Adjusting the selectivity of inorganic anion separation by capillary electrophoresis

The separation of the principal inorganic anions (bromide, carbonate, chlorate, chloride, fluoride, nitrate, nitrite, sulfate, phosphate) has been achieved using a capillary electrophoresis system with indirect UV detection at 260 nm. Several types of cationic surfactants (quaternary ammonium, phosphonium or methonium) were tested as electroosmotic flow modifiers and added to a chromatebased buffer prepared from potassium dichromate. The influence of many physicochemical parameters such as nature and concentration of cationic surfactant, buffer pH, dichromate concentration buffer, voltage and temperature upon the migration time of an analyte anion, peak efficiency, asymmetry factor, and finally resolution has been investigated. A linear relationship between the corrected area and the anion concentration in the 2.5–50 ppm range was obtained, thus allowing the quantitative analysis of anions in mineral water. Finally, by increasing the hydrodynamic injection time, the separation of inorganic anions at a low concentration level of 50 ng/ml was achieved without any loss of resolution.     

Combinatorial enantiomeric separation of diverse compounds using capillary array electrophoresis

Combinatorial chiral separations were performed on a 96-capillary array electrophoresis system. A comprehensive enantioseparation protocol employing neutral and sulfated cyclodextrins as chiral selectors for common basic, neutral and acidic compounds was developed. By using only four judiciously chosen separation buffers, successful enantioseparations were achieved for 49 out of 54 test compounds spanning a large variety of pK and structures. Therefore, unknown compounds can be screened in this manner to identify the optimal enantioselective conditions in just one run.     

Chiral separations of transition metal complexes using capillary zone electrophoresis.

Several buffer additives that may facilitate chiral separation for optically active transition metal (TM) systems are investigated using capillary zone electrophoresis. The TM complexes evaluated exhibit considerable heterogeneity with respect to total complex charge (0 to 4+), ligand type, and identity of the central metal including Ru2+, Ni2+, Cr3+, and Co3+, threo-D[+]-Isocitrate, potassium antimonyl-d-tartrate and dibenzoyl-L-tartrate are identified as the most efficient chiral selectors. Interestingly, TM complexes exhibiting a (3+) total complex charge exhibit a reversal of enantiomer elution order versus all other complexes when separated using the tartrate additives. Operating parameters including pH, temperature, and capillary length are discussed, and chiral separations of complex mixtures are demonstrated.     

毛细管电泳在手性化合物分离分析中的研究进展

手性化合物的对映异构体往往表现出不同的生理活性,因此建立手性化合物的有效分离分析方法具有重要意义。毛细管电泳(CE)是一种分离效率高、分析速度快、样品用量少、分离模式灵活多样的分离分析方法,在手性化合物的分离和检测领域应用广泛。该文主要综述了2017～2019年CE在手性分离分析方面的最新进展,并对其未来的发展趋势进行了展望。     

On-column complexation of metal ions using 2,6-pyridinedicarboxylic acid and separation of their anionic complexes by capillary electrophoresis with direct UV detection

On-column complexation of metal ions with 2,6-pyridinedicarboxylate (2,6-PDC) to form anionic complexes enabled their separation by capillary zone electrophoresis with direct UV detection at 214 nm. Nine metal ions, Cu2+, Zn2+, Ni2+, Cd2+ Mn2+, Pb2+, Fe3+, Al3+ and Ca2+, were determined in less than 7 min using 10 mM 2.6-PDC solution containing 0.75 mM tetradecyltrimethylammonium bromide at pH 4.0. Satisfactory working ranges (20-300 microM), detection limits (3-10 microM) and good repeatability of the peak areas (RSD 2.1-4.2%, n=5) were obtained using hydrodynamic injection (30 s). The proposed method was used successfully for the determination of Mn2+, Fe3+, Al3+ and Ca2+ in groundwaters.     

Nonaqueous media for separation of nonionic organic compounds by capillary electrophoresis

For the separation of neutral compounds by micellar electrokinetic chromatography, separations are usually carried out in predominantly aqueous solution in order to preserve the charged micelle necessary for the separation. We now show that polycyclic aromatic hydrocarbon (PAH) compounds can be separated efficiently by capillary electrophoresis in pure methanol or in aqueous-organic mixtures containing a high percentage of methanol. Sodium tetradecyl sulfate was the preferred surfactant. The effects of pH, solvent composition, surfactant structure, and surfactant concentration on the separations were studied. Reproducible migration times and linear calibration plots were obtained.     

Enantiomer separation by capillary electrophoresis using DEAE-dextran and aminoglycosidic antibiotics

Summary Diethylaminoethyl (DEAE) dextran hydrochloride and three kinds of aminoglycosidic antibiotics; fradiomycin sulfate, kanamycin sulfate and streptomycin sulfate, were employed as chiral selectors in capillary electrophoresis, enantiomer separation. These selectors are cationic or basic because of amino functionality and therefore used for enantiomer separation of acidic compounds. To avoid adsorption of the basic or cationic selectors on the capillary inner surface, a coated capillary was employed. Among those tested, enantiomers of binaphthyl compounds and synthetic intermediates of diltiazem analogues were separated. Methanol addition was effective for the improvement of peak shape and resolution.     

Manipulation of separation selectivity in capillary zone electrophoresis of anionic solutes

This article discusses the main approaches to the manipulation of the separation selectivity of inorganic and low-molecular-mass anions in capillary zone electrophoresis (CZE). Physical or instrumental effects such as the detection mode, the sampling mode, the separation voltage, and the temperature are easy to control but their influence on selectivity is generally minimal, except for the use of selective detection. Selectivity effects arising from chemical parameters (i.e. effective size and charge, and structure of analyte; the pH, surfactant type and content, polyelectrolyte content, organic solvent content of the electrolyte; capillary treatment; and complexing agents) are much more significant than those resulting from physical effects. The effects on separation selectivity exerted by some of the above parameters can be complex, so that manipulation of selectivity in CZE of anionic solutes is often difficult. Nonetheless, many practical applications can be performed through the judicious control of parameters noted in this review. Some practical limitations to selectivity manipulation are highlighted and possible areas that can be studied in the future for selectivity control are noted.     

Reaction of the low-valent transition metal complexes with non-transition organometallic compounds

The zero-valent triphenylphosphine complexes of palladium and platinum were found to react readily under mild conditions with organomercurials RHgX and R₂Hg. Final products appear to be σ-bonded organic derivatives of Pd and Pt. In several cazses, the relatively stable intermediates with platinum to mercury bond were isolated. Dibenzylideneacetone-palladium (0) and -platinum(0) complexes exhibits similar reactivity towards organomercurials.     

Chiral separation in capillary electrophoresis using dual neutral cyclodextrins: theoretical models of electrophoretic mobility difference and separation selectivity

Simple equations and theoretical models, related to enantioselectivity (kappa) and C, have been developed for prediction of electrophoretic mobility difference (Deltamu) and separation selectivity (alpha) for enantiomers in CE using dual CDs, where alpha and kappa are defined as the ratio of mu and the ratio of binding constant (K) for enantiomers to each CD, respectively, C the CD concentration, and the average K for enantiomers and each CD. Experiments were carried out using dual CDs as beta-CD and dimethyl-beta-cyclodextrin (DM-beta-CD) and test analytes as five pairs of amphetamine drug enantiomers. A change in observed Deltamu and alpha of enantiomers in dual CDs was found to be in excellent agreement with the theoretical models. For example, in comparison with single CD1, dual CDs can enhance Deltamu and alpha up to the maximum value when enantiomers migrate with the same order in CD1 and CD2, and have the value of rho > 1.0, where rho is the enantioselectivity ratio for CD2 to CD1, while worse Deltamu and alpha are obtained for enantiomers with rho < 1.0.     

Enantiomeric separation of acidic compounds using single-isomer amino cyclodextrin derivatives in nonaqueous capillary electrophoresis

The enantiomeric separation of a series of acidic pharmaceuticals (mostly nonsteroidal anti-inflammatory drugs) has been investigated in NACE systems using single-isomer amino beta-CD derivatives. The first part of this study consisted of the selection of the basic experimental conditions to separate efficiently the enantiomers of acidic drugs. Several parameters, such as the nature of the ionic BGE components, were studied and a methanolic solution of ammonium acetate containing the cationic CD was selected as BGE. A D-optimal design with 20 experimental points was then applied and the nature and concentration of the CD were found to have a significant effect on the enantiomeric resolution for all studied compounds. Resolution (R(s)) values were always higher with 6-monodeoxy-6-mono(3-hydroxy)propylamino-beta-CD (PA-beta-CD) compared to those obtained with 6-monodeoxy-6-mono(2-hydroxy)propylamino-beta-CD (IPA-beta-CD). However, the latter led to shorter migration times. Generic NACE conditions were then selected by means of the multivariate approach in order to obtain the highest R(s) values in a minimum amount of time. Finally, dependence of separation selectivity, resolution, as well as mobility difference on chiral selector concentration was discussed and binding constants with PA-beta-CD were estimated for the two enantiomers of one of the model compounds, suprofen in these NACE systems.     

Chiral separation of four fluoroquinolone compounds using capillary electrophoresis with hydroxypropyl-beta-cyclodextrin as chiral selector

A capillary zone electrophoresis (CZE) investigation on the enantiomeric separation of lomefloxacin, gatifloxacin, pazufloxacin and ofloxacin was undertaken. Resolution of the enantiomers was achieved using hydroxypropyl-beta-cyclodextrin (HP-beta-CD) as the chiral selector. Parameters influencing separation include cyclodextrin concentration, separational potential, pH and organic additive are discussed. A buffer consisting of 70 mM phosphate and 40 mM HP-beta-CD at pH 3.96 was found to be highly efficient for the separation of lomefloxacin, at pH 3.90 for gatifloxacin, at pH 5.04 for pazufloxacin and at pH 2.16 for ofloxacin. To the best of our knowledge, this is the first report on the enantiomeric resolution of lomefloxacin and gatifloxacin applying CE.     

The role of organic solvents in the separation of nonionic compounds by capillary electrophoresis

Although nonionic compounds can be separated by micellar electrokinetic chromatography (MEKC), application of this technique is restricted by a somewhat limited elution range. Incorporation of organic solvents in the background electrolyte (BGE) greatly extends the scope of MEKC and provides a major variable in optimizing the separation of neutral analytes. This paper provides a systematic review of the principles and scope of the separation of neutral analytes by capillary electrophoresis (CE) in organic-aqueous solution. The methods surveyed include those that use tetraalkylammonium salts, dioctyl sulfosuccinate, lauryl poly(oxyethylene) sulfate. Polyaromatic hydrocarbon (PAH) compounds can be separated using sodium hexadecyl sulfate in 70% methanol (30% aqueous) to 100% methanol.     

On-line enhancement and separation of nanoparticles using capillary electrophoresis

We describe a rapid, simple, and highly efficient capillary electrophoresis (CE)-based method for the analysis of nanoparticles (NPs). In this study, we used the reversed electrode polarity stacking mode (REPSM) of CE to assess the feasibility of enhancing the detection of Au NPs and Au/Ag NPs, optimizing parameters such as the length of time for which the REPSM was applied, the concentrations of the buffer and the sodium dodecylsulfate (SDS) surfactant, and the pH. Under the optimized on-line enhancement conditions [buffer: SDS (40 mM) and 3-cyclohexylamino-1-propanesulfonic acid (CAPS; 10 mM) at pH 10.0; applied voltage: 20 kV; REPSM applied for 24s], the detection limits of the Au NPs and Au/Ag NPs increased by ca. 30- and 140-fold, respectively. In addition, when the NPs were subjected to on-line enhancement and separation by CE using diode array detection (DAD), this approach allowed chemical characterization of the NP species. Our results suggest that such CE analyses will be useful for accelerating the rates of fabrication and characterization of future nanomaterials.     

Altering the selectivity of inorganic anion separations using electrostatic capillary electrophoresis

A new method for altering the selectivity of inorganic anion separations in capillary electrophoresis is described. Addition of the zwitterionic surfactant 3-(N,N-dimethyldodecylammonio)propane sulfonate (DDAPS) to the background electrolyte modifies the migration order via electrostatic ion chromatography type interactions. Variation of the DDAPS surfactant concentration from 4 to 120 mM monotonically alters the selectivity from electrophoretic mobility based to that of electrostatic ion chromatography, without increasing Joule heating. This technique was applied to the determination of nitrate, nitrite, bromide and iodide in artificial seawater. Detection limits for the anions in 1:5 diluted seawater were 11, 5, 7 and 11 microM, respectively.     

Enantiomeric separation of synthetic 2,3-dihydroxy-3-phenylpropionate compounds by beta-cyclodextrin-modified capillary electrophoresis

A new capillary electrophoretic method was developed for enantiomeric separation and optical impurity analysis of three synthetic 2,3-dihydroxy-3-phenylpropionate compounds using native beta-cyclodextrin (beta-CD) as chiral selector and borate as a background electrolyte. The separation was carried out in uncoated capillary (58.5 cm x 75 microm I.D., effective length 48.5 cm). The results showed that beta-CD as the chiral selector exhibited good enantioselectivity and the baseline separation was obtained at pH 9.8, 200 mM borate buffer containing 1.7% beta-CD at applied voltage 15 kV and capillary temperature 20 degrees C within 15 min. The precision of each tested compound was less than 1.0% at migration time and 5.0% in corrected peak area and the accuracy of the method was in the range of 98.7-105%. Furthermore, the developed method was successfully applied to the determination of the undesirable trace (2S,3R)-(+)-form impurity in the synthetic (2R,3S)-(-)-2,3-dihydroxy-3-phenylpropionate samples.     

Chiral separation of cetirizine by capillary electrophoresis

Chiral separation of cetirizine, a second-generation H(1)-antagonist, was studied by CD-mediated CE. Several parameters, including pH, CD type, buffer concentration, type of co-ion, applied voltage and temperature, were investigated. The best conditions for chiral separation were obtained using a 75 mM triethanolamine-phosphate buffer (pH 2.5) containing 0.4 mg/mL heptakis(2,3-diacetyl-6-sulfato)-beta-CD and 10% ACN. Online UV detection was performed at 214 nm, a voltage of 20 kV was applied and the capillary was temperature controlled at 25 degrees C by liquid cooling. Hydrodynamic injection was performed for 1 s. The method was validated for the quantification of levocetirizine in tablets and for enantiomeric purity testing of the drug substance. Selectivity, linearity, LOD and LOQ, precision and accuracy were evaluated for both methods. The amount of levocetirizine dihydrochloride in the commercially available tablets was quantified and was found to be within the specification limits of the claimed amount (5 mg). The amount of distomer in levocetirizine drug substance was found to be 0.87 +/- 0.09% w/w, which is in agreement with the certificate of analysis supplied by the company.     

毛细管电泳分析中手性化合物的定性检测

毛细管电泳(CE)作为一种新型分离分析技术,具有分离效率高、分析速度快、样品用量少、分离模式灵活多样等众多优势,在手性物质分离等领域应用广泛。在以往的工作中,手性化合物的CE分离模式、手性拆分剂选择及提高分离度等研究已作了详尽报道,而成功分离后的手性物质定性、对映体出峰顺序确认等问题也至关重要。该文以CE手性化合物分离分析中是否依赖标准品分类,及其定性检测方法进行了总结。利用CE分离分析手性样品,若待测物有手性对映体标准品时,其定性通常通过比较标准品迁移时间或标准加入法完成。基于检测器的不同,依赖标准品的CE分析主要分为光学、质谱和电化学3类检测模式。其中光学检测又包含紫外-可见(UV)、激光诱导荧光(LIF)、化学发光(CL)等多种检测方式。不同的检测方式决定了样品前处理方式的差异,随之形成的谱图及手性化合物定性方式也大相径庭。当缺少手性对映体标准品时,可用的CE手性分离分析方法主要有酶消解和抗体添加法、计算法等。前两种方法主要依据对映体与特定消解酶或抗体间的相互作用,完成手性物质的选择定性,适用范围均较局限。相比较,借助理论计算,使CE结合圆二色光谱(CD)的计算法操作简单,定性准...