等离子体引入方式对强化制备二氧化碳重整甲烷反应的Ni/γ-Al2O3催化剂的影响

采用等离子体技术强化制备了Ni/γ-Al2O3催化剂, 以CO2重整CH4为模型反应考察了等离子体引入方式对催化剂性能的影响, 并采用H2-TPR, BET, CO2-TPD, XRD, CO2-TPSR, TGA及XPS技术对催化剂进行了表征. 研究结果表明, 与常规焙烧的催化剂相比, 在氢气还原过程前引入氮气等离子体处理能有效提高催化剂的低温反应活性. N2气等离子体处理使前驱体中的硝酸盐能在温和条件下分解, 并使催化剂具有较强的还原能力和较大的比表面积. 先进行N2气等离子体处理再进行H2气还原的催化剂, 其活性组分的分散度显著提高, 对CO2的吸附量也明显增加, 并且反应后催化剂上的积炭量比常规催化剂上的显著降低, 形成比较单一的碳物种.     

ZnO对Au-Pd/CeO_2催化剂甲醇部分氧化制氢性能的影响

采用沉积沉淀法制备了Au-Pd双金属催化剂, 研究了ZnO对Au-Pd/CeO_2催化剂甲醇部分氧化性能的影响, 并运用N_2吸附、 XRD、 UV-Vis、 TPR、 H2-TPD和CO-IR等手段对催化剂进行了表征. 结果表明, ZnO的引入减少了Pd活性中心, 降低了催化剂的活性, 但提高了催化剂H2选择性和降低了CO选择性. Au-Pd/ZnO-CeO_2催化剂的TPR表明, 在约200℃时开始有部分ZnO被还原, CO-IR显示CO吸收峰移向低频, 这些结果表明Au-Pd/ZnO-CeO_2催化剂中Pd和Zn之间发生了相互作用. Pd和Zn之间相互作用抑制了Pd的甲醇分解活性, 有利于H2和CO_2的生成, 使Au-Pd/ZnO-CeO_2催化剂表现出较高的H2选择性和较低的CO选择性.     

Cu/Zn、Cu/Zn/Ni催化剂甲醇部分氧化制氢

研究了甲醇在Cu/Zn及Cu/Zn/Ni催化剂上部分氧化热耦合裂解制氢的反应,系 统地考察了不同O2/CH3OH比及反应温度下催化剂性能.当O2/CH3OH=0.2时,催化剂的性能最 佳.在同样条件下, Cu/Zn催化剂对CO的选择性较Cu/Zn/Ni催化剂低,更具优势. Cu/Zn催化 剂用于甲醇部分氧化反应时,甲醇转化率在150 h寿命实验中基本保持在90％左右. XRD谱图 表明Cu/Zn合金的生成是导致Cu/Zn系催化剂在甲醇裂解反应中快速失活的主要原因,而在部 分氧化反应中, O2的存在可抑制Cu/Zn合金的生成,使Cu/Zn催化剂表现出高度的稳定性.     

Comparative theoretical study of formaldehyde decomposition on PdZn, Cu, and Pd surfaces

Methanol steam reforming, catalyzed by Pd/ZnO (PdZn alloy), is a potential source of hydrogen for on-board fuel cells. CO has been reported to be a minor side product of methanol decomposition that occurs in parallel to methanol steam reforming on PdZn catalysts. However, fuel cells currently used in vehicles are very sensitive to CO poisoning. To contribute to the understanding of pertinent reaction mechanisms, we employed density functional slab model calculations to study the decomposition of formaldehyde, a key intermediate in methanol decomposition and steam reforming reactions, on planar surfaces of Pd, Cu, and PdZn as well as on a stepped surface of PdZn. The calculated activation energies indicate that dehydrogenation of formaldehyde is favorable on Pd(111), but unfavorable on Cu(111) and PdZn(111). On the stepped PdZn(221) surface, the dehydrogenation process was calculated to be more competitive to formaldehyde desorption than on PdZn(111). Thus, we ascribe the experimentally observed small amount of CO, formed during steam reforming of methanol on the Pd/ZnO catalyst, to occur at metallic Pd species of the catalyst or at defect sites of PdZn alloy.     

复合床合成低碳醇的研究

采用了三种不同的合成醇催化剂分别作为第一段催化床层,以ＺｎＯ／Ｃｒ２Ｏ３催化剂作为第二段催化床层,研究了复合催化剂床对合成低碳醇反应行为的影响。结果表明,采用复合床层技术可以提高反应产物中低碳醇的选择性,但是烃类的转化率增加,液收减小。同时发现,第一段催化床层的反应产物分布与第二段催化床层的反应条件直接影响最终的反应结果。第一段催化剂床层中ＣＯ的转化率或甲醇的选择性过高都不利于提高反应产物中低碳醇的选择性     

二甲醚水蒸气重整制氢的ZSM-5和Cu-Zn的复合催化体系

二甲醚水蒸气重整制氢反应是燃料电池理想的供氢方式之一.探讨了二甲醚水蒸气重整过程中的反应与反应、反应与传热的耦合协同效应.采用二甲醚水解催化剂ZSM-5(硅铝比为25)和甲醇水蒸气重整催化剂(Cu-Zn系列及商用Cu-Zn-Al催化剂)混合制得二甲醚水蒸气重整的复合催化剂.在固定床反应装置中评价了催化剂活性并对催化剂进行了透射电镜、X射线衍射及N2吸附表征.结果表明,复合催化剂的活性除了受催化剂组成和铜含量的影响外,还与Al和Zr的量有关.在Cu:Zn摩尔比为60:30时,Al和Zr的同时加入使催化剂中Cu晶粒分散最好,催化剂具有较高的低温活性,二甲醚在空速为4 922 ml/(g·h)和260℃下的转化率达到72%.     

CO2／CH4重整镍基催化剂制备与性能的关系

一般浸渍法与真空浸渍法的比较说明,真空浸渍制备的催化剂,其表面具有较多的Ｎｉ原子,催化活性较高,现场ＴＰＯ实验表明,ＣＯ岐化的积炭量大于ＣＨ４解离的积炭量。从而提出镍基催化剂的积炭主要来自反应生成气ＣＯ的岐化。     

陈化时间对CuO/ZnO/CeO2/ZrO2甲醇水蒸气重整制氢催化剂性能的影响

采用共沉淀法制备了CuO/ZnO/CeO₂/ZrO₂甲醇水蒸气重整催化剂,探讨了陈化时间对催化剂性能的影响.结果发现,延长陈化时间能增加催化剂的表面铜原子数和改善催化剂的还原性能,但与此同时也降低了催化剂的储放氧性能.延长陈化时间,CuO/ZnO/CeO₂/ZrO₂催化剂的氢产率随表面铜原子数的增加而成线性增长.另一方面,重整尾气中的CO含量也随着储放氧能力的下降而增加.综合考虑产氢率和重整尾气中CO含量,最佳陈化时间为2h,此时,CuO/ZnO/CeO₂/ZrO₂催化剂表现出了最佳性能.     

甲醇水蒸气重整制氢Cu/ZnO/Al2O3催化剂的研究

燃料电池作为一种无污染、高效率的能源引起世界各大汽车公司的广泛关注[1,2]。用于燃料电池的燃料目前研究较多的是氢气,用氢气作燃料存在储存、安全、运输等问题,寻求合适贮氢方法或替代燃料,实现车载制氢是解决问题的办法。甲醇作为液体燃料,因具有高能量密度,低碳含量,以及运输和贮存等优势成为车载制氢的理想燃料,甲醇水蒸气重整制氢反应也成为研究的热点[3～10]。车载制氢对甲醇水蒸气重整制氢反应体系中的产氢速率,氢气和CO的含量都有一定的要求。尤其对CO含量要求更为苛刻,因CO易引起燃料电池阳极催化剂中毒[11,12]。因此,开…     

CeO_2改性Cu/Zn-Al水滑石衍生催化剂对甲醇水蒸气重整制氢性能的影响

采用原位合成法在γ-Al2O3表面合成了锌铝水滑石,再采用顺次浸渍法制备了Ce/Cu/Zn-Al催化材料;将其应用于甲醇水蒸气重整制氢,探讨了Ce含量对Cu/Zn-Al催化剂催化性能的影响.催化剂表征结果表明,CeO_2的引入改善了活性组分铜的分散度、铜的比表面积以及催化剂的氧化还原性质,进而提高了催化剂的催化活性和产氢率.当Ce含量为4%时,催化剂活性最佳,在250℃时,甲醇转化率达到100%,CO摩尔分数为0.39%,与Cu/Zn-Al催化剂相比,甲醇转化率提高了近40%.     

固相法合成铜铝尖晶石催化甲醇重整反应

以氢氧化铜和拟薄水铝石为原料(Cu/Al物质的量比为1/2),采用固相法经过不同温度焙烧后获得了一系列Cu-Al氧化物催化剂.当焙烧温度由500 ℃提高到900 ℃时,催化剂的主要铜物种由CuO渐变为CuAl₂O₄,比表面积由75.0 m²/g降低至16.6 m²/g.在甲醇重整反应过程中,以CuAl₂O₄为主要成分且具有较高比表面积的催化剂表现了优异的催化性能.另外,以CuAl₂O₄为主要成分的催化剂不经过预还原处理时,在反应过程中同时存在活性铜的释放和烧结,其催化活性呈现先增加后降低的趋势.在本研究催化剂制备条件下,优选800 ℃焙烧的催化剂,其催化性能优于商业Cu-Zn-Al催化剂,且具有可再生性.当催化剂不经过预还原处理时,在水醇物质的量比为1、240 ℃、1.01×10⁶ Pa、质量空速为1.75 h^-1的条件下,甲醇起始转化率为55.2%;反应进行288.3 h时,甲醇转化率升高至79.3%;反应继续运行至1 000.5 h时,甲醇转化率降低至63.9%.     

前驱体和沉淀剂浓度对CuO/ZnO/CeO2-ZrO2甲醇水蒸气重整制氢催化剂性能的影响

采用共沉淀法制备了CuO/ZnO/CeO₂-ZrO₂甲醇水蒸气重整制氢催化剂,探讨了前驱体和沉淀剂浓度对催化剂性能的影响,并采用BET、XRD、H₂-TPR和XPS等手段对催化剂进行了表征。结果表明,前驱体和沉淀剂浓度对催化剂的结构和性能影响很大,当前驱体浓度为0.1mol/L,沉淀剂浓度为0.5mol/L时,所得催化剂CO选择性最小,催化活性最佳。在360h稳定实验中,甲醇最高转化率达100%,重整尾气中H₂含量保持在74.5%以上,CO含量低于0.8%,催化剂稳定性良好。     

The origin of the high performance of tungsten carbides/carbon nanotubes supported Pt catalysts for methanol electrooxidation

The Pt supported on WC modified MWCNT catalysts (PtWC/MWCNT) were synthesized by the combination of organic colloidal and intermittent microwave heating (IMH) methods for the first. The results proved the better performance of the PtWC/MWCNT catalyst than that of Pt/C for methanol oxidation in terms of the onset potential and peak current density. The synergistic effect between Pt nanoparticles and WC and the structure effect of the MWCNTs could be the reasons to result in the high activity. The CO stripping test provided the evidence that the onset potential shift for methanol oxidation is consistent with the reduction in the overpotential for the CO oxidation on PtWC/MWCNT catalyst. Therefore, the mechanism of the high performance for methanol oxidation on PtWC/MWCNT catalyst is probably the easier oxidation of CO-like species which cause high overpotential for further oxidation of methanol.     

STUDIES ON PREPARATION OF GAS FOR METHANOL SYNTHESIS BY METHANE REFORMING WITH STEAM AND CO_2 Ⅱ.ACTIVITY AND STABILITY OF SUPPORTED NICKEL CATALYSTS

lntroductionMethanolissynthesizedbyblendgasofCOandH2.FeedstockgasformethanolsynthesismustbeinlinewiththefollowingstoichiometricrelationtR=(H2-Co2)/(Co CO2)52Inaddition,thecontentofCo2shouldbelowerthan8%ll1.MethanereformingwithsteamandCO2canproducethequalifiedsynthesisgasformethanolsynthesisinindustry.ComParedwithtndtionalsteaInrefotheng,thefeedstocksynthsisgasproducedbymethanreformingwithsteamandCO2docsnotneedseparaingandcanbedirectlyusedinmethanolsynthesis.Therefore,thecostofmethanolca…     

Rh doping effect on coking resistance of Ni/SBA-15 catalysts in dry reforming of methane

A series of SBA-15 supported bimetallic Rh–Ni catalysts with different weight ratio of Rh/Ni in the range of 0–0.04 were prepared for carbon dioxide reforming of methane. The doping effect of Rh on catalytic activity as well as carbon accumulation and removal over the catalysts was studied. The characterization results indicated that the addition of a small amount of Rh promoted the reducibility of Ni particles and decreased the Ni particle size. During the dry reforming reaction, the carbon deposition was originated from CH4 decomposition and CO disproportionation. The Rh–Ni catalyst with small metallic particle size inhibited the carbon formation and exhibited high efficiency in the removal of coke. In comparison with bare Ni-based catalyst, the Rh–Ni bimetallic catalysts showed high activity and stability in the dry reforming of methane.     

CuO-ZnO-ZrO2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整（SRM）反应进行程序升温脱附（TPD）和程序升温表面反应（TPSR）研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO、CO2和H2.     

甲烷在Ni/TiO2催化剂表面的活化

考察了Ni/TiO2催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以TiO2为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对H2的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性.采用脉冲-质谱在线分析等技术,在无气相氧条件下向Ni/TiO2催化剂脉冲CH4,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关.CH4与Ni/TiO2催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ni/TiO2催化剂具有良好的反应活性和抗积碳性能.     

改进型铜基甲醇含成催化剂NC208的活性相谱学表征

利用XRD和FTIR等谱学方法,对改进型铜基联醇催化剂NC208和工业催化剂C207的活性相进行了谱学表征.实验结果表明,联醇铜基甲醇含成催化剂的活性中心可能是Cu_x⁰-Cu⁺-O-Zn²⁺/Al₂O₃-MOx添加少量金属氧化物助剂的改进型NC208催化剂工作表面Cu⁺活性位的浓度比Cu－Zn－Al三组份工业催化剂C207高;NC208催化剂能维持工作表面具有较大的Cu⁺/Cu0比,即维持较高的Cu＋价态稳定性,这与该催化剂的活性和热稳定性明显优于C207有着密切联系.     

CuO-ZnO-ZrO_2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整(SRM)反应进行程序升温脱附(TPD)和程序升温表面反应(TPSR)研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO、CO2和H2.     

Hierarchical multiscale mechanism development for methane partial oxidation and reforming and for thermal decomposition of oxygenates on Rh

A thermodynamically consistent C1 microkinetic model is developed for methane partial oxidation and reforming and for oxygenate (methanol and formaldehyde) decomposition on Rh via a hierarchical multiscale methodology. Sensitivity analysis is employed to identify the important parameters of the semiempirical unity bond index quadratic exponential potential (UBI-QEP) method and these parameters are refined using quantum mechanical density functional theory. With adjustment of only two pre-exponentials in the CH4 oxidation subset, the C1 mechanism captures a multitude of catalytic partial oxidation (CPOX) and reforming experimental data as well as thermal decomposition of methanol and formaldehyde. We validate the microkinetic model against high-pressure, spatially resolved CPOX experimental data. Distinct oxidation and reforming zones are predicted to exist, in agreement with experiments, suggesting that hydrogen is produced from reforming of methane by H2O formed in the oxidation zone. CO is produced catalytically by partial oxidation up to moderately high pressures, with water-gas shift taking place in the gas-phase at sufficiently high pressures resulting in reduction of CO selectivity.