Nanoscale Pt(0) particles prepared in imidazolium room temperature ionic liquids: synthesis from an organometallic precursor,characterization, and catalytic properties in hydrogenation reactions

The reaction of Pt(2)(dba)(3) (dba = bis-dibenzylidene acetone) dispersed in room temperature 1-n-butyl-3-methylimidazolium (BMI) hexafluorophosphate ionic liquid with molecular hydrogen (4 atm) at 75 degrees C leads to stable and isolable nanometric Pt(0) particles. The X-ray diffraction analysis (XRD) of the material indicated that it is constituted of Pt(0). Transmission electron microscopy (TEM) analysis of the particles dispersed in the ionic liquid shows the formation of [Pt(0)](n) nanoparticles of 2.0-2.5 nm in diameter. A detailed examination of the nanoparticles imbibed in the ionic liquid and their environment shows an interaction of the BMI.PF(6) ionic liquid with the Pt(0) nanoparticles. The isolated [Pt(0)](n) nanoparticles can be redispersed in the ionic liquid or in acetone or used in solventless conditions for liquid-liquid biphasic, homogeneous, or heterogeneous hydrogenation of alkenes and arenes under mild reaction conditions (75 degrees C and 4 atm). The recovered platinum nanoparticles can be reused as a solid or redispersed in the ionic liquid several times without any significant loss in catalytic activity.     

Charge Transport through Molecular Rods with Reduced π‐Conjugation

A series of oligophenylene rods of increasing lengths is synthesized to investigate the charge‐transport mechanisms. Methyl groups are attached to the phenyl rings to weaken the electronic overlap of the π‐subsystems along the molecular backbones. Out‐of‐plane rotation of the phenyl rings is confirmed in the solid state by means of X‐ray analysis and in solution by using UV/Vis spectroscopy. The influence of the reduced π‐conjugation on the resonant charge transport is studied at the single‐molecule level by using the mechanically controllable break‐junction technique. Experiments are performed under ultra‐high‐vacuum conditions at low temperature (50 K). A linear increase of the conductance gap with increasing number of phenyl rings (from 260 meV for one ring to 580 meV for four rings) is revealed. In addition, the absolute conductance of the first resonant peaks does not depend on the length of the molecular wire. Resonant transport through the first molecular orbital is found to be dominated by charge‐carrier injection into the molecule, rather than by the intrinsic resistance of the molecular wire length.     

The use of imidazolium ionic liquids for the formation and stabilization of ir0 and rh0 nanoparticles: efficient catalysts for the hydrogenation of arenes

Stable transition-metal nanoparticles of the type [M(0)](n) are easily accessible through the reduction of Ir(I) or Rh(III) compounds dissolved in "dry" 1-n-butyl-3-methylimidazolium hexafluorophosphate ionic liquid by molecular hydrogen. The formation of these [M(0)](n) nanoparticles is straightforward; they are prepared in dry ionic liquid whereas the presence of the water causes the partial decomposition of ionic liquid with the formation of phosphates, HF and transition-metal fluorides. Transmission electron microscopy (TEM) observations and X-ray diffraction analysis (XRD) show the formation of [Ir(0)](n) and [Rh(0)](n) nanoparticles with 2.0-2.5 nm in diameter. The isolated [M(0)](n) nanoparticles can be redispersed in the ionic liquid, in acetone or used in solventless conditions for the liquid-liquid biphasic, homogeneous or heterogeneous hydrogenation of arenes under mild reaction conditions (75 degrees C and 4 atm). The recovered iridium nanoparticles can be reused several times without any significant loss in catalytic activity. Unprecedented total turnover numbers (TTO) of 3509 in 32 h, for arene hydrogenation by nanoparticles catalysts, have been achieved in the reduction of benzene by the [Ir(0)](n) in solventless conditions. Contrarily, the recovered Rh(0) nanoparticles show significant agglomeration into large particles with a loss of catalytic activity. The hydrogenation of arenes containing functional groups, such as anisole, by the [Ir(0)](n) nanoparticles occurs with concomitant hydrogenolysis of the C-O bond, suggesting that these nanoparticles behave as "heterogeneous catalysts" rather than "homogeneous catalysts".     

Correlations between molecular structure and single-junction conductance: a case study with oligo(phenylene-ethynylene)-type wires

The charge transport characteristics of 11 tailor-made dithiol-terminated oligo(phenylene-ethynylene) (OPE)-type molecules attached to two gold electrodes were studied at a solid/liquid interface in a combined approach using an STM break junction (STM-BJ) and a mechanically controlled break junction (MCBJ) setup. We designed and characterized 11 structurally distinct dithiol-terminated OPE-type molecules with varied length and HOMO/LUMO energy. Increase of the molecular length and/or of the HOMO-LUMO gap leads to a decrease of the single-junction conductance of the linearly conjugate acenes. The experimental data and simulations suggest a nonresonant tunneling mechanism involving hole transport through the molecular HOMO, with a decay constant β = 3.4 ± 0.1 nm(-1) and a contact resistance R(c) = 40 kΩ per Au-S bond. The introduction of a cross-conjugated anthraquinone or a dihydroanthracene central unit results in lower conductance values, which are attributed to a destructive quantum interference phenomenon for the former and a broken π-conjugation for the latter. The statistical analysis of conductance-distance and current-voltage traces revealed details of evolution and breaking of molecular junctions. In particular, we explored the effect of stretching rate and junction stability. We compare our experimental results with DFT calculations using the ab initio code SMEAGOL and discuss how the structure of the molecular wires affects the conductance values.     

Thermoelectrics in an array of molecular junctions

The room temperature thermoelectric properties of a three-dimensional array of molecular junctions are calculated. The array is composed of n-doped silicon nanoparticles where the surfaces are partially covered with polar molecules and the nanoparticles are bridged by trans-polyacetylene molecules. The role of the polar molecules is to reduce the band bending in the n-doped silicon nanoparticles and to shift the electronic resonances of the bridging molecules to the nanoparticle conduction band edges where the molecular resonances act as electron energy filters. The transmission coefficients of the bridging molecules that appear in the formulas for the Seebeck coefficient, the electrical conductance, and the electronic thermal conductance, are calculated using the nonequilibrium Green's function technique. A simple tight-binding Hamiltonian is used to describe the bridging molecules, and the self-energy term is calculated using the parabolic conduction band approximation. The dependencies of the thermoelectric properties of the molecular junctions on the silicon doping concentration and on the molecule-nanoparticle coupling are discussed. The maximal achievable thermoelectric figure of merit ZT of the array is estimated as a function of the phononic thermal conductance of the bridging molecules and the doping of the nanoparticles. The power factor of the array is also calculated. For sufficiently small phononic thermal conductances of the bridging molecules, very high ZT values are predicted.     

离子液体中氧化锰八面体分子筛催化醇的氧化

按文献方法制备了3种八面体MnO6分子筛催化剂K-OMS-2、H-K-OMS-2和Cu-OMS-2,用SEM和XRD测试技术表征了它们的结构和组成。 考察了这3种催化剂对用氧气选择性氧化醇为相应的醛或酮的催化作用,研究了采用不同OMS-2在离子液体[bmim]PF₆中反应时间和反应温度对催化反应的影响。 其中H-K-OMS-2对苄醇和烯丙醇氧化的转化率和选择性均超过90%。 催化剂和离子液体可分别用萃取法和减压蒸馏法从反应体系中回收,其中减压蒸馏法回收循环使用效果较好。     

Synthesis and characterization of Pt0 nanoparticles in imidazolium ionic liquids

The controlled decomposition of Pt2(dba)3 (dba = dibenzylideneacetone) dispersed in 1-n-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF4) and hexafluorophosphate (BMI.PF6) ionic liquids in the presence of cyclohexene by molecular hydrogen produces Pt0 nanoparticles. The formation of these nanoparticles follows the two-step [A --> B, A + B --> 2B (k1, k2)] autocatalytic mechanism. The catalytic activity in the hydrogenation of cyclohexene is influenced by the nature of the anion rather than the mean-diameter of the nanoparticles. Thus, higher catalytic activity was obtained with Pt0 dispersed in BMI.BF4 containing the less coordinating anion although these nanoparticles possess a larger mean diameter (3.4 nm) than those obtained in BMI.PF6 (2.3 nm). Similar mean diameter values were estimated from in situ XRD and SAXS. XPS analyses clearly show the interactions of the ionic liquid with the metal surface demonstrating the formation of an ionic liquid protective layer surrounding the platinum nanoparticles. SAXS analysis indicated the formation of a semi-organized ionic liquid layer surrounding the metal particles with an extended molecular length of around 2.8 nm in BMI.BF4 and 3.3 nm in BMI.PF6.     

Synthesis and characterization of catalytic iridium nanoparticles in imidazolium ionic liquids

The reduction of [Ir(cod)Cl](2) (cod=1,5-cyclooctadiene) dissolved in 1-n-butyl-3-methyl tetrafluoroborate, hexafluorophosphate and trifluoromethane sulphonate ionic liquids in the presence of 1-decene by molecular hydrogen produces Ir(0) nanoparticles. The formation of these nanoparticles follows the two-step [A-->B, A+B-->2B (k(1),k(2))] autocatalytic mechanism. The same mean diameter values of around 2-3 nm were estimated from in situ TEM and SAXS analyses of the Ir(0) nanoparticles dispersed in the ionic liquids and by XRD of the isolated material. XPS and EXAFS analyses clearly show the interactions of the ionic liquid with the metal surface demonstrating the formation of an ionic liquid protective layer surrounding the iridium nanoparticles. SAXS analysis indicated the formation of an ionic liquid layer surrounding the metal particles with an extended molecular length of around 2.8-4.0 nm depending on the type of the anion.     

Structure and diffusion of nanoparticle monolayers floating at liquid/vapor interfaces: a molecular dynamics study

Large-scale molecular dynamics simulations are used to simulate a layer of nanoparticles floating on the surface of a liquid. Both a low viscosity liquid, represented by Lennard-Jones monomers, and a high viscosity liquid, represented by linear homopolymers, are studied. The organization and diffusion of the nanoparticles are analyzed as the nanoparticle density and the contact angle between the nanoparticles and liquid are varied. When the interaction between the nanoparticles and liquid is reduced the contact angle increases and the nanoparticles ride higher on the liquid surface, which enables them to diffuse faster. In this case the short-range order is also reduced as seen in the pair correlation function. For the polymeric liquids, the out-of-layer fluctuation is suppressed and the short-range order is slightly enhanced. However, the diffusion becomes much slower and the mean square displacement even shows sub-linear time dependence at large times. The relation between diffusion coefficient and viscosity is found to deviate from that in bulk diffusion. Results are compared to simulations of the identical nanoparticles in 2-dimensions.     

Fullerene-based anchoring groups for molecular electronics

We present results on a new fullerene-based anchoring group for molecular electronics. Using lithographic mechanically controllable break junctions in vacuum we have determined the conductance and stability of single-molecule junctions of 1,4-bis(fullero[c]pyrrolidin-1-yl)benzene. The compound can be self-assembled from solution and has a low-bias conductance of 3 x 10(-4) G0. Compared to 1,4-benzenedithiol the fullerene-anchored molecule exhibits a considerably lower conductance spread. In addition, the signature of the new compound in histograms is more significant than that of 1,4-benzenediamine, probably owing to a more stable adsorption motif. Statistical analyses of the breaking of the junctions confirm the stability of the fullerene-gold bond.     

Tetrathiafulvalene-based molecular nanowires

A new molecular wire suitably functionalized with sulfur atoms at terminal positions and endowed with a central redox active TTF unit has been synthesized and inserted within two atomic-sized Au electrodes; electrical transport measurements have been performed in STM and MCBJ set-ups in a liquid environment and reveal conductance values around 10(-2) G0 for a single molecule.     

A molecular beam study of the evaporation of water from a liquid jet

A method to maintain a clean surface of a liquid in a high vacuum is described. Using a very thin and fast liquid jet it is not only possible to prevent freezing of the liquid but also to reduce the number of collisions between evaporating molecules to negligibly small values. Thus many of the standard, vacuum dependent, particle probing techniques for solid surfaces can be used for studies of rapidly vaporizing, high vapor pressure liquids. In a first molecular beam investigation we have used time-of-flight analysis to measure the velocity distribution of H₂O molecules vaporizing from thin jets of pure liquid water. The experiments were carried out for liquid jet diameters between 50 and 5 µm. In this range the expanding vapor is observed to undergo the transition to the collision-free molecular flow regime. From the measured velocity distributions the local surface temperature is determined to be less than 210 K. This appears to be the lowest temperature ever reported for supercooled liquid water.     

Self-assembled structure of nanoparticles at a liquid-liquid interface

Pickering emulsions are used as a template to investigate the multiphase interactions and self-assembled structure of nanoparticles at a trichloroethylene-water interface. The dodecanethiol-capped silver nanoparticles of 1-5 nm form randomly distributed multilayers at the liquid/liquid interface, with an interparticle distance varying from close contact to approximately 25 nm. This report offers the first direct observation of nanoparticles in a liquid medium using the environmental transmission electron microscope, as well as the first work revealing the detailed self-assembled structure of nanoparticles at a liquid/liquid interface when the size of the nanoparticles is comparable to the molecular dimension of the liquids.     

A New Method for the Characterization of Electrically Conducting Liquid Bridges

An electrical conductance technique is employed in investigating the behavior of constant volume liquid bridges when their length is altered. The liquid bridges are edge-pinned between two vertical, identical rods with a variable separation distance. Rods of different radius, material, and edge geometry are examined as they play a role in the response of the system. It is shown that liquid bridge volume and rod radius are the parameters that mainly influence the conductance signal. A mathematical framework is developed for the identification of the geometrical characteristics of liquid bridges explicitly from conductance data. The role of gravity is discussed in both the experiments and the theoretical analysis. The theoretical predictions obtained show a close agreement with measurements. Copyright 2000 Academic Press.     

Water dimer in liquid water

Summary A Self-Consistent Reaction Field Model is used to study the effect of the molecular environment on the electronic distribution and on the equilibrium geometry of the water dimer in liquid water. Computations are performed at the 6-311G++(2d,2p) MP2 level. Comparison of the results for the monomer and the dimer, in a vacuum and in the liquid, is made in order to gain a deeper insight on the cooperative phenomenon. The discussion emphasizes the trends which should be considered for deriving more sophisticated water-water potentials.     

Ruthenium nanoparticles in ionic liquids: structural and stability effects of polar solutes

Ionic liquids are a stabilizing medium for the in situ synthesis of ruthenium nanoparticles. Herein we show that the addition of molecular polar solutes to the ionic liquid, even in low concentrations, eliminates the role of the ionic liquid 3D structure in controlling the size of ruthenium nanoparticles, and can induce their aggregation. We have performed the synthesis of ruthenium nanoparticles by decomposition of [Ru(COD)(COT)] in 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C(1)C(4)Im][NTf(2)], under H(2) in the presence of varying amounts of water or 1-octylamine. For water added during the synthesis of metallic nanoparticles, a decrease of the solubility in the ionic liquid was observed, showed by nanoparticles located at the interface between aqueous and ionic phases. When 1-octylamine is present during the synthesis, stable nanoparticles of a constant size are obtained. When 1-octylamine is added after the synthesis, aggregation of the ruthenium nanoparticles is observed. In order to explain these phenomena, we have explored the molecular interactions between the different species using (13)C-NMR and DOSY (Diffusional Order Spectroscopy) experiments, mixing calorimetry, surface tension measurements and molecular simulations. We conclude that the behaviour of the ruthenium nanoparticles in [C(1)C(4)Im][NTf(2)] in the presence of 1-octylamine depends on the interaction between the ligand and the nanoparticles in terms of the energetics but also of the structural arrangement of the amine at the nanoparticle's surface.     

Nanoparticle‐based capillary electroseparation of proteins in polymer capillaries under physiological conditions

Totally porous lipid‐based liquid crystalline nanoparticles were used as pseudostationary phase for capillary electroseparation with LIF detection of proteins at physiological conditions using unmodified cyclic olefin copolymer capillaries (Topas^®, 6.7 cm effective length). In the absence of nanoparticles, i.e. in CE mode, the protein samples adsorbed completely to the capillary walls and could not be recovered. In contrast, nanoparticle‐based capillary electroseparation resolved green fluorescent protein from several of its impurities within 1 min. Furthermore, a mixture of native green fluorescent protein and two of its single‐amino‐acid‐substituted variants was separated within 2.5 min with efficiencies of 400 000 plates/m. The nanoparticles prevent adsorption by introducing a large interacting surface and by obstructing the attachment of the protein to the capillary wall. A one‐step procedure based on self‐assembly of lipids was used to prepare the nanoparticles, which benefit from their biocompatibility and suspension stability at high concentrations. An aqueous tricine buffer at pH 7.5 containing lipid‐based nanoparticles (2% w/w) was used as electrolyte, enabling separation at protein friendly conditions. The developed capillary‐based method facilitates future electrochromatography of proteins on polymer‐based microchips under physiological conditions and enables the initial optimization of separation conditions in parallel to the chip development.     

微乳液中单分散银纳米颗粒的制备及抗磨性能

采用水/液体石蜡/Span 80-Tween 80/正丁醇微乳液体系, 制备了具有良好单分散性的Ag纳米颗粒. 通过X射线粉末衍射仪、透射电子显微镜、傅立叶变换红外光谱仪和热分析仪表征了Ag纳米颗粒的结构、形貌、粒径大小及分布、表面键合性质和热性能. 结果表明, 所制备的Ag纳米颗粒具有立方晶型结构, m(Span 80)∶m(Tween 80)=7∶3时, 粒径分布呈单分散性, 平均粒径约为6 nm. 在四球长时抗磨损试验机上考察了分散于液体石蜡中Ag纳米颗粒的抗磨性能. 实验结果表明, Ag纳米颗粒具有良好的抗磨性, 且能显著提高基础油的承载能力.     

Effect of Asymmetric Anchoring Groups on Electronic Transport in Hybrid Metal/Molecule/Graphene Single Molecule Junctions

A combined experimental and theoretical study on molecular junctions with asymmetry in both the electrode type and in the anchoring group type is presented. A scanning tunnelling microscope is used to create the “asymmetric” Au-S-(CH₂)n-COOH-graphene molecular junctions and determine their conductance. The measurements are combined with electron transport calculations based on density functional theory (DFT) to analyze the electrical conductance and its length attenuation factor from a series of junctions of different molecular length (n). These results show an unexpected trend with a rather high conductance and a smaller attenuation factor for the Au-S-(CH₂)_n-COOH-graphene configuration compared to the equivalent junction with the “symmetrical” COOH contacting using the HOOC-(CH₂)_n-COOH series. Owing to the effect of the graphene electrode, the attenuation factor is also smaller than the one obtained for Au/Au electrodes. These results are interpreted through the relative molecule/electrode couplings and molecular level alignments as determined with DFT calculations. In an asymmetric junction, the electrical current flows through the less resistive conductance channel, similarly to what is observed in the macroscopic regime.