界面电子转移对量子点荧光闪烁行为的影响

利用激光扫描共聚焦显微系统分别测量了CdSe/ZnS量子点在SiO2玻片表面、铟锡氧化物(ITO)纳米粒子表面和聚甲基丙烯酸甲酯(PMMA)薄膜表面上的荧光闪烁行为.研究发现,不同界面环境中量子点的亮态发光持续时间的概率密度都服从指数修正的幂律分布P(t)∝t-αexp(-t/μ).与处于SiO2玻片表面的情况相比,在ITO表面上的单量子点具有非常短暂的亮态发光持续时间,而在PMMA表面的单量子点亮态发光持续时间最长.这种荧光闪烁行为的不同主要归因于量子点与三种材料之间的界面电子转移特性.     

2018年2期电子期刊

光诱导功能退化是胶体量子点在应用中面临的主要挑战之一,本文针对这一问题研究了使用磁控溅射沉积SiO₂薄膜形成钝化层来提高CdSe/ZnS量子点发光稳定性的方法。首先,通过三正辛基膦辅助连续离子层吸附反应方法合成了615 nm发光的红色CdSe/ZnS量子点。然后将量子点旋涂在SiO₂/Si基片上,再通过磁控溅射方法在量子点上沉积了厚度为20 nm的SiO₂薄膜作为钝化层。使用连续波激光光源分别在空气气氛和真空条件下照射样品,研究了经过不同照射时间后钝化和未钝化量子点的稳态光致发光光谱。结果表明,随着照射时间的延长,没有SiO₂钝化的量子点的PL强度显著降低、PL峰值发生蓝移、FWHM不断增大。对比研究发现,由于SiO₂薄膜能够阻挡空气中的水和氧,减缓了量子点表面的光诱导氧化现象,因此显著提高了CdSe/ZnS量子点的稳定性。     

ZnS：Mn/SiO2量子点的表面聚乙烯吡咯烷酮修饰及其应用于海水中铅离子检测

制备了二氧化硅壳层修饰的ZnS：Mn量子点,基于聚乙烯吡咯烷酮（PVP）与二氧化硅表面硅羟基的作用,在纳米复合微粒表面进行了PVP的修饰,得到了在海水中荧光性能及胶体稳定性良好的ZnS：Mn/SiO₂/PVP 量子点。在Pb²⁺对所制备纳米微粒具有荧光猝灭效应的基础上,建立了用ZnS：Mn/SiO₂/PVP 量子点作为荧光探针检测海水中微量铅离子的新方法。研究表明,量子点浓度为10^-3 mol/L时,海水中离子浓度在10~100 μmol/L范围内与ZnS：Mn/SiO₂/PVP量子点荧光猝灭强度呈良好的线性关系,相关系数为0.994 6,检出限为8×10^-7 mol/L。     

CdSe量子点凝胶快速制备及其光谱特性

以水为反应溶剂,采用NaBH₄还原SeO₂并与过量CdSO₄反应,制备CdSe量子点凝胶。所得CdSe量子点凝胶直接干燥即得到固态粉体,若用聚乙二醇或谷胱甘肽等作为分散修饰剂可方便的转化成相应的溶胶,制备方法快速简单、成本低。CdSe量子点凝胶、粉体、溶胶均具有良好的光致发光特性,且性质稳定。结果表明反应物CdSO₄与SeO₂用量的摩尔比（Cd/Se值）和反应温度影响CdSe量子点的荧光特性。当制备凝胶的Cd/Se值由2.4:1增加12:1时,CdSe量子点-聚乙二醇溶胶的荧光强度增加,荧光发射峰由560nm红移到610nm;当制备凝胶的反应温度由40℃增加到90℃时,CdSe量子点-聚乙二醇溶胶的荧光发射峰由560nm红移到600nm。CdSe量子点-聚乙二醇溶胶的荧光量子产率20%左右。     

ZnS薄膜参数对有机/无机复合发光器件特性的影响

半导体量子点(QDs)具有发光效率高和发光波长可调等特点。采用胶体CdSe QDs作电致发光器件的有源材料,TPD(N,N′-biphenyl-N,N′-bis-(3-methylphenyl)-1,1′-biphenyl-4,4′-diamine)作空穴传输层,ZnS作电子传输层,研究了有机/无机复合发光器件ITO/TPD/CdSe QDs/ZnS/Ag的电致发光特性。TPD和CdSe QDs薄膜采用旋涂方法、ZnS薄膜采用磁控溅射方法沉积,器件表面平整。CdSe QDs的光致发光和电致发光谱峰位波长均位于～580 nm,属于量子点的带边激子发光。我们与以前的ITO/ZnS/CdSe QDs/ZnS/Ag发光器件结构进行了对比,发现新的器件结构的电致发光谱没有观察到QDs表面态的发光,而且新器件的发光强度是ITO/ZnS/CdSe QDs/ZnS/Ag结构的～10倍。发光效率的提高归因于碰撞激发与载流子注入两种发光机制并存的结果：一方面电子经过ZnS 层加速后,碰撞激发CdSe QDs发光;另一方面,空穴从TPD层注入CdSe QDs 与QDs中激发的电子复合发光。我们进一步研究了ZnS电子加速层厚度对发光特性的影响,选择ZnS薄膜的厚度分别是80,120 和160 nm,发现随着ZnS层厚度增大,器件启亮电压升高,EL强度增大,但是击穿电压降低。EL峰位随着ZnS厚度的减小发生明显蓝移,对上述实验现象进行了机理解释。     

SiO2包覆对ZnS纳米材料发光的增强机制

为了明确团聚现象及表面性质对ZnS纳米材料发光性质的影响,采用SiO₂对ZnS材料进行了表面修饰,并对ZnS及ZnS/SiO₂复合材料的光学性质进行对比研究.采用吸收光谱分析了包覆前后光吸收性质的差异,发现SiO₂包覆后ZnS纳米材料的带边由333 nm红移至360 nm.为了研究ZnS纳米材料与ZnS/SiO₂纳米复合材料的光发射性质,分别对含纳米材料的水溶液样品及粉末样品的发光光谱进行了采集.对比研究的结果表明,SiO₂包覆后ZnS纳米材料在蓝紫光区的发光得到了明显增强.以氙灯作为激发光源所获得荧光光谱显示ZnS/SiO₂粉末样品发光的积分强度增大为原来的17.5倍,但相同条件下针对溶液样品的测试结果显示其发光强度只增大了1.1倍,这种增强可用SiO₂的存在抑制了ZnS纳米粒子间的团聚来解释,且这一推断由325 nm紫外激光激发下获得的光致发光数据进行了验证.     

脂溶性CdSe/ZnS量子点脂质体复合物的制备及表征

在油相中成功合成了脂溶性CdSe/ZnS核壳量子点纳米粒,粒径平均为4.5 nm,量子产率达29%,发射波长为540 nm。通过薄膜分散法,以蛋黄卵磷脂、胆固醇为膜材,将脂溶性的CdSe/ZnS核壳量子点包覆于脂质体磷脂双分子层中,由于磷脂分子的两亲性,使得脂溶性的CdSe/ZnS核壳量子点同时又具有亲水性。通过透射电镜对脂质体形态进行了表征,倒置荧光显微镜证实了发光CdSe/ZnS核壳量子点成功包埋于脂质体双分子层中,包裹的发光CdSe/ZnS核壳量子点具有更稳定的发光及抗光漂白性质。     

生物大分子杂化处理的CdSe/ZnS核/壳量子点多层膜的超快三阶非线性研究

利用静电自组装技术，以生物大分子材料壳聚糖杂化处理具有稳定结构的CdSe/ZnS核/壳量子点，形成复合多层薄膜. 与薄膜的吸收谱线比较，在375nm飞秒激光激发下测量的量子点的光致发光谱存在Stokes位移. 采用Z扫描技术，利用790nm飞秒激光研究了其三阶非线性吸收和折射特性，发现饱和吸收信号来自CdSe/ZnS量子点，而自聚焦的折射信号则部分来自壳聚糖. 测出多层膜的三阶非线性系数分别是β＝6.5×10^-6cm/W，n₂＝1.5×10^-10cm²/W. 关键词： CdSe/ZnS量子点 非线性性能 光致发光谱     

空穴传输材料对CdSe核壳量子点的荧光影响

用稳态光谱和时间分辨光谱技术研究了空穴传输材料对CdSe/ZnSe 与CdSe/ZnS核壳量子点的荧光影响。结果表明,空穴传输材料对量子点有较强的猝灭作用,随空穴传输材料分子浓度的增加,量子点的荧光强度明显地被猝灭,同时量子点的荧光寿命也被减短。两种不同空穴传输分子对CdSe/ZnSe量子点的荧光猝灭明显不同。在与相同空穴传输分子相互作用时,包覆ZnS壳层的CdSe核壳量子点荧光猝灭效率明显低于包覆ZnSe壳层的CdSe核壳量子点。量子点的荧光猝灭过程可以解释为静态猝灭和动态猝灭过程,其中静态猝灭来源于量子点表面与空穴传输材料间相互作用,而动态猝灭则主要来源于量子点到空穴传输材料的空穴转移过程。实验结果表明空穴传输材料的种类以及核壳量子点的壳层结构都对其荧光猝灭效应起关键作用。     

巯基乙胺稳定合成CdSe量子点及其发光性能的研究

CdSe量子点是一种重要的半导体纳米材料。以巯基乙胺(CA)为稳定剂,CdCl₂·2.5H₂O为镉源,SeO₂为硒源,采用简单的一步水相法合成水溶性的CdSe量子点。详细地研究了加热回流时间、初始pH值、硒与镉的摩尔比和回流温度等实验条件对CdSe量子点发光性能的影响。利用X-射线粉末衍射、透射电子显微镜、紫外-可见光谱和荧光光谱等表征量子点的结构和光学性能。结果表明,采用巯基乙胺为稳定剂制备的CdSe量子点为立方晶相,颗粒大小约为2.0nm,量子点的荧光发射峰在560～589nm内连续可调。     

Size dependence of biexciton binding energy in single InAs/GaAs quantum dots

This paper studies the size dependence of biexciton binding energy in single quantum dots (QDs) by using atomic force microscopy and micro-photoluminescence measurements. It finds that the biexciton binding energies in the QDs show ``binding' and ``antibinding' properties which correspond to the large and small sizes of QDs, respectively. The experimental results can be well interpreted by the biexciton potential curve, calculated from the exciton molecular model and the Heitler--London method.     

PbS纳米颗粒复合的溶胶凝胶薄膜的飞秒非线性光学特性

通过光Kerr效应研究了PbS半导体纳米颗粒的三阶光学非线性响应。在较低的激发强度下,单激子态的饱和吸收和双激子效应的激发态吸收对非线性的贡献同时存在;而在高激发强度下,双激子效应是主要的。计算了高激发强度下(4mJ/cm²)PbS半导体纳米颗粒的三阶非线性光学极化率为5.1×10^-10esu。     

Coherent dynamics in InGaAs quantum dots and quantum dot molecules

We measure the dephasing time of the exciton ground state transition in InGaAs quantum dots (QD) and quantum dot molecules (QDM) using a sensitive four-wave mixing technique. In the QDs we find experimental evidence that the dephasing time is given only by the radiative lifetime at low temperatures. We demonstrate the tunability of the radiatively limited dephasing time from 400 ps up to 2 ns in a series of annealed QDs with increasing energy separation of 69–330 meV from the wetting layer continuum. Furthermore, the distribution of the fine-structure splitting δ₁ and of the biexciton binding energy δ_B is measured. δ₁ decreases from 96 to with increasing annealing temperature, indicating an improving circular symmetry of the in-plane confinement potential. The biexciton binding energy shows only a weak dependence on the confinement energy, which we attribute to a compensation between decreasing confinement and decreasing separation of electron and hole. In the QDM we measured the exciton dephasing as function of interdot barrier thickness in the temperature range from 5 to 60 K. At 5 K dephasing times of several hundred picoseconds are found. Moreover, a systematic dependence of the dephasing dynamics on the barrier thickness is observed, showing how the quantum mechanical coupling in the molecules affects the exciton lifetime and acoustic-phonon interaction.     

Near-field optical mapping of exciton wave functions in a GaAs quantum dot

Near-field photoluminescence imaging spectroscopy of naturally occurring GaAs quantum dots (QDs) is presented. We successfully mapped out center-of -mass wave functions of an exciton confined in a GaAs QD in real space due to the enhancement of spatial resolution up to 30 nm. As a consequence, we discovered that the spatial profile of the exciton emission, which reflects the shape of a monolayer-high island, differs from that of biexciton emission, due to different distributions of the polarization field for the exciton and biexciton recombinations. This novel technique can be extensively applied to wave function engineering in the design and the fabrication of quantum devices.     

Surface integral determination of built-in electric fields and analysis of exciton binding energies in nitride-based quantum dots

We present a simple analytical approach to calculate the built-in strain-induced and spontaneous piezoelectric fields in nitride-based quantum dots (QDs) and then apply the method to describe the variation of exciton, biexciton and charged exciton energy with dot size in GaN/AlN QDs. We first present the piezoelectric potential in terms of a surface integral over the QD surface, and confirm that, due to the strong built-in electric field, the electrons are localised near the QD top and the holes are localised in the wetting layer just below the dot. The strong localisation and smaller dielectric constant results in much larger Coulomb interactions in GaN/AlN QDs than in typical InAs/GaAs QDs, with the interaction between two electrons, J_ee, or two holes, J_hh, being about a factor of three larger. The electron–hole recombination energy is always blue shifted in the charged excitons, X⁻ and X⁺, and the biexciton, and the blue shift increases with increasing dot height. We conclude that spectroscopic studies of the excitonic complexes should provide a useful probe of the structural and piezoelectric properties of GaN-based QDs.     

Photo-physical and lasing characterisation of a polyparaphenylenevinylene (PPV) neat film

The wave-guided travelling-wave laser action (amplified spontaneous emission) of a neat film of poly(p-phenylenevinylene) (PPV) on a quartz glass substrate prepared by a sulfinyl precursor technique is studied. The samples are transversally pumped with picosecond excitation pulses (wavelength 347.15 nm, duration 35 ps). Lasing occurs at 550 nm. The optical constants of the neat films are determined by transmittance measurements exploiting the multiple beam interference in the transparency region. A fluorescence spectroscopic characterisation is carried out determining the fluorescence quantum distribution, fluorescence quantum yield, degree of fluorescence polarisation, and fluorescence lifetime. The emitting chromophore size (emitting singlet exciton extension) is determined by the ratio of exciton radiative lifetime to repeat-unit based radiative lifetime. The obtained size of about two repeat units is discussed in a disordered solid-state polymer model.     

自组织生长InAs/GaAs量子点发光动力学研究

介绍了最新发展的粒子数混合超快光谱测量技术,以及采用该技术对自组织生长InAs/GaAs量子点发光动力学的研究结果.实验发现,自组织InAs/GaAs量子点结构的发光寿命大约为1ns,与InAs层厚度关系不大;激子寿命与温度有一定的关系,但没有明显的实验证据表明与量子点的δ态密度有关;用粒子数混合技术,实验上可直接观察到量子点中载流子在激发态能级的态填充过程. 关键词：     

Influence of surface charges on the emission polarization properties of single CdSe/CdS dot-in-rods

We report an experimental investigation of the influence of surface charges on the emission polarization properties of single CdSe/CdS dot-in-rods (DRs), which is important for their polarization-based practical applications. By covering the single DRs with N-type semiconductor indium tin oxide (ITO) nanoparticles, the surface of single DRs is charged by ITO through interfacial electron transfer. This is confirmed by the experimental observations of the reduced photoluminescence intensities and lifetimes as well as the suppressing blinking. It is found that the full width at half maximum of histogram of polarization degrees of the single DRs is broadened from 0.24 (on glass) to 0.41 (in ITO). In order to explain the exprimental results, the band-edge exciton fine structure of single DRs is calculated by taking into account the sample parameters, the emission polarization, and the surface charges. The calculation results show that the level ordering of the emitting states determines the polarization degrees tending to increase or decrease under the influence of surface electrons. The surface electrons can induce an increase in the spacing between the emitting levels to change the populations and thus change the polarization degrees. In addition, different numbers of surface electrons may randomly distribute on the long CdSe/CdS rods, leading to the heterogeneous influences on the single DRs causing the broadening of polarization degrees also.