Flow injection spectrophotometric determination of ascorbic acid in soft drinks and beer

Two spectrophotometric methods, a photochemical and a non-photochemical, for the determination of ascorbic acid in soft drinks and beer using a flow-injection system are proposed. The non-photochemical method is based on the redox reaction that takes place between ascorbic acid and Fe(III), yielding dehydroascorbic acid and Fe(II). Fe(II) reacts with 1,10-phenantroline, originating the reddish orange Fe(phen)₃ ²⁺ complex (ferroin). This complex is spectrophotometrically monitored at 512 nm, and the signal is directly related to the concentration of ascorbic acid in the sample. The photochemical method has the same basis, nevertheless, uses the irradiation with visible light to enhance the redox reaction and so achieve higher sensitivities in the analysis. The non-photochemical method shows a linear range between 5 and 80 μg mL^?1, with a relative standard deviation of 1.6% (n = 11), a detection limit of 2.7 μg mL^?1 and a sample throughput of ¶60 samples h^?1. The photochemical method shows a linear range between 1 and 80 μg mL^?1, with a relative standard deviation of 1.0% (n = 11), a detection limit of 0.5 μg mL^?1 and a sample throughput of 40 samples h^?1.     

Flow injection spectrophotometric determination of lactic acid in skimmed milk based on a photochemical reaction

A spectrophotometric method for the determination of lactic acid in milk samples based on the use of a photochemical reaction carried out in a Flow Injection System is proposed. Determination is based on the reaction between lactic acid and Fe(III), which is reduced to Fe(II) in the presence of UV light, being the latter made to react with o-phenanthroline. The complex formed between Fe(II) and o-phenanthroline, Fe(o-phen)(3)(2+) (ferroin) is a coloured compound and it can be spectrophotometrically monitored at 512 nm. The method shows a linear range between 0.5 and 50 mug ml(-1) with a limit of detection of 0.16 mug ml(-1). The precision was +/-2.15 expressed as relative standard deviation (n=11) and the sample throughput of 30 samples h(-1). Also non-linear adjustments have been made and validated by ANOVA. The proposed method has been applied to the determination of lactic acid in both synthetic and milk samples.     

Fluorimetric determination of arsanilic acid by flow-injection analysis using on-line photo-oxidation

A flow-injection-fluorimetric method for the determination of arsanilic acid is proposed. The assay is based on the on-line decomposition of arsanilic acid in the presence of peroxydisulfate on irradiation with UV light. The arsenate generated in the photochemical reaction was reacted with molybdate in dilute nitric acid to form arsenomolybdic acid, which oxidised thiamine to thiochrome. The thiochrome was monitored fluorimetrically at 440 nm with excitation at 375 nm. The calibration graph was linear in the range 0.10-10.8 microg mL(-1) with a correlation coefficient of 0.999. The detection limit was 0.01 microg mL(-1) and the sample throughput was 55 samples h(-1). The applicability of the method was demonstrated by determining arsanilic acid in animal foodstuffs and water.     

Ferrozine colorimetry and reverse flow injection analysis (rFIA) based method for the determination of total iron in aqueous solutions at nanomolar concentrations

Iron is one of the most microbiologically and chemically important metals in natural waters. The biogeochemical cycling of iron is significantly influenced by the redox cycling of Fe(II) and Fe(III). Because of the unique chemistry of iron, it is often needed to analyze iron at nano-molar concentrations. This article describes a reverse flow injection analysis (rFIA) based method with ferrozine spectrophotometric detection to quantify total iron concentration in stream water at nanomolar concentrations. The rFIA system has a 0.65 nM detection limit and a linear dynamic range up to 1.40 μM for the total iron analysis. The detection limit was achieved using a 1.0 m long liquid waveguide capillary flow cell, 1.50 m long knotted reaction coil, 87.50 μL injection loop and a miniature fiber optics spectrophotometer. The optimized colorimetric reagent has 1.0 mM ferrozine, 0.1 M ascorbic acid, 1.0 mM citric acid and 0.10 M acetate buffer adjusted to pH 4.0. The best sample flow rate is 2.1 mL min^?1 providing a sample throughput of more than 15 samples h^?1. The linear dynamic range of the method can be adjusted by changing the volume of the injection loop. The rFIA manifold was assembled exclusively from commercially available components.     

Kinetic method for determination of ascorbic acid on flow injection system by using its catalytic effect on the complexation reaction of an ultra sensitive colorimetric reagent of porphyrin with Cu(II)

A kinetic method performed on a flow injection system is described for the determination of ascorbic acid by using its catalytic effect on the complexation reaction of Cu(II) with 5,10,15,20-tetrakis(4-N-trimethyl-aminophenyl)porphyrin. The characteristic spectrum of porphyrin (Soret band), which shows intense absorption around 400 nm (epsilon>2.0 x 10(5) cm(-1)M(-1)), was used first time for determining ascorbic acid. By incorporating the complexation reaction into a flow injection system, ascorbic acid could be determined either over a broad dynamic range of 0.1-1000 microg/ml or at a trace level below 5 ng/ml. Good repeatability was also achieved by testing a working standard of 0.1 microg/ml with 10 injections at a throughput of 35 h(-1), obtaining a relative standard deviation of 0.11%. Substances like amino acids, vitamins, sugars, organic acids and metal ions, showed no or little interference even present at high concentrations. The method was validated in the determination of ascorbic acid contents of some commercially available soft drinks by comparison with the official 2,6-dichloroindophenol method with reasonable agreement.     

Determination of salbutamol using on-line solid-phase extraction and sequential injection analysis. Comparison of chemiluminescence and fluorescence detection

Determination of salbutamol using sequential injection analysis (SIA) with chemiluminescence and fluorescence detection has been devised. The chemiluminescence signal was emitted during the oxidation of salbutamol by potassium permanganate in sulfuric acid medium. Sodium polyphosphate was used as chemiluminescence enhancer. The fluorescence signal (excitation wavelength 230 nm) was also measured in sulfuric acid medium. Both detection techniques were compared with respect to the application of the methods to the determination of salbutamol in biological materials. The sample pre-treatment takes place directly in the SIA system, when salbutamol is adsorbed on the solid-phase (Baker-carboxylic acid) microcolumn integrated into the system. Sulfuric acid serves both as the reagent and the eluent. The lab-made SIA system consisted of a 2.5-mL Cavro syringe pump, ten-port Vici Valco selection valve and Spectra-Physics FS 970 fluorescence detector, which was lab-modified for chemiluminescence detection. The system was controlled by a PC using originally compiled LabVIEW-supported software. Concentrations, volumes of reagents and flow rates were optimised by a simplex method. Salbutamol was determined in the linear range 0.05-10 microg mL(-1) (RSD 1.53%), with the detection limit (3 sigma) 0.03 microg mL(-1) and sample throughput of 42 samples per hour with chemiluminescence detection in standard solutions. The fluorescence detection enabled the determination of salbutamol in standard solutions in the linear range 0.5-100 microg mL(-1) (RSD 2.69%), with the detection limit 0.2 microg mL(-1) and sample throughput of 24 h(-1). The proposed methods were applied to the determination of salbutamol in human serum and urine. However, serum is a very complicated matrix and the SIA-SPE analysis did not provide satisfactory results. It was possible to determine salbutamol in human urine using this technique. Better recovery was achieved with fluorescence detection.     

Rapid speciation of trace iron in rainwater by reverse flow injection analysis coupled to a long path length liquid waveguide capillary cell and spectrophotometric detection

A method for speciation and determination of low levels of dissolved iron in rainwater was established by coupling reverse flow injection analysis with a 2-m liquid waveguide capillary cell and spectrophotometric detection. Ferrozine solution was injected into a sample stream to form an Fe(II)-ferrozine complex with Fe(II), and the absorbance of this complex was detected at both 562 nm and 625 nm with a reference wavelength at 700 nm. Fe(III) was analyzed in the same manner after being reduced to Fe(II) by ascorbic acid. The optimum conditions and the interference of Cu(I), Ni(II) and Co(II) were investigated. The limits of detection were 0.1 nM for Fe(II) and 0.2 nM for Fe(III), while the linear ranges were 0.4 – 200 nM for Fe(II) and 0.8 – 287 nM for Fe(III) at 562 nm, and can be extended to higher concentrations with the detection at a less sensitive wavelength of 625 nm. The sample throughput was 6 h^?1, and the total sample volume consumed was 10 mL. This method has been successfully applied to analyze dissolved iron in rainwater of Xiamen from August to November, 2008. The lowest level of iron in rainwater was observed during typhoon events. By adopting reverse flow injection analysis coupled with liquid waveguide long path length capillary cell, the reagent consumption was low and the sensitivity was enhanced. The other advantages of this method are high sample throughput, wide linear dynamic range and high selectivity for Fe(II).     

Asynchronous merging zones system: spectrophotometric determination of Fe(II) and Fe(III) in pharmaceutical products

An asynchronous merging zones was proposed with simultaneous introduction of the sample and of the modifier reagent, ascorbic acid in the studied case, for sequential determination of Fe(II) and Fe(III) in pharmaceutical products. The sample and reagent attained a merging point at different times owing to the use of a delay reactor in the reagent channel. By inserting a large sample and controlling the dispersion in the flow system, Fe(II) and Fe(III) were sequentially measured in the front and in the rear of the sample zone, respectively. The results obtained for Fe redox speciation in pharmaceutical products are in agreement at a 95% confidence level with those obtained with a manual spectrophotometric procedure. The analytical frequency with the proposed flow analysis system was 54 samples h(-1), i.e. 108 determinations h(-1).     

Sensitive monitoring of humic acid in various aquatic environments with acidic cerium chemiluminescence detection.

In this research, a simple, sensitive chemiluminescence (CL) method for the determination of humic acid (HA) in water samples was first developed based on the redox reaction between humic acid and cerium(IV) in the acidic condition. Different with the former redox CL reaction which occurred in alkaline solution, no enhancers were needed and neither precipitation nor a second contamination would occur in the present CL system. Comparing with other spectrometric methods, we find that the proposed analysis system had better applicability and accuracy. Under the optimal experiment conditions, the CL peak height was linear with the concentration of HA in the range of 0.03 to 10.0 microg mL(-1). The detection limit is 0.01 microg mL(-1) (S/N = 3), and the relative standard deviation was 2.3% for 0.5 microg mL(-1) HA solution with eleven repeated measurements. The present CL method was successfully applied to the determination of HA in tap water, spring water and river water samples with good recovery from 90.0 to 110.0%. A possible CL mechanism was proposed based on the results of UV and fluorescence spectrometry and the CL spectrum of HA. It was speculated that the semi-quinone radicals in the excited state were the emitters.     

Chemiluminescence flow sensor with immobilized reagent for the determination of pyrogallol based on potassium hexacyanoferrate(III) oxidation

A novel chemiluminescence (CL) flow-through sensor for the determination of pyrogallol has been developed. The method is based on the reaction between pyrogallol and potassium hexacyanoferrate(III) in sodium hydroxide solution. Potassium hexacyanoferrate(III) involved in the CL reaction was electrostatically immobilized on anion-exchange resin packed in a column. Pyrogallol was sensed by the CL reaction between pyrogallol and potassium hexacyanoferrate(III) which was eluted from the ion-exchange column through sodium phosphate injection. The CL emission allows quantitation of pyrogallol concentration in the range 0.01-3.8 microg/mL with a detection limit (3 sigma) of 0.003 microg/mL and a sample throughput of 118 h(-1). The relative standard deviation (n=7) was 2.2% for 0.2 microg/mL of pyrogallol. The influence of foreign compounds was tested.     

Speciation of dissolved iron(II) and iron(III) in environmental water samples by gallic acid-modified nanometer-sized alumina micro-column separation and ICP-MS determination

A method has been developed for the speciation of trace dissolved Fe(II) and Fe(III) in water by coupling gallic acid (GA) modified nanometer-sized alumina micro-column separation with inductively coupled plasma mass spectrometry (ICP-MS). The separation of Fe(II) and Fe(III) was achieved based on the obvious difference in reaction kinetics between Fe(II) and Fe(III) with GA. Fe(III) was selectively retained on the micro-column at pH 5.5-6.5, while Fe(II) could not be retained by the micro-column at the whole tested pH range of 1.0-6.5, and passed through the micro-column. The Fe(II) can be determined by ICP-MS directly without preconcentration/separation procedure, while Fe(III) retained on the micro-column was then eluted with 1.0 mL of 1 mol L(-1) HCl and determined by ICP-MS. The parameters affecting the separation of Fe(II) and Fe(III) were investigated systematically and the optimum separation conditions were established. Under the optimized conditions, the detection limits of 0.48 microg L(-1) and 0.24 microg L(-1) with relative standard deviation of 5.6% and 4.3%(C= 5 microg L(-1), n= 7) for Fe(II) and Fe(III) were found, respectively. No obvious effect on the speciation of Fe(II) and Fe(III) was found with the change of the ratio of Fe(II) and Fe(III) from 0 ratio 10 to 10 ratio 0. The proposed method was applied for the determination of trace Fe(II) and Fe(III) in environmental water and the recoveries for spiked samples were found to be in the range of 97-105%.     

Flow injection determination of methamidophos using online photo-oxidation and fluorimetric detection

A photochemical method for the determination of methamidophos using a flow injection system is proposed. The method is based on the rapid decomposition of methamidophos in the presence of peroxydisulphate upon irradiation with UV light. The phosphate generated in the photochemical process is made to react with molybdate in dilute nitric acid to form phosphomolybdic acid, which oxidises thiamine to thiochrome. The thiochrome can then be fluorimetrically monitored at 440 nm with excitation at 375 nm. The method shows a linear range between 14 and 1400 ng ml(-1) with a limit of detection of 1.7 ng ml(-1). The repeatability was 0.3% expressed as relative standard deviation (n=10) and the reproducibility, studied on five different days, was +/-3%. The sample throughput was 70 injections per h. The reliability of the method for routine analysis of water and vegetable samples is demonstrated.     

Kinetic spectrofluorimetric determination of trace ascorbic acid based on its inhibition on the oxidation of pyronine Y by nitrite

A highly sensitive spectrofluorimetric method is proposed for the determination of trace amount of ascorbic acid using a new indication. The method is based on the inhibition of ascorbic acid on the oxidation of pyronine Y (PRY) by nitrite. The detection limit for ascorbic acid is 0.012 microg ml(-1), the linear range of the determination is 0.02-0.36 microg ml(-1). Analytical parameters, such as reagent concentration, pH, reaction temperature and time, were optimized. The relative standard deviations of eleven replication determinations of 0.12 and 0.24 microg ml(-1) ascorbic acid were 1.4 and 0.72%, respectively. This method has been used to determine ascorbic acid in pharmaceuticals, vegetables, fruits and soft drink with satisfactory results.     

Univariate and simplex optimization for the flow-injection spectrophotometric determination of copper using nitroso-R salt as a complexing agent.

A simple colorimetric flow-injection system for the determination of Cu(II) based on a complexation reaction with nitroso-R salt is described. The chemical and FIA variables were established using the univariate and simplex methods. A small volume of Cu(II) was mixed with merged streams of nitroso-R salt and acetate buffer solutions. The absorbance of the complex was continuously monitored at 492 nm. The calibration curve over the concentration range 1.0-7.0 microg ml(-1) was obtained. The relative standard deviation for determining 4.0 microg ml(-1) Cu(II) was 0.47% (n = 11). The detection limit (3sigma) was 0.68 microg ml(-1) and the sample throughput was 150 h(-1). The validity of the method has been satisfactorily examined for the determination of Cu(II) in wastewater and copper ore samples. The accuracy was found to be high, because the student t-values were calculated to be less than the theoretical values when the results were compared with those obtained by FAAS.     

Rapid determination of dissolved organic phosphorus in soil leachates and runoff waters by flow injection analysis with on-line photo-oxidation

A rapid method suitable for the determination of dissolved organic phosphorus (DOP) in soil leachates and runoff waters is presented. The flow injection (FI) manifold contains an in-line PTFE reaction coil wrapped around a low power UV lamp and is based on the spectrophotometric determination of dissolved reactive phosphorus (DRP) and mineralised DOP at 690 nm after reduction of phosphomolybdate to molybdenum blue with tin(II) chloride. The linear range was 0-1.5 mg 1(-1) PO(4)-P, with a detection limit (3 s) of 7 mug 1(-1) and a sample throughput of 40 h(-1). Tolerance to potential matrix interferences in soil pore waters, particularly Al(III), Si(IV), Fe(II) and Fe(III), was achieved using a combination of on-line sample pre-treatment by a strong acid ion exchange column, low photoreactor pH and acid induced control of the kinetics of the molybdenum blue reaction. The results obtained with this manifold were in good agreement with those obtained by a batch spectrophotometric reference method.     

Spectrophotometric method for the determination of ascorbic acid with iron (III)-1,10-phenanthroline after preconcentration on an organic solvent-soluble membrane filter

A solvent-soluble membrane filter is proposed for the simple and rapid preconcentration and spectrophotometric determination of ascorbic acid based on the reduction of 1, 10-phenanthroline (phen)-iron (III), which is collected on a nitrocellulose membrane filter as an ion-associate of the cationic complex of tri,phen-iron (II) [ferroin, Fe(phen)(2+)(3)] with an anionic surfactant (of dodecyl sulfate). The ion-associate collected is dissolved in a small volume of 2-methoxyethanol together with the filter. The colour intensity is measured at 510 nm against the reagent blank and is proportional to the content of ascorbic acid in the range 2.5-50 microg ascorbic acid in 5 ml of solvent with excellent reproducibility (RSD 3.2% for 200 microg 1(-1) ascorbic acid), the enrichment factor achieves 100-fold and detection limits better than 2.0 microg 1(-1) can be obtained. Diverse components of organic and inorganic compounds normally present in fruits, vegetable, beverages and urine do not interfere. The recoveries of the ascorbic acid added to the samples are quantitative.     

Precolumn derivatization liquid chromatography method for analysis of dietary supplements for glucosamine: single laboratory validation study

A precolumn derivatization liquid chromatography (LC) method was developed for the analysis of various dietary supplement formulations and raw materials for glucosamine. A 1 mL sample or standard water solution (containing about 0.05 mg glucosamine) was mixed with 1 mL pH 8.3 buffer, 1 mL 5% phenylisothiocyanate methanolic solution, and derivatized at 80 degrees C in a water bath for 30 min. After derivatization, the solution was cooled in a cold water bath and centrifuged at 3000-5000 rpm. The clear upper layer was ready for injection. The LC system was equipped with a C18 reversed-phase column and an ultraviolet detector set at 240 nm. The column was developed with a linear gradient composed of 0.1% phosphoric acid in deionized water and 0.1% phosphoric acid in methanol. The method was subjected to Single Laboratory Validation. The method precision was 0.50% relative standard deviation, accuracy was less than +/-1.5%, method linearity in the range 0-2 mg glucosamine/mL was 1.00, the detection limit was 0.0705 microg/mL, and the quantitation limit was 0.235 microg/mL. Chondroitin sulfate, amino acids, and excipients did not interfere with glucosamine testing. After derivatization, both standard and sample preparations were stable for at least 48 h. Due to its high sensitivity, this method can be used to assay glucosamine in functional foods and pet foods. The validation data will be published separately.     

Flow injection spectrophotometric determination of ultra trace amounts of oxalic acid

A new simple, sensitive and rapid catalytic-spectrophotometric method for the determination of oxalic acid has been described based on its catalytic effect on the redox reaction between dichromate and Brilliant cresyl blue in acidic media by means of a flow injection analysis method. The color change of Brilliant cresyl blue due to its oxidation was monitored spectrophotometrically at 625 nm. The calibration graph was linear in the range of 0.020-4.70 microg/mL oxalic acid with a limit of detection 0.005 microg/mL of oxalic acid. The relative standard deviation for ten replicate measurements of 0.020 microg/mL and 0.900 microg/mL was 2.2% and 1.7%, respectively. No serious interference was identified. Oxalic acid was determined in wastewater and in spinach by the proposed method with satisfactory results.     

Concentrations of hazardous heavy metals in environmental samples collected in Xiamen, China, as determined by vapor generation non-dispersive atomic fluorescence spectrometry.

Non-dispersive atomic fluorescence spectrometry (NDAFS) coupled with vapor generation (VG) sample introduction was applied to the determination of the concentrations of hazardous heavy metals, such as arsenic, cadmium, lead and mercury, in seawater, soils and total airborne particulate matter (PM) collected around the Xiamen area in China. Almost 100% sample introduction efficiency was achieved by using thiourea and ascorbic acid for the pre-reduction of As(V) to As(III), K3Fe(CN)6 and tartaric acid for pre-oxidation of Pb(II) to Pb(IV), and masking the interferences arising from the co-existing transition metals to As, Cd, Hg and Pb during their vapor generation process. Moreover, a novel sample pretreatment device was developed to avoid the loss of mercury, lead, cadmium and arsenic during sample pretreatment. With such methods, the detection limit (DL) of arsenic, cadmium, lead and mercury was down to 0.08, 0.03, 0.05, 0.01 ng mL(-1) (3sigma), respectively. The relative standard deviations (RSD, n = 11) for arsenic, cadmium, lead and mercury at 10 ng mL(-1) were 0.9%, 1.6%, 1.3% and 2.0%, respectively. The concentrations of hazardous heavy metals in the environmental samples collected in Xiamen, China are in the range from 0.02 +/- 0.001 ng mL(-1) in seawater to 15.3 +/- 0.2 microg g(-1) in soils. Besides flame/GF-AAS and ICP-AES/MS, VG-NDAFS should be another choice for the determination of hazardous heavy metals in environmental samples.     

Flow injection analysis: Rayleigh light scattering technique for total protein determination

A novel flow injection analysis (FIA) method with Rayleigh light scattering (RLS) detection was developed for the determination of total protein concentrations. This method is based on the weak intensity of RLS of bromothymol blue (BB) (3',3"-dibromothymolsulfonephthalein) which can be enhanced by the addition of protein in weakly acidic solution. A common spectrofluorimeter was used as a detector. It was proved that the application of this method to quantify the total proteins in real samples by using bovine serum albumin was possible. The RLS signal was detected at lambda(ex)= lambda(em)=572 nm. The linear range was 7.0-70.0 microg mL(-1), the detection limit was 3.75 microg mL(-1), the reproducibility was 5.5% (n=7), and the sample throughput was 26 h(-1).