Poly(lactic acid)-based biocomposites reinforced with modified cellulose nanocrystals

This work investigates reinforcing poly(lactic acid) (PLA) nanocomposites using triazine derivative-grafted cellulose nanocrystals (CNCs). A hydrophobic triazine derivative was synthesized and applied to modify CNCs to improve their thermal stability and diminish the hydrophilicity of the nanoparticles. CNCs before and after modification were used to reinforce PLA nanocomposites by a hot compression process. The results of thermogravimetric analysis indicated that the initial thermal decomposition temperature of modified nanocrystals was improved by approximately 100 °C compared to the original CNCs. That is, the thermal stability of modified cellulose nanocrystals was improved due to the shielding effect of CNCs by a hydrophobic aliphatic amine layer on the surface of the nanoparticles. The results of dynamic contact angle measurements revealed a decrease of hydrophilicity of the modified CNCs. The results from scanning electron microscopy and a UV–Vis spectrophotometer revealed that the compatibility between the modified nanocrystals and the PLA was improved. Finally, the results of tensile tests indicated a significant improvement in terms of breaking strength and elongation at the break point.     

Cellulosic nanocomposite membranes from hydroxypropyl cellulose reinforced by cellulose nanocrystals

Cellulosic nanocomposite membranes were prepared by incorporation of cellulose nanocrystals (CNCs) into a hydroxypropyl cellulose (HPC) matrix using a mixing/evaporation technique. CNCs were obtained from filter paper using the sulfuric acid hydrolysis method with the aid of ultrasonication. The relationship between the microstructure and mechanical properties of the CNCs/HPC nanocomposite membranes was studied. Scanning electron microscopy showed that the CNCs were well dispersed in the HPC matrix, and the fracture surface demonstrated a fibrous characteristic. With increasing CNCs content, the tensile strength and Young’s modulus of the CNCs/HPC nanocomposite membranes gradually increased. At 5 wt% content of CNCs, the strength was increased by 525 % and the Young’s modulus by 124 % compared with pure HPC membrane. Moreover, the effect of the phase change of HPC on the mechanical properties of the CNCs_5wt%/HPC nanocomposite membranes and the corresponding mechanism were also studied.     

Melt‐blending of unmodified and modified cellulose nanocrystals with reduced graphene oxide into PLA matrix for biomedical application

In this article, we successfully fabricated the bionanocomposites using cellulose nanocrystals (CNCs) and reduced graphene oxide (rGO) reinforced into biodegradable polylactic acid (PLA) matrix through melt‐mixing method. Due to the affinity difference between hydrophilic CNC and hydrophobic PLA, the surface modification of CNC was employed using quaternary ammonium salts (CTAB) as a surfactant. The nanocomposites were developed using different blend ratios of CNC/modified CNC (1, 2, and 3) wt% and (0.5 wt%) rGO into the polymer matrix. The morphology of CNC, q‐CNC (modified CNC), and nanocomposites were inspected by atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). It is demonstrated from tensile tests that, the nanocomposite with 1 wt% CNC and rGO showed maximum tensile strength compared with PLA and its nanocomposites. Moreover, the nanocomposite with 1 wt% CNC and rGO was also having maximum thermal stability. From cytotoxicity evaluation, it is observed that all the nanocomposites are nontoxic and cytocompatible to HEK293 cells. In addition to this, the nanocomposite with q‐CNC showed enhanced barrier properties compared with PLA and PLA/CNC/rGO nanocomposite. The results obtained from different characterizations showed that the incorporation of surfactant onto CNC improved the dispersion in PLA but at the same time deteriorated the PLA matrix.     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Development of biopolymer/cellulose/silica nanostructured hybrid materials and their characterization by NMR relaxometry

The objective of this study was to investigate the preparation and properties of hybrid materials composed of poly(lactic acid) (PLA) and poly(lactic acid)/poly(lactic-co-glycolic acid) (PLA/PLGA) blends employing cellulose nanocrystals (CNCs) and/or organophilic silica (R972) as nanoparticles. The CNCs were obtained by acid hydrolysis of commercially available microcrystalline cellulose (MCC). The materials were produced in film form by solution casting. Organophilic silica was incorporated at a ratio of 3 wt.%, and CNCs were added at ratios of 3 wt.% and 5 wt.% in relation to the weight of the polymer matrix. Two series of films were obtained. The first was prepared using only PLA as the matrix, and the second was obtained using blends of PLA and PLGA. The properties of the films were evaluated by X-ray diffractometry, nuclear magnetic resonance, Fourier-transform infrared spectroscopy and measurement of mechanical properties. The results revealed that each nanoparticle, whether added individually or combined with the other type of nanoparticle, induced different final material properties. Cellulose nanocrystals can act as nucleating agents for the crystallization of PLA. There was an improvement in the mechanical performance of films with the addition of CNCs. Further, the incorporation of silica combined with CNCs resulted in the generation of films with the strongest mechanical properties. The results of this study indicate that silica decreases the surface tension between PLA-cellulose and PLA/PLGA-cellulose.     

Mechanical and flame‐retardant properties of biodegradable polylactide composites with hyperbranched silicon‐containing polymer

A hyperbranched polymer (HBP‐B2) containing siloxane chains was synthesized via bulk polymerization of diepoxide with a primary amine in the presence of monoepoxide. The weight‐average molecular weight of the prepared polymers was approximately 9200. Composites of polylactide (PLA) with aluminum trihydroxide (ATH) and the HBP‐B2 were prepared via direct melt compounding using a brabender. The test results showed that the LOI could be raised to 34% for the PLA composite with 25 wt% ATH and 5% HBP‐B2. The surface thermal profile of the composite during UL94 V test was further captured by an infrared camera, which was helpful to understand the flame‐retardant properties of the different samples. A V‐0 rating could be achieved by adding ATH and HBP‐B2 to the PLA matrix. Incorporation of HBP‐B2 as a plasticizer could increase the impact strength of a PLA blend or composite. For example, an addition of 10 wt% of HBP and 20 wt% ATH increased the elongation at break from 5% for neat PLA to 155% for the PLA composite.     

Interplay of colloidal stability of cellulose nanocrystals and their dispersibility in cellulose acetate butyrate matrix

Cellulose nanocrystals (CNC) prepared from eucalyptus cellulose CNCs were modified by the reaction with methyl adipoyl chloride, CNCm, or with a mixture of acetic and sulfuric acid, CNCa. The CNC were either dispersed at 0.1 wt% in the pure solvents ethyl acetate (EA), tetrahydrofuran (THF) and dimethylformamide (DMF) or in cellulose acetate butyrate (CAB) solutions prepared in these solvents at 0.9 wt%. The colloidal behavior of these dispersions was systematically investigated using a phase separation analyzer LUMiReader^®. The mechanical properties and morphological features of the films resulting from the mixtures of CAB and CNC were determined by dynamic mechanical analysis, optical microscopy and atomic force microscopy, respectively. Regardless the functional group attached to the surface of CNC, the best colloidal stability was observed for dispersions prepared in CAB/DMF solution. Higher degree of substitution of modified CNCs favored the colloidal stability in EA and THF. Composite films prepared from CAB/DMF solutions were more homogeneous and presented better mechanical performance than those prepared in CAB/EA or CAB/THF. The mechanical performance of composites and neat CAB prepared from DMF was CAB/CNCs > CAB/CNCm > CAB/CNCa > CAB, indicating that the modification weakens the percolation process, which is mediated by H bonding.     

Thermo-mechanical properties of microfibrillated cellulose-reinforced partially crystallized PLA composites

Polylactic acid (PLA) in a crystallized state has mechanical properties at high temperatures superior to PLA in an amorphous state. However, a long annealing time is required to fully crystallize PLA. In this study, microfibrillated cellulose (MFC)-reinforced partially crystallized PLA composites were produced, with the goal of reducing the time required to fabricate PLA parts. A series of PLA/MFC composites at a fiber content of 10 wt% from degree of crystallinity (Xc) 0 to 43% was obtained by annealing at 80 °C. Although the annealing time required to obtain a composite (Xc: 17%) was only around one-seventh of the 20 min needed to fully crystallize neat PLA (Xc: 41%), both materials had comparable rigidity above the glass transition temperature (T _g) and creep deformation at around T _g. These results showed that partially crystallized PLA/MFC composite can replace fully crystallized neat PLA.     

Thermally-activated shape memory behaviour of bionanocomposites reinforced with cellulose nanocrystals

Bionanocomposites with thermally-activated shape memory ability have been designed based on a synthesized poly(ester-urethane) matrix reinforced with both neat and functionalized cellulose nanocrystals. The functionalization of the cellulose nanocrystals was performed by grafting poly(l-lactic acid) (PLLA) chains onto their surface. The matrix has a block copolymer structure of two biodegradable and biocompatible polymers, poly(ε-caprolactone) (PCL) and PLLA. This research is focused on the effects of cellulose nanofillers on the thermally-activated shape memory response of the neat matrix confirming that the bionanocomposites are able to show shape memory effects at 35 °C, close to the human body temperature, making these materials good candidates for biomedical applications. Three thermo-mechanical cycles at 50 % of deformation were performed in order to check the thermally-activated shape memory ability of the bionanocomposites and to determine the shape memory parameters, namely the strain fixity (R_f), and the strain recovery (R_r) ratio. Both bionanocomposites, with neat and functionalized cellulose nanocrystals, present excellent shape memory behaviour maintaining the recovery behaviour at values of about 90 % as measured previously for the pure matrix, indicating that the addition of the nanofiller maintains the good ability to recover the initial shape of the matrix. The cellulose nanofillers clearly improve the ability of the polymer to fix the temporary shape. In fact, the bionanocomposites show R_f at about 90 %. Moreover, bionanocomposites reinforced with the functionalized cellulose nanocrystals maintain constant their performance during all the thermo-mechanical cycles thus confirming that the improvement in the shape memory behaviour can be mainly attributed to the increase of the interactions between the functionalized cellulose nanocrystals with the polymeric matrix.     

High performance poly (vinyl alcohol)/cellulose nanocrystals nanocomposites manufactured by injection molding

Polyvinyl alcohol (PVA)/cellulose nanocrystals (CNCs) compounds were successfully melt-processed by injection molding. During the processing, water was involved in the system as both the dispersion medium for CNCs and the plasticizer for PVA. Meanwhile, formamide was added to prevent the evaporation of water and to co-plasticize PVA. Thermal gravimetric analysis and differential scanning calorimetry indicated the melt processing window of PVA was expanded by 40 °C. Tensile tests showed that the mechanical properties of injection-molded samples were significantly improved with the addition of CNCs. The tensile strength of the composites increased from 32 to 58 MPa, and modulus increased from 175 to 1,252 MPa when 7 wt% CNCs was added. Moreover, the volume shrinkage of PVA nanocomposites upon drying as well as their water leaching rate could be remarkably reduced in the presence of CNCs.     

Organic‐montmorillonite modified shape memory epoxy composite

A series of organic‐montmorillonite (OMMT) modified shape memory epoxy (SMEP) composites were prepared for the purpose of application on space deployable structures. Tensile test, dynamic mechanical analysis (DMA), X‐ray diffraction (XRD), scanning electron microscope (SEM), and fold‐deploy shape memory test methods were used to characterize the mechanical, structure, and shape memory properties of these materials. The results showed addition of OMMT could improve the composites' toughness, tensile strength, transition temperature, and shape recovery speed, while shape recovery ratio was unaffected. Composite with 3wt%. OMMT had the optimum combination property. It could fully recover its original shape in about 2 min at 185°C under the maximum bending angle of 180°. Its elongation at break and tensile strength were increased by 835 and 17.4%, respectively, compared to that of neat SMEP. The transition temperature also slightly increased. Copyright © 2010 John Wiley & Sons, Ltd.     

Insight into the extraction and characterization of cellulose nanocrystals from date pits

This study aims to extract and characterize cellulose nanocrystals (CNCs) from date pits (DP), an agricultural solid waste. Two methods were used and optimized for the cellulose nanocrystals (CNCs) extraction, namely the mechanical stirrer method (CNCs₁) and the Soxhlet apparatus method (CNCs₂) in terms of chemical used, cost, and energy consumption. The results showed that scanning electron microscopy revealed the difference in the morphology as they exhibit rough surfaces with irregular morphologies due to the strong chemical treatments during the delignification and bleaching process. Moreover, transmission electron microscopy analysis for CNCs reveals the true modification that was made through sulfuric acid hydrolysis as it presents cellulose microfibrils with a packed structure. Fourier transform infrared proved that the CNCs were successfully extracted using the two methods since most of the lignin and hemicellulose components were removed. The crystallinity index of CNCs₁ and CNCs₂ was 69.99%, and 67.79%, respectively, and both presented a high yield of CNCs (≥10%). Ultimately, both techniques were successful at extracting CNCs. Based on their cost-effectiveness and time consumption, it was concluded that method 1 was less expensive than method 2 based on the breakdown of the cost of each step for CNCs production.     

The synergetic effect of phenylphosphonic acid zinc and microfibrillated cellulose on the injection molding cycle time of PLA composites

This study evaluates the effects of nucleants phenylphosphonic acid zinc (PPA-Zn) and talc, mold temperature, and microfibrillated cellulose (MFC) reinforcement in the acceleration of injection molding cycle of polylactic acid (PLA). PLA was dissolved in an organic solvent, mixed with nucleant and MFC, and dried compounds were injection molded into molds at temperatures ranging from 40 °C to 95 °C and holding times from 10 s to 120 s. Our results showed that PPA-Zn is more effective nucleating agent compared to talc. The addition of 1 wt% PPA-Zn and the mold temperature of 95 °C exhibited the fastest crystallization rates for the molded PLA, however, at this temperature the parts could not be quickly ejected without distortion. Addition of 10 wt% MFC increased the stiffness of PLA at high temperatures and allowed ejection of parts without distortion at a holding time of just 10 s. At this holding time, the crystallinity of the PLA composite was 15.3% but the storage modulus above T _g was superior to that of fully crystallized neat PLA due to MFC reinforcement, retaining the shape of the molded part during demolding. The mechanical properties of the composite at room temperature were also higher than those of fully crystallized neat PLA.     

Improved mechanical properties of epoxy‐based composites with hyperbranched polymer grafting glass‐fiber

A glass‐fiber, grafted by hyperbranched polymer with hydroxyl group (GF‐HBPH), reinforced epoxy‐based composite was evaluated for mechanical properties and compared with the neat epoxy and silanized glass‐fiber, GF‐APS. The epoxy/GF‐HBPH composites were studied by attenuated total internal reflectance infrared spectroscopy, ¹H nuclear magnetic resonance spectroscopy, thermal gravimetric analysis, mechanical properties analysis, and field emission‐scanning electron microscopy. The results showed that the incorporation of GF‐HBPH could simultaneously enhance the mechanical properties of the epoxy composites. Field emission‐scanning electron microscopy images of the fracture surfaces of the test specimens were used to support the results and conclusions. Copyright © 2016 John Wiley & Sons, Ltd.     

Self‐Healing Polyester Urethane Supramolecular Elastomers Reinforced with Cellulose Nanocrystals for Biomedical Applications

Stretchable self‐healing urethane‐based biomaterials have always been crucial for biomedical applications; however, the strength is the main constraint of utilization of these healable materials. Here, a series of novel, healable, elastomeric, supramolecular polyester urethane nanocomposites of poly(1,8‐octanediol citrate) and hexamethylene diisocyanate reinforced with cellulose nanocrystals (CNCs) are introduced. Nanocomposites with various amounts of CNCs from 10 to 50 wt% are prepared using solvent casting technique followed by the evaluation of their microstructural features, mechanical properties, healability, and biocompatibility. The synthesized nanocomposites indicate significantly higher tensile modulus (approximately 36–500‐fold) in comparison to the supramolecular polymer alone. Upon exposure to heat, the materials can reheal, but nevertheless when the amount of CNC is greater than 10 wt%, the self‐healing ability of nanocomposites is deteriorated. These materials are capable of rebonding ruptured parts and fully restoring their mechanical properties. In vitro cytotoxicity test of the nanocomposites using human dermal fibroblasts confirms their good cytocompatibility. The optimized structure, self‐healing attributes, and noncytotoxicity make these nanocomposites highly promising for tissue engineering and other biomedical applications.     

On the use of plant cellulose nanowhiskers to enhance the barrier properties of polylactic acid

Polylactic acid (PLA) nanocomposites were prepared using cellulose nanowhiskers (CNW) as a reinforcing element in order to asses the value of this filler to reduce the gas and vapour permeability of the biopolyester matrix. The nanocomposites were prepared by incorporating 1, 2, 3 and 5 wt% of the CNW into the PLA matrix by a chloroform solution casting method. The morphology, thermal and mechanical behaviour and permeability of the films were investigated. The CNW prepared by acid hydrolysis of highly purified alpha cellulose microfibers, resulted in nanofibers of 60–160 nm in length and of 10–20 nm in thickness. The results indicated that the nanofiller was well dispersed in the PLA matrix, did not impair the thermal stability of this but induced the formation of some crystallinity, most likely transcrystallinity. CNW prepared by freeze drying exhibited in the nanocomposites better morphology and properties than their solvent exchanged counterparts. Interestingly, the water permeability of nanocomposites of PLA decreased with the addition of CNW prepared by freeze drying by up to 82% and the oxygen permeability by up to 90%. Optimum barrier enhancement was found for composites containing loadings of CNW below 3 wt%. Typical modelling of barrier and mechanical properties failed to describe the behaviour of the composites and appropriate discussion regarding this aspect was also carried out. From the results, CNW exhibit novel significant potential in coatings, membranes and food agrobased packaging applications.     

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Nanogenerators, as the typical conversion of mechanical energy to electrical energy devices, have great potential in the application of providing sustainable energy sources for powering miniature devices. In this work, cellulose acetate/cellulose nanocrystal(CA/CNC) composite nanofiber membranes were prepared by electrospinning method and then utilized to manufacture a flexible pressure-driven nanogenerator. The addition of CNC not only increased the content of piezoelectric cellulose I crystallization but also strengthened the mechanical deformation of the nanofiber membranes, which could greatly enhance the piezoelectric performance of CA/CNC composite membranes. The CA/CNC composite nanofiber membrane with 20%(mass fraction) of CNC(CA/CNC-20%) showed optimal piezoelectric conversion performance with the output voltage of 1.2 V under the force of 5 N(frequency of 2 Hz). Furthermore, the output voltage of the CA/CNC-20% nanogenerator device exhibited a linear relationship with applied impact force, indicating the great potential in pressure sensors.     

PLA Electrospun Fibers Reinforced with Organic and Inorganic Nanoparticles: A Comparative Study

In this work, different poly (lactic acid) (PLA)-based nanocomposite electrospun fibers, reinforced with both organic and inorganic nanoparticles, were obtained. As organic fibers, cellulose nanocrystals, CNC, both neat and functionalized by “grafting from” reaction, chitosan and graphene were used; meanwhile, hydroxyapatite and silver nanoparticles were used as inorganic fibers. All of the nanoparticles were added at 1 wt% with respect to the PLA matrix in order to be able to compare their effect. The main aim of this work was to study the morphological, thermal and mechanical properties of the different systems, looking for differences between the effects of the addition of organic or inorganic nanoparticles. No differences were found in either the glass transition temperature or the melting temperature between the different electrospun systems. However, systems reinforced with both neat and functionalized CNC exhibited an enhanced degree of crystallinity of the electrospun fibers, by up to 12.3%. From a mechanical point of view, both organic and inorganic nanoparticles exhibited a decreased elastic modulus and tensile strength in comparison to neat electrospun PLA fibers, improving their elongation at break. Furthermore, all of the organic and inorganic reinforced systems disintegrated under composting conditions after 35 days.     

The potential use of electrospun polylactic acid nanofibers as alternative reinforcements in an epoxy composite system

This pilot study elaborates the development of novel epoxy/electrospun polylactic acid (PLA) nanofiber composites at the fiber contents of 3, 5, and 10 wt % to evaluate their mechanical and thermal properties using flexural tests and differential scanning calorimetry (DSC). The flexural moduli of composites increase remarkably by 50.8 and 24.0% for 5 and 10 wt % fiber contents, respectively, relative to that of neat epoxy. Furthermore, a similar trend is also shown for corresponding flexural strengths being enhanced by 31.6 and 4.8%. Fractured surface morphology with scanning electron microscopy (SEM) confirms a full permeation of cured epoxy matrix into nanofiber structures and existence of nondestructive fibrous networks inside large void cavities. The glass transition temperature (T_g) of composites increases up to 54–60 °C due to embedded electrospun nanofibers compared to 50 °C for that of epoxy, indicating that fibrous networks may further restrict the intermolecular mobility of matrix in thermal effects. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 618–623     

Preparation and property assessment of neat lignocellulose nanofibrils (LCNF) and their composite films

Lignocellulose nanofibrils (LCNF) were produced from thermo-mechanical pulp (TMP) using a micro-grinder and were characterized with respect to fiber diameter and thermal stability. The initial water content in the TMP affected the defibrillation process and longer grinding time was necessary for the air-dried TMP, resulting in LCNF with higher fibril diameter. As compared to the reference cellulose nanofibrils (CNF) produced through a refining process, LCNF was less thermally stable and started to degrade at a temperature that was 30 °C lower than that of CNF. LCNF obtained from the never-dried TMP was combined with various additives (10 wt%) to produce composite films. The neat LCNF and composite films did not reach the mechanical properties of the neat CNF film that was evaluated as reference. However, the addition of poly(vinyl alcohol) (PVA) at 10 wt% on a dry basis did cause a 46 and 25% increase in tensile strength and elastic modulus, respectively. Other additives including cellulose nanocrystals, bentonite and CNF were also found to increase to some extent the Young’s modulus and ductility of the LCNF composite films whereas the addition of talc did not improve the film performance. Water absorption of neat LCNF films was lower than the reference CNF and was negatively affected by the addition of PVA.