硅衬底GaN基LED N极性n型欧姆接触研究

在Si衬底GaN基垂直结构LED的N极性n型面上,利用电子束蒸发的方法制作了Ti/Al电极,通过了I-V曲线研究了有无AlN缓冲层对这种芯片欧姆接触的影响.结果显示,去除AlN缓冲层后的N极性n型面与Ti/Al电极在500到600 ℃范围内退火才能形成欧姆接触.而保留AlN缓冲层的N极性n型面与Ti/Al电极未退火时就表现为较好的欧姆接触,比接触电阻率为2×10^-5 Ω·cm²,即使退火温度升高至600 ℃,也始终保持着欧姆接触特性.因此,AlN缓冲层的存在是Si衬底GaN基垂直结构LED获得高热稳定性n型欧姆接触的关键. 关键词： 硅衬底 N极性 AlN缓冲层 欧姆接触     

不同退火方式对Ni/SiC接触界面性质的影响

采用快速热退火(rapid thermal annealing, RTA)法和脉冲激光辐照退火(laser spark annealing, LSA)法, 在n型4H-SiC的Si面制备出Ni电极欧姆接触. 经传输线法测得RTA样品与LSA样品的比接触电阻分别为5.2×10^-4 Ω·cm², 1.8× 10^-4 Ω·cm². 使用扫描电子显微镜、原子力显微镜、透射电子显微镜、拉曼光谱等表征手段, 比较了两种退火方式对电极表面形貌、电极/衬底截面形貌和元素成分分布、SiC衬底近表层碳团簇微结构的影响. 结果表明, 相比于RTA, LSA法制备出的欧姆接触在电极表面形貌、界面形貌、电极层组分均匀性等方面都具有明显优势, 有望使LSA成为一种非常有潜力的制备欧姆接触的退火处理方法.     

退火温度和退火气氛对Ni/Au与p-GaN之间欧姆接触性能的影响

研究了不同退火温度和气氛对Ni/Au与p-GaN之间欧姆接触性能的影响. 采用圆形传输线模型方法得到不同退火温度和不同退火气氛下的比接触电阻率. 结果表明, 较适宜的退火温度为500 ℃左右, 退火温度太高或太低都会导致比接触电阻率的增大; 较适宜的退火气氛为适量含氧的氮气气氛, 且氧气含量对比接触电阻率大小的影响并不显著. 经过对退火条件的优化, 得到的比接触电阻率可达7.65×10^-4 Ω·cm². 关键词： p-GaN 欧姆接触 圆形传输线模型 快速热退火     

低接触电阻率Ni/Ag/Ti/Au反射镜电极的研究

研究了Ag的厚度、退火时间、沉积温度对于Ni/Ag/Ti/Au电极的反射率及与p-GaN欧姆接触性能的影响. 利用分光光度计测量反射率, 采用圆形传输线模型计算比接触电阻率. 结果表明: 随着Ag厚度的增加, Ni/Ag/Ti/Au电极的反射率逐渐增大; 在氧气氛围中, 随着退火时间从1 min增至10 min, 300 ℃退火时, 比接触电阻率持续下降, 而对于400-600 ℃退火, 比接触电阻率先减小后增大; 在300和400 ℃氧气中进行1-10 min 的退火后, Ni/Ag/Ti/Au的反射率变化较小, 退火温度高于400 ℃时, 随着退火时间的增加, 反射率急剧下降; 在400 ℃氧气中3 min退火后, 比接触电阻率可以达到3.6×10^-3 Ω·cm². 此外, 适当提高沉积温度可以增加Ni/Ag/Ti/Au的反射率并降低比接触电阻率, 沉积温度为120 ℃条件下的Ni/Ag/Ti/Au电极在450 nm处反射率达到90.1%, 比接触电阻率为6.4×10^-3 Ω·cm². 综合考虑电学和光学性能, 在沉积温度为120 ℃下蒸镀Ni/Ag/Ti/Au (1/200/100/100 nm)并在400 ℃氧气中进行3 min退火可以得到较优化的电极. 利用此电极制作的垂直结构发光二极管在350 mA电流下的工作电压为2.95 V, 输出光功率为387.1 mW, 电光转换效率达到37.5%.     

TiAl3 和Ti/TiAl3 非合金化电极n型GaN欧姆接触的实现

在不进行合金化的情况下,首次直接采用TiAl3合金材料作为金属接触电极.在蓝宝石衬底上生长的n型载流子浓度为2×1018 cm-3的GaN上,成功地得到低接触电阻的欧姆接触,并由环形传输线模型方法测得比接触电阻率为3×10-5 Ω*cm2.与通常n型欧姆接触采用的Ti/Al双层结构比较,TiAl3合金结构更容易形成非合金化的n型欧姆接触.在此实验基础上,进一步分析了N空位和界面层处的TiAl3在形成非合金化或低温退火欧姆接触中发挥的作用,由此设计的Ti/TiAl3/Ni/Au接触结构,在TiAl3合金结构基础上明显地降低了接触电阻率.     

传输线模型测量Au/Ti/p型金刚石薄膜的欧姆接触电阻率

采用传输线模型测量了重B掺杂p型金刚石薄膜(约10²⁰cm^-3)上Ti/A u欧姆接触电阻率ρ_c,测试了500℃退火前后及大电流情况下的I-V特性,研究 了退火对ρ_c的影响.结果表明,重掺杂和退火工艺是改善欧姆接触的有效手段. ρ_c随测试温度的变化表明金属/半导体接触界面载流子输运机制为隧道穿透.而 光照对ρ_c影响的分析表明金刚石可作为理想窗口材料.测试得到的最低ρ _c值约为10^-4Ωcm². 关键词： 金刚石薄膜 欧姆接触 接触电阻率     

热退火处理对AuGeNi/n-AlGaInP欧姆接触性能的影响

本文在n-(Al0.27Ga0.73)0.5In0.5P表面通过电子束蒸发Ni/Au/Ge/Ni/Au叠层金属并优化退火工艺成功制备了具有较低接触电阻的欧姆接触,其比接触电阻率在445℃退火600 s时达到1.4×10–4 W·cm2.二次离子质谱仪测试表明,叠层金属Ni/Au/Ge/Ni/Au与n-AlGaInP界面发生固相反应,Ga,In原子由于热分解发生外扩散并在晶格中留下Ⅲ族空位.本文把欧姆接触形成的原因归结为Ge原子内扩散占据Ga空位和In空位作为施主提高N型掺杂浓度.优化退火工艺对低掺杂浓度n-(Al0.27Ga0.73)0.5In0.5P的欧姆接触性能有显著改善效果,但随着n-(Al0.27Ga0.73)0.5In0.5P掺杂浓度提高,比接触电阻率与退火工艺没有明显关系.本文为n面出光的AlGaInP薄膜发光二极管芯片的n电极制备提供了一种新的方法,有望大幅简化制备工艺,降低制造成本.     

电离辐射对部分耗尽绝缘体上硅器件低频噪声特性的影响

本文针对辐射前后部分耗尽结构绝缘体上硅(SOI)器件的电学特性与低频噪声特性开展试验研究. 受辐射诱生埋氧化层固定电荷与界面态的影响, 当辐射总剂量达到1 M rad(Si) (1 rad = 10^-2 Gy)条件下, SOI器件背栅阈值电压从44.72 V 减小至12.88 V、表面电子有效迁移率从473.7 cm²/V·s降低至419.8 cm²/V· s、亚阈斜率从2.47 V/dec增加至3.93 V/dec; 基于辐射前后亚阈斜率及阈值电压的变化, 可提取得到辐射诱生界面态与氧化层固定电荷密度分别为5.33×10¹¹ cm^{- 2}与2.36×10¹² cm^-2. 受辐射在埋氧化层-硅界面处诱生边界陷阱、氧化层固定电荷与界面态的影响, 辐射后埋氧化层-硅界面处电子被陷阱俘获/释放的行为加剧, 造成SOI 器件背栅平带电压噪声功率谱密度由7×10^{- 10} V²·Hz^-1增加至1.8×10^-9 V² ·Hz^-1; 基于载流子数随机涨落模型可提取得到辐射前后SOI器件埋氧化层界面附近缺陷态密度之和约为1.42×10¹⁷ cm^-3·eV^-1和3.66×10¹⁷ cm^-3·eV^-1. 考虑隧穿削弱因子、隧穿距离与时间常数之间关系, 本文计算得到辐射前后埋氧化层内陷阱电荷密度随空间分布的变化.     

基于两步退火法提升Al/n~+Ge欧姆接触及Ge n~+/p结二极管性能

锗(Ge)中高激活浓度、低扩散深度的n型掺杂是实现高性能Ge n-MOSFET的重要前提条件.本文采用低温预退火与脉冲激光退火相结合的两步退火法,结合磷离子注入,制备Al/n~+Ge的欧姆接触以及Ge n~+/p结二极管.通过电流-电压特性测试来研究Al/n~+Ge的欧姆接触以及Ge n~+/p结二极管的性能,测试结果表明:低温预退火可初步修复注入损伤,并降低激光退火时杂质的扩散深度;结合离子注入工艺和两步退火工艺,Al/n~+Ge欧姆接触的比接触电阻率降至2.61×10~(-6)Ω·cm~2,Ge n~+/p结二极管在±1V的整流比提高到8.35×10~6,欧姆接触及二极管性能均得到了显著提升.     

铜-钼源漏电极对非晶氧化铟镓锌薄膜晶体管性能的改善

在铜(Cu)和非晶铟镓锌氧化物(a-IGZO)之间插入30 nm厚的钼(Mo)接触层, 制备了具有Cu-Mo源漏电极的a-IGZO薄膜晶体管(TFT). Mo接触层不仅能够抑制Cu与a-IGZO有源层之间的扩散, 而且提高了Cu电极与玻璃基底以及栅极绝缘层的结合强度. 制备的Cu-Mo结构TFT与纯Cu 结构TFT相比, 具有较高的迁移率(～9.26 cm²·V^-1·s^-1)、更短的电流传输长度(～0.2 μm)、更低的接触电阻(～1072 Ω)和有效接触电阻率(～1×10^-4Ω·cm²), 能够满足TFT 阵列高导互联的要求.     

Low specific contact resistivity to graphene achieved by AuGe/Ni/Au and annealing process

Low metal-graphene contact resistance is important in making high-performance graphene devices.In this work,we demonstrate a lower specific contact resistivity of Au_(0.88)Ge_(0.12)/Ni/Au-graphene contact compared with Ti/Au and Ti/Pt/Au contacts.The rapid thermal annealing process was optimized to improve AuGe/Ni/Au contact resistance.Results reveal that both pre- and post-annealing processes are effective for reducing the contact resistance.The specific contact resistivity decreases from 2.5 × 10~(-4) to 7.8 × 10~(-5) Ω·cm~2 by pre-annealing at 300 ℃ for one hour,and continues to decrease to9.5 × 10~(-7) H·cm~2 after post-annealing at 490 ℃ for 60 seconds.These approaches provide reliable means of lowering contact resistance.     

高迁移率Ge沟道器件研究进展

高迁移率Ge沟道器件由于其较高而且更对称的载流子迁移率, 成为未来互补型金属-氧化物-半导体(CMOS) 器件极有潜力的候选材料. 然而, 对于Ge基MOS器件, 其栅、源漏方面面临的挑战严重影响了Ge基MOS 器件性能的提升, 尤其是Ge NMOS器件. 本文重点分析了Ge基器件在栅、源漏方面面临的问题, 综述了国内外研究者们提出的不同解决方案, 在此基础上提出了新的技术方案. 研究结果为Ge基MOS 器件性能的进一步提升奠定了基础.     

High-performance germanium n~+/p junction by nickel-induced dopant activation of implanted phosphorus at low temperature

High-performance Ge n~+/p junctions were fabricated at a low formation temperature from 325℃ to 400℃ with a metal(nickel)-induced dopant activation technique. The obtained Ni Ge electroded Ge n+/p junction has a rectification ratio of 5.6×10~4 and a forward current of 387 A/cm~2at -1 V bias. The Ni-based metal-induced dopant activation technique is expected to meet the requirement of the shallow junction of Ge MOSFET.     

Structure and luminescence of a-plane GaN on r-plane sapphire substrate modified by Si implantation

We show the structural and optical properties of non-polar a-plane GaN epitaxial films modified by Si ion implantation. Upon gradually raising Si fluences from 5×10¹³ cm^-2 to 5×10¹⁵ cm^-2, the n-type dopant concentration gradually increases from 4.6×10¹⁸ cm^-2 to 4.5×10²⁰ cm^-2, while the generated vacancy density accordingly raises from 3.7×10¹³ cm^-2 to 3.8×10¹⁵ cm^-2. Moreover, despite that the implantation enhances structural disorder, the epitaxial structure of the implanted region is still well preserved which is confirmed by Rutherford backscattering channeling spectrometry measurements. The monotonical uniaxial lattice expansion along the a direction (out-of-plane direction) is observed as a function of fluences till 1×10¹⁵ cm^-2, which ceases at the overdose of 5×10¹⁵ cm^-2 due to the partial amorphization in the surface region. Upon raising irradiation dose, a yellow emission in the as-grown sample is gradually quenched, probably due to the irradiation-induced generation of non-radiative recombination centers.     

Phosphorus diffusion and activation in fluorine co-implanted germanium after excimer laser annealing

The diffusion and the activation of phosphorus in phosphorus and fluorine co-implanted Ge after being annealed by excimer laser are investigated. The results prove that the fluorine element plays an important role in suppressing phosphorus diffusion and enhancing phosphorus activation. Moreover, the rapid thermal annealing process is utilized to evaluate and verify the role of fluorine element. During the initial annealing of co-implanted Ge, it is easier to form high bonding energy F_nV_m clusters which can stabilize the excess vacancies, resulting in the reduced vacancy-assisted diffusion of phosphorus. The maximum activation concentration of about 4.4×10²⁰ cm^-3 with a reduced diffusion length and dopant loss is achieved in co-implanted Ge that is annealed at a tailored laser fluence of 175 mJ/cm². The combination of excimer laser annealing and co-implantation technique provides a reference and guideline for high level n-type doping in Ge and is beneficial to its applications in the scaled Ge MOSFET technology and other devices.     

金属有机物化学气相沉积生长GaN薄膜的室温热电特性研究

采用金属有机物化学气相沉积技术生长了不同掺杂浓度的GaN薄膜, 并且通过霍尔效应测试和塞贝克效应测试, 表征了室温下GaN薄膜的载流子浓度、迁移率和塞贝克系数. 在实验测试的基础上, 计算了GaN薄膜的热电功率因子, 并且结合理论热导率确定了室温条件下GaN薄膜的热电优值(ZT). 研究结果表明: GaN薄膜的迁移率随着载流子浓度的增加而减小, 电导率随着载流子浓度的增加而增加; GaN 薄膜材料的塞贝克系数随载流子浓度的增加而降低, 其数量级在100–500 μV/K范围内; GaN薄膜材料在载流子浓度为1.60×10¹⁸ cm^-3时, 热电功率因子出现极大值4.72×10^-4 W/mK²; 由于Si杂质浓度的增加, 增强了GaN薄膜中的声子散射, 使得GaN薄膜的热导率随着载流子浓度的增加而降低. GaN薄膜的载流子浓度为1.60×10¹⁸ cm^-3时, 室温ZT达到极大值0.0025.     

A simulation study on p-doping level of polymer host material in P3HT:PCBM bulk heterojunction solar cells

In this study,we investigate the influence of doping on the charge transfer and device characteristics parameters in the bulk heterojunction solar cells based on poly(3-hexylthiophene)(P3HT) and a methanofuUerene derivative(PCBM).Organic semiconductors are also known to be not pure and they have defects and impurities,some of them are being charged and act as p-type or n-type dopants.Calculations of the solar cell characteristics parameters versus the p-doping level have been done at three different n-dopings(N_d) that consist of 5 × 10~(17) cm~(-3),10~(18) cm~(-3),and 5 × 10~(18) cm~(-3).We perform the analysis of the doping concentration through the drift-diffusion model,and calculate the current and voltage doping dependency.We find that at three different n-dopant levels,optimum p-type doping is about N_p = 6 × 10~(18) cm~(-3).Simulation results have shown that by increasing doping level,V_(oc) monotonically increases by doping.Cell efficiency reaches its maximum at somewhat higher doping as FF has its peak at N_p = 3 × 10~(18) cm~(-3).Moreover,this paper demonstrates that the optimum value for the p-doping is about N_p = 6 × 10~(18) cm~(-3) and optimum value for n-dopant is N_d = 10~(18) cm~(-3),respectively.The simulated results confirm that doping considerably affects the performance of organic solar cells.     

Er3+/Yb3+共掺锗碲酸盐玻璃的光谱性质及Judd-Ofelt理论分析

用高温熔融法制备了一种Er³⁺/Yb³⁺共掺的70TeO₂-5Li₂O-10B₂O₃-15GeO₂玻璃,测试和分析了其热稳定性、吸收光谱、荧光光谱以及红外吸收谱。应用Judd-Ofelt理论计算了玻璃中Er³⁺的强度参数、自发辐射跃迁几率、辐射寿命以及荧光分支比,同时比较了OH^-的存在对玻璃发光特性的影响。结果表明:这种玻璃具有较好的热稳定性,较宽的荧光半峰全宽和较大的受激发射截面,是一种较为合适的宽带光纤放大器的基质材料,OH^-的存在使得Er³⁺离子的荧光强度降低,荧光寿命减小。