新型苯乙烯衍生物掺杂的蓝色及白色有机电致发光器件

研究了新型高效蓝色掺杂剂EBDP的电致发光性能. 分别以EBDP为掺杂剂制备了结构为氧化铟 锡(ITO)/酞菁铜(CuPc)/N,N′-二(1-萘基)-N,N′-二苯基-1,1′-联苯-4-4′-二胺(NPB)/2- 叔丁基-9,10-二-(2-萘基)蒽(TBADN):EBDP/8-羟基喹啉铝(Alq₃)/LiF/Al 与ITO /CuPc/NPB/TBADN:EBDP: 4-二氰亚甲基-2-叔丁基-6-(1,1,7,7-四甲基久咯呢定基-9-烯基)- 4H-吡喃/Alq_{3 关键词： 有机电致发光 蓝色掺杂剂 蓝色电致发光器件 白色电致发光器件}     

掺杂两种荧光染料的有机红光电致发光器件

制作了掺杂rubrene和4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9,enyl)-4H-pyran(DCJTB)两种荧光染料的红光有机电致发光器件。N,N’-diphenyl-N,N’-bis(1-naphthyl)-(1,1’-biphenyl)-4,4’-diamine(NPB)和掺杂的Tri-(8-hydroxyquinoline)aluminum(Alq3)分别作为空穴和电子传输层。我们发现掺rubrene和DCJTB的器件性能与只掺DCJTB的器件性能相比有所提高。器件性能的改善是因为掺入的rubrene能够促进从Alq3到DCJTB的能量转移。根据荧光衰减曲线,计算出从Alq3到DCJTB、从Alq3到rubrene以及从rubrene到DCJTB的能量转移速率分别为1.04×109,3.89×109,2.79×109s-1。可以看出能量通过rubrene从Alq3到DCJTB的转移速率是能量直接从Alq3到DCJTB的2.7倍。     

基于新型腈类染料的白色有机电致发光器件的光谱特性

将腈类黄色荧光染料(2Z,2’Z)-3, 3’-(1,4-phenylene)bis(2-phenylacrylonitrile) (BPhAN)掺杂到poly(N-vinylcarbazole) (PVK)中作发光层,2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP)作电子传输层和空穴阻挡层,制备了结构为Indium-tin oxide (ITO)/PVK∶BPhAN/BCP/Mg∶Ag的双层有机电致发光器件。通过调节BPhAN掺杂质量百分比(2 wt%, 4 wt%, 6 wt%),测试了器件在不同电压下的光谱特性,研究了Frster能量转移和直接载流子俘获在发光过程中的作用。结果表明,当掺杂浓度为4 wt%时可实现色度较好的白光,随着电压从6 V增大到16 V,CIE色坐标从(0.33, 0.37)变化到(0.32, 0.33),在白光区域有微小蓝移,这是由于随着电压的增大,能量转移效率和直接载流子俘获效率都降低,BPhAN黄光减弱,PVK发射的蓝光增强。     

白色有机薄膜电致发光

198 7年柯达公司 C.W.Tang发表的有机薄膜电致发光[1] 因其在平板显示技术中的巨大应用前景而成为当前研究的热点。白色发光因是实现全彩色平板显示的重要方案之一 ,而倍受人们的关注。目前已有一些有关白光的报道 ,J.Kido[2 ,3]利用多层结构及三种染料掺杂的polymer实现白光 ,S.R.Forrest[4 ] 利用叠层实现白光 ,Y.Sato[5] 用了一种新的掺杂剂得到白光 ,M.Granstrom[6 ]和 Y.Yang[7]报道了polymer的白色发射。在这篇文章中 ,将报道一种利用锁定层中掺杂染料来实现白色有机电致发光的器件 ,其最高亮度达 863 5 cd/ m2 ,最大效率为1 .3…     

利用p型掺杂技术制备的高效有机电致发光器件

利用氧化钼(MoO_x)作为p型掺杂剂,以掺杂层4,4'-bis(carbazol-9-yl)biphenyl(CBP):MoO_x作为空穴注入层,制备了一种结构为ITO/MoO_x/CBP:MoO_x/CBP/CBP:tris(2-phenylpyridine)iridium(III)(Ir(ppy)₃)/4,7-diphenyl-1,10-phenanthroline(Bphen)/LiF/Al的有机电致发光器件.器件中CBP同时作为空穴注入层、空穴传输层以及发光层母体材料,这种结构具有结构简单同时能有效降低空穴注入势垒等优点.研究发现,随着空穴注入层厚度的增加,器件的电流密度增加,表明p型掺杂层的引入能够有效增强空穴的注入;通过优化器件空穴注入层与空穴传输层厚度,器件性能有所提高,最大电流效率为29.8 cd/A,可以认为合理的优化空穴注入层和空穴传输层的厚度,使载流子在发光层中的分布更加平衡是提高器件发光效率的主要原因.值得指出的是,从电流效率最大值到亮度为 20 000 cd/m²时,优化后器件的效率衰减仅为17.7%,而常规器件的效率衰减则为62.1%,优化后器件效率衰减现象得到了明显的改善.分析认为优化后的器件中未掺杂的CBP有助于展宽激子形成区宽度,进而减弱了三线态-三线态湮灭、三线态-极化子淬灭现象,激子形成区的展宽是改善效率衰减的主要原因.     

利用有机层间互相掺杂提高有机电致发光器件的效率

提高器件的发光效率是实现有机电致发光器件实用化的一个关键因素。通过对器件结构和制作工艺的优化设计，将有机电致发光器件的各个功能层进行互相掺杂，在层间形成互掺过渡层达到平衡载流子的注入，使得注入的电子和空穴有效地限制在互掺的有源区内，增加了载流子相遇复合的几率，进而提高器件的发光效率。器件的最大电流效率在外加电压10．5V时达到7．9cd／A，最大发光亮度在35V时达到49000cd／m^2。和一般掺杂器件相比效率提高2倍以上。同时有机层间的互相掺杂也在一定程度上消除了层问的界面，减少了有机层问的缺陷，与没有过渡层的器件相比，器件老化性能有了明显改善。     

荧光染料掺杂的高效率、高亮度白色有机电致发光器件

制备了结构为 ITO/NPB（30 nm）/Rubrene（0.2 nm）/CBP：Bczvbi（8 nm,x%）/Bphen（30 nm）/Cs₂CO₃：Ag₂O（2 nm,20%）/Al（100 nm）的器件。研究了Bczvbi掺杂浓度（x=5,10,15）对白光器件性能的影响。综合利用发光层中主客体之间的能量转移和空穴阻挡层的空穴阻挡特性,得到了高效率、高亮度的白色有机电致发光器件。当Bczvbi的掺杂质量分数为10%时,器件的效率和亮度都为最大。驱动电压为7 V时,最大电流效率为4.61 cd/A;驱动电压为9 V时,最大亮度为21 240 cd/m²。当驱动电压从4 V增加到9 V时,色坐标从（0.36,0.38）变化为（0.27,0.29）,均处于白光区域。     

TBPe与MEH-PPV共掺杂的有机电致发光器件的优化研究

采用有机小分子TBPe（2,5,8,11-tetratertbutylperylene）以不同比例掺入MEH-PPV（poly ）作为发光层,研究了TBPe不同掺杂比例对器件性能的影响,进而对发光强度进行优化。对于所制备的ITO/PEDOT：PSS/MEH-PPV/TBPe/Al有机电致发光器件,TBPe的最优蒸镀厚度为0.5 nm,其发光强度相对于标准器件提高了325%。ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Liq/Al有机电致发光器件的最优掺杂比例为MEH-PPV：TBPe=100：30（质量比）,其发光亮度相比于未掺杂器件提高了44%。在上述器件的基础上增加Alq₃层提高电子注入,分别制作了Liq和LiF作为修饰层的ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/Liq/Al和ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/LiF/Al多层器件,发光亮度分别达到4 162 cd/m²和4 701 cd/m²。所有器件的电致发光波长均为580 nm,为MEH-PPV的发光,TBPe的掺杂对MEH-PPV的发光起到了增强作用。     

柔性衬底白色有机电致发光器件的制备及其性能

采用以ITO为导电层的柔性透明PET基片作为衬底,以2-(2-羟基苯基)苯并噻唑螯合锌(Zn(BTZ),)作为发光层制备出结构为PET／ITO／PVK：TPD／Zn(BTZ)2／Al明亮的近白色柔性有机小分子电致发光器件。发光的色坐标值为x=0．242,y=0．359,在25V的直流电压驱动下,亮度为1000cd／m^2,量子效率达到了0．30％。并进一步在Zn(BTZ)2中掺入橙红色染料Rubrene,制成PET／ITO／PVK：TPD／Zn(BTZ)2：Rubrene／Al结构器件。实现了纯白色发光(色坐标值：x=0．339,y=0．339),非常接近于白色等能点,驱动电压为25V时器件的亮度达1200cd／m^2,且量子效率达0．35％。最后对器件的发光性能及机理进行了深入的研究和探讨。     

TBPe与MEH-PPV共掺杂的有机电致发光器件的优化研究

采用有机小分子TBPe(2,5,8,11-tetratertbutylperylene)以不同比例掺入MEH-PPV(poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene])作为发光层,研究了TBPe不同掺杂比例对器件性能的影响,进而对发光强度进行优化。对于所制备的ITO/PEDOT∶PSS/MEH-PPV/TBPe/Al有机电致发光器件,TBPe的最优蒸镀厚度为0.5 nm,其发光强度相对于标准器件提高了325%。ITO/PEDOT∶PSS/MEH-PPV∶TBPe/TBPe/Liq/Al有机电致发光器件的最优掺杂比例为MEH-PPV∶TBPe=100∶30(质量比),其发光亮度相比于未掺杂器件提高了44%。在上述器件的基础上增加Alq3层提高电子注入,分别制作了Liq和LiF作为修饰层的ITO/PEDOT∶PSS/MEH-PPV∶TBPe/TBPe/Alq3/Liq/Al和ITO/PEDOT∶PSS/MEH-PPV∶TBPe/TBPe/Alq3/LiF/Al多层器件,发光亮度分别达到4 162 cd/m2和4 701 cd/m2。所有器件的电致发光波长均为580 nm,为MEH-PPV的发光,TBPe的掺杂对MEH-PPV的发光起到了增强作用。     

Non-doped phosphorescent white organic light-emitting devices with a quadruple-quantum-well structure

Non-doped white organic light-emitting devices (WOLEDs) with a quadruple-quantum-well structure were fabricated. An alternate layer of ultrathin blue and yellow iridium complexes was employed as the potential well layer, while potential barrier layers (PBLs) were chosen to be 2,2',2''-(1,3,5-benzenetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) or N,N'-dicarbazolyl-3,5-benzene (mCP) combined TPBi. On adjusting the PBLs for device performance comparison, the results showed that the device with all-TPBi PBLs exhibited a yellow emission with the color coordinates of (0.50,0.47) at a luminance of 1000 cd/m², while stable white emission with the color coordinates of (0.36,0.44) was observed in the device using mCP combined TPBi as the PBLs. Meanwhile, for the WOLED, with a reduced efficiency roll-off, a maximum luminance, luminous efficiency, and external quantum efficiency of 12,610 cd/m², 10.2 cd/A, and 4.4%, respectively, were achieved. The performance improvement by the introduction of mCP PBL was ascribed to the well confined exciton and the reduced exciton quenching effect in the multiple emission regions.     

Highly efficient all phosphorescent white organic light-emitting diodes for solid state lighting applications

We report highly efficient all phosphorescent white organic light-emitting diodes (OLEDs) with an exciton-confinement structure. By stacking two emissive layers (EMLs) with different charge transporting properties, effective charges as well as exciton confinements were achieved. Accordingly, efficient blue OLEDs with a peak external quantum efficiency (EQE) over 22% and power efficacy (PE) over 50 lm/W were developed by using iridium(III) bis(4,6-(difluorophenyl) pyridinato-N,C2′)picolinate (FIrpic) as an electro-phosphorescent dopant. When the optimized orange and red EMLs were sandwiched between the stacked two blue EMLs, white OLEDs with an EQE and PE of 24.3% and 45.9 lm/W at a luminance of 1000 cd/m² were obtained without the use of any out-coupling techniques. In addition, these white OLEDs exhibit a color rendering index (CRI) value of 84 with high efficacy.     

Improved performances of the organic light-emitting devices by doping in the mixed layer

The brightness, efficiency and lifetime of organic light-emitting diodes (OLEDs) were remarkably improved by doping in a mixed layer. In this device, the emitting layer consists of a mixture of -naphthylphenybiphenyl amine (NPB), tris (8-hydroxyquinolinolate) aluminum (Alq₃) (referred to as the mixed layer) and an emissive dopant 5,6,11,12-petraphenylnaphthacene (rubrene), where the concentration of NPB declined while the concentration of Alq₃ was increased gradually in the deposition process. The device exhibited a maximum emission of 49,300 cd/m² at a destroy voltage of 35 V and a maximum efficiency of 7.96 cd/A at 10 V, respectively. The efficiency improves twofold in comparison with the conventional doped devices. Meanwhile, the device exhibited superior operational stability with a half-life time of 1000 h at a starting luminance of 1000 cd/m² by a constant current driver.     

利用色彩转换法制备高色稳定性的柔性白色有机电致发光器件

本文利用色转换方法,将高效的蓝色柔性有机电致发光器件(flexible organic light emitting devices, FOLEDs)与色转换材料(color conversion material, CCM)相结合,制备了柔性白色有机电致发光器件(white organic light emitting devices, WOLEDs).首先利用2, 3, 5, 6-Tetrafluoro-7, 7, 8, 8-tetracyano-quinodimethane (F4-TCNQ)和4, 4', 4"-tris-(N-3-methylphenyl-N-phenylamino) tripheny-lamine (m-MTDATA)组成的多量子阱(multiple quantum well, MQW)结构作为空穴注入层(hole injection layer, HIL)结合新型蓝光材料N⁶, N⁶, N¹², N¹²-tetrap-tolylchrysene-6, 12-diamine (NCA)制备出高效的蓝光FOLEDs,然后将其与色转换材料4-(dicyanomethylene)-2-tert-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) 结合,通过沉积不同厚度的CCM来优化白光器件的发光光谱,获得了色稳定性较高的白光. 实验结果表明:在驱动电压为7 V, DCJTB的厚度为120 nm时得到较接近白光等能点的色坐标 (0.33, 0.27),且当驱动电压由6 V升至11 V 时,器件的色坐标变化仅为(±0.02, ±0.02), 表现出高色稳定性.     

White organic light-emitting device with\ both phosphorescent and fluorescent emissive layers

This paper reports the fabrication of novel white organic light-emitting device（WOLED） by using a high efficiency blue fluorescent dye N-（4-（（E）-2-（6-（（E）-4-（diphenylamino）styryl）naphthalen-2-yl）vinyl）phenyl）oN- phenylbenzenamine （N-BDAVBi） and a red phosphoresecent dye bis （1-（phenyl） isoquinoline） iridium （III） acetylanetonate （Ir（piq）2（acac））. The configuration of the device was ITO/PVK：TPD/CBP： N-BDAVBi /CBP/ BALq： Ir（piq）2（acac）/BCP/Alq3/LiF：AL. By adjusting the proportion of the dopants （N-BDAVBi, Ir（piq）2（acac）） in the light-emitting layer, white light with Commission Internationale de l＇Eclairage （CIE） coordinates of （0.35, 0.35） and a maximum luminance of 25350cd/m2 were obtained external quantum and current efficiency of 6.78% and between the two light-emitting layers and using BCP at an applied voltage of 22V. The WOLED exhibits maximum 12cd/A respectively. By placing an undoped spacer CBP layer as hole blocking layer, the colour stabilization slightly changed when the driving voltage increased from 6 to 22 V.     

Highly efficient bipolar connecting layers for tandem organic light-emitting devices

A highly efficient tandem organic light-emitting device (OLED) has been fabricated by using an effective bipolar connecting layer structure. The connecting layers were made up of a layer of magnesium (Mg): 2,7-dipyrenyl-9,9-diphenyl fluorene (N-DPF) and a layer of tungsten trioxide (WO₃). Such a connecting layer structure permits efficient opposite holes and electrons flowing into two adjacent emitting units. The current efficiency of the two-unit tandem device can be dramatically enhanced by more than four times compared with that of the conventional single-unit device. At 60 mA/cm², the current efficiency of the tandem OLED using the connecting layers of Mg: N-DPF/WO₃ was about 8.15 cd/A. The results can be marked as a breakthrough approach to improve the current efficiency and brightness of OLEDs. Furthermore, a model of the carrier tunneling into light-emitting units is proposed based on carrier balance and field-assisted tunneling. It indicates that the connecting layer structure functions as the origin of high efficiency for the tandem OLEDs.     

Highly flexible and efficient top-emitting organic light-emitting devices with ultrasmooth Ag anode

We demonstrate highly flexible and efficient top-emitting organic light-emitting devices (TOLEDs) by using an ultrasmooth Ag anode. A template-stripping process has been employed to create the ultrasmooth Ag anode on a photopolymer substrate. The flexible TOLEDs obtained by this method keep good electroluminescence properties under a small bending radius and after repeated bending. The efficiency of the flexible TOLEDs is improved by 60% compared with the conventional TOLEDs deposited on Si substrate due to the enhanced hole injection from the ultrasmooth anode.     

Electroplex emission at PVK/Bphen interface for application in white organic light-emitting diodes

White organic light-emitting diode (WOLED) with a structure of ITO/poly(N-vinylcarbazole) (PVK)/4,7-diphenyl-1, 10-phenanthroline (Bphen)/tris(8-hydroxyquinoline)aluminum (Alq₃)/LiF/Al has been fabricated via the thermal evaporation technique. The electroluminescence (EL) spectrum of the as-fabricated WOLED covers from 380 to 700 nm of the visible light region with a wide blue emission from PVK and an interesting new red emission. The red emission at 613 nm in EL spectra of the WOLED was attributed to electroplex emission at PVK/Bphen interface since it was not observed in photoluminescence spectra. The WOLED showed a Commission International De l'Eclairage coordinate of (0.31, 0.32), which is very close to the standard white coordinate (0.33, 0.33).     

Negative capacitance in doped bi-layer organic light-emitting devices

This paper reports that the doped bi-layer organic light-emitting devices are fabricated by doping in different regions of the light-emitting layer,the admittance and luminance spectra to characterize the capacitance and luminance of the device are measured.Negative capacitance (NC) appeared at low frequencies when the doped devices are biased with high voltages.The measured phase difference between AC voltage applied across the device and AC current flowing through the device show that the device is inductive when NC appears.     

Efficient fluorescent white organic light-emitting devices with a reduced efficiency roll-off based on a blue ambipolar fluorescent emitter

White organic light-emitting devices (WOLEDs) with fluorescent donor-acceptor-substituted spirobifluorene compounds (red 2-diphenylamino-7-(2,2-dicyanovinyl)-9,9′-spirobifluorene and blue 2-diphenylamino-7-(2,2-diphenylvinyl)-9,9′-spirobifluorene) have been fabricated. The optimized WOLEDs shows a maximum current efficiency 5.9 cd/A and very low efficiency roll-off. From the brightness at maximum current efficiency to high brightness of 10000 cd/m², the current efficiency roll-off is only 0.4%. It can be attributed to the ambipolar blue fluorescent emitter with voltage-independnet mobility which makes the device having a broader charge recombination zone and balance of carrier transport.