Phase transitions in O/W lauryl acrylate emulsions during phase inversion,studied by light microscopy and cryo-TEM

Phase changes during the preparation of nano-emulsions containing polymerizable monomer as the oil phase, by the phase inversion temperature technique (PIT), were investigated using light microscopy, cryo-TEM and viscosity measurements. The nano-emulsions were prepared using a poly(oxyethylene) nonionic surfactant and a polymerizable acrylic monomer (lauryl acrylate) as the oil phase. Inversion of the emulsion, followed by rapid cooling, resulted in emulsions having an average droplet size as low as 25 nm. Cryo-TEM was used to observe the structures that are present above and below the phase transition temperature, and gave, for the first time, visual indication of the presence of a microemulsion and a locally ordered structure in the process. At high surfactant concentrations, the inversion–cooling process yields emulsions with unique structures, in which the oil phase is present as worm-like structures.     

纳米SiO2/十二烷基氨基丙酸钠协同稳定的pH响应性Pickering乳状液

用纳米SiO₂颗粒与微量氨基酸型两性表面活性剂十二烷基氨基丙酸钠作复合乳化剂, 以正癸烷为油相, 制备了pH响应性O/W型Pickering乳状液. 室温下该乳状液在pH≤4.0 时稳定, 在pH≥6.0时不稳定, 因此, 可以通过改变水相的pH值使乳状液在稳定和破乳之间多次循环. 在酸性水介质中, 氨基酸型两性表面活性剂分子呈阳离子状态, 可通过静电作用吸附到带负电荷的SiO₂颗粒表面, 产生原位疏水化作用, 使其转变为表面活性颗粒; 而在中性和碱性水介质中, 氨基酸型两性表面活性剂呈两性或阴离子状态, 不能产生原位疏水化作用, 因而导致乳状液破乳. 相关作用机理通过吸附量、 Zeta电位及接触角等实验数据得以论证. 该刺激-响应性Pickering乳状液在乳液聚合、 油品输送以及燃料生产等领域具有重要的应用价值.     

Phase behavior and nano-emulsion formation by the phase inversion temperature method

Formation of oil-in-water nano-emulsions has been studied in the water/C12E4/isohexadecane system by the phase inversion temperature emulsification method. Emulsification started at the corresponding hydrophilic-lipophilic balance temperature, and then the samples were quickly cooled to 25 degrees C. The influence of phase behavior on nano-emulsion droplet size and stability has been studied. Droplet size was determined by dynamic light scattering, and nano-emulsion stability was assessed, measuring the variation of droplet size as a function of time. The results obtained showed that the smallest droplet sizes were produced in samples where the emulsification started in a bicontinuous microemulsion (D) phase region or in a two-phase region consisting of a microemulsion (D) and a liquid crystalline phase (L(alpha)). Although the breakdown process of nano-emulsions could be attributed to the oil transference from the smaller to the bigger droplets, the increase in instability found with the increase in surfactant concentration may be related to the higher surfactant excess, favoring the oil micellar transport between the emulsion droplets.     

Formation and stability of paraffin oil-in-water nano-emulsions prepared by the emulsion inversion point method

Paraffin oil-in-water nano-emulsions stabilized by Tween 80/Span 80 were prepared using the emulsion inversion point method at different emulsification temperatures. Nano-emulsions with droplet size below 200 nm were formed above a critical surfactant-to-oil ratio of 0.20 at 50 degrees C. The main destabilization mechanism of the systems was found to be Ostwald ripening. An interesting phenomenon was that the Ostwald ripening rate declined as the surfactant concentration rose. Furthermore, flocculation was also found to contribute to the instability of the nano-emulsions, especially for those with low surfactant concentrations. Study on the electrophoretic properties of emulsion droplets revealed a negative value of the zeta potential, which was strongly dependent on the pH of the systems.     

The influence of surfactant mixing ratio on nano-emulsion formation by the pit method

The formation of O/W nano-emulsions by the PIT emulsification method in water/mixed nonionic surfactant/oil systems has been studied. The hydrophilic-lipophilic properties of the surfactant were varied by mixing polyoxyethylene 4-lauryl ether (C12E4) and polyoxyethylene 6-lauryl ether (C12E6). Emulsification was performed in samples with constant oil concentration (20 wt%) by fast cooling from the corresponding HLB temperature to 25 degrees C. Nano-emulsions with droplet radius 60-70 nm and 25-30 nm were obtained at total surfactant concentrations of 4 and 8 wt%, respectively. Moreover, droplet size remained practically unchanged, independent of the surfactant mixing ratio, X(C12E6). At 4 wt% surfactant concentration, the polydispersity and instability of nano-emulsions increased with the increase in X(C12E6). However, at 8 wt% surfactant concentration, nano-emulsions with low polydispersity and high stability were obtained in a wide range of surfactant mixing ratios. Phase behavior studies showed that at 4 wt% surfactant concentration, three-liquid phases (W+D+O) coexist at the starting emulsification temperature. Furthermore, the excess oil phase with respect to the microemulsion D-phase increases with the increase in X(C12E6), which could explain the increase in instability. At 8 wt% surfactant concentration, a microemulsion D-phase is present when emulsification starts. The low droplet size and polydispersity and higher stability of these nano-emulsions have been attributed, in addition to the increase in the surface or interfacial activity, to the spontaneous emulsification produced in the microemulsion D-phase.     

pH-Sensitive self-propelled motion of oil droplets in the presence of cationic surfactants containing hydrolyzable ester linkages

Self-propelled oil droplets in a nonequilibrium system have drawn much attention as both a primitive type of inanimate chemical machinery and a dynamic model of the origin of life. Here, to create the pH-sensitive self-propelled motion of oil droplets, we synthesized cationic surfactants containing hydrolyzable ester linkages. We found that n-heptyloxybenzaldehyde oil droplets were self-propelled in the presence of ester-containing cationic surfactant. In basic solution prepared with sodium hydroxide, oil droplets moved as molecular aggregates formed on their surface. Moreover, the self-propelled motion in the presence of the hydrolyzable cationic surfactant lasted longer than that in the presence of nonhydrolyzable cationic surfactant. This is probably due to the production of a fatty acid by the hydrolysis of the ester-containing cationic surfactant and the subsequent neutralization of the fatty acid with sodium hydroxide. A complex surfactant was formed in the aqueous solution because of the cation and anion combination. Because such complex formation can induce both a decrease in the interfacial tension of the oil droplet and self-assembly with n-heptyloxybenzaldehyde and lauric acid in the aqueous dispersion, the prolonged movement of the oil droplet may be explained by the increase in heterogeneity of the interfacial tension of the oil droplet triggered by the hydrolysis of the ester-containing surfactant.     

Emulsification through surfactant hydration: the PIC process revisited

We have performed sudden composition changes on a (surfactant + oil + water) system by adding water to a (surfactant + oil) solution. This composition change quenches the system into a metastable oil-in-water emulsion with a population in the 100 nm range. The conditions for a successful quench are as follows: the initial water content should be below a boundary called the "clearing boundary" (CB), the final water content should be sufficiently beyond CB, and the quench should be fast. We have used high purity components to avoid the complex phase separation patterns that occur with low purity ingredients: the surfactant is octaethylenehexadecyl ether (C(16)E(8)) and the oil is hexadecane (C(16)). Under these conditions, we show that the pathway for this type of quench proceeds through the swelling of the reverse micellar phase by the added water and the formation of a sponge phase. Then, further water addition causes the nucleation of oil droplets in this sponge phase, with a size that matches the spontaneous curvature of the sponge phase. Part of the surfactant remains adsorbed on these droplets, and the rest is expelled as micelles that coexist with the droplets. It is concluded that a PIC emulsification will always lead to a bimodal size distribution with surfactant "wasted" in small micelles. This is in contrast with the more efficient PIT emulsification.     

Novel Oil‐in‐Water Emulsions Stabilised by Ionic Surfactant and Similarly Charged Nanoparticles at Very Low Concentrations

Novel oil‐in‐water (O/W) emulsions are prepared which are stabilised by a cationic surfactant in combination with similarly charged alumina nanoparticles at concentrations as low as 10^?5 m and 10^?4 wt %, respectively. The surfactant molecules adsorb at the oil‐water interface to reduce the interfacial tension and endow droplets with charge ensuring electrical repulsion between them, whereas the charged particles are dispersed in the aqueous films between droplets retaining thick lamellae, reducing water drainage and hindering flocculation and coalescence of droplets. This stabilization mechanism is universal as it occurs with different oils (alkanes, aromatic hydrocarbons and triglycerides) and in mixtures of anionic surfactant and negatively charged nanoparticles. Further, such emulsions can be switched between stable and unstable by addition of an equimolar amount of oppositely charged surfactant which forms ion pairs with the original surfactant destroying the repulsion between droplets.     

Preparation of microspheres by an emulsification-complexation method

Microspheres were prepared by complexation of a cationic polymer, polyquaternium-24, and an anionic surfactant, sodium lauryl sulfate (SLS). The cationic polymer solution was emulsified in dimethylsiloxane to give water in silicone emulsion (W/Si), and it was used as a template for the formation of microspheres. The emulsion was dispersed into the SLS solution. In this process, two kinds of droplets, silicone dropletes and microspheres composed of the cationic polymer and SLS, were formed, evidenced by X-ray energy dispersive spectra. The mean diameter of the microspheres was reduced from 105.7 to 64.8 mum as the stirring rate for W/Si preparation increased from 300 to 1000 rpm. It is believed that water droplets in W/Si emulsion, when exposed to SLS solution, could be solidified by the complexation of the cationic polymer and the anionic surfactant.     

Oil coating on hydrophilic surfaces from emulsions and under shear flow

We study the formation of silicone oil coating on negatively charged hydrophilic surfaces via emulsion deposition. Cationic surfactants usually adsorb and form bilayers onto negative surfaces. As a result, direct emulsions stabilized with cationic surfactants are paradoxically poorly efficient at coating negative substrates. We show in this work an alternative and new method, still based on electrostatic attractions, to coat negative substrates. Our method consists of using emulsions stabilized with nonionic surfactants and of adding to the oil cationic additives that are non-water-soluble and of high molecular weight to minimize their solubilization in the micelles formed by the neutral surfactant. The positively charged droplets stick efficiently onto the substrates. They form monolayer and uniform coatings. We study the kinetics and the density of the resulting coating using a flow cell experiment. This technique allows us to finely analyze the influence of several physicochemical parameters.     

On the Stability of Liquid Nanodroplets in Polymerizable Miniemulsions

Liquid nanodroplets within a size range of 50 to 500 nm can easily be prepared by shearing a system containing oil, water and a surfactant. The growth of the nanodroplets can effectively be suppressed by using a strong hydrophobe as an additivie to the oil and an effective surfactant. The hydrophobe acts as an osmotic agent which stabilizes the system against Ostwald ripening. The growth of the droplets by collision is controlled by the density of the surfactant layer. Freshly prepared miniemulsions are “critically stabilized” and show a slow, but pronounced growth, whereas a miniemulsion in “equilibrium” exhibits constant droplet size on longer time scales. Polymerization of the oil droplets of such miniemulsions turns out to be very promising and extends the possibilities of classical emulsion polymerization. Since each droplet can be considered a small reactor in which polymerization reactions take place, the process allows one to create new particle structures, e.g. polyaddition reactions can take advantage of unusual monomers, the incorporation of materials which are not soluble in the continuous phase, and the formation of nanocapsules.     

Effect of cetyltrimethylammonium bromide addition on the emulsions stabilized by montmorillonite

The wettability of montmorillonite could be in situ modified by cationic surfactant cetyltrimethylammonium bromide (CTAB). The type and stability of emulsions prepared from montmorillonite with different concentrations of cationic surfactant were investigated, and a double phase inversion of emulsions was observed. The adsorption of CTAB on montmorillonite particles was studied by surface tension and zeta potential measurements, and the variation of the wettability of particles with the concentration of CTAB was characterized by the contact angle measurements. The adsorption of particles at the surface of emulsion droplets was observed by laser-induced confocal scanning microscopy. At low surfactant concentrations, the adsorption of CTAB on montmorillonite increased the hydrophobicity of the particles, and the stability of oil-in-water emulsions was enhanced. With the increase of the CTAB concentration, montmorillonite particles changed from hydrophilic to hydrophobic, and water-in-oil emulsions were obtained. However, at higher surfactant concentrations, the emulsions inverts to O/W again because montmorillonite particles were reconverted into hydrophilic due to the formation of CTAB bilayer on the surface of montmorillonite.     

纳米SiO2与阳离子表面活性剂的相互作用及其诱导的正辛烷-水乳状液的双重相转变

研究了3种不同结构的水溶性阳离子表面活性剂对纳米二氧化硅颗粒的原位表面活性化作用, 它们分别是单头单尾的十六烷基三甲基溴化铵(CTAB)、单头双尾的双十二烷基二甲基溴化铵(di-C12DMAB)和双头双尾的Gemini型阳离子三亚甲基-二(十四酰氧乙基溴化铵)(II-14-3), 并通过测定Zeta电位、吸附等温线及接触角等参数对相关机理进行了阐述. 结果表明, 阳离子表面活性剂吸附到颗粒/水界面形成以疏水基朝向水的单分子层, 从而增强了颗粒表面的疏水性是原位表面活性化的基础. 通过吸附CTAB和II-14-3, 颗粒的疏水性适当增强, 能吸附到正辛烷/水界面稳定O/W(1)型乳状液; 而通过吸附di-C12DMAB所形成的单分子层更加致密, 颗粒的疏水性进一步增强, 进而使乳状液从O/W(1)型转变为W/O型; 当表面活性剂浓度较高时, 由于链-链相互作用, 表面活性剂分子将在颗粒/水界面形成双层吸附, 使颗粒表面变得亲水而失去活性, 但此时体系中游离表面活性剂的浓度已增加到足以单独稳定O/W(2)型乳状液的程度. 因此当采用纳米二氧化硅和di-C12DMAB的混合物作乳化剂时, 通过增加di-C12DMAB的浓度即可诱导乳状液发生O/W(1)→W/O→O/W(2)双重相转变.     

Water pH and surfactant addition effects on the stability of an Algerian crude oil emulsion

In many oil production sites water injection is used as a piston to push the crude out of the well. As the age of the field progresses, the ratio of water to oil produced increases. Agitation of a water and crude oil mixture may give stable water-in-oil emulsion in which the water remains dispersed for a long period of time. These emulsions can cause severe problems in production and transport processes since they normally possess high stability and viscosity. The most important water properties which may contribute to the emulsion stability include pH and additive content. In this study, we report on the effect of both, water pH and the presence of surfactant molecules (anionic, cationic or non-ionic) on the stability of an Algerian crude oil (Haoudh el Hamra well) aqueous emulsion prepared by a mechanical agitation procedure. The stability was followed by the test-bottle method to measure the resolved water separated from the emulsion, and optical microscopy to visualize the dispersed water droplets in the oil phase. The results of the effects of varying the aqueous-phase pH suggest that the neutral medium is more efficient than acidic or basic environment for stabilizing the emulsions. The addition of non-ionic surfactants has a better potential to improve crude oil emulsion stability with respect to both cationic and anionic surfactants which do not show any improvement in the oil/water phase compatibility.     

Oxidative stability and effect of stress factors on flaxseed oil-in-water emulsions stabilized by sodium caseinate–sodium alginate–chitosan interfacial membrane

The susceptibility of heart healthy ω-3 fatty acids to lipid oxidation has hindered its incorporation into healthful foods and beverages. In this study, plant-based flaxseed oil rich in ω-3 fatty acids were dispersed into primary, secondary and tertiary emulsion system. A primary emulsion containing sodium caseinate-stabilized cationic droplets was prepared by homogenizing flaxseed oil as oil phase and sodium caseinate solution as the aqueous phase in an ultrasonicator. A secondary emulsion comprising of sodium caseinate–sodium alginate anionic droplets were produced by diluting appropriate primary emulsion with alginate solution. Further, a tertiary emulsion composed of sodium caseinate–sodium alginate–chitosan-coated cationic droplets was produced by diluting secondary emulsion with chitosan solution. The resistance of primary, secondary and tertiary emulsions with the same lipid concentration to destabilization by thermal treatment (30–90 °C for 30 min), sodium chloride addition (≤70 mM NaCl) and oxidative degradation (hydroperoxide concentration and TBARS) was determined. The results showed that secondary emulsions could resist variation in environmental stresses of salt and heat as well as protect the oil phase from decomposition better than primary and tertiary emulsions. Interfacial engineering could be used to design emulsion system with desirable characteristics.     

MINIEMULSION FORMATION BY TRANSITIONAL INVERSION

Very fine emulsions with droplet size in the sub-micron range, often called miniemulsions, are prepared by the moderate (magnetic) stirring of a system undergoing a dynamic transitional inversion driven by a continuous change in physicochemical formulation (here temperature). Near optimum formulation for three-phase systems, the ultralow interfacial tension favors the drop breaking rate, and fine emulsions can be made. However, this region is also known for its rapid coalescence rate. Thus, a high enough stability can be attained only by shifting the formulation away from optimum as soon as the emulsion is made. Moreover, a rapid change in formulation through the three-phase region also results in a separation phenomenon that can be harnessed to produce ultra fine droplets.

The phase behavior of surfactant-oil-water systems and emulsion properties (type, droplet size and stability) are studied as a function of surfactant concentration (2 wt.% and 6 wt.%), for two different nonionic surfactants (polyoxyethylene tri-terbutyl ethers and sorbitan derivatives) with HLB ranging from 4 to 16. Kerosene and paraffin oil are used as oil phases. The transitional inversion form W/O to O/W is induced by a rapid cooling of the stirred systems from above to below the optimum temperature for three-phase behavior.

Miniemulsions are attained when the surfactant concentration is high enough, and when the temperature quenching span covers an appropriate range related to phase behavior.     

Microstructure of beta-lactoglobulin-stabilized emulsions containing non-ionic surfactant and excess free protein: influence of heating

The influence of the non-ionic surfactant Tween 20 on the microstructure of beta-lactoglobulin-stabilized emulsions with substantial excess free protein present was investigated via confocal microscopy. The separate distributions of oil droplets and protein were determined using two different fluorescent dyes. In the emulsion at ambient temperature the excess protein and protein-coated oil droplets were associated together in a reversibly flocculated state. The pore-size distribution of the initial flocculated emulsion was found to depend on the surfactant/protein ratio R, and at higher values of R the system became more inhomogeneous due to areas of local phase separation. Evidence for competitive displacement of protein from the oil-water interface by surfactant was obtained only on heating (from 25 to 85 degrees C) during the process of formation of a heat-set emulsion gel. By measuring fluorescence intensities of the protein dye inside and outside of the oil-droplet-rich areas, we have been able to quantify the evolving protein distribution during the thermal processing. The results are discussed in relation to previous work on the competitive adsorption of proteins and surfactants in emulsions and the effect of emulsion droplets on the rheology of heat-set protein gels.     

Highly Concentrated Emulsions: Physicochemical Principles of Formulation

This review deals with the preparation, stability, rheology and different applications of highly concentrated emulsions. These emulsions, which are known as high internal phase ratio emulsions (HIPRE), gel-emulsions, biliquid foams, etc., containing over 90% internal phase by volume, have a swollen micellar (L₁ or L₂) solution of nonionic or ionic surfactants as a continuous phase. These emulsions have the structure of biliquid foams and behave as gels since they present viscoelastic and plastic properties. The functional macroscopic properties of gel-emulsions are dependent on the structural parameters of the microemulsion continuous phase as well as of the interfacial properties (interfacial tension, bending modules, spontaneous curvature) of surfactant monolayers. The depletion interaction between emulsion droplets due to the non-compensated osmotic pressure of micelles is revealed as a main factor, along with surface forces, which determine the aggregative stability and the rheological properties of these emulsions. The effect of electrolyte and surfactant concentration, temperature, as well as other physicochemical parameters on the fiocculation threshold, stability, and yielding properties of highly concentrated emulsions is explained by the effect of these parameters on the critical micelle concentration (CMC) and the aggregation number of surfactants, and, consequently, on the depletion interaction. The thermodynamic theory of adhesion of fluid droplets in micellar solution and the suggested model of elasticity of gel-emulsions permit to explain the effect of mentioned physicochemical parameters on the elasticity modulus, the plastic strength and the linear deformation of these emulsions. A novel mechanism for the spontaneous formation of gel-emulsions by the phase inversion temperature (PIT) route is suggested, allows the selection of ternary systems able to yield these emulsions, and explains how the droplet size can be controlled during the PIT process. An original model for liquid film rupture is also suggested, and allows the prediction of the effect of structural parameters of micellar solutions and the interfacial properties of surfactant monolayers on the stability of gel-emulsions.     

Evaluation of emulsion stability by thermogravimetric analysis (tg)

A rapid and simplified method for the determination of phase inversion temperature (PIT) and the stability of oil in water emulsions, stabilized by nonionic emulsifiers, is described. The method is based on the use of any thermogravimetric apparatus from which the rate of loss of water can be measured as a function of linear increase in the emulsion temperature. A DTG peak is obtained at the PIT: the emulsion in which the lowest PIT is observed is also the less stable one.