在改进的Ni基催化剂上的甲烷部分氧化制合成气反应

 本文采用高温分解和焙烧硝酸盐的方法合成了一系列Ni基六铝酸盐催化剂BaNiyAl12-yO19-δ (y=0.1、0.3、0.6、0.9和1.0)，并对它们在甲烷部分氧化制合成气反应中的催化性能、催化剂表面积碳及活性组分Ni流失等情况进行了考察。结果表明，该催化剂对甲烷部分氧化制合成气反应具有较好的催化活性，在850 ℃，甲烷转化率和CO选择性分别可达92%和95%。并且催化剂BaNiyAl12-yO19-δ (y=0.3)在100小时的POM反应后，催化剂表面积碳很少，积碳量仅为样品净重的0.8%，特别是100小时反应后，催化剂表面活性组分Ni没有发生流失。这种低积碳量和无活性组分Ni流失与催化剂结构中Ni与相邻原子间的强相互作用有关。     

Cr2O3催化剂上甲烷部分氧化制备合成气

分别采用柠檬酸络合法和直接分解法制备了Cr2O3催化剂, 采用XRD, BET, TPR, XPS, TEM和TGA表征了催化剂的物理化学性质, 在常压固定床石英管(内径5 mm)反应器中考察了Cr2O3催化剂对甲烷部分氧化反应的催化性能. 在500~750 ℃, V(CH4)∶V(O2)=2, 空速12×104 h-1的条件下, O2几乎完全转化, CH4转化率及H2和CO选择性随着温度的升高而增加. 700 ℃下CH4转化率及H2, CO选择性随着空速(6.0×104~24×104 h-1)的升高而增加. 在500 h稳定性实验中, 随着反应时间的延长, CH4转化率及H2, CO选择性缓慢下降, XRD, TEM和BET结果表明, 催化剂的活性下降与烧结和团聚有关, TGA分析表明催化剂具有良好的抗积炭性. 通过CH4脉冲反应, 推测在反应过程中CO, H2, CO2和H2O是直接生成的.     

钙钛矿型复合氧化物在甲烷部分氧化反应中催化性能的研究

自 1 990年以来 ,由甲烷部分氧化制合成气 ( POM)的反应作为对传统甲烷水蒸气重整反应的一个重大改进而受到高度重视 [1] .目前 ,在 POM反应中 ,研究较多的催化剂体系大致可分为贵金属 ( Pt,Pd,Rh,Ru及 Ir) [2 ,3] 以及以 Ni和 Co为主的 B族过渡金属催化剂[4～ 6 ] .最近 ,Hayakawa等 [7,8] 报道了具有钙钛矿结构的复合氧化物 Ca1- x Srx Ti1- y My O3-δ( M=Cr,Fe,Co或 Ni)在甲烷部分氧化制合成气反应中具有一定的催化活性 .本文以本组开发的钙钛矿型复合氧化物 Ba0 .5Sr0 .5Co0 .8Fe0 .2 O3-δ(简称BSCFO)和 Ba0 .5Sr0 .5…     

甲烷部分氧化制合成气的研究

考察了镍基和钴基催化剂催化甲烷在自放热条件下部分氧化制合成气。结果表明，在较高的空速条件下，反应一旦引发即可停止供热，仅靠反应自身放出的热量就能维持反应的继续进行：Ｎｉ／Ｌａ２Ｏ３催化剂中的镍负载量大于１０％后，镍负载量对催化活性无明显的影响；ＣＨ４的转化率及Ｈ２和ＣＯ的选择性均随空速和反应温度的增加而提高；对Ｎｉ／ＺｒＯ２和Ｃｏ／ＺｒＯ２催化剂，反应进行到６－１２ｈ时，ＣＨ４转化经最高；但对Ｎｉ     

压力对甲烷部分氧化制合成气反应的影响

甲烷部分氧化制合成气是近年来催化界关心的课题之一，文献报导的工作多在常压下进行［１～４］．然而天然气和纯氧都有一定压力，且以合成气为原料的后续过程通常都在较高压力下操作，从节能的角度出发，研究加压甲烷部分氧化制合成气具有重要的实际意义［１，２］．我们...     

甲烷和空气部分氧化制合成气

使用空气做氧化剂,可减轻甲烷部分氧化制合成气反应中催化剂床层的“热点”问题,而且可大大降低加压反应条件下反应爆炸的危险性,因此易于工业化,对国内外在这一领域的研究总结表明,以空气与甲烷部分氧化制合成气在理论和反应条件上都是可行的,但忖用于空气来转化CH4的抗高温烧结和抗结炭性能好的催化剂有待进一步研究和开发,参考文献10篇。     

流化床反应器中甲烷部分氧化制合成气

Most previous studies on the partial oxidation of methane (POM) have used either fixed beds or monolith catalysts[1].     

Ni系列催化剂上甲烷直接氧化制合成气

采用固定床流动反应装置，考察负载型Ｎｉ系列催化剂在甲烷直接氧化制合成气反应上的催化活性．空速为５．０×１０５ｈ－１，ＣＨ４／Ｏ２＝２条件下，不同Ｎｉ含量的催化剂中，１５％Ｎｉ／Ａｌ２Ｏ３活性较好．利用ＴＰＤ和ＸＲＤ技术将催化剂引发温度与催化剂组成进行关联，并在７００℃下考察空速对催化性能的影响．随着空速的增加，ＣＨ４的转化率增加，７．０×１０５ｈ－１时达到最大，与此同时，ＣＯ的选择性一直增加．实验结果说明在非平衡体系中，ＣＯ和Ｈ２是由ＣＨ４直接转化而来，ＣＯ２是ＣＯ深度氧化的产物，在此基础上对催化剂过程的机理作了初步的探讨．     

Studies on the Performance and Structure of Supported Catalysts for the Partial

The catalytic properties of several supported metal catalysts on different carriers were studied in the partial oxidation of methane (POM) to syngas. In our experiment, supported noble metal catalysts exhibited better performance than the other supported transition metal catalysts. The catalyst performances were significantly influenced by the d-electron configuration of the active metal components and the dispersion of active metal components on the support. A catalyst with a moderate number of unpaired electrons in the d-orbital of the active metal support without obvious acidity or redox activity (e.g. MgO) was suitable for POM performance. The Rh/SiO2 catalyst was the best in the POM reaction, among those investigated. Reaction conditions apparently also affected the POM performance of the catalyst. The conversion of methane and the selectivity for CO increased with the reaction temperature, and a high CH4/O2 ratio was not beneficial for POM performance.     

Studies on the Performance and Structure of Supported Catalysts for the Partial Oxidation of Methane to Syngas

The catalytic properties of several supported metal catalysts on different carriers were studied in the partial oxidation of methane (POM) to syngas. In our experiment, supported noble metal catalysts exhibited better performance than the other supported transition metal catalysts. The catalyst performances were significantly influenced by the d-electron configuration of the active metal components and the dispersion of active metal components on the support. A catalyst with a moderate number of unpaired electrons in the d-orbital of the active metal support without obvious acidity or redox activity (e.g. MgO) was suitable for POM performance. The Rh/SiO2 catalyst was the best in the POM reaction, among those investigated. Reaction conditions apparently also affected the POM performance of the catalyst. The conversion of methane and the selectivity for CO increased with the reaction temperature, and a high CH4/O2 ratio was not beneficial for POM performance.     

甲烷部分氧化制合成气在Ni,Cu及Ni-Cu合金上的DFT研究

基于密度泛函理论(DFT)的DMol3量子力学计算程序模块应用于合金体系,通过与N i(111)和Cu(111)的比较,研究了N iCu(111)上甲烷部分氧化制合成气的活性.计算结果显示,Cu的加入导致H2在N iCu(111)的脱附能垒低于H2在N i(111)上的脱附能垒,CO的吸附热变化不大.此外,还考察了甲烷解离的过程,发现Cu的加入对速控步骤的活化能影响不大.     

自放热条件下甲烷部分氧化制合成气

天然气组成的９０％以上是甲烷．目前由天然气制合成气的主要方法是水蒸汽重整法,这种方法投资大、设备复杂、能耗高、生产的合成气不适于直接用来合成甲醇和烃类等．甲烷部分氧化可直接制得Ｈ２与ＣＯ摩尔比为２的合成气,这是一个温和的放热过程、具有大空速和低温等优...     

Partial Oxidation of Ethane to Syngas over Supported Metal Catalysts

The reaction performance for C₂H₆-O₂ to syngas over different supported metal catalysts was investigated in a flow-reactor. The activated behavior of ethane is different from that of methane over the supported nickel catalysts. Although there may exist a gas phase reaction at high temperatures, over a Ni (or Rh)/-Al₂O₃ catalyst, the partial oxidation of ethane to syngas is a heterogeneous process, while over a Pt (or Pd)/-Al₂O₃ catalyst, it may be a homo-heterogeneous process. The Ni/-Al₂O₃ and Rh/-Al₂O₃ catalysts are suitable for partial oxidation of ethane to syngas at high temperatures.     

用于部分氧化甲烷制合成气的铈基氧载体性能表征

将稀土氧化物CeO2中的晶格氧用于熔融盐体系下甲烷部分氧化制取合成气的新方法,采用浸渍法制备了负载型铈基氧载体,利用XRD、O2-TPD、H2-TPR分析手段对氧载体进行了表征.在甲烷气氛下进行了CeO2的热重实验.在熔融盐反应器中分别考察了添加1%TiO2和MgO两种不同助剂对10?O2-Al2O3负载型氧载体反应性能的影响.结果表明,CeO2容易失去晶格氧被还原为低价态铈的氧化物,同时把甲烷部分氧化成H2和CO,有着良好的循环使用性能.助剂的添加能够明显改善氧载体的反应活性,其中以添加MgO比较理想.     

Pt/MgO 催化剂上甲烷部分氧化制合成气反应

用浸渍法制备了Pt/MgO催化剂,并采用X射线衍射、X射线光电子能谱、透射电子显微镜和程序升温表面反应等技术对催化剂进行了表征.考察了催化剂对甲烷部分氧化制合成气反应的催化性能.结果表明,Pt/MgO催化剂具有较高的催化活性和选择性,甲烷转化率与合成气选择性在120 h内保持稳定.以金属状态存在的Pt对甲烷分解具有较高的活性,从而使催化剂对甲烷部分氧化反应具有较高的催化活性.活性组分Pt的存在状态和分散状态非常稳定,而Pt/MgO催化剂具有较强的抗积碳能力,使得催化剂在甲烷部分氧化制合成气反应中具有较高的稳定性.     

不同Ni前驱物对Ni催化剂甲烷部分氧化制合成气的影响

考察了由硝酸镍,醋酸镍和氯化镍为前驱物制备的催化剂（分别记为Ｎｉ－Ｎ,Ｎｉ－Ａｃ和Ｎｉ－Ｃｌ）对催化甲烷部分氧化反应的影响,并结合和ＴＧ等手段对催化剂进行了表征,结果表明,Ｎｉ－Ａｃ催化剂在６２５℃就能自引发甲烷部分氧化反应,而在Ｎｉ－Ｎ和Ｎｉ－Ｃｌ催化剂上,直到７５０℃甲烷部分氧化反应仍未能引发,三种催化剂上的反应结果表明,Ｎｉ－Ｎ和Ｎｉ－Ｃｌ的催化活性较低。９００℃下的高温反应结果表明,Ｎｉ－     

A Study of Carbon Deposition on Catalysts During the Catalytic Partial Oxidation of Methane to Syngas in a Fluidized bed

The deposition of carbon on catalysts during the partial oxidation of methane to syngas has been investigated in a fluidized bed. It was found that the relative rate of carbon deposition follows the order Ni>>Pd>Pt, Rh. Although the rate of carbon deposition in the fluidized bed was much lower than that in the fixed bed, carbon deposition could still be detected in the fluidized bed if a CH₄ /O₂ ratio in greater than 2.3 was used.     

The Order of Product Formation in the Partial Oxidation of Methane to Syngas

The partial oxidation of methane to syngas is studied in the presence of Pt- and Ni-containing catalysts. The process kinetics does not provide unequivocal information on the order of formation of products (including carbon oxides) when either methane–oxygen or methane–oxygen–CO₂ mixtures are used. Experiments with ¹³C-labeled carbon dioxide added show the difference in the behavior of the catalysts. In the presence of Pt/ZrO₂, there is no noticeable transfer of the isotopic label to the CO molecules. On the nickel catalyst, ¹³CO is formed in substantial amounts, which can probably be explained by the redox reaction of ¹³CO₂ with metallic nickel under oxygen-free conditions behind the zone of the main reaction of methane oxidation.     

Ni/TiO2 Catalyst for Partial Oxidation of Methane to Syngas

Ni/TiO₂ catalyst was firstly used for the partial oxidation of methane to produce synthesis gas. The reaction was carried out in a fixed-bed continuous flow quartz reactor at atmospheric pressure. The flow rate was regulated by a mass controller with a space velocity of 1.5×10⁵ h^-1 and a CH₄/O₂ molar ratio of 2/1. Prior to the introduction of feed gas, the Ni/TiO₂ catalyst was activated in flowing H₂ at 700℃ for 30 min. TiO₂ is known to be a poor support for partial oxidation because which can easily result in complete oxidation. But at 700℃, Ni/TiO₂ catalyst exhibited a better performance than Ni/SiO₂ and Ni/ZrO₂. The conversion of methane was 81.5, and the selectivity of hydrogen and carbon monoxide were 93.4 and 89.4 respectively. After 6h of continuous reaction, the conversion of methane descended a little and then remained a steady yield on the whole,but the selectivity of H₂ and CO gradually declined, as far as to a constant. The selectivity of H₂ was always higher than that of CO and the ratio of H₂/CO wouldn't change with the increasing of reaction time.     

Rh／SiO2催化剂上甲烷部分氧化制合成气反应

 利用程序升温脱附、程序升温还原、程序升温表面反应、程序升温反应和化学捕获反应等手段，对Rh／SiO2催化剂上甲烷部分氧化制合成气反应进行了研究．结果表明，Rh／SiO2催化剂上甲烷部分氧化制合成气机理属于热解－氧化反应机理．甲烷首先在催化剂上发生解离吸附，产生具有不同H／C比的化学吸附物种CHx（x＝1～3）．其中，具有较高H／C比的CHx可能是甲烷部分氧化反应的活性物种，而具有较低H／C比的CHx可能是催化剂上积碳并导致催化剂失活的来源．活性物种CHx在活性氧物种的作用下，生成含氧中间体物种CHxO或继续脱氢．含氧中间体物种进一步分解，即生成CO和H2；CO2也可由CHx或CHxO物种进一步氧 化生成．