Nd0.7Sr0.3MnO3陶瓷EPIR效应的起源

用两线法和四线法对球磨合成后热处理的Nd_0.7Sr_0.3MnO₃陶瓷样品的电脉冲诱导电阻转变(EPIR)效应进行了测试.结果表明:在Nd_0.7Sr_0.3MnO₃块体中用四线法测得的I-V曲线为非线性,说明Nd_0.7Sr_0.3MnO₃样品在晶(相)界处存在空间电荷层和界面电阻.但用四线法测量EPIR效应时,没有EPIR效应发生,表明晶(相)界处的空间电荷层和肖特基势垒不能产生EPIR效应;对同一样品采用直流两线法测量,其I-V曲线也为非线性,但却发生明显的EPIR效应.说明在Nd_0.7Sr_0.3MnO₃陶瓷中发现的EPIR效应起源于样品与电极之间的接触界面,块体内的晶(相)界处虽能产生相似I-V特性,但却不能发生EPIR效应. 关键词： 电脉冲诱导电阻转变(EPIR) 亚锰酸盐 空间电荷层 I-V非线性')" href="#">I-V非线性     

Ag/Nd0.7Sr0.3MnO3陶瓷界面电输运性质研究

用渗银和银胶接触两种方法分别在多晶Nd_0.7Sr_0.3MnO₃陶瓷样品上制作电极,用两线和四线模式对两种接触界面的直、交流特性进行测量.结果发现:渗银电极与陶瓷样品之间具有很好的欧姆接触特性,两线、四线模式下的电阻测量值相近,并且没有电脉冲诱导电阻转变(EPIR)效应;而用银胶接触作电极时,V-I曲线表现出关于原点对称的非线性特征,并出现稳定的室温EPIR效应.两种不同方法制备的电极在交流电场下的输运也有很大差异:渗银电极阻抗 关键词： 界面 接触电阻 EPIR效应 钙钛矿结构锰氧化物     

Nd0.7Sr0.3MnO3陶瓷中界面“陷阱态”相关电阻转变行为

通过固相烧结和高能球磨后热处理两种方法分别得到不具晶(相)界和具有明显晶(相)界的两种Nd_0.7Sr_0.3MnO₃陶瓷样品, 并用两线法和四线法分别对这两种样品的电极-块体接触界面和晶(相)界界面的I-V和电脉冲诱导电阻转变效应(EPIR)进行研究. 结果发现, 在两线法测试下, 电极-块体界面具有回滞的非线性I-V特征, 并能产生稳定的EPIR效应, EPIR的稳定性随温度的升高逐渐减弱并消失; 而对具有明显晶(相)界的陶瓷样品, 四线法测试结果表明, 虽然其I-V行为也具有非线性和回滞性特点, 但不能产生EPIR 效应. 这些奇特的界面输运行为与界面中的各种缺陷充当“陷阱”并实现对载流子的捕捉和释放过程密切相关. 而大量的晶(相)界界面及其复杂的连接方式导致较大的漏导则是晶(相)界不能出现EPIR效应的主要原因.     

Nd0.7Sr0.3MnO3中显微结构相关电致电阻效应

用固相反应和高能球磨合成后续热处理两种方法分别得到钙钛矿结构Nd_0.7Sr_0.3MnO₃氧化物.两种不同方法得到的多晶样品,虽然晶体结构相同,化学成分和晶粒大小相近,但它们电输运性质却表现出很大差异.用固相反应法制得的样品的电阻几乎不随负载电流的变化而变化,即不表现电致电阻行为;而通过高能球磨合成后续热处理方法得到的样品电阻随外加电流增大而急剧减小,出现显著电致电阻效应.产生这种截然不同电输运特性的原因可能与样品的显微结构和界面性质有关. 关键词： 电致电阻效应 显微结构 钙钛矿结构锰氧化物 界面电阻     

Nd1-xSrxMnO3中掺杂浓度对电脉冲诱导电阻转变效应的影响

采用两线测量模式对固相烧结方法制备的Nd_1-xA_xMnO₃ (A= Ba, Ca, Sr,x= 0-0.9) 陶瓷样品电脉冲诱导电阻转变(EPIR)效应和I-V特性进行了测量. 结果表明, 与Nd_0.7Sr_0.3MnO₃一样, 相同浓度掺杂的Nd_0.7Ba_0.3MnO₃和Nd_0.7Ca_0.3MnO₃ 样品也能诱发稳定的室温EPIR效应. 进一步对Nd_1-xSr_xMnO₃系列样品的EPIR研究表明, 这种界面相关的EPIR效应与样品中电子或空穴掺杂浓度密切相关, 在半掺杂 (x= 0.5)附近, 样品与电极接触界面能诱发稳定的EPIR效应. 然而, 随掺杂浓度的进一步增大或降低, EPIR效应逐渐出现减弱、不明显到完全消失的过程. 产生这种现象的原因可能与锰氧化物中由于掺杂浓度差异所导致的界面缺陷在不同极性脉冲激励下重新分布而产生的内电场强弱有关.     

Nd0.67Sr0.33MnOy(y<3.0)中的自旋相关电致电阻效应

用固相反应法制备系列Nd_0.67Sr_0.33MnO_y(y = 3.00—2.80)多晶样品.样品输运性质表现出自旋相关电致电阻特征.对氧含量等于化学计量样品，在测量温度范围内电阻不随负载电流变化，I-V曲线符合线性欧姆定律.对氧含量低于化学计量样品，当高于某一特征温度时，电阻变化符合线性欧姆定律；但低于这一特征温度时，电阻大小与负载电流有关，I-V曲线偏离线 关键词： 钙钛矿结构锰氧化物 电致电阻效应 自旋相关界面输运 氧缺陷     

Ti/Pr0.7Ca0.3MnO3/La0.67Sr0.33MnO3/Pt异质结电致电阻效应的改善

采用脉冲激光沉积技术制备了Ti/Pr_0.7Ca_0.3MnO₃/Pt和Ti/Pr_0.7Ca_0.3MnO₃/La_0.67Sr_0.33MnO₃/Pt异质结并研究了La_0.67Sr_0.33MnO₃功能插层对异质结电致电阻特性的影响. 实验结果表明La_0.67Sr_0.33MnO₃功能层的引入有效提高了器件的电阻转变特性,尤其是电阻转变率和疲劳性得到了极大的改善. 对La_0.67Sr_0.33MnO₃插层改善电致电阻转变特性的机理进行了定性的分析. 关键词： 电致电阻效应 电阻转变比率 疲劳特性     

钙钛矿结构Pr1－xCaxMnO3薄膜中电脉冲诱导电阻值变化的理论研究

建立一个有效的三明治隧穿模型研究在Pr_1-xCa_xMnO₃薄膜中电流脉冲引起的电阻改变(EPIR)性质，发现载流子在三明治结构各区域间的隧穿概率以及在不均匀界面层的导通概率对材料的EPIR值产生重要影响.还研究了电流-电压曲线中的迟滞效应，得到的结果与近年来的文献报道一致. 关键词： 强关联电子系统 金属-氧化物界面 隧穿     

点接触金属/Pr$lt;sub$gt;0.7$lt;/sub$gt;Ca$lt;sub$gt;0.3$lt;/sub$gt;MnO$lt;sub$gt;3$lt;/sub$gt;/Pt结构稳定的低电流电阻开关特性

利用自主开发的导电原子力显微镜控制Pt,W探针构成点接触金属/Pr_0.7Ca_0.3MnO₃（PCMO）/Pt三明治结构,对其电流-电压（I-V）及脉冲诱导电阻开关（EPIR）特性进行了研究.研究发现,在10 nA限流下两种电极对应结构的I-V都表现出相当稳定的双极性电阻开关特性,以及大于100的电阻开关比.进一步测试发现,点接触W/PCMO/Pt器件具有在10 nA限流下稳定的EPIR特性以及100 pA限流下重复的双极性电阻开关特性.此电流比已报道的电流低3个数量级,表明此结构在低功耗存储器件方面的潜在应用.通过对比样品不同位置、不同限流、不同接触面积点接触Pt/PCMO/Pt的I-V回滞特性,把点接触器件在低电流下稳定、显著的电阻开关效应归结于小的器件面积导致强的局域电场加强了O离子迁移效应. 关键词： 脉冲诱导电阻开关 电场下氧离子迁移 电阻开关     

Au/SrTiO3/Au界面电阻翻转效应的低频噪声分析

本文研究了Au/SrTiO₃/Au三明治结构中的双极电阻翻转效应, 观察到高、低阻态的电阻弛豫现象. 低频噪声测量表明高、低阻态的电阻涨落表现出1/f行为. 对比试验表明, 高阻态的低频噪声来源于反向偏置肖特基势垒和氧空位的迁移, 强度较大, 低阻态的噪声则源于类欧姆接触底电极区域的氧空位迁移导致的载流子涨落, 强度较低. 同时, 界面上氧空位浓度的弛豫导致了高、低阻态的弛豫过程. 关键词： 电阻翻转效应 低频噪声 氧空位     

Structural and electrical characterisation of La0.5Ca0.5MnO3 thin films grown by pulsed laser deposition

Thin films of perovskite manganite, with nominal composition La_0.5Ca_0.5MnO₃, have been prepared by pulsed laser deposition on (1 0 0) SrTiO₃, (1 0 0) LaAlO₃, (1 0 0) Si and YSZ/CeO₂-buffered (1 0 0) Si substrates. Structural and electrical characterisation was performed on the films. The magneto-transport properties of all the thin films depart from the bulk behaviour. The LCMO film grown on buffered Si shows an insulator–metallic transition around 130–150 K while the one deposited directly on Si displayed a similar behaviour under a melting field of 1 T. However, that transition is absent in the films grown on LAO and STO. We suggest that appropriate stress values induced by the substrate favour the formation of metallic percolative paths.     

Dynamical effects in magnetic and transport properties of phase separated La0.5Ca0.5Mn0.95Fe0.05O3

We have measured transport and magnetic properties of polycrystalline La_0.5Ca_0.5Mn_0.95Fe_0.05O₃, a phase separated manganite with ferromagnetic ground state. Cooling rate dependences and time relaxation were found; the coexistence of ferromagnetic and charge ordered regions determines a dynamics which influences physical properties. We show that a dynamical contribution to the resistivity can account for the observed cooling rate dependence and ageing effects on this phase separated manganite.     

p型GaN/Al0.35Ga0.65N/GaN应变量子阱中二维空穴气的研究

对Ga面p型GaN/Al_0.35Ga_0.65N/GaN应变异质结构中形成的二维空穴气(2DHG)进行了研究.首先基于半导体-绝缘体-半导体异质结构模型确定了应变异质中的临界厚度，然后自洽求解薛定谔方程和泊松方程，计算了当中间势垒层AlGaN处于完全应变状态和半应变状态两种条件下，顶层GaN及中间层AlGaN厚度的变化对2DHG分布的影响.计算结果表明，势垒层AlGaN和顶层GaN的应变状态和厚度对极化引起的2DHG面密度及分布有重要影响.在此基础上制备了p型GaN/Al_0.35Ga_0.65N/GaN应变量子阱结构肖特基器件，并通过器件的C-V测试证实了异质结处2DHG的存在.器件响应光谱的测试结果表明，由于p型GaN/Al_0.35Ga_0.65N/GaN量子阱中强烈的极化作用和Stark效应使得器件零偏压和反向偏压时的响应光谱都向短波方向移动了10 nm，在零偏压下器件在280 nm处的峰值响应为0.022 A/W，在反向偏压为1 V时，峰值响应达到0.19 A/W，已经接近理论值. 关键词： AlGaN 二维空穴气 极化效应     

Rotation of ferromagnetic clusters induced magnetoresistance in the junction composed of La0.9Ca0.1MnO3 +δ and 1 wt.% Nb-doped SrTiO3

A junction composed of ultrathin La0.9Ca0.1MnO3＋δ （LCMO） film and 1 wt.% Nb-doped SrTiO3 was fabricated and its magnetoresistance （MR） was studied and compared with LCMO film. It was found that the resistance of the junction has a similar dependence on magnetic field as that of the LCMO film： the curvature of R-H curves is upward above Curie temperature （Tc） and downward below TC. These behaviours strongly suggest that the rotation of ferromagnetic clusters in manganite also causes MR in the corresponding junction. This MR can be qualitatively understood by the change of the width of the barrier induced by the rotation of ferromagnetic clusters. These results suggest a possibility to obtain junctions with large low-field MR.     

Transverse laser induced thermoelectric voltage effect in tilted La0.5Sr0.5CoO3 thin films

The transverse laser induced thermoelectric voltage effect has been investigated in tilted La_0.5Sr_0.5CoO₃ thin films grown on vicinal cut LaAlO₃ (1 0 0) substrates when films are irradiated by pulse laser at room temperature. The detected voltage signals are demonstrated to originate from the transverse Seebeck effect as the linear dependence of voltage on tilted angle in the range of small tilted angle. The Seebeck coefficient anisotropy ΔS of 0.03 μV/K at room temperature is calculated and its distorted cubic structure is thought to be responsible for this. Films grown on a series of substrates with different tilted angles show the optimum angle of 19.8° for the maximum voltage. Film thickness dependence of voltage has also been studied.     

Charge ordering characteristics in Y0.5Ca0.5MnO3 manganite

The charge ordering characteristics in Y_0.5Ca_0.5MnO₃ manganite, prepared by sol–gel process, have been investigated experimentally. It is found that the superlattice diffractions appear in the electron diffraction patterns recorded at low temperatures, while only basic Brag diffraction spots can be observed when temperature is higher than 300 K. This provides direct evidence for the existence of charge ordering in Y_0.5Ca_0.5MnO₃. The magnetization and specific heat measurements indicate the charge ordering temperature of Y_0.5Ca_0.5MnO₃ is 290 K, around which both the magnetization and specific heat reveal anomalous behaviors. We also observed that the MnO bond length changed remarkably and the effective number of carriers reduced prominently with decreasing temperature around charge ordering temperature through transform infrared spectra measurements.