to increase contrast and resolution in one-way beamforming systems such as acousto-optic and opto-acoustic imaging.     

超声成像中基于特征空间的前后向最小方差波束形成

针对最小方差(MV)波束形成在算法稳健性和超声成像对比度方面存在的缺点,提出一种将特征空间法和前后向空间平滑法融合用于最小方差波束形成的超声成像方法。首先用前后向空间平滑取代传统的前向空间平滑,得到更精确的协方差矩阵;然后计算最优加权向量,并将该向量投影到由协方差矩阵特征空间构造的信号子空间中;最后利用投影所获得的向量与阵元数据进行运算得到成像回波数据。为了验证算法的有效性,对医学成像中常用的点目标和斑目标进行了成像实验。仿真结果表明:所提出的方法不依赖于对角加载参数的选取,在保持MV算法高分辨率的同时,还有效提高图像的对比度和算法的稳健性。      

Generalized sidelobe canceler beamforming applied to medical ultrasound imaging

A generalized sidelobe canceler (GSC) approach is proposed for medical ultrasound imaging. The approach uses a set of adaptive weights instead of traditional non-adaptive weights, thus suppressing the interference and noise signal of echo data. In order to verify the validity of the proposed approach, Field II is applied to obtain the echo data of synthetic aperture (SA) for 13 scattering points and circular cysts. The performance of GSC is compared with SA using boxcar weights and Hamming weights, and is quantified by the full width at half maximum (FWHM) and peak signal-to-noise ratio (PSNR). Imaging of scattering point utilizing SA, SA (hamming), GSC provides FWHMs of 1.13411, 1.68910, 0.36195 mm and PSNRs of 60.65, 57.51, 66.72 dB, respectively. The simulation results of circular cyst also show that GSC can perform better lateral resolution than non-adaptive beamformers. Finally, an experiment is conducted on the basis of actual echo data of an ultrasound system, the imaging result after SA, SA (hamming), GSC provides PWHMs of 2.55778, 3.66776, 1.01346 mm at z = 75.6 mm, and 2.65430, 3.76428, 1.27889 mm at z = 77.3 mm, respectively.