Ignition and volatile combustion behaviors of a single lignite particle in a fluidized bed under O2/H2O condition

O₂/H₂O combustion, as a new evolution of oxy-fuel combustion, has gradually gained more attention recently for carbon capture in a coal-fired power plant. The physical and chemical properties of steam e.g. reactivity, thermal capacity, diffusivity, can affect the coal combustion process. In this work, the ignition and volatile combustion characteristics of a single lignite particle were first investigated in a fluidized bed combustor under O₂/H₂O atmosphere. The flame and particle temperatures were measured by a calibrated two-color pyrometry and pre-buried thermocouple, respectively. Results indicated that the volatile flame became smaller and brighter as the oxygen concentration increased. The ignition delay time of particle in dense phase was shorter than that in dilute phase due to its higher heat transfer coefficient. Also, the volatile flame was completely separated from particles (defined as off-flame) in dense phase while the flame lay on the particle surface (defined as on-flame) in dilute phase. The self-heating of fuel particles by on-flame in dilute phase was more obvious than that in dense phase, leading to earlier char combustion. At low oxygen concentration, the flame in the H₂O atmosphere was darker than that in the N₂ atmosphere because the heat capacity of H₂O is higher than that of N₂. With the increase of oxygen concentration, the flame temperature in the O₂/H₂O atmosphere was dramatically enhanced rather than that in the O₂/N₂ atmosphere, where the diffusion rate of oxygen in O₂/N₂ atmosphere became the dominant factor.     

A three mixture fraction flamelet model for multi-stream laminar pulverized coal combustion

A three mixture fraction flamelet model is proposed for multi-stream laminar pulverized coal combustion. The technique of coordinate transformation is utilized to map the flamelet solutions from a unit pyramid space into a unit cubic space to improve the stability of the simulation. The validity of the three mixture fraction flamelet model was assessed on different configurations, including a laminar counterflow pulverized coal/methane flame and a laminar piloted pulverized coal jet flame. The flamelet predictions were compared to the reference results of the detailed chemistry solutions. For the counterflow flame, it was found that the flame temperature and major species mass fractions are correctly predicted by the three mixture fraction flamelet model. However, discrepancies are observed for combustion-mode-sensitive species such as CO and H₂ in the premixed combustion region. The thermo-chemical quantities in the char surface reaction zone cannot be correctly predicted if the mixing between the char off-gas stream and other streams is neglected. For the piloted jet flame, it was shown that the stable thermo-chemical variables can be correctly predicted at the upper and middle stream locations. However, at the downstream location, discrepancies can be observed in certain regions. Overall, the validity of the three mixture fraction flamelet model for multi-stream pulverized coal combustion is confirmed and its performance in turbulent pulverized coal combustion will be tested in future work.     

Effect of CO2 gasification reaction on oxy-combustion of pulverized coal char

For oxy-combustion with flue gas recirculation, as is commonly employed, it is recognized that elevated CO₂ levels affect radiant transport, the heat capacity of the gas, and other gas transport properties. A topic of widespread speculation has concerned the effect of the CO₂ gasification reaction with coal char on the char burning rate. To give clarity to the likely impact of this reaction on the oxy-fuel combustion of pulverized coal char, the Surface Kinetics in Porous Particles (SKIPPY) code was employed for a range of potential CO₂ reaction rates for a high-volatile bituminous coal char particle (130 μm diameter) reacting in several O₂ concentration environments. The effects of boundary layer chemistry are also examined in this analysis. Under oxygen-enriched conditions, boundary layer reactions (converting CO to CO₂, with concomitant heat release) are shown to increase the char particle temperature and burning rate, while decreasing the O₂ concentration at the particle surface. The CO₂ gasification reaction acts to reduce the char particle temperature (because of the reaction endothermicity) and thereby reduces the rate of char oxidation. Interestingly, the presence of the CO₂ gasification reaction increases the char conversion rate for combustion at low O₂ concentrations, but decreases char conversion for combustion at high O₂ concentrations. These calculations give new insight into the complexity of the effects from the CO₂ gasification reaction and should help improve the understanding of experimentally measured oxy-fuel char combustion and burnout trends in the literature.     

Effect of gasification reactions on biomass char conversion under pulverized fuel combustion conditions

The effect of gasification reactions on biomass char conversion under pulverized fuel combustion conditions was studied by single particle experiments and modelling. Experiments of pine and beech wood char conversion were carried out in a single particle combustor under conditions of 1473-1723 K, 0.0-10.5% O₂, and 25-42% H₂O. A comprehensive progressive char conversion model, including heterogeneous reactions (char oxidation and char gasification with CO₂ and H₂O), homogeneous reactions (CO oxidation, water-gas shift reaction, and H₂ oxidation) in the particle boundary layer, particle shrinkage, and external and internal heat and mass transfer, was developed. The modelling results are in good agreement with both experimental char conversion time and particle size evolution in the presence of oxygen, while larger deviations are found for the gasification experiments. The modelling results show that the char oxidation is limited by mass transfer, while the char gasification is controlled by both mass transfer and gasification kinetics at the investigated conditions. A sensitivity analysis shows that the CO oxidation in the boundary layer and the gasification kinetics influence significantly the char conversion time, while the water-gas shift reaction and H₂ oxidation have only a small effect. Analysis of the sensitive parameters on the char conversion process under a typical pulverized biomass combustion condition (4% O₂, 13% CO₂, 13% H₂O), shows that the char gasification reactions contribute significantly to char conversion, especially for millimeter-sized biomass char particles at high temperatures.     

Pulverized coal swirl flames in oxy-fuel conditions: Effects of oxidizer O2 concentration on flow field and local gas composition

In an experimental study the effects of varied oxygen concentrations in the oxidizer gas on resulting flow fields, combustion products and general behavior of pulverized coal swirl flames under oxy-fuel conditions have been investigated. Experiments were carried out in a small scale down-fired cylindrical combustion chamber equipped with an annular swirl burner. Studied flames had a constant power output of 40 kW_th and O₂/CO₂ oxidizer gas mixtures with O₂ concentrations ranging from 23 to 33 vol%. Detailed two-dimensional flow field measurements are obtained from laser Doppler anemometry (LDA). Velocity profiles (Mean and RMS) have been obtained for all conditions investigated and serve as basis for identification of flow field characteristics. Velocity RMS values are provided as supplementary material. To complement flow field measurements, in-flame gas composition measurements were also conducted using a sampling probe combined with infrared gas absorption analysis via Fourier-transform infrared (FTIR) spectrometry. The results obtained show increased velocities, particularly along the main vortex for flames with increased oxygen contents, while lower velocities are found to occur inside the recirculation regions. The opposite occurs with lower O₂ concentrations, showing significantly reduced velocities in the main vortex, but stronger recirculation than the high oxygen counterparts. This effect is attributed to a modification of the swirl level introduced by the expansion of product gases. Measured NO and CO in-flame concentrations showed significant variations under different O₂ concentrations in the oxidizer.     

Particle imaging of ignition and devolatilization of pulverized coal during oxy-fuel combustion

Oxy-fuel combustion of coal is a promising technology for cost-effective power production with carbon capture and sequestration that has ancillary benefits of emission reductions and lower flue gas cleanup costs. To fully understand the results of pilot-scale tests of oxy-fuel combustion and to accurately predict scale-up performance through CFD modeling, fundamental data are needed concerning coal and coal char combustion properties under these unconventional conditions. In the work reported here, the ignition and devolatilization characteristics of both a high-volatile bituminous coal and a Powder River Basin subbituminous coal were analyzed in detail through single-particle imaging at a gas temperature of 1700 K over a range of 12–36 vol % O₂ in both N₂ and CO₂ diluent gases. The bituminous coal images show large, hot soot cloud radiation whose size and shape vary with oxygen concentration and, to a lesser extent, with the use of N₂ versus CO₂ diluent gas. Subbituminous coal images show cooler, smaller emission signals during devolatilization that have the same characteristic size as the coal particles introduced into the flow (nominally 100 μm). The measurements also demonstrate that the use of CO₂ diluent retards the onset of ignition and increases the duration of devolatilization, once initiated. For a given diluent gas, a higher oxygen concentration yields shorter ignition delay and devolatilization times. The effect of CO₂ on coal particle ignition is explained by its higher molar specific heat and its tendency to reduce the local radical pool. The effect of O₂ on coal particle ignition results from its effect on the local mixture reactivity. CO₂ decreases the rate of devolatilization because of the lower mass diffusivity of volatiles in CO₂ mixtures, whereas higher O₂ concentrations increase the mass flux of oxygen to the volatiles flame and thereby increase the rate of devolatilization.     

A new technique for the measurement of the product CO/CO2 ratio at the surface of char particles burning in a fluidized bed

A new experimental technique is proposed to measure the product CO/CO₂ ratio at the surface of spherical char particles during fluidized bed combustion. It is based on the measurement of the burning rate of a single char particle under low oxygen concentration conditions and on the use of an accurate prediction of the particle Sherwood number. This technique was applied to spherical char particles obtained from a bituminous coal which is characterized by a low attrition and fragmentation propensity. The product CO/CO₂ ratio was measured at a bed temperature of 850 °C and at a fluidization velocity of 0.3 m/s in a lab-scale apparatus operated with a bed of 0.5–0.6 mm sand. The char particle size was varied between 2 and 7 mm and the inlet oxygen concentration between 0.1% and 2.0%. Results showed that under the experimental conditions investigated carbon was mostly oxidized to CO₂ within the particle boundary layer, with a maximum fraction of carbon escaping as CO of 10–20% at the lowest oxygen concentrations and largest particle sizes.     

A DNS study on temporally evolving jet flames of pulverized coal/biomass co-firing with different blending ratios

Biomass co-firing within the existing pulverized coal boiler is thought as a practical near-term way of biomass utilization, while its detailed combustion characteristics and pollutant formation have not yet been fully understood. In the present study, we report a Carrier-phase Direct Numerical Simulation study coupled with detailed mechanism to provide a deep insight into the coal/biomass co-firing (CBCF) jet flames under different blending ratios. It is found that compared with the pure coal flame, the CBCF could (i) prompt the volatiles ignition, produce higher H₂O and similar CO₂ mass fractions at blending ratios of 20% and 40%, and obviously reduce the gas temperature and CO₂ mass fraction at the blending ratio of 50%; (ii) prompt the coal devolatilization and char burnout at blending ratios of 20% and 40%, while the char burnout is reduced when blending ratio is 50% due to the local enrichment of large particles and lack of oxygen; (iii) reduce the thermal, prompt, NNH and N₂O-intermediate routes of NO formation, but show limited effect on the NO-reburning route of NO destruction, therefore, resulting in an obvious NO reduction.     

Flame characterisation of gas-assisted pulverised coal combustion using FPV-LES

A multiphase flamelet/progress variable (FPV) model for the large eddy simulation (LES) of gas-assisted pulverised coal combustion (PCC) is developed. The target of the simulation is the Darmstadt turbulent gas-assisted swirling solid fuel combustion chamber. The coal particles are treated as Lagrangian point particles, the position, momentum and energy of which are tracked. The gas phase is described by the low-Mach Navier-Stokes equations alongside the Eulerian transport equations of the governing variables for the FPV model. The set of chemical states of the PCC flame is pre-tabulated in a six-dimensional flamelet table and determined by the mixing of the primary fuel stream, volatiles and char off-gases with the oxidising air, the progress of chemical reactions, the interphase heat transfer, as well as sub-grid scale variations. A presumed $\beta$-PDF approach for the total mixture fraction is applied to capture sub-grid scale effects. The discrete ordinate method (DOM) with the weighted sum of grey gases model (WSGGM) is employed to model radiation. The FPV-LES results are validated against the experimental evidence and a good agreement of the predicted mean and RMS velocities, as well as the mean gas temperature between experiments and simulations is obtained. The contributions of the pilot, volatile and char off-gas fuel streams to the coal flame are analysed. It is found that most regions of the furnace are dominated by either pilot or volatile combustion, while char conversion only occurs in the far downstream and outer furnace regions. The pilot gas dominates the near-wall region inside the quarl, whereas the volatile gas mainly released from small particles dominates a first volatile combustion zone in the interior of the internal recirculation zone. Larger particles heat up more slowly and release their volatile content further downstream, leading to a secondary volatile combustion zone.     

A reduced mechanism for primary reactions of coal volatiles in a plug flow reactor

In the present paper, the authors study the primary reactions of coal volatiles and a detailed mechanism has been made for three different environments: thermal decomposition (pyrolysis), partial oxidation (O₂) and O₂/CO₂ gasification in a plug flow reactor to analyze the combustion component. The computed results have similar trend for three different environments with the experimental data. A systematically reduced mechanism for O₂/CO₂ gasification has also been derived by examination of Rate of Production (ROP) analysis from the detailed mechanism (255 species and 1095 reactions). The reduced mechanism shows similar result and has been validated by comparing the calculated concentrations of H₂, CH₄, H₂O, CO, CO₂ and polycyclic aromatic hydrocarbon (PAH) with those of the detailed mechanism in a wide range of operating conditions. The authors also predicted the concentration profiles of H₂, CO, CO₂ and PAH at high temperature and high pressure.     

Single particle ignition and combustion of pulverized pine wood,wheat straw,rice husk and grape pomace

This work examines the combustion behavior of single pulverized biomass particles from ignition to early stages of char oxidation. The biomass residues investigated were pine wood, wheat straw, rice husk and grape pomace. The biomass particles, in the size range 224–250 µm, were injected upward into a confined region with hot combustion products, produced by a flat flame McKenna burner, with a mean temperature of 1610 K and a mean O₂ concentration of 6.5 vol%. Temporally and spectrally resolved images of the single burning particles were recorded with an intensified charge-coupled device camera equipped with different band-pass spectral filters. Data are reported for CH*, C₂*, Na* and K* chemiluminescence, and thermal radiation from soot and char burning particles. The data on CH* and C₂* chemiluminescence and soot thermal radiation permits to identify important differences between the ignition delay time, volatiles combustion time and soot formation propensity of the four biomass residues, which are mainly affected by their volatile matter content. The Na* and K* emission signals follow the same trends of the CH* and C₂* emission signals until the end of the volatiles combustion stage, beyond which, unlike the CH* and C₂* emission signals, they persist owing to their release from the char burning particles. Moreover, during the volatiles combustion stage, the Na*/CH* and K*/CH* ratios present constant values for each biomass residue. The CH* and thermal radiation emission data suggest that all biomass char particles experienced heterogeneous oxidation at or immediately after the extinction of the homogeneous volatiles combustion.     

In situ parametric study of alkali release in pulverized coal combustion: Effects of operating conditions and gas composition

This work concerns a parametric study of alkali release in a lab-scale, pulverized coal combustor (drop tube reactor) at atmospheric pressure. Measurements were made at steady reactor conditions using excimer laser fragmentation fluorescence (ELIF) and with direct optical access to the flue gas pipe. In this way, absolute gas-phase alkali species could be determined in situ, continuously, with sub-ppb sensitivity, directly in the flue gas. A hard coal was fired in the range 1000–1300 °C, for residence times in the range 3–5 s and for air numbers λ (air/fuel ratios) from 1.15 to 1.50. In addition, the amount of chlorine, water vapor and sulfur, respectively, was increased in known amounts by controlled dosing of HCl, H₂O and SO₂ into the combustion gas to determine effects of these components on release or capture of the alkali species. The experimental results are also compared with values calculated using ash/fuel analyses and sequential extraction to obtain a fuller picture of alkali release in pulverized fuel combustion.     

Char characteristics and particulate matter formation during Chinese bituminous coal combustion

The characteristics of char particles and their effects on the emission of particulate matter (PM) from the combustion of a Chinese bituminous coal were studied in a laboratory-scale drop tube furnace. The raw coal was pulverized and divided into three sizes, <63, 63–100, and 100–200 μm. These coal samples were subjected to pyrolysis in N₂ and combusted in 20 and 50% O₂ at 1373, 1523, and 1673 K, respectively. Char samples were obtained by glass fiber filters with a pore size of 0.3 μm, and combustion-derived PM was size-segregated by a low pressure impactor (LPI) into different sizes ranging from 10.0 to 0.3 μm. The characteristics of char particles, including particle size distribution, surface area, pore size distribution, swelling behavior and morphology property, were studied. The results show that, coal particle size and pyrolysis temperature have significant influence on the char characteristics. The swelling ratios of char samples increase with temperature increasing from 1373 to 1523 K, then decrease when the temperature further increases to 1623 K. At the same temperature, the swelling ratios of the three size fractions are markedly different. The finer the particle size, the higher the swelling ratio. The decrease of swelling ratio at high temperature is mainly attributed to the high heating rate, but char fragmentation at high temperature may also account for the decrease of swelling ratio. The supermicron particles (1–10 μm) are primarily spherical, and most of them have smooth surfaces. Decreasing coal particle size and increasing the oxygen concentration lead to more supermicron-sized PM formation. The influence of combustion temperature on supermicron-sized PM emission greatly depends on the oxygen concentration.     

Effect of water vapour on particulate matter emission during oxyfuel combustion of char and in situ volatiles generated from rapid pyrolysis of chromated-copper-arsenate-treated wood

This paper reports the effect of water vapour on particulate matter (PM) during the separate combustion of in situ volatiles and char generated from chromated-copper-arsenate-treated (CCAT) wood at 1300 °C. Combustion of in situ volatiles produces only PM with aerodynamic diameter?<1?µm (i.e., PM₁), dominantly PM with aerodynamic diameter?<0.1?µm (i.e., PM_0.1). Water vapour could significantly enhance the nucleation, coagulation and condensation of fine particles and reduce the capture of Na and K by the alumina reactor tube via reduced formation of alkali aluminates, leading to increases in both yield and modal diameter of PM_0.1. Water vapour could also enhance char fragmentation hence increase the yield of PM with aerodynamic diameter between 1 and 10?µm (i.e., PM_1–10) during char combustion. For trace elements, during in situ volatiles combustion, volatile elements (As, Cr, Ni, Cu and Pb) are only presented in PM₁ and water vapour alters the particle size distributions (PSDs) but has little effect on the yields of these trace elements. During char combustion, As, Cr, Cu and Ni are present in both PM₁ and PM_1–10 while the non-volatile Mn and Ti are only present in PM_1–10. Increasing water vapour content increases the yields of As, Cr, Cu, Ni, Mn and Ti in PM_1-10 due to enhanced char fragmentation. During char combustion, water vapour also originates less oxidising conditions locally for enhancing As release, promotes the generation of gaseous chromium oxyhydroxides and inhabits the production of NiCl₂ (g), leading to increased yields of As and Cr and decreased yield of Ni in PM_0.1.     

On the reaction mechanism of CO2 reforming of methane over a bed of coal char

CO₂ reforming of methane was studied over a bed of coal char in a fixed bed reactor at temperatures between 1073 and 1223 K and atmospheric pressure with a feed composition of CH₄/CO₂/N₂ in the ratio of 1:1:8. Experimental results showed that the char was an effective catalyst for the production of syngas with a maximum H₂/CO ratio of one. It was also found that high H₂/CO ratios were favoured by low pressures and moderate to high temperatures. These results are supported by thermodynamic calculations. A mechanism of seven overall reactions was studied and three catalytic reactions of CH₄ decomposition, char gasification and the Boudouard reaction was identified as being of major importance. The first reaction produces carbon and H₂, the second consumes carbon, and the third (the Boudouard reaction) converts CO₂ to CO while consuming carbon. Equilibrium calculations and experimental results showed that any water present reacts to form H₂ and carbon oxides in the range of temperatures and pressures studied. Carbon deposition over the char bed is the major cause of deactivation. The rate of carbon formation depends on the kinetic balance between the surface reaction of the adsorbed hydrocarbons with oxygen containing species and the further dissociation of the hydrocarbon.     

An analysis of the transient combustion and burnout time of carbon particles

The various coupled and transient processes controlling the gasification mechanism and burnout time of carbon particles were analyzed, with emphasis on the influence of the initial particle size for the size range that is relevant to the firing of pulverized solid fuels. The formulation recognizes the suppression of the envelop gas-phase CO flame because of the small particle size, and allows for the three surface reactions of C + O₂, C + CO₂, and C + H₂O, as well as radiation heat transfer because of the potential high temperature attainable by the carbon particle. Results show that while the particle temperature continuously increases during the combustion of sufficiently large particles, the gasification actually consists of three phases: namely an initial particle heating period, an activation period for the surface reactions, and a diffusion-controlled, d²-law gasification period characterized by perpetually maximized surface reaction rates in spite of the continuously decreasing particle size. Radiation heat transfer is shown to have the same magnitude as those of reaction heat release and conduction, and actively affects the particle gasification response. For smaller particles, activation of the surface reactions is either substantially delayed subsequent to the initial heating period, or is completely suppressed, which respectively leads to either long burnout times or incomplete particle gasification. Influences due to the ambient oxygen concentration and the presence of CO₂ and H₂O as the oxidizer were also studied. Comparisons with literature experimental data show adequate agreement.     

The effect of potassium bromide and sodium carbonate on coal char combustion reactivity

The addition of halogens, particularly iodine, to the gas during coal char oxidation has been used in previous studies to quench gas-phase chemistry, thereby allowing one to separate the effects of homogeneous and heterogeneous reactions. Halogen addition suppresses the gas-phase radicals to near-equilibrium levels. A similar effect can be expected from other compounds with high efficiency as fire suppressants, such as alkali metals. The effectiveness of the use of additives in distinguishing homogeneous and heterogeneous reactions during char oxidation relies on the assumption that radicals are suppressed while heterogeneous reactions occurring on the char surface are not affected. The present work tests this assumption for potassium bromide (KBr) and sodium carbonate (Na₂CO₃) reacting with a pulverized eastern bituminous coal char during oxidation. An increase in CO and a slight reduction in particle temperature were observed with the addition of KBr, consistent with known effects of halogens on gas-phase chemistry. An increase in particle size was also observed with the KBr addition. This observation and the results of model calculations suggest that there is significant incorporation of liquid KBr on the char surface under the conditions examined. With Na₂CO₃ addition, the particle temperature did not change, the particle size showed a slight decrease, and CO production increased. Although the mechanisms for Na interaction with radicals at combustion conditions are not well established, char oxidation modeling suggests that a decrease in OH concentration in the particle boundary layer is the cause for the observed increase in CO production. It is concluded that Na₂CO₃ has clear advantages over KBr for inhibiting gas-phase chemistry without affecting char oxidation for the conditions investigated here.     

Insight into the calcium carboxylate release behavior during Zhundong coal pyrolysis and combustion

In this paper, the dynamic behavior of calcium carboxylate release during Zhundong coal pyrolysis and combustion is studied via reactive molecular dynamics (ReaxFF MD) simulation. The molecular structure model of Zhundong coal is constructed based on the combination of the classic Hatcher coal model and experimental characterizations. Pyrolysis simulations on the coal model are performed at different temperatures ranging from 2000 K to 2800 K. The pyrolysis experiments are also carried out to validate the ReaxFF simulation. The results show that most of the calcium are released into the volatiles by the thermal decomposition of CM-Ca (coal/char matrix with calcium bonded) after releasing CO₂. The distributions of the calcium bonded to gas, tar and inorganics as well as the atomic calcium in the volatiles are quantitatively classified. The thermal cracking of tar fragments are significant at high temperatures leading to the conversion of calcium from tar into the organic gas. Furthermore, the nascent char model is constructed to study the release behavior of calcium in char combustion stage. The calcium is initially released in the form of oxidized calcium and atomic calcium. With increasing temperature, the oxidized calcium trends to convert to the organically bonded calcium. By using the Arrhenius expression, the kinetic parameters for the release of calcium into various species during pyrolysis and char combustion stages are quantitatively determined.     

三维煤粉燃烧全双流体模型的数值模拟

1引言目前煤粉燃烧综合模型最为广泛的是以轨道模型为基础，美国杨伯翰大学的先进燃烧工程中心（CERC）自1980年起研制二维煤粉燃烧程序PCGC－2，从1990年起研制三维煤粉燃烧的PCGC－3程序[1]。与轨道模型发展的同时，美国Rabcock＆Wilcox公司Fiveland[2]等人研制了FURMO程序，用无滑移模型对560MW侧墙喷燃煤粉炉进行了三维全模拟。其特点是首次用全欧拉的处理方法计算三维煤粉燃烧过程，其不足之处是不考虑气粒两相间的速度滑移和温度滑移．总的看来，用轨道模型模拟煤粉燃烧，易于考虑颗粒反应经历，也可给出两相之间的速度及温…     

Interaction mechanism among CO,H2S and CuO oxygen carrier in chemical looping combustion: A density functional theory calculation study

When using coal-derived syngas or coal as fuel in chemical looping combustion (CLC), CO as a representative pyrolysis/gasification product and H₂S as the main sulfurous gas coexist in fuel reactor. Either CO or H₂S can absorb on the surface of CuO (the active component of Cu-based oxygen carriers), and reactions will occur among them. In this study, density functional theory (DFT) calculations are conducted to investigate the interaction among H₂S, CO, and CuO, including: the reaction between CO and H₂S over CuO particle, the influence of CO on the H₂S dissociation and further reaction process, and the impact of H₂S dissociation products on CO oxidation. Firstly, the co-adsorption results suggest that H₂S might directly react with CO to produce COS via the Eley–Rideal mechanism, while CO prefers to react with HS* or S* via the Langmuir–Hinshelwood mechanism. This means that the reaction mechanisms between CO and H₂S will change as the H₂S dissociation proceeds, which has already been forecasted by the co-adsorption energies and verified by all of potential Eley–Rideal and Langmuir–Hinshelwood reaction pathways. Then, the influence of CO on the H₂S dissociation process is examined, and it is noted that the presence of CO greatly limits the dissociation of H₂S due to the increased energy barrier of the rate-determining dehydrogenation step. Furthermore, the impact of H₂S dissociation products on CO oxidation by CuO is also investigated. The presence of H₂S and S* significantly supresses the CO oxidation activity, while the presence of HS* slightly promotes the CO oxidation activity. Finally, the complete interaction mechanisms among H₂S, CO, and CuO are concluded. It should be noted that COS will be inevitably produced via the Langmuir–Hinshelwood reaction between surface S* and CO*, which is prior to H₂O generation and subsequent sulfidation reaction.