Photodegradation of poly(neopentyl isophthalate) part I: Laboratory and outdoor conditions

In this paper the mechanisms of photodegradation of poly(neopentyl isophthalate) (PNI) in laboratory (Suntest XXL+, λ > 300 nm) and outdoor conditions are compared. Changes in the chemical composition were studied with ATR-FTIR, SEC and MALDI-ToF MS. Furthermore, the results were compared with data presented in our previous paper on PNI coatings that were aged in the UVACUBE (λ > 254 nm). Two main aspects of photodegradation of PNI are addressed in the present paper: the influence of different wavelengths and the comparison of laboratory and outdoor exposure regarding the mechanism of degradation. Under short (λ > 254 nm) and long (λ > 300 nm) wavelength irradiation similar products of degradation are formed. However, the presence of short wavelength radiation dramatically accelerates the overall rate of photodegradation of PNI. UV light absorption calculations confirm this experimentally found acceleration. Exposure of PNI in laboratory and outdoor conditions, both with wavelengths λ > 300 nm resulted in similar degradation products in the initial stage of ageing.     

Molecular fine structure and transition dipole moment of NO2 using an external cavity quantum cascade laser

Rotational vibrational fine structure and transition dipole moment of NO₂ is measured using Doppler free saturation spectroscopy with an external grating cavity quantum cascade laser (QCL). The QCL wavelength is calibrated using a 310 cm long internally coupled Fabry–Perot interferometer. We obtain a frequency splitting of 139.68 ± 0.06 MHz (0.0047 cm⁻¹) between the spin doublets (17) of 000 → 001 transition of NO₂. The resolution of the QCL based saturation spectrometer is limited by the QCL linewidth of 3.99 MHz ( 0.00013 cm⁻¹) deduced from the half width of the Lamb dips. The Lamb dip spectroscopy is utilized to obtain a vibrational dipole moment of 0.37 Debye for the (17) transitions.     

Negatively charged micelles directed synthesis of snow-ball flower like superparamagnetic Ni nanoparticles and investigation of their properties

Snow-ball flower like Ni nanoparticles have been synthesized using negatively charged micelles. Negatively charged micelles incorporate the Ni⁺² onto its head group by electrostatic attraction and again a surfactant layer is arranged on positively charged Ni and thus in a repetitive way layer-by-layer a snow-ball flower like structure is formed. After reduction of Ni⁺² to Ni atom by sodium borohydride and hydrated hydrazine the Ni clusters (3 nm) are formed and confined in micelles in snow-ball flower like pattern. The sizes of these nanoflowers are of 30 nm order. The particles are superparamagnetic in nature with blocking temperature about 117 K.     

Isoconversional kinetics of degradation of polyvinylpyrrolidone used as a matrix for ammonium nitrate stabilization

Thermogravimetric analyzer (TGA) has been applied to measure the kinetics of the thermal degradation of virgin polyvinylpyrrolidone (PVP) and a phase stabilized PVP–ammonium nitrate (AN) material. The PVP–AN samples have been prepared by using 20 wt.% of AN and PVP of three different molecular weights. Virgin PVP undergoes a major mass loss in the region 380–550 °C leaving a small amount of nonvolatile residue. The application of an advanced isoconversional method to the respective degradation process demonstrates that its effective activation energy increases from 70 kJ mol⁻¹ to a plateau value at 250–300 kJ mol⁻¹, which is independent of the molecular weight. The PVP–AN materials lose spontaneously 20% of their mass on heating above the glass transition temperature of the PVP matrix (160–180 °C). After the escape of AN, the remaining PVP matrix degrades in the same temperature region as virgin PVP, however, the effective activation energy of this degradation is 150–200 kJ mol⁻¹.     

Enhanced tungstate electrochromism via formation of transparent conductive networks

Indium tin oxide (ITO) nanopowder was added to a polymer film containing WO₃ · H₂O particles to enhance electron conductivity and complimentary Li ion kinetics in an electrochromic device. Film conductivity increased dramatically with ITO content, suggesting the formation of conductive ITO networks in the film. The improved electron conductivity leads to a substantial increase of the effective Li⁺ ion diffusion coefficient in the composite film, from 10⁻¹¹ to 10⁻⁹ cm²/s. Electrochromic contrast studies revealed that the presence of the ITO networks leads to enhanced blue/green color contrast.     

Effects of carbon dioxide in breath gas on proton transfer reaction-mass spectrometry (PTR-MS) measurements

PTR-MS is becoming a common method for the analysis of volatile organic compounds (VOCs) in human breath. Breath gas contains substantial and, particularly for bag samples, highly variable concentrations of water vapour (up to 6.3%) and carbon dioxide (up to 6.5%). The goal of this study was to investigate the effects of carbon dioxide on PTR-MS measurements; such effects can be expected in view of the already well known effects of water vapour. Carbon dioxide caused an increase of the pressure in the PTR-MS drift tube (1% increase for 5% CO₂), and this effect was used to assess the CO₂ concentration of breath gas samples along the way with the analysis of VOCs. Carbon dioxide enhanced the concentration ratio of protonated water clusters (H₃O⁺H₂O) to protonated water (H₃O⁺) in the drift tube. Using the observed increase, being 60% for 5% CO₂, it is estimated that the mobility of water cluster ions in pure CO₂ is almost 65% lower than in air. Carbon dioxide had a significant effect on the mass spectra of the main breath gas components methanol, ethanol, 1-propanol, 2-propanol, acetone, and isoprene. Carbon dioxide caused a small increase (<10% for 5% CO₂) of the normalised main signals for the non-fragmenting molecules methanol and acetone. The increase can be much higher for the fragmenting VOCs (ethanol, propanol, and isoprene) and was, for 5% CO₂, up to 60% for ethanol. This effect of CO₂ on fragment patterns is mainly a consequence of the increased abundance of protonated water clusters, which undergo softer reactions with VOCs than the hydronium ions. Breath gas samples stored in Teflon bags lost 80% of CO₂ during 3 days, the decrease of VOC signals, however, is mainly attributed to decreasing VOC concentrations and to the loss of humidity from the bags.     

Magnetic field effect on chemical compositions of spherical Fe/Co fine particles synthesized from a gaseous mixture of iron pentacarbonyl and cobalt tricarbonyl nitrosyl

Under UV light irradiation on a gaseous mixture of Fe(CO)₅ and Co(CO)₃NO, both the crystalline deposits with sizes of 5 and 18 μm and the spherical particles with a mean diameter of 0.3 μm were produced. From FT-IR spectra and SEM–EDS analysis, it was suggested that the chemical structure of the crystalline deposits was the one of Fe₂(CO)₉ being modified by involving Fe(CO)Co bond. By decreasing a partial pressure of Fe(CO)₅ to 0.5 Torr in the gaseous mixture, only the spherical aerosol particles could be produced. Chemical composition of the particles was rich in Co species. From the disappearance of bridging CO band in the FT-IR spectra of the particles and the appearance of CO bands coordinated to a metal atom, Fe atom in Fe(CO)₄ was suggested to be coordinated by the O atom in bridging CO bond in Co(CO)Co structure and/or in α-diketone structure which was formed from two CO groups in dicobalt species. Chemical compositions of the crystalline deposits and the spherical particles were influenced differently by the application of a magnetic field. Atomic ratio of Fe to Co atom decreased in the crystalline deposits whereas it increased in the spherical particles with increasing magnetic field up to 5 T. Linearly aggregated particles (i.e., particle wires) as long as 30 μm were produced on the front side of a glass plate placed at the bottom of the irradiation cell.     

Simultaneous determination of chloride, nitrate and sulphate in vegetable samples by single-column ion chromatography

A new ion chromatography method is described for the simultaneous determination of Cl⁻, NO₃⁻ and SO₄²⁻, using a selected eluent 1.3-mM sodium gluconate/1.3-mM borax (pH 8.5). The extraction methods of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables are studied. The determination limits of Cl⁻, NO₃⁻, SO₄²⁻ are 0.17 μg/ml, 0.63 μg/ml and 0.81 μg/ml. The linear ranges are 060 μg/ml, 090 μg/ml and 090 μg/ml. The relative S.D. are <2.5%. The mean recoveries of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables range from 97.0 to 104%.     

Electrochemical properties of polyaniline in p-toluene sulfonic acid solution

Polyaniline was deposited potentiodynamically on a stainless steel substrate in the presence of an inorganic acids (sulfuric acid). The electrochemical characterization of the electrode was carried out by means of cyclic voltammetry and electrochemical impedance spectroscopy in the organic acids (p-toluene sulfonic acid) solution. The results show that polyaniline has a high specific capacitance of 431.8 F g⁻¹ at 1 mV s⁻¹, high coulombic efficiency of 95.6% at 20 mV s⁻¹, and exhibits a high reversibility. This indicates the promising feasibility of the polyaniline used as an electrochemical capacitor material in the electrolyte of p-toluene sulfonic acid solution especially at high charge–discharge process.     

Adsorption of a double-chain surfactant on an oxide

Adsorption of surfactants on solids is affected by the intermolecular packing in the adsorbed layer besides the driving forces. The adsorption behavior of a double-chain surfactant on silica is studied here along with that of the single-chain one. Comparison of adsorption of these two surfactants is warranted since while the single-chain surfactants form spherical micelles, the double-chain ones form bilayered vesicles in solution. While the adsorption of the single-chain surfactant reaches the plateau in a wide concentration range, the adsorption of the double-chain one increases sharply in a concentration range 10⁻⁵ mol/L up to the plateau. The single chain is found to form 1.5 monolayers under saturation coverage suggesting adsorption with reverse orientation at high concentration. In contrast, the adsorption of the double-chain surfactant under saturation coverage is equivalent to a 0.9 monolayer. Fluorescence tests revealed the hydrophobicity change of the surface with increase in adsorption. However, the hydrophobicity tests show the solid surface to be hydrophilic in this range; the double-chain surfactant is proposed to form a partial bilayer.     

Correlation between properties of a solid sample and laser-induced plasma parameters

To investigate the influence of mechanical properties of a solid sample on the laser-induced plasma parameters (temperature and mass ablated) a number of aluminum–lithium alloys and lithium ferrites with different microstructure and composition have been studied. The specific approach to estimate excitation temperature for low-resolution emission spectra has been developed. The main limitations of this approach were discussed on the basis of comparison with the energy width of several multiplets. Overall uncertainties for temperature calculation were evaluated by taking into account the accuracy of Einstein's coefficients and errors of the proposed multiplets method. The temporal evolution of laser plasma during the evaporation of these materials was studied. Extremely high value of the Li I excitation temperature has been estimated to be T > 10⁵ K for the annealed ferrite ablation, in contrast to the temperature T  1.5 · 10⁴ K for non-annealed ferrite. Only for ablation of annealed ferrite the Li II emission line at 548.4 nm was observed. It means that this laser-induced plasma was the hottest. In the case of alloys, the temperature calculated by using Li I transitions was proportional to the microhardness of the solid samples. The negative correlation between crater volume/opto-acoustic signal and alloy microhardness was observed. At the first pulses the mechanical properties of the alloys didn't correlate with the ablated mass, while the maximal correlation coefficients were observed after ablation by 10 or 50 consequent laser pulses.     

Fabrication and superhydrophobicity of fluorinated titanium dioxide nanocoatings

This study demonstrates the fabrication of a stable superhydrophobic surface with low contact angle hysteresis (CAH) using an arrangement of nanoscale TiO₂ spheres. The control of precursor quantity is selected as the key factor in determining surface roughness that significantly intensifies water contact angle (CA) of TiO₂ films. After surface fluorination treatment, the anatase-type crystalline surfaces exhibit good water repellency (CA 166.1°), low CAH (6°), and superhydrophobic stability (>60 min). Enhanced water repellency is attributed to the fact that the higher density of TiO₂ spheres results in more tortuous three-phase contact line, leading to the self-cleaning effect. Such a unique textured surface imparts many promising potentials for engineering and the development of optics devices with robust superhydrophobic materials.     

Ultrafast dynamics of heat flow across molecules

An ultrafast flash thermal conductance apparatus is used to study heat flow through aliphatic and aromatic molecules arranged in self-assembled monolayers (SAMs). The apparatus consists of a thin metal film which can be flash-heated by many hundreds of degrees in 1 ps using a femtosecond pulse. Heat flow from the metal surface into the SAM molecules is detected using vibrational sum-frequency generation (SFG) spectroscopy. The SAMs studied were alkanethiolates (AT) ranging from C6 to C24, benzenethiolate (BT) and benzylmercaptide (BMT). SFG in the CH-stretch region selectively probes transitions of the terminal methyl groups of AT and the CH moiety at the 4-position of the phenyl ring of BT and BMT (opposite the thiolate-surface bond). The SFG signal is sensitive to temperature-jump induced thermal disorder of the SAM and also to vibrational frequency shifts induced by the changing intramolecular vibrational populations. The SFG probe functions as a thermometer, and this thermometer is 1.5 Å thick with a response time of 1 ps. In the AT chains, a study of the length dependence is used to determine the rate heat flows across the metal–SAM interface and the rate of heat flow through the AT chains. The interface thermal conductance is 220 GW m⁻² s⁻¹. The AT molecular conductance is 50 pW K⁻¹ or 0.3 eV s⁻¹ K⁻¹. Heat flow through the AT chains is ballistic with a velocity of 1 km/s. Heat flow into BMT is slower than in BT because BMT has one additional methylene linker group. The BT and BMT structures evidence a thermally-initiated surface rearrangement occurring in a few tens of picoseconds. These SAMs are strained and the phenyl rings cannot adopt the most stable staggered herringbone structure. After the T-jump, the SAM molecules have enough freedom to relax into more favorable configurations.     

Efficient hydrogen peroxide generation from organic matter in a bioelectrochemical system

Hydrogen peroxide (H₂O₂) is an important industrial chemical, but its current production methods are highly energy-intensive. This study presents a novel process for the production of H₂O₂ based on the bioelectrochemical oxidation of wastewater organics at an anode coupled to the cathodic reduction of oxygen to H₂O₂. At an applied voltage of 0.5 V, this system was capable of producing 1.9 ± 0.2 kg H₂O₂/m³/day from acetate at an overall efficiency of 83.1 ± 4.8%. As most of the required energy was derived from the acetate, the system had a low energy requirement of 0.93 kWh/kg H₂O₂.     

An efficient biosurfactant-producing bacterium Pseudomonas aeruginosa MR01, isolated from oil excavation areas in south of Iran

A bacterial strain was isolated and cultured from the oil excavation areas in tropical zone in southern Iran. It was affiliated with Pseudomonas. The biochemical characteristics and partial sequenced 16S rRNA gene of isolate, MR01, was identical to those of cultured representatives of the species Pseudomonas aeruginosa. This bacterium was able to produce a type of biosurfactant with excessive foam-forming properties. Compositional analysis revealed that the extracted biosurfactant was composed of high percentages lipid (65%, w/w) and carbohydrate (30%, w/w) in addition to a minor fraction of protein (4%, w/w). The best production of 2.1 g/l was obtained when the cells were grown on minimal salt medium containing 1.2% (w/v) glucose and 0.1% (w/v) ammonium sulfate supplemented with 0.1% (w/v) isoleucine at 37 °C and 180 rpm after 2 days. The optimum biosurfactant production pH value was found to be 8.0. The MR01 could reduce surface tension to 28 mN/m and emulsified hexadecane up to E24  70. The results obtained from time course study indicated that the surface tension reduction and emulsification potential was increased in the same way to cell growth. However, maximum biosurfactant production occurred and established in the stationary growth phase (after 84 h). Fourier Transform Infrared spectrum of extracted biosurfactant indicates the presence of carboxyl, amine, hydroxyl and methoxyl functional groups. Thermogram of biosurfactant demonstrated three sharp endothermic peaks placing between 200 and 280 °C. The core holder flooding experiments demonstrated that the oil recovery efficiencies varied from 23.7% to 27.1% of residual oil.     

Excited state intramolecular proton transfer in a new o-hydroxy Schiff base in non polar solvents at room temperature and 77 K

A new orthohydroxy Schiff base, 7-ethylsalicylidenebenzylamine (ESBA) has been synthesised. The excited state intramolecular proton transfer (ESIPT) processes have been investigated by means of absorption, emission and nanosecond spectroscopy at room temperature and at 77 K in non polar solvents. The ESIPT is evidenced by a large Stokes shifted emission (11 000 cm⁻¹) only at 77 K. From fluorescence and excitation spectra it is suggested that at least three different species are present in the excited state at room temperature. Our theoretical calculation at AM1 level confirm the cis-isomer to be the only viable form in the ground state.     

Interaction and photodynamic activity of cationic porphyrin derivatives bearing different patterns of charge distribution with GMP and DNA

The interaction of amphiphilic cationic porphyrins, containing different patterns of meso-substitution by 4-(3-N,N,N-trimethylammoniumpropoxy)phenyl (A) and 4-(trifluoromethyl)phenyl (B) groups, with guanosine 5′-monophosphate (GMP) and calf thymus DNA have been studied by optical methods in phosphate buffer solution. The properties of these synthetic porphyrins were compared with those of representative standard of anionic 5,10,15,20-tetra(4-sulphonatophenyl)porphyrin (TPPS₄⁴⁻) and cationic 5,10,15,20-tetra(4-N,N,N-trimethylammonium phenyl)porphyrin (TMAP⁴⁺). Stable complexes with GMP were found for cationic porphyrins, except for monocationic AB₃⁺. The binding constant (K_GMP  10⁴ M⁻¹) follows the order: A₃B³⁺  ABAB²⁺ > A₄⁴⁺  TMAP⁴⁺. Also, interaction with DNA was observed for all evaluated cationic porphyrins. For these related cationic porphyrins, the binding constant (K_DNA  10⁵ M⁻¹) increases with the number of cationic charges. On the other hand, the photodynamic activity of porphyrins was analyzed in solution of GMP and DNA. Monocationic AB₃⁺ is a less effective sensitizer to oxidize GMP in comparison with the other cationic porphyrins, in agreement with the lack of detected interaction with this nucleotide. The electrophoretic analysis of DNA indicates that photocleavage takes place when the samples are exposed to photoexcited tricationic and tetracationic porphyrins. In the presence of sodium azide the DNA decomposition was diminished. Also, reduction in the DNA photocleavage was observed under anoxic condition, indicating that oxygen is essential for DNA photocleavage sensitized by these cationic porphyrins. In addition, an increase in DNA degradation was not observed in deuteriated water. Therefore, an important contribution of type I photoreaction processes could be occurring in the DNA photodamage sensitized by these cationic porphyrins. These results provide a better understanding of the characteristics needed for sensitizers to produce efficient DNA photocleavage.     

Effective arsenic removal using polyacrylonitrile-based ultrafiltration (UF) membrane

Applicability of polyacrylonitrile (PAN)-based negatively charged ultrafiltration (UF) membrane for effective arsenic removal has been demonstrated, to our knowledge, for the first time. The hydrolysis of PAN-based UF membrane surface by NaOH leading to the formation of carboxylate (COO⁻) groups and reduction in initial pore size rendered As-V rejection capability by Donnan exclusion principle. A lowering in pore size was indicated by the reduction in water flux and elevation in rejection of protein and polyethylene glycol (PEG). NaOH treatment leading to formation of carboxylate group on the membrane surface was indicated by FTIR-ATR, while contact angle measurement indicated increased hydrophilicity. This treatment rendered membrane surface smoothening as confirmed by SEM and AFM analyses. The molecular weight cut off after the NaOH treatment was found to be 6 kDa. The rejection of pentavalent arsenic (As-V) by these surface modified membranes was studied with different feed concentration, cross-flow velocity, pressure, temperature and pH. Experiments with 50 ppb As-V in feed showed that arsenic rejection was close to 100% and remained constant up to 6 h. Feed sample concentration of 1000 ppb and 50 ppm of As-V showed >95% rejection at pH 7 and room temperature, but for 1000 ppm feed concentration, the rejection was 40–65%. For concentrations ≤50 ppm of arsenic in the feed, the rejection coefficient was not dependent on cross-flow velocity or transmembrane pressure. The rejection for 1000 ppm concentration of As-V varied from 40 to 65% with variation in the cross-flow velocity and transmembrane pressure as the concentration polarization was important.     

Solvent effect on the blue shifted weakly H-bound F3 CH…FCD3 complex

Solvent effect on the ν^c frequency of CH stretching vibration of the blue shifted F₃CH…FCD₃ complex has been studied in liquefied N₂, CO, Ar, Kr and Xe. In the case of Xe, the spectroscopic measurements have also been extended to the solid state. It was found that the ν^c position of the complex in the solutions studied lowers with respect to the value in the gas phase. In liquid Xe, characterized by the largest permittivity, this effect reaches its maximum value of −14.5 cm⁻¹. The ν^c frequency begins to grow again just below the freezing point of Xe, where a noticeable (15%) increase of the density of Xe occurs. The experimental results obtained for the liquid phase have been analyzed in the framework of the Onsager-like reaction field model and Polarizable Continuum Model (PCM) implemented into a standard Gaussian 98 Program.     

Charge transport modulation of silicon nanowire by O2 plasma

The modification of the electrical characteristics of field-effect transistors (FETs) with channels composed of n- or p-type silicon nanowires (SiNWs) by oxygen plasma treatment is investigated in this study. The SiNWs obtained from silicon bulk wafers are <111> surface-oriented and their doping concentrations are 10²¹ and 10¹⁷ cm⁻³ for the n- and p-type SiNWs, respectively. After the back-gate SiNWFETs were subjected to oxygen plasma treatment, the magnitude of the drain current of the n-type SiNWs was decreased, whereas that of the p-type SiNWs was increased, while the gate-dependent characteristics of both of types of SiNWs were improved. The changes in the electrical characteristics are due to the adsorption of oxygen ions on the surface of the SiNWs. To verify the effect of the oxygen ions, the SiNWFETs were kept in a vacuum for 24 h whereupon their electrical characteristics tended to revert to their inherent state.