Electrically controlled waveguide mode in LC layer for fiber optic applications

A new electrically controlled waveguide mode for optical beams propagating in the plane of a liquid crystal (LC) layer is described. The mode is based on the total internal reflection of light beams from two parallel boundaries, which separates the regions of a liquid crystal cell with different director orientations and refractive indices. In experiments electric field was applied to the initially planar layer to produce the channel with a homeotropic orientation surrounded by the planar regions. It results in focusing and waveguide propagation of a light beam emitted by an optical fiber inserted in a liquid crystal cell. Scattering of light by thermal LC director fluctuations is used to visualize light beams propagation. The obtained waveguide mode can be used for an elaboration of electrically controlled LC switches with low operating voltages. The prototype of such device made with usage of a photolithography and a photo alignment technique is described. The possible ways of optimization of LC-switch are considered.     

Modeling light propagation in liquid crystal devices with a 3-D full-vector finite-element beam propagation method

A full-vector finite-element beam propagation method in 3-D is introduced for the simulation of light propagation in liquid crystal (LC) devices. The three electric field components are expressed in terms of mixed finite elements, providing the correct enforcement of boundary conditions. Moreover, the optical dielectric tensor of the medium can have all its nine elements nonzero, thus allowing the LC director to have an arbitrary orientation. A photonic crystal fiber with a LC infiltrated core and a homeotropic to multi-domain cell are analyzed. Comparison with other existing simulation techniques is provided, in order to validate the accuracy of the proposed method.     

一种液晶透镜盒间隙的测试方法

针对当前液晶透镜盒间隙测试存在的难题, 文中提出采用线偏振干涉法测试方法, 采用光强均匀分布的单色光入射, 检偏器的偏光轴方向与起偏器的偏光轴垂直或者平行, 液晶透镜的液晶取向层的摩擦方向与起偏器偏振轴夹角为45°, 此时干涉条纹亮暗差别最明显. 利用液晶透镜中心保持预倾角不变的透过率以及其他位置透过率最大值来计算液晶透镜的盒间隙, 该方法简单、可靠, 因采用光学手段测试, 其精确度相对较高. 关键词： 液晶透镜 盒间隙 线偏振光干涉 透过率     

基于液晶/聚合物光栅的高转化效率有机半导体激光器

采用有机半导体发光材料聚[2-甲氧基-5-(2-乙基己氧基)-1,4-苯乙炔]作为增益介质,低官能度光敏单体制备的液晶/聚合物光栅作为外部反馈谐振腔,制备出参数可独立控制的分离式结构的有机半导体激光器.液晶/聚合物光栅中液晶分子的取向影响光栅折射率调制量,从而影响光栅的反馈能力,最终影响激光器出射激光的性能.通过研究发现决定液晶分子取向的主要有两种与光栅周期有关的作用力,利用这一原理制备不同周期的光栅,光栅周期小于450 nm时,相分离出的液晶分子取向由光栅矢量方向变为光栅沟槽方向,此时光栅的折射率调制量增加,光反馈能力增强.采用周期为395 nm的液晶/聚合物光栅制备二级布拉格散射的有机半导体激光器,相较于大周期光栅(593 nm)制备的激光器,激光阈值由0.70μJ/pulse降低至0.18μJ/pulse,转化效率由2.5%提高到6.4%,且出射激光垂直于基板表面发射,有利于后续的处理及应用.     

Spin Hall effect of light in one-dimensional photonic crystal

We established a general propagating model to investigate the spin Hall effect of light in one-dimensional photonic crystal. A polarized (spin dependent) Gaussian beam which was incident obliquely through one-dimensional photonic crystal was demonstrated. Having decomposed a polarized Gaussian beam into different plane wave components charactering individual wave vectors, we revealed the transmission coefficient and reflection coefficient of each plane wave which propagates through the one-dimensional photonic crystal. It enabled us to obtain exact solution to the electric field of transmitted and reflected beams, and the analytical formula of light intensity, accordingly. A method based upon the partial differentials with the intensity distribution of the transmitted and reflected Gaussian beams was presented to determine the transverse and longitude shifts explicitly. Spin dependent shifts in one-dimensional photonic crystal provide alternative evidence for the spin Hall effect of light.     

Electrically switchable finite energy Airy beams generated by a liquid crystal cell with patterned electrode

A pair of electrically switchable finite energy Airy beams is generated by a liquid crystal (LC) cell, where one electrode is patterned by a photomask with a binary-phase pattern. Applying voltage across the LC cell, an index modulation is produced due to the liquid crystal molecules realignment, and the finite energy Airy beams can be generated or erased corresponding to the phase difference between the regions with and without electrode. The diffraction-free and transverse acceleration dynamics of this binary-phase element based finite energy Airy beams were experimentally verified, exhibiting excellent agreement with the theory.     

Light propagation in periodic photonic structures formed by photo-orientation and photo-polymerization of nematic liquid crystals

Propagation of linearly polarized light beams in a nematic liquid crystal cell with distinguished regions of different molecular orientation has been analyzed. Specifically, combination of the planar/homogenic and homeotropic alignment, forming thus spatially limited regions characterized by a different LC molecular orientation, has been tested, as achieved by means of the photo-orientation and photo-polymerization processes, independently. An influence of molecular orientation on the light beam propagation has been checked for different directions of the linear polarization. Thanks to the molecular reorientation induced by the low frequency external electric field and also to the reorientational nonlinearity taking place in NLCs, propagation direction of the light beam can be additionally controlled by the electric bias and/or optical power, respectively. Proposed structural solutions and techniques, related to the photo-orientation and photo-polymerization processes described in this communication, give rise to the novel LC geometries and structures. The latter act as promising candidates for new practical photonic applications as they are expected to be of a particular importance for integrated optic elements and devices.     

New regions of diffraction reflection in apodized one-dimensional photonic crystals with a large modulation depth

The specific features of light transmission in a cholesteric liquid crystal (LC) cell with a director rotated by 90° have been investigated. In this structure, where a light wave is incident at a large angle with respect to the LC surface, the light is reflected (refracted) in the LC layer near the opposite boundary. It is shown that the application of an electric field changes the character of extraordinary wave refraction, as a result of which light starts passing through a cell. The transmission threshold voltage is determined, and its dependence on the angle of incidence of light is obtained. The dependence of the transmitted-light intensity on the voltage across the cell is obtained as well. The same dependences are also derived by numerical calculations with allowance for the turning points and extinction.     

Electro- and magneto-optical switching of defect modes in one- dimensional photonic crystals

The transmission spectra of polarized light waves in a photonic crystal/liquid crystal (PC/LC) cell placed between crossed polarizers and controlled by an electric or magnetic field have been studied experimentally and theoretically. Electro- and magneto-optical switching based on the interference of polarized defect modes has been demonstrated. The transmission spectra of the PC/LC cell have been calculated as a function of the voltage applied to the LC layer and the magnetic field strength. The results of the calculations agree well with the experimental data.     

Liquid crystal orientation transition on microtextured substrates

A uniform alignment of liquid crystal (LC) with finite pretilt was observed on microtextured substrates that were lithographically fabricated with alternating horizontal and vertical corrugations. As the period of alternation was decreased toward 0.8 microm, the nematic LC alignment on these substrates changed from inhomogeneous in plane, copying the substrate corrugations, to a uniform configuration with a large pretilt of approximately 40 degrees. This transition is pertinent to a frustrated boundary wherein a lowering in the LC elastic energy due to spatial variation in the LC orientation compromises an increase in the surface anchoring energy. A model based on this idea demonstrates good agreement with the experiment. This result may open up a new arena for tailoring substrate characteristics for LC alignment.     

Three-phase contact line energetics from nanoscale liquid surface topographies

We observed light-induced alignment of the nematic liquid crystal, 4, 4(')-n-pentylcyanobiphenyl (5CB), on a fused quartz. Irradiation of the adsorbed layer with polarized ultraviolet light produced homogeneous alignment in a 5CB-filled liquid crystal cell with the easy orientation axis perpendicular to the polarization direction. The measured anchoring energy increases with illumination up to 10(-4) erg/cm (2). Phase retardation and pretilt measurements confirmed near homogeneous alignment of the LC in a cell, while the polarization dependence of second harmonic generation suggested a near normal alignment of the adsorbed layer. We believe that light-induced rearrangement or phototransformation of the adsorbed layer causes the observed phenomenon.     

NLC-CLC-NLC cell as an electrically tunable polarization plane rotator

A liquid crystal optical device made of an optically anisotropic heterostructure is considered. The device consists of a cholesteric liquid crystal (CLC) layer sandwiched by two phase-shifting anisotropic layers of a nematic liquid crystal (NLC). In this structure each of the NLC layers is a quarterwave plate. The problem is solved both by Ambartsumian’s method of layer addition and Muller’s matrix method. The peculiarities of reflection spectra, eigen polarizations, rotation of polarization plane and polarization ellipticity are studied. It is shown that this device can work as a light modulator or a system for obtaining linearly polarized light with electrically tunable rotation of the polarization plane (which is especially important for optical communication), as well as a device for obtaining the linearly polarized light from a non-polarized one.     

一维超声光子晶体禁带结构分析

超声波在介质中传播时可以引起介质的折射率发生周期变化,当光波垂直于超声波的传播方向时,这种介质可以被用来作为光栅使用,称为超声光栅。当光波沿超声波的传播方向通过这种介质时,它还可以用作一维光子晶体,并称其为一维超声光子晶体(1D-USPC)。利用平面波法证明了一维超声光子晶体具有一般一维周期层叠结构光子晶体的禁带特征。同时这种光子禁带是可以通过超声波的波长和振幅来改变的,这就为控制光的行为方面提供另一种新的方法。     

Field-induced transition from homeotropic to planar geometry in the SmC* phase of an electroclinic liquid crystal

The optical and electrical behavior was investigated of a symmetric liquid crystal (LC) cell: ITO–silane–LC–silane–ITO. The silane layer induces a perfect homeotropic alignment of the molecules of the studied electroclinic liquid crystal (ELC) material, BDH 764E. A field-induced transition from the perfect homeotropic to planar orientation in the chiral smectic C (SmC*) and smectic A (SmA) phases of the ELC was observed. Optical and dielectric studies were performed for both alignment (geometry) modes. The field-induced transition from the homeotropic to planar orientation was studied vis-à-vis the high negative dielectric anisotropy obtained in the studied material. Such an ELC with large negative dielectric anisotropy and perfect homeotropic alignment may have important implications for modern LC display technology.     

液晶电控双折射率与电压关系的研究

对向列相液晶BL-009作了电控双折射特性的研究。实验上采用简单、精确的偏光干涉法，利用岛津UV-3101PC型分光光度计，在入射光波长为630nm时，测出了液晶的透射率随交流电压的有效值和频率的变化曲线，从而得到液晶电控双折射率随电压的有效值和频率变化曲线。分析实验数据，可知液晶的电控双折射率随电压有效值的升高成一阶指数下降，而且，随电压频率的升高，在一定的范围内基本成线性下降。此实验结果对液晶器件的设计、制作、使用都具有一定的参考价值。     

快速测量扭曲向列相液晶盒盒厚

提出了一种利用圆偏光仪测量扭曲向列相液晶盒盒厚的新方法,即:圆偏光仪组成为两端是一对起偏器和检偏器,中间放置一对四分之一波片.起偏器和检偏器平行或垂直放置,其中一个四分之一波片的快轴和起偏器透光轴成45°,另一个四分之一波片的快轴和起偏器透光轴成－45°.液晶盒样品直接插入到两四分之一波片中间,无需调整方向.不同于旋转液晶盒或偏振片寻找输出光强最大值或最小值的方法,圆偏光仪测量盒厚不需要旋转任何光学元件或液晶盒观测输出光强的变化,只需要观测检偏器在平行和垂直方向的两个强度值,能够实现快速测量,简洁而且有效.     

Light-controlled helical pitch and dynamic gratings

A chiral nematic liquid crystal (LC) with a photo-sensitive chiral agent is employed for a light-controlled modulation of optical activity and used as a model substance for a dynamic diffraction grating recording. The described liquid crystalline system has shown a strong nonlinear response with effective parameter of cubic nonlinearity being much greater of that characteristic of the orientational nonlinearity of LC. A simple mathematical model of light diffraction on the grating of modulated optical activity was developed. Calculated values of intensities and polarisation states of diffracting beams have shown very good agreement with the experimental data. LC systems with light-controlled chirality could be promising media for nonlinear optical applications or all-optical switching devices.     

One-dimensional photonic crystals with a planar oriented nematic layer: Temperature and angular dependence of the spectra of defect modes

Transmission spectra of a one-dimensional photonic crystal (PC) formed by two multilayer dielectric mirrors and a planar oriented layer of 5CB nematic liquid crystal (LC) that is sandwiched between these mirrors and serves as a structure defect are investigated experimentally. Specific features of the behavior of the spectrum of defect modes as a function of the angle of incidence of light on the crystal are studied for two polarizations: parallel and perpendicular to the director of the LC; the director either lies in the plane of incidence or is perpendicular to it. It is shown that, for the configurations considered, the maxima of the defect modes shift toward the short-wavelength region as the tilt angle of incidence radiation increases; this tendency is more manifest for the parallel-polarized component, when the director lies in the plane of incidence. In the latter case, the width of the photonic band gap (PBG) appreciably decreases. The temperature dependence of the polarization components of the transmission spectra of a PC is investigated in the case of normal incidence of light. The spectral shift of defect modes due to the variation of the refractive index of the LC at the nematic-isotropic liquid phase transition point is measured. It is shown that, in real PCs, the amplitude of defect modes decreases when approaching the center of the band gap, as well as when the number of layers in the dielectric mirrors increases. Theoretical transmission spectra of the PCs calculated by the method of recurrence relations with regard to the decay of defect modes are in good agreement with experimental data.     

Comparison of optical compensations based on discotic liquid crystals with linear and non-linear orientation for wide viewing angle twisted nematic liquid crystal displays

Optical compensation film using discotic liquid crystals has been commercialized to suppress light leakage of twisted nematic (TN) liquid crystal (LC) cells in the dark state when the viewing directions are off-axes. In the conventional film, the tilt angle variation of the discotic LC layers is linear, whereas that of the rod-like LC layers in the TN cell is non-linear with twist alignment. We investigated the optical compensation effects in terms of iso-contrast ratio, gray scale inversion and color shift with linear and non-linear orientation in a tilt angle or twist and non-twist orientation on TN-LC cells. The results showed that the optical compensation with non-linear orientation exhibited an improved performance in suppressing light leakage in the dark state.     

SIMULATING STUDY ON INTERNAL SELF-PUMPED PHASE CONJUGATORS WITH EXTERNAL CONFIGURATIONS

A new method is proposed to study the properties of stimulated photorefractive backscat-tering and four-wave-mixing (SPB-FWM) and total-internal-reflection (TIR) self-pumped phase conjugators. The phase conjugators are simulated with external configurations using a KNSBN:Cu crystal, a plane mirror and a prism. As a result, the parameters such as beamwidth and intensity of the contra-directionally propagating pump beams for the FWM interactions in the crystal can be easily controlled. The dependence of self-pumped phase conjugation reflectivity and FWM coupling strength on these parameters of the pump beams have been studied.