Comparison of CO2 Reduction Performance with NH3 and H2O between Cu/TiO2 and Pd/TiO2

The aim of this study is to clarify the effect of doped metal type on CO₂ reduction characteristics of TiO₂ with NH₃ and H₂O. Cu and Pd have been selected as dopants for TiO₂. In addition, the impact of molar ratio of CO₂ to reductants NH₃ and H₂O has been investigated. A TiO₂ photocatalyst was prepared by a sol-gel and dip-coating process, and then doped with Cu or Pd fine particles by using the pulse arc plasma gun method. The prepared Cu/TiO₂ film and Pd/TiO₂ film were characterized by SEM, EPMA, TEM, STEM, EDX, EDS and EELS. This study also has investigated the performance of CO₂ reduction under the illumination condition of Xe lamp with or without ultraviolet (UV) light. As a result, it is revealed that the CO₂ reduction performance with Cu/TiO₂ under the illumination condition of Xe lamp with UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:1:1 while that without UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:0.5:0.5. It is revealed that the CO₂ reduction performance of Pd/TiO₂ is the highest for the molar ratio of CO₂/NH₃/H₂O = 1:1:1 no matter the used Xe lamp was with or without UV light. The molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp with UV light was 10.2 μmol/g, while that for Pd/TiO₂ was 5.5 μmol/g. Meanwhile, the molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp without UV light was 2.5 μmol/g, while that for Pd/TiO₂ was 3.5 μmol/g. This study has concluded that Cu/TiO₂ is superior to Pd/TiO₂ from the viewpoint of the molar quantity of CO per unit weight of photocatalyst as well as the quantum efficiency.     

TiO2–carbon nanotube heterojunction arrays with a controllable thickness of TiO2 layer and their first application in photocatalysis

TiO₂–carbon nanotube (CNT) heterojunction arrays on Ti substrate were fabricated by a two-step thermal chemical vapor deposition (CVD) method. CNT arrays were first grown on Ti substrate vertically, and then a TiO₂ layer, whose thickness could be controlled by varying the deposition time, was deposited on CNTs. Measured by electrochemical impedance spectroscopy (EIS), the thickness of the TiO₂ layer could affect the photoresponse ability significantly. About 100 nm thickness of the TiO₂ layer proved to be best for efficient charge separation among the tested samples. The optimized TiO₂–CNT heterojunction arrays displayed apparently higher photoresponse capability than that of TiO₂ nanotube arrays which was confirmed by surface photovoltage (SPV) technique based on Kelvin probe and EIS. In the photocatalytic experiments, the kinetic constants of phenol degradation with TiO₂–CNT heterojunctions and TiO₂ nanotubes were 0.75 h⁻¹ (R² = 0.983) and 0.39 h⁻¹ (R² = 0.995), respectively. At the same time, 53.7% of total organic carbon (TOC) was removed with TiO₂–CNT heterojunctions, while the removal of TOC was only 16.7% with TiO₂ nanotubes. These results demonstrate the super capability of the TiO₂–CNT heterojunction arrays in photocatalysis with comparison to TiO₂-only nanomaterial.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Au Modified F-TiO2 for Efficient Photocatalytic Synthesis of Hydrogen Peroxide

In this work, Au-modified F-TiO₂ is developed as a simple and efficient photocatalyst for H₂O₂ production under ultraviolet light. The Au/F-TiO₂ photocatalyst avoids the necessity of adding fluoride into the reaction medium for enhancing H₂O₂ synthesis, as in a pure TiO₂ reaction system. The F⁻ modification inhibits the H₂O₂ decomposition through the formation of the ≡Ti–F complex. Au is an active cocatalyst for photocatalytic H₂O₂ production. We compared the activity of TiO₂ with F⁻ modification and without F⁻ modification in the presence of Au, and found that the H₂O₂ production rate over Au/F-TiO₂ reaches four times that of Au/TiO₂. In situ electron spin resonance studies have shown that H₂O₂ is produced by stepwise single-electron oxygen reduction on the Au/F-TiO₂ photocatalyst.     

CO2 Sorbents Based on Spherical Carbon and Photoactive Metal Oxides: Insight into Adsorption Capacity,Selectivity and Regenerability

This work aimed to obtain hybrid composites based on photoactive metal oxide and carbon having adsorption properties. The materials, composed of titanium dioxide or zinc oxide and spherical carbon, were obtained from resorcinol-formaldehyde resin, treated in a solvothermal reactor heated with microwaves and then subjected to carbonization, were received. The functional groups of pure carbon spheres (unsaturated stretching C=C, stretching C−OH and C−H bending vibrations), CS/ZnO and CS/TiO₂ samples were determined by FT-IR analysis. The characteristic bands for ZnO and TiO₂ were observed below 1000 cm⁻¹. The thermal oxidative properties are similar for TiO₂- and ZnO-modified carbon spheres. We have observed that the increased carbon sphere content in nanocomposites results in starting the decomposition process at a lower temperature, therefore, nanocomposites have a broader combustion temperature range. The effect of the oxides’ addition to carbon spheres on their adsorption properties was evaluated in detail by examining CO₂ adsorption from the gas phase. The selectivity of CO₂ over N₂ at a temperature of 25 °C and pressure of 1 bar (a novelty in testing CS-based sorbents) calculated for 3.00 CS/TiO₂ and 4.00 CS/ZnO was 15.09 and 16.95, respectively. These nanocomposites exhibit excellent cyclic stability checked over 10 consecutive adsorption–desorption cycles.     

Au-TiO2/Chit modified sensor for electrochemical detection of trace organophosphates insecticides

In this paper, Au–TiO₂/Chit modified electrode was prepared with Au–TiO₂ nanocomposite (Au–TiO₂) and Chitosan (Chit) as a conjunct. The Au–TiO₂ nanocomposite and the films were characterized by electrochemical and spectroscopy methods. A set of experimental conditions was also optimized for the film's fabrication. The electrochemical and electrocatalytic behaviors of Au–TiO₂/Chit modified electrode to trace organophosphates (OPs) insecticides such as parathion were discussed in this work. By differential pulse voltammetry (DPV) measurement, the current responses of Au–TiO₂/Chit modified electrode were linear with parathion concentration ranging from 1.0 ng/ml to 7.0 × 10³ ng/ml with the detection limit of 0.5 ng/ml. In order to evaluate the performance of the detection system, we also examined the real samples successfully in this work. It exhibited a sensitive, rapid and easy-to-use method for the fast determination of trace OPs insecticides.     

Synthesis of Mesoporous TiO2/SiO2 Hybrid Films as an Efficient Photocatalyst by Polymeric Micelle Assembly

Thermally stable mesoporous TiO₂/SiO₂ hybrid films with pore size of 50 nm have been synthesized by adopting the polymeric micelle‐assembly method. A triblock copolymer, poly(styrene‐b‐2‐vinyl pyridine‐b‐ethylene oxide), which serves as a template for the mesopores, was utilized to form polymeric micelles. The effective interaction of titanium tetraisopropoxide (TTIP) and tetraethyl orthosilicate (TEOS) with the polymeric micelles enabled us to fabricate stable mesoporous films. By changing the molar ratio of TEOS and TTIP, several mesoporous TiO₂/SiO₂ hybrid films with different compositions can be synthesized. The presence of amorphous SiO₂ phase effectively retards the growth of anatase TiO₂ crystal in the pore walls and retains the original mesoporous structure, even at higher temperature (650 °C). These TiO₂/SiO₂ hybrid films are of very high quality, without any cracks or voids. The addition of SiO₂ phase to mesoporous TiO₂ films not only adsorbs more organic dyes, but also significantly enhances the photocatalytic activity compared to mesoporous pure TiO₂ film without SiO₂ phase.     

Photocatalytic hydrogen evolution over mesoporous TiO2/metal nanocomposites

Na⁺ complex with the dibenzo-18-crown-6 ester was used as a template to synthesize mesoporous titanium dioxide with the specific surface area 130–140 m²/g, pore diameter 5–9 nm and anatase content 70–90%. The mesoporous TiO₂ samples prepared were found to have photocatalytic activity in Cu^II, Ni^II and Ag^I reduction by aliphatic alcohols. The resulting metal–semiconductor nanostructures have remarkable photocatalytic activity in hydrogen evolution from water–alcohol mixtures, their efficiency being 50–60% greater than that of the metal-containing nano-composites based on TiO₂ Degussa P25.The effects of the thermal treatment of mesoporous TiO₂ upon its photocatalytic activity in hydrogen production were studied. The anatase content and pore size were found to be the basic parameters determining the photoreaction rate. The growth of the quantum yield of hydrogen evolution from TiO₂/Ag⁰ to TiO₂/Ni⁰ to TiO₂/Cu⁰ was interpreted in terms of differences in the electronic interaction between metal nanoparticles and the semiconductor surface. It was found that there is an optimal metal concentration range where the quantum yield of hydrogen production is maximal. A decrease in the photoreaction rate at further increment in the metal content was supposed to be connected with the enlargement of metal nanoparticles and deterioration of the intimate electron interaction between the components of the metal–semiconductor nanocomposites.     

Formation of appropriate sites on nanofiltration membrane surface for binding TiO2 photo-catalyst: Performance, characterization and fouling-resistant capability

Titanium dioxide (TiO₂) nanoparticles were assembled on the surface of nanofiltration blend membrane. For settling TiO₂ on the membrane surface, two membrane categories were used: (i) unmodified polyethersulfone (PES)/polyimide (PI) blend membrane, and (ii) –OH functionalized PES/PI blend membrane with different concentrations of diethanolamine (DEA). These membranes were radiated by UV light after TiO₂ depositing with different concentrations. 15 min immersion in colloidal suspension and 15 min UV irradiation with 160 W lamps were used for modification. The modification resulted in the formation of a photo-catalytic property with enhanced membrane hydrophilicity. The self-assembly of TiO₂ nanoparticles was established through coordinance bonds with –OH functional groups on the membrane surface. A comparison between the UV irradiated TiO₂ deposited blend membrane and deposited-functionalized blend membranes showed that –OH groups originate excellent adhesion of TiO₂ nanoparticles on the membrane surface, increase reversible deposition, and diminish irreversible fouling. The membranes were characterized using SEM, FTIR, EDX, contact angle, cross flow filtration, and antifouling measurements. SEM images show that the presence of –OH groups on the DEA-modified membrane surface is the main parameter for extra uniformly settlement of TiO₂ nanoparticles on the membrane surface. This procedure is a superior technique for modification of PES/PI nanofiltration membranes to enhance water flux and minimization membrane fouling.     

Topotaxial formation of titanium-rich barium titanates during solid state reactions on (110) TiO2 (rutile) and (001) BaTiO3 single crystals

The orientation relationships of Ti-rich barium titanate phases formed by solid state reactions at high temperatures were studied using (110) TiO₂ (rutile) and (001) BaTiO₃ single-crystal substrates. Well-oriented Ba₆Ti₁₇O₄₀ islands were observed after a vapor–solid reaction of a BaO quantity equivalent to a nominal BaO film thickness of 1 nm with the TiO₂ substrate, whereas a thin film consisting of well-oriented BaTiO₃ and Ba₆Ti₁₇O₄₀ grains was formed after vapor–solid reaction of a BaO quantity equivalent to a nominal BaO film thickness of 50 nm with the rutile substrate. A topotaxial orientation relationship between Ba₆Ti₁₇O₄₀ and TiO₂ was found. Topotaxy is facilitated by a certain similarity in the oxygen sublattices of TiO₂ and Ba₆Ti₁₇O₄₀. The mechanism of the reaction occurring between BaO vapor and the TiO₂ surface at high temperature is discussed. On the other hand, several well-oriented Ba₄Ti₁₃O₃₀, Ba₆Ti₁₇O₄₀ and Ba₂Ti₅O₁₂ phases were observed to be embedded in the mainly forming Ba₂TiSi₂O₈ phase after a solid–solid reaction of amorphous SiO₂ thin films with (001) BaTiO₃ substrates at temperatures above 1000 °C. They were formed by a topotaxial reaction involving the transformation of (111) planes of BaTiO₃ into (001) planes of the Ti-rich phases by removal of BaO and insertion of TiO₂. Cross-sections of the interfaces between the substrates and the various reaction products are studied by (high-resolution) transmission electron microscopy.     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Hydrothermal synthesis of mesostructured nanocrystalline TiO2 in an ionic liquid–water mixture and its photocatalytic performance

Anatase mesostructured TiO₂ nanocrystalline was prepared in a mixture of 1-butyl-3-methyl-imidazolium tetrafluoroborate (BMIM⁺BF₄⁻) ionic liquid and water by a low temperature hydrothermal method. The obtained materials were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and N₂ adsorption–desorption. The existence of BMIM⁺BF₄⁻ enhanced the polycondensation and crystallization rate, which encouraged the formation of anatase crystal. The TiO₂ particles were thermally very stable and thus resistant to anatase-rutile phase transformation during calcination at high temperatures. The anatase TiO₂ showed high photocatalytic activity in the degradation of p-chlorophenol than that of the commercially available TiO₂, Degussa P25. After 2 h reaction under the UV-irradiation of 250 W, the removing rate of p-chlorophenol was up to 96.3%.     

Pulsed laser-induced oxygen deficiency at TiO2 surface: Anomalous structure and electrical transport properties

We have studied pulsed laser-induced oxygen deficiencies at rutile TiO₂ surfaces. The crystal surface was successfully reduced by excimer laser irradiation, and an oxygen-deficient TiO_2−δ layer with 160 nm thickness was formed by means of ArF laser irradiation at 140 mJ/cm² for 2000 pulses. The TiO_2−δ layer fundamentally maintained a rutile structure, though this structure was distorted by many stacking faults caused by the large oxygen deficiency. The electrical resistivity of the obtained TiO_2−δ layer exhibited unconventional metallic behavior with hysteresis. A metal–insulator transition occurred at 42 K, and the electrical resistivity exceeded 10⁴ Ω cm below 42 K. This metal–insulator transition could be caused by bipolaronic ordering derived from Ti–Ti pairings that formed along the stacking faults. The constant magnetization behavior observed below 42 K is consistent with the bipolaronic scenario that has been observed previously for Ti₄O₇. These peculiar electrical properties are strongly linked to the oxygen-deficient crystal structure, which contains many stacking faults formed by instantaneous heating during excimer laser irradiation.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

Promoting effect of Mg in supported Mo/HBeta–Al2O3 catalyst for cross-metathesis of ethene and butene-2 to propene

Promoting effects of Mg in heterogeneous Mo/HBeta–Al₂O₃ catalyst have been carefully studied for cross-metathesis of ethene and butene-2 to propene. The catalyst shows good stability with Mg content in the range of 1–2 wt%. Such effect may be attributed to the elimination of weak acid sites through introduction of Mg which suppresses the side olefin oligomerization reaction, as evidenced from NH₃-TPD and ¹H MAS NMR results. Addition of more Mg content to 3 wt% may change the state and reducibility of Mo species, as indicated from the UV–vis, UV-Raman and H₂-TPR measurements. The increasing difficulty for the reduction of Mo(VI) species is closely related with the poor performance of 3 wt% Mg–4Mo/HBeta–30% Al₂O₃ catalyst in the metathesis reaction.     

Surface structure for Au on (0 0 1) SrTiO3

First-principle calculations are performed to study the crystal structure, formation energies, and electronic structures of (0 0 1) SrTiO₃ surfaces with/without Au covered. The initiative Au additive layer is crystallized in a fcc structure with (0 0 1) face on SrO-terminated surface. The bimodal growth trend of Au on TiO₂-terminated surface is qualitatively consistent with the experimental observations. The defect structure of Au occupying the oxygen (O) vacancies of TiO₂-terminated surface is energetically favorable under oxygen-poor conditions, and a feature corresponding to gap states appear and the occupied Ti 3d states disappear.     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

可移动金核的二氧化钛空心球合成及光催化性质

Uniform hollow Au@TiO₂ core shell spheres with moveable Au nanoparticles were synthesized based on templating against Au@carbon spheres. The diameter of the shell of the Au@TiO₂ spheres could be controlled by adjusting the Ti(OC₄H₉)₄ hydrolyzing reaction time or the ratio of Ti(OC₄H₉)₄ to Au@carbon spheres, and the shell thickness of the core-shell spheres can be varied from 25 nm to 40 nm. As prepared hollow Au@TiO₂ core-shell spheres display enhanced photocatalytic activity in the initial stage of photocatalytic degradation of methylene blue compared with pure hollow TiO₂ spheres and the commercial photocatalyst TiO₂(P-25).     

Molecularly Imprinted Methyl-Modified Hollow TiO2 Microspheres

The possibility of generating organically modified hollow TiO₂ microspheres via a simple sol-gel synthesis was demonstrated for the first time in this work. A mixture of titania precursors, including an organically modified precursor, was used to obtain methyl-modified hollow TiO₂ microspheres selective for bilirubin by the molecular imprinting technique (Methyl-HTM-MIM). Methyl-HTM-MIM were prepared by a sol-gel method using titanium (IV) isopropoxide (TTIP), and methyltitanium triisopropoxide (MTTIP) as precursors. Two ratios of titania precursors were tested (1/6 and 1/30 mol_MTTIP/mol_TTIP). With the characterization results obtained by the SEM and ATR-FTIR techniques, it was possible to establish that only the 1/30 mol_MTTIP/mol_TTIP ratio allowed for the preparation of hollow spheres with a reasonably homogeneous methylated-TiO₂ shell. It was possible to obtain a certain degree of organization of the hybrid network, which increased with calcination temperatures. By adjusting isothermal adsorption models, imprinting parameters were determined, indicating that the new methylated microspheres presented greater selectivity for bilirubin than the totally inorganic hollow TiO₂ microspheres. The effectiveness of the molecular imprinting technique was proven for the first time in an organically modified titania material, with imprinting factor values greater than 1.4, corresponding to a significant increase in the maximum adsorption capacity of the template represented by the molecularly imprinted microspheres. In summary, the results obtained with the new methyl-HTM-MIM open the possibility of exploring the application of these microspheres for selective sorption (separation or sensing, for example) or perhaps even for selective photocatalysis, particularly for the degradation of organic compounds.     

Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.